Database Develop

SX66 ( PH20B ) Flashed with wrong Version need help

I, have Siemens SX66 GSM ( PH20B) Upgraded to wron version and now it boot with colored horizontel straps (red,green,blue,white) and goes to WM 5, with slow to none functions and also lost radio.
Now I, tried with several WM5 versions and it display error message ( Model ID error 100) Can some one help how to remove / clean it and recomend working WM5.

See some post at the bottom of this topic

If you you have lost the Radio, ie, no version number is displayed on cold booting/hard re-set, then all is lost.
As i had the same problem with a phone I was given to fix.
As most/all of the Upgrade programs Check to see what Radio version the phone already has, and if it cant see one it fails
My only course of action was to get the Phone fixed under warenty
Read all about it here

Hope.......
Mine did the same thing, it was sooooo slow that I was thinking about buying a new unit but at the last breath I did the following and it worked:
- Go to the BootLoader screen (Press: Power Switch+Media Player+Recorder+Rest) all at the same time, your PDA should say “Serial” at the top of the screen.
- Plug you PDA to the cradle and it should read “USB” at the top of the screen.
- Use At least TuMa 1.3 with Radio 1.13.
Note:
The upgrade EXE should load up with a picture of the PD at the left side of the screen that DOES NOT look like your SX66…it looks like an HP PDA…!!!
Mine came back to life but sometimes you might have to SOFT reboot your PDA to get the Radio to work (Hard boot then use a third party software to softreboot).
Good luck.

so using the MaUpgradeUt_noID.ZIP and radio rom only you were unsuccessful at flashing?

Black6spdZ said:
so using the MaUpgradeUt_noID.ZIP and radio rom only you were unsuccessful at flashing?
Click to expand...
Click to collapse
I, went through all upgrades without issue but now PDA is so slow it takes ages to change selections..

have you downgraded back to 03se and still have this issue?

You will have to follow the steps very accurately...if you leave any step out you might end up like me at the beginning when my device was sooooo slow it was useless.
I took these steps from this forum...try it
Best Luck…

Thanks for all help did every thing but still some of menu are so slow that take several minutes to open , still looking for some tips and suggestions or if some one one knows how to turn it back to W2003

I, remoed some of programs from my SX66 that seems to be causing problems and were npt compatible with and got my PDA back...its now working awsome...Thanks for all who helped

Kaiser going crazy (looks haunted...) AGAIN - Update2: Not Solved?

Ever since returning from repairs, my Kaiser is giving me more problems than before.
First, I apparently lost the ability to hard reset my phone using the 2 softkeys & soft reset button method.
For more: http://forum.xda-developers.com/showthread.php?t=384581
First thing I did when I got my phone back, was flashing the latest ROM from Dutty (Dutty's Official WM6.1 5.2.19209 Release). After performing numerous installations and soft resets, my device went crazy after yet another installation and soft reset.
Just before my Kaiser takes me to the Today screen after (re)booting, the phonepad pops up and seems to be 'pushing numbers out of itself'. Confused by the explanation? Just take a quick look at the short vid I made.
http://www.youtube.com/watch?v=YGkot2-mbbI
(Fast forward to 01:00 to see it going crazy. Long after the vid ends this continues)
Anyone got a clue as to why this is happening? Or has my incompetence reached new heights and is that to blame for my problems?
Thanks in advance
P.S.: In the meantime I have hard resetted my device, but I'm still curious...

call at&t and get a replacement. Easiest thing to do.

Try load the factory default ROM.

FAx
The kaiser has been known to act haunted, thats why it comes in black.
Fix: When applying this fix avoid looking at the screen to avoid the image inside the device that you want to exorcise. Unplug fully and remove battery to prevent an escape through the wires; also ensure that you disconnect any usb devices to avoid an escape to your computer.
Once you have isolated the device. Find the packaging and insert carefully, ensuring that it is packed safely to avoid any breakage resulting in an escape to your home. Then ship to the place you purchased it from and ask them to send you back one that is not possessed.
Good luck.

alexn2 said:
The kaiser has been known to act haunted, thats why it comes in black.
Fix: When applying this fix avoid looking at the screen to avoid the image inside the device that you want to exorcise. Unplug fully and remove battery to prevent an escape through the wires; also ensure that you disconnect any usb devices to avoid an escape to your computer.
Once you have isolated the device. Find the packaging and insert carefully, ensuring that it is packed safely to avoid any breakage resulting in an escape to your home. Then ship to the place you purchased it from and ask them to send you back one that is not possessed.
Good luck.
Click to expand...
Click to collapse
Very dramatic - you don't work in Hollywood do you?

gqstatus0685 said:
call at&t and get a replacement. Easiest thing to do.
Click to expand...
Click to collapse
He's in Belgium

ach2 said:
Very dramatic - you don't work in Hollywood do you?
Click to expand...
Click to collapse
Is that a hint for a career change...... the loss of one's tilt is quite a dramatic event.

@alexn2
I already called in help from the Vatican, but it will take some days before the first batch of exorcists arrives (haunted was a sarcastic expression). Any explanation in the meantime?
@gqstatus0685
This device is a replacement which I got back last week. But it seems to me that I will need to send it back again. Another week without my Kaiser...

alexn2 said:
Is that a hint for a career change...... the loss of one's tilt is quite a dramatic event.
Click to expand...
Click to collapse
care to sign up for ma 4th installement of the exorcist?

Damn this is scary. Call the Ghost Busters!!

WTF?
I just don't get it...
I now have my 3rd Kaiser, since I had issues with the first two. One of the problems my second phone had was the 'haunted' problem as described above.
My Kaiser has been working like a charm for several weeks. I first used the stock ROM, then switched to Dutty's ROMs. I used 3 ROMs: Apr16, Apr29 and Jun07 release.
I installed the Jun07 release today. After installing and configuring the same software I had before upgrading the ROM, guess what?
HAUNTED AGAIN... WTF?
I loaded the ROM, did multiple hard-resets, soft-resetted after customization, loaded CABs, configured them, rebooted several times and when I had finally configured every app => TOTAL Clusterf*ck... (again)
Sometimes it does boot normally BUT when I press the 'Send'-button and the dialer opens => Kaiser goes LOCO again...
Anyone got any idea as to why this happens?
NOTE: I have the latest SPL + Radio NEON 1.58.25.17 (included in the ROM)

I did some additional testing. I had SPB Pocket Plus installed an had the Safe Boot option enabled. So I did some testing in safe mode.
The phone boots 'normally' to safe mode. No apps or services are loaded, and I can open the dialer and even enter numbers to dial. But when I try to delete a number using the backspace in the dialer => again haunted

I just discovered the problem. I always try to install most of my apps to my Storage Card.
Some of those apps is the Microsoft RDP (remote desktop) client.
Installing it to the Storage Card caused the phone to go crazy. It has to be installed to the Main Memory.
NOTE: After discovering the problem, I did find other posts across the forum reporting problems if the app isn't installed to the main memory. Since I found the cab on someone's 4Shared account, I wasn't aware of the installation requirements.
Thanks anyway for the support given

As posted before, I very recently flashed Dutty's Diamond V1 Build 19588 ROM (Jun07).
Today I tried playing WMV files with Windows Media Player for some performance testing. I loaded my first file and whenever I tried something, like fast-forward, switch to fullscreen mode,... my phone crashed and soft-resetted itself.
Guess what I got when the phone booted => The crazy dialer (haunted edition)... It kept doing this after every soft-reset until I removed the MicroSD card. The video I was trying to play was located on the Storage Card, so there might be a relation.
While I have done additional testing under the same circumstances, I haven't been able to simulate the problem.
I'm still clueless, so as always are ideas welcome...

Tilt Freezes at Radio Splash...Bad Blocks!

Hi guys,
Well, I've searched the forum and get close...but no cigar. So, I'll go ahead and ask.
I have an AT&T Tilt, Flashed the 6.1 from XDA MONTHS ago, and have been running Slither's Cube...not even all the time...as well as the HTC Home Customizer.
Yep, that's it.
Well, I have purchased another Tilt with a busted screen (otherwise absolutely fine) for $30 and am waiting to afford a new screen for it...at which time I'll have a backup and then the Cooking and Flashing will begin in earnest!
But I digress. Here is the sequence of events, and where I am at now:
1) Went to hang up from a phone call (BT headset active) by pressing the "Hang Up" Button...no response from the phone.
2) Pressed the Power Button...no response.
3) Slid open the Keyboard...no response.
4) Held the Power Button...no response.
5) Dumped the battery and rebooted...AT&T Splash then Radio Info...stays right there. Screen will dim after awhile, but never goes out. Rebrightens when removing external Power.
6) Soft Reset...same result.
7) Only way to Power Down is dump the battery.
8) Removed SD and SIM...attempted Bootloader Screen
9) Bootloader DOES show up:
KAIS1*0
SPL-1.93.0000
CPLD-8
Serial
10) I don't remember if there was anything with "Serial"...like a number or such...when I looked at it last (when flashing 6.1) so that may or may not be significant. There's nothing there now.
11) My Radios show up as:
R 1.27.14.09
G 22.45.88.07H
D 1.62.00.00
I am avoiding Hard Reset or Re-Flash until I can at least figure out what happened...if anyone has any ideas...or find out that this is common and that's the best or only way to solve it etc.
Since I haven't found anything quite like this in the Forum, I'm presuming that it may not be so common and I may...or may NOT...be able to find a way back before going that path. As well, I really don't want to send it off for repair...although I have insurance and coverage through Hawk (our AT&T Provider) that would be reasonable for repair ($35) but perhaps inordinate for rreplacement ($175). I'd like to be able to resolve this myself, but not knowing what may be wrong leaves me only with Hard Reset and/or Re-Flash alternatives...if those will even work...so out goes the question:
Has anybody run into this or have any idea of why it happened or the BEST recourse to resolve it?
Thanks in advance for any and all info, y'all are awesome and I truly appreciate your help...
RAF

These phones freeze all the time. Software conflicts, too much running at once, and it just feels like screwing you when you need it most. And of course all of a sudden, the hardware just crashes and never works again.
It looks like a hard reset will solve your problems, unfortunately, unless you do regular backups, you will lose all your info.

Thanks denco7!
Well, this is the first time it has locked up that early in the boot...all others have been easily resolved.
Hard Reset is not an issue with Data...I do keep my phone (data) backed up and have most of my volatiles on the SD.
And, honestly, I don't mind having to reflash or reinstall my apps...at least not yet, once I start cooking my own I feel I'll get a bit testy when I have to 'start over'.
I should probably find a good full backup app to snapshot the whole phone, then just put it back on when things 'happen'.
I do have a full backup from December using the 'supplied' app, so it will at least have most of the tweaks in it.
I'm gonna do the Hard Reset and see if that clears this, but I must say I'm not that hopeful.
Not really an expert...not a noob either...but this technology is just not rocket science, and I can actually do that along with quite a bit more.
Don't ask me to write a driver tho...I respect anyone that has that kind of patience!
Suffice to say, this just doesn't "feel" like a resetable issue...but I'm game. I'll update once attempted.
Thanks again, see you on the other side...
RAF
Okay...no joy on the Hard Reset. Behavior has stayed the same. Kinda expected that tho...
Next stop, Re-flash the ROM. I'm gonna check on latest releases of 'Official' HTC ROMs...but if anyone has any suggestions I'm open.
I'm still hoping that someone out there knows what happened here, it would be helpful to know the 'why'.
Thanks again...

not so much a suggestion but a correction. You don't have a wm6.1 rom but actually have a wm6 rom because the radio you have flashed i.e. R 1.27.14.09
is a wm6 radio not wm6.1 and that radio is only compatible with the following roms:
AT&T 1.60.502.3
AT&T 1.61.502.2
AT&T 1.62.502.0
Q-Mobile 1.2 AT&T Version
(source for above info: http://forum.xda-developers.com/showthread.php?t=393182)
so make sure that your rom matches the radio you have. I would recommend that if flashing is not something new to you than go ahead and upgrade your rom and radio to wm6.1 rom and see if the issue presists.
hope this helps

first post you stated you have a 6.1 rom but your spl is for a 6.0 rom, either your not on a 6.1 rom or your on the wrong SPL and should HARDspl if your flashing custom roms.

Thanks Guys...
I had it in my head that I went to 6.1 when I flashed it last...went out and looked at the file and sure enough it was 6.0.
This is what happens when u have 7 kids, 6 female and 4 of those in college...I'm too broke to pay attention.
No not new to flashing, and when I can get home before 10-11p some night...or this weekend...that's my plan.
Looking for the best choice 6.1 to flash and attempt to bring it back, but still curious as to the behavior in the first place.
Thanks for pointing out my ADD, and all comments are welcome...
Hoping for the un-bricking soon...
RAF

Now I'm REALLY Currious...and Frustrated! A Little Help Please...
Okay,
So I flashed the latest HTC Factory ROM: AT&T Tilt Windows Mobile 6.1 Software (ROM Version 3.57.502.2 WWE).
I wanted to do something mild at first before taking too many big steps...'small steps Ellie, smal steps'.
Once the Bootloader was up with USB showing at the bottom, I was certain I would at least have a connection to the Phone.
Of course with no ActiveSync or recognition from the PC, I simply ran the EXE and ignored the one line about making sure ActiveSync had a connection.
The only oddity was that at 13%, the Phone went from the "% Screen" back to the Bootloader Screen for a few seconds then continued normally to sucessful completion.
When it rebooted, it stayed at the AT&T initial splash and now NEVER shows the Radio or Protocol versions...just the initial splash.
As well, it does not dim the backlight after awhile as it used to nor do I ever get a Power Light...just plain LOCKED.
There is also still no way to Power Down the Phone except for removing the Battery.
Although I've never used MTTY, I'm wondering if that is now my only hope...and am currious as to the proper procedure for this particular circumstance.
I'm still searching the Forum for MTTY uses and info, but I would be appreciative if one of the Seniors could point me in the right direction.
Also, if ANYONE knows what may have caused this glitch in the first place it would help me to determine the best recourse.
Thanks again in advance to all...
RAF

Rustafergi said:
Okay,
So I flashed the latest HTC Factory ROM: AT&T Tilt Windows Mobile 6.1 Software (ROM Version 3.57.502.2 WWE).
I wanted to do something mild at first before taking too many big steps...'small steps Ellie, smal steps'.
Once the Bootloader was up with USB showing at the bottom, I was certain I would at least have a connection to the Phone.
Of course with no ActiveSync or recognition from the PC, I simply ran the EXE and ignored the one line about making sure ActiveSync had a connection.
The only oddity was that at 13%, the Phone went from the "% Screen" back to the Bootloader Screen for a few seconds then continued normally to sucessful completion.
When it rebooted, it stayed at the AT&T initial splash and now NEVER shows the Radio or Protocol versions...just the initial splash.
As well, it does not dim the backlight after awhile as it used to nor do I ever get a Power Light...just plain LOCKED.
There is also still no way to Power Down the Phone except for removing the Battery.
Although I've never used MTTY, I'm wondering if that is now my only hope...and am currious as to the proper procedure for this particular circumstance.
I'm still searching the Forum for MTTY uses and info, but I would be appreciative if one of the Seniors could point me in the right direction.
Also, if ANYONE knows what may have caused this glitch in the first place it would help me to determine the best recourse.
Thanks again in advance to all...
RAF
Click to expand...
Click to collapse
If you cannot flash a 6.1 rom or install the correct hard spl I would not even attempt using MTTY. Go to the rom section of this forum. Look for "spl rollup thread" it is a sticky from DaveShaw. Pick any 3.xx hard spl's for 6.1 rom and download. Now download jumpspl and place it somewhere on your device other than your memory card. Now run jumpspl and follow the rest of the directions in that thread. After you installed the correct SPL find a 6.1 rom and flash your device. If your sound doesn't work change your radio to a compatible radio, which would be listed in the "ultimate radio thread" by alltheway.
These are the basics. Hope it helps.

Rustafergi said:
Okay,
So I flashed the latest HTC Factory ROM: AT&T Tilt Windows Mobile 6.1 Software (ROM Version 3.57.502.2 WWE).
I wanted to do something mild at first before taking too many big steps...'small steps Ellie, smal steps'.
Once the Bootloader was up with USB showing at the bottom, I was certain I would at least have a connection to the Phone.
Of course with no ActiveSync or recognition from the PC, I simply ran the EXE and ignored the one line about making sure ActiveSync had a connection.
The only oddity was that at 13%, the Phone went from the "% Screen" back to the Bootloader Screen for a few seconds then continued normally to sucessful completion.
When it rebooted, it stayed at the AT&T initial splash and now NEVER shows the Radio or Protocol versions...just the initial splash.
As well, it does not dim the backlight after awhile as it used to nor do I ever get a Power Light...just plain LOCKED.
There is also still no way to Power Down the Phone except for removing the Battery.
Although I've never used MTTY, I'm wondering if that is now my only hope...and am currious as to the proper procedure for this particular circumstance.
I'm still searching the Forum for MTTY uses and info, but I would be appreciative if one of the Seniors could point me in the right direction.
Also, if ANYONE knows what may have caused this glitch in the first place it would help me to determine the best recourse.
Thanks again in advance to all...
RAF
Click to expand...
Click to collapse
Wow! I think you missed the advice and wisdom given to you about NOT FLASHING a 6.1 ROM with the SPL for a 6.0 ROM...
Anyways, lets see if we can help... I don't think you are going to be able to flash a SPL, as you probably can't even get an active sync connection to copy over the files...
So, try getting into boot loader screen; you hold down the camera button and then press in the rest button and hold that until a tri-color screen appears...
Then tell us exactly what it says, just to make sure we know which SPL you have... Then I will post a link to the exact ROM you need to flash to hopefully bring her back to life.
If you are not able to get into boot loader, which wouldn't surprise me, someone else with more experience un-bricking will have to help.

Some Answers and Info...Still Confused
redbandana said:
If you cannot flash a 6.1 rom or install the correct hard spl I would not even attempt using MTTY. Go to the rom section of this forum. Look for "spl rollup thread" it is a sticky from DaveShaw. Pick any 3.xx hard spl's for 6.1 rom and download. Now download jumpspl and place it somewhere on your device other than your memory card. Now run jumpspl and follow the rest of the directions in that thread. After you installed the correct SPL find a 6.1 rom and flash your device. If your sound doesn't work change your radio to a compatible radio, which would be listed in the "ultimate radio thread" by alltheway.
These are the basics. Hope it helps.
Click to expand...
Click to collapse
pjcforpres said:
Wow! I think you missed the advice and wisdom given to you about NOT FLASHING a 6.1 ROM with the SPL for a 6.0 ROM...
Anyways, lets see if we can help... I don't think you are going to be able to flash a SPL, as you probably can't even get an active sync connection to copy over the files...
So, try getting into boot loader screen; you hold down the camera button and then press in the rest button and hold that until a tri-color screen appears...
Then tell us exactly what it says, just to make sure we know which SPL you have... Then I will post a link to the exact ROM you need to flash to hopefully bring her back to life.
If you are not able to get into boot loader, which wouldn't surprise me, someone else with more experience un-bricking will have to help.
Click to expand...
Click to collapse
Hi again,
Thanks to redbandana and pjcforpres for the responses...I thought I might not get anymore!
I'll start with pjcforpres,
First, my appologies if I have not been specific enough on my descriptions...I've been attempting to be more succinct (I'm not so good at that).
This was a Stock ROM Tilt, then I had flashed RUU_Kaiser_CINGULAR_WWE_1.62.502.0_radio_sign_22.45.88.07_1.27.14.09R2_Ship.exe quite awhile back...shortly after it was available.
I added Slither's Cube and the HTC Home Screen and Customizer and have run it that way since then.
Somehow, I got it in my head that I had flashed 6.1 but I was flat out mistaken...hence the comment in the earlier part of the thread.
Then we get to the #1 post in this thread...add some confusion and voila.
The ref'd 6.1 flash was also Stock...RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe...and I thought I read everything, incl that it replaces the SPL.
Durring the flash, it pauses @ 13%, the USB disconnect 'bing' sounds and the Bootloader screen reappears showing SPL-3.02.000.
Then, the USB reconnect 'bing' sounds, goes back to the % screen and then completes the flash successfully.
My Bootloader screen is now:
KAIS1*0
SPL-3.56.000
CPLD-8
So...did I miss something and screw up? Or was I on the right track?
And redbandana,
It did successfully flash 6.1, but it still doesn't start...specifically, get passed the initial AT&T Splash.
Although I had already thought of going to JockyW's HardSPL 3.29, I cannot 'see' the phone in XP and therefore cannot get JumpSPL onto it...so, no HardSPL (unless I missed something else in the threads).
It DOES however give me the USB 'bing' sound when I go into the Bootloader...but clicking on the "Mobile Device" icon in Windows Exploder leaves a 'blank' right pane.
Before your post, I had read up on MTTY and noted the DON'Ts...like DON'T use task 2a!...and found several threads with commands.
None of the info commands seem to fuction, like info 2, info 7 or info 8 so I don't have much 'info' there.
One of the things I tried was 'task 28' to format the thing in case there was some corruption...this was the response:
Cmd>task 28
Format start
Storage start sector=0xC2C0, total sector=0xF000
Storage start block=800, total block=960
Total Bad Block in CE: 1
Erase physical block from 1091 to 2032
formatstorage Bad block found: 1397
formatstorage Bad block found: 1398
si backup: Erase physical block from 2032 to 2048
Format end
So I looked for 'bad blocks' on the Forum and there are suggestions to contact JockyW and GSLEON3 for more help.
I haven't as yet done this thinking I can work my way through this by searching the Forum and monitoring this Post.
My searches for MTTY Commands have shown me that there are different Commands for different SPLs, and the info is way scattered and confusing.
It is becoming clear(er) to me that I have an issue that is not that normal...or at least not with an intermediate level 'fix'.
That's why I asked for more help in the right direction, I feel like I've hit this pretty hard and done alot of footwork on my own.
I also feel like I'm running out of options and may resort to bugging JockyW and GSLEON3...unless there are any more suggestions
PLEASE let me know if there is more info that I can provide to narrow this down, or some procedure to attemt, or an MTTY comand that will give us more info, or another search in the Forum for something specific I've missed...or simply some PFM that can be performed...and I'll be HAPPY to comply!
Thanks again...and again...for the assistance, my grattitude and appreciation out!
RAF

I am going to be short and swet for the moment... my computer crashed so I am solely on my phone until I work again around 2 central time USA...
Good news is that there is a chance without MTTY to get you running, and if not, those with the knowledge are very hepful and patient.
I will do the searches tomorrow for the stock ROM you should try, and give a walk through on how to flash using a micro SD card.
I am out for now, and will get back to you as soon as I can tomorrow.

Patient and Prepared
Thanks pjc...if we can fix this I'll vote for you
I sincerely appreciate the assistace, and PLEASE let me know if there's any research I can do to facilitate.
If you're willing, let me know if I took a wrong turn somewhere or if I did something to make this worse...I like to learn from my mistakes (I AM pretty good at those...)
I just got the new screen for my backup Tilt and I'll be swapping that out tomorrow (uh...today) sometime, so I'll have a reference phone soon.
Askew but relevant, I'm on day 12 of a nasty cranial muscle spasm and 3 days into meds for it...so we'll see if I can stay focused
Thanks again and in advance...
RAF...Tilted

http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
Try downloading from here... it is the 100% official AT&T Tilt 6.1 ROM, plus upgrade tool.
This includes everything you need, and is probably what you flashed already, but it sounds like you had a bad flash or something...
Make sure your computer doesn't go into hibernate during this process, and that you don't have anything running other than the update program and activesync...
Also, make sure when you run the update program, you right click and select 'run as administrator' or 'run as' then in the menu that comes after that select administrator.
If you can't establish an activesync connection, or if you are using Vista, and thus no Windows Mobile Device Center connection can be established, let me know, and I will track down the ROM by itself and the Radio by itself and walk you through that.
This should be the easiest fix, though, so we will try this first.

Been There, Done That...I Think ?!?
pjcforpres said:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
1] Try downloading from here... it is the 100% official AT&T Tilt 6.1 ROM, plus upgrade tool.
2] This includes everything you need, and is probably what you flashed already, but it sounds like you had a bad flash or something...
Make sure your computer doesn't go into hibernate during this process, and that you don't have anything running other than the update program and activesync...
3] Also, make sure when you run the update program, you right click and select 'run as administrator' or 'run as' then in the menu that comes after that select administrator.
If you can't establish an activesync connection, or if you are using Vista, and thus no Windows Mobile Device Center connection can be established, let me know, and I will track down the ROM by itself and the Radio by itself and walk you through that.
This should be the easiest fix, though, so we will try this first.
Click to expand...
Click to collapse
1] Yep, same one I have already flashed several times to determine if there was a pattern.
2] ActiveSync will not connect...remember from #1 in this post:
1) Went to hang up from a phone call (BT headset active) by pressing the "Hang Up" Button...no response from the phone.
2) Pressed the Power Button...no response.
3) Slid open the Keyboard...no response.
4) Held the Power Button...no response.
5) Dumped the battery and rebooted...AT&T Splash then Radio Info...stays right there. Screen will dim after awhile, but never goes out. Rebrightens when removing external Power.
6) Soft Reset...same result.
7) Only way to Power Down is dump the battery.
8) Removed SD and SIM...attempted Bootloader Screen
9) Bootloader DOES show up:
KAIS1*0
SPL-1.93.0000
CPLD-8
I've never gotten passed the initial AT&T Splash since then...no matter soft hard reset flash the 6.0 ROM that was already on it or this 6.1 version.
Only difference is when I flashed this 6.1 ROM, the Radio and Protocol Versions that normally pop up at the bottom in red no longer pop up.
It now stays at the initial AT&T Splash, no versions, and never dims the backlight.
The ONLY time my Laptop 'sees' the Phone is when I put in into the Bootloader I get the USB 'bu-bingk'.
MTTY can see it, and the ROM Upgrades see it and run successfully...but Exploder can't and neither does ActiveSync.
Just to clarify that I've been there more than once...
3] Well, that I have not attempted...but all my previous flashes have gone fine (I am the only user on my Alenware Aurora m7700...and effectively I AM the Administrator), so I'll attempt that...(see next).
I downloaded, overwrote and ran this 6.1 ROM again...I set this XP install with me as the only Administrator (only user other than Guest), and I want to point something out that may be significant:
The Screnshots below show that there's no info in the Current Image Version area, I click on 'Update' and get the 2nd one.
(okay, sorry I haven't attempted very hard to embrace multiquote or embed a screenshot yet )
But this has happened every attemp to reflash after the initial sequence of events. As well, the same events recurred during the flash as all attempts before:
Durring the flash, it pauses @ 13%, the USB disconnect 'bing' sounds and the Bootloader screen reappears showing SPL-3.02.000.
Then, the USB reconnect 'bing' sounds, goes back to the % screen and then completes the flash successfully.
So...did I screw up somewhere? I really thought I had a handle on the 'small steps' that I took..it was the 'next steps' that I was mildly trepidatious about.
My understanding and instincts point to the 'bad blocks' errors durring the MTTY 'task 28' format, but I can't find anything pertinent to 'do' about it in the Forums...other than contacting JockyW or GSLEON3.
I want to try SOMETHING on my own before I go bothering them with a PM...although I've read (and even learned) alot here recently on TOP of what I had already learned over the last 2½ years, I feel I've got to at least attempt something before begging for help that way.
Still, I haven't found a path to get this basal into the core of the phone to noodle (safely mind you) around and become more adept so that I can solve these issues on my own...and it may be time to capitulate.
Let me know if you've spotted an error on my part...something I did or didn't do...or if there's another path I should take or search in the Forum I should look up.
Thanks ton again...and my appologies to all for my un-succinct pontifications...
(S)tilted...RAF

I don't think you are really doing anything wrong on your part, it just doesn't want to flash right... I had you try the stock stuff again just to make sure it was a clean download, and a clean flash.
I am not sure if it is the SPL not matching the ROM, or the Radio... The MTTY commands do indicate a problem with something not flashing right to the phone. Especially since that download has been recommended and successful so many times for people with a similar situation. I have done a fair amount of looking into this myself, and I have found a couple solutions:
1. Some people found success by flashing the same stock AT&T ROM 2 -5 times, and then it finally caught and worked right.
2. Others found luck by flashing a HardSPL, then new Radio, then new ROM.
3. They PM one of the greats... right now in the Kaiser area, JockyW is amazing! But is mostly focused on newer devices. I would recommend contacting mskip or DaveShaw. They have much more experience than I do, and should have a better idea of exactly what those block errors mean, and the solution....
If I were you I would try one last time doing a hard rest, you may need to hold down the 2 soft keys and the rest button extra long to get it to register... I would also try flashing that same upgrade 1 last time, followed by 1 last shot at a hard rest. If you still have the same stuff going on, I would contact those 2 guys and see what their wisdom says... mskip moderates the "NOOB flashing guide" thread and DaveShaw is a moderator for the Kaiser section in general.

Thanks pjcforpres...Contacting DaveShaw...Any Other Ideas?
Okay, one more time...and, no joy. Held the Soft Keys for 2 mintes solid for the Hard Reset, Reflashed, then another 2min Hard Reset.
I've resorted to sending DaveShaw a PM per the suggestion and will patiently wait for a reply.
In the mean time, if there's ANY other suggestions or a list of MTTY commands that run on the 3.56.000 SPL that can get info from the phone to help determine what the actual problem is or to correct bad blocks I'd be SERIOUSLY appreciative and VERY grateful.
Thanks to all who have responded, and in advance to all who may help from here...
RAF
A Little Updated Info:
Replaced the screen on my 'backup' Tilt, and flashed the RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_s ign_25.88.40.05_1.65.21.18_Ship.exe ROM thaT I had flashed on the 'bricked' one.
It had the same behavior @ 13%, so I'm certain now that the flash went fine...I am even more convinced, with all of the events and symptoms to this point, that the issue lies in the 'bad blocks' reported durring the MTTY task 28 format.
I've left a PM for DaveShaw...and I AM patient...but if there is someone that may be more appropriate for this question I'd like to contact them as well. If anyone knows the right Guru, please let me know.
Thanks again to all...
RAF

Well I'm here at last sorry for the delay in getting back to you - I'm not sure how much I can help you though .
Can you post the output of "info 2" and "info 8" from an MTTY connection to your bootloader.
Also, can you please clarify: are you stuck at the bootloader (red/green/blue) or the splash screen (with R G D)?
Thanks
Dave

DaveShaw said:
Well I'm here at last sorry for the delay in getting back to you - I'm not sure how much I can help you though .
Can you post the output of "info 2" and "info 8" from an MTTY connection to your bootloader.
Also, can you please clarify: are you stuck at the bootloader (red/green/blue) or the splash screen (with R G D)?
Thanks
Dave
Click to expand...
Click to collapse
Wow man, THANKS for just bein here!
That's just it Dave, none of the info commands in MTTY seem to return anything (see #10). I've used MTTY: ver. 0.01 2001 and ver. 1.42 1997-2001 and both report literally nothing for info 2 info 7 or info 8...just another Cmd> prompt. However, (also in #10) I get to the 'bad blocks' ref running "task 28":
Cmd>task 28
Format start
Storage start sector=0xC2C0, total sector=0xF000
Storage start block=800, total block=960
Total Bad Block in CE: 1
Erase physical block from 1091 to 2032
formatstorage Bad block found: 1397
formatstorage Bad block found: 1398
si backup: Erase physical block from 2032 to 2048
Format end
Remember, the stuff in #1 of the thread happens and then I went through all this digging...took it to where I could and posted.
This wasn't a HardSPL fail or a bad Flash... I had BEEN running stock HTC 6.0 WWE with Slither's Cube, the HTC Home Screen and Home Customizer.
RUU_Kaiser_CINGULAR_WWE_1.62.502.0_radio_sign_22.45.88.07_1.27.14.09R2_Ship.exe (flashed 07/20/08)
This isn't a RUUNBH issue either, and I can get into Bootloader and I'm not 'stuck' there...currently:
KAIS1*0
SPL-3.56.000
CPLD-8
I can flash stock ROMs all day long w/no errors...flashed HTC 6.1 WWE on my backup Tilt to be sure the behaviors were the same, and they are exactly.
RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe runs FINE on the backup Tilt.
After flashing the HTC 6.1 WWE on the 'bricked' one however, there is no longer the R G D Radio Protocol info at the bottom of the AT&T Splash after the initial Splash...it was there before the 6.1 flash, and that's where it used to hang: Initial Splash, R G D, hang...backlight eventually dimed but never went out...battery dump only way off.
Now it hangs at the Initial Splash, NO R G D, NO backlight dim...still needs battery dump for off. It ACTS like it's lost it's damn mind...
I'm pretty sure I 'downgraded' back to the 6.0 mentioned above and went thru some similar steps to confirm, but I didn't write it all down and I'm way ADD so I can do that one again and record it all this time...unless that's a bad idea.
I very recently (like as I was searching I saw you had answered my plea...) found some other references to a MFG HardSPL that someone was thinking about working on to fix bad blocks, but I haven't read through it all yet. And, since Exploder and ActiveSync simply can't 'see' the phone, I'm not sure that I could get a HardSPL on the thing in the first place...'cause I can't get no JumpSPL on the phone itself...should've done that back when it was working I guess
I truly believe I'm at the 'needing guru help' level at this point, but if you see something I should do PLEASE point me that way and I'll dive right in. Also, like I've asked others, if you see something I did wrong or in the wrong order or whatever, please let me know that also...there's GOT to be something I can actually LEARN from this.
I warned you I tend to pontificate, but I hope that this clears up where I'm at. ANY help you can provide is fantastic and greatly appreciated, even if it's just to tell me to go somewhere else (I'm kinda used to that )
Thanks again, seriously...
RAF

In that case I have no idea. I think GSLEON3, jockyw2001 or cmonex are going to be the only one's who can help you.
Dave

Bricked my device a second time !!!!

Help needed,
First time I "bricked" my device is about half a year ago.
I installed a ROM (ThaiHugo's age of reason) and after a BSOD in
Windows my Shift Windows Vista Side was broken. Windows Mobile did boot once in a while. Sent it in for free repair, they changed my motherboard and keyboard, and happy I was after.
Today I installed RomeOS Rom, the ROM istelf wasn't really performing well after installation (memory issues, see other post) but after
a few hard resets to see where the problem was (it seems activesync/pushmail) the device stopped booting WinMo alltogether.
So, I dunnit, I bricked my Shift a second time !
I tried hard reset from Vista using Shift Control Center
Tried soft reset from the control center.
Tried Removing the battery completely.
Tried some other things.
Havent tried ECSHift.exe as the link to cmonex site is dead.
Hope you guys want to post that file again ecshift.exe
It seems to be my last resort
------
UPDATE !! UPDATE !!
I download ECShift.exe. performed a mode0, a -reset and a -w (wakeup) and my screen is still black.
I can't seem to perform a task 28, what is the exact syntaxis ?
This is getting worse every minute, I expected with ECshift to restore it.
----------------------------------
UPDATE UPDATE
Ok...so I'm not jumping of the bridge.
It's working again, I managed to flash good ol' ThaiHugo's Age of Reason again.
What I had to do is do a ecshift.exe /bl (entered the bootloader)
Checked if the bootloader was really active with ecshift.exe /gm
Then , switched to WIndows 7 and customRUU thaihugo,
So', I''m back, after some really scary 3 hours. I''ll wait and see
if anyone else has problems with ROMEOS ROM.

So the conclusion is its not bricked
Actually this happened to me many times when i'm testing ROMeO_S
but i dont get worried because I believe cmonex 200% with her HardSPL.
v1_01 has been running with my machine almost 3 days with push enabled both live & exchange server w/o any lock/hang/resets.

Could it be that I clicked on the Pagepool changer once ? I clicked on it, then closed it.
Did that change my ROM ? I just tested again and I don't think I did. One has to really go in and change a value in order to be able to save.
I wonder what the difference is. Another user has posted my exact issues wth this ROM too. I hope you want to keep developing, as it's one of the best looking ROM's today.

Sleep of Death" on (almost) every recent custom & stock ROM

Wouldn't open up a thread for this question but any custom ROM (RECENT EDITIONS) I've tried (NRGZ's, Sergio's, Ark's, Athine's and some others) for several days now have the "dead aka black" screen issue. Tried to find an answer in the original ROM-threads but haven't got any substancial responses. It seems like only few people have these issues. This would make me think the problem is my hardware (German Generic TP2) but the older ROMs of same chefs then run normal and without the dead screen issues.
Please any ideas, solution suggestions or experience share?
Thanks! Ibster
Edit: confirmed solution method described in post# 10 http://forum.xda-developers.com/showpost.php?p=5934002&postcount=10 . Thank you agent 47 big time for the tool you provided!

Ibster said:
Wouldn't open up a thread for this question but any custom ROM (RECENT EDITIONS) I've tried (NRGZ's, Sergio's, Ark's, Athine's and some others) for several days now have the "dead aka black" screen issue. Tried to find an answer in the original ROM-threads but haven't got any substancial responses. It seems like only few people have these issues. This would make me think the problem is my hardware (German Generic TP2) but the older ROMs of same chefs then run normal and without the dead screen issues.
Please any ideas, solution suggestions or experience share?
Thanks! Ibster
Click to expand...
Click to collapse
Is this the same as the "Sleep of Death" (SOD)? In which the phone won't wake from sleep/suspend state and has to be soft-reset?
If not, what's the symptom exactly?

MCbrian said:
Is this the same as the "Sleep of Death" (SOD)? In which the phone won't wake from sleep/suspend state and has to be soft-reset?
If not, what's the symptom exactly?
Click to expand...
Click to collapse
that's exactly what I'm talking about. I didn't know it was called the "sleep of death". I jusst have to softreset the phone all the time. The phone becomes just unuseable.

Ibster said:
that's exactly what I'm talking about. I didn't know it was called the "sleep of death". I jusst have to softreset the phone all the time. The phone becomes just unuseable.
Click to expand...
Click to collapse
i also experience it on my Tilt 2 AT&T unlocked, so i reverted back to Sense 2.1 Euro 1.86.401.0. any solution there, i bought mine from Negrielectronics USA.

Ibster said:
that's exactly what I'm talking about. I didn't know it was called the "sleep of death". I jusst have to softreset the phone all the time. The phone becomes just unuseable.
Click to expand...
Click to collapse
i also exprence it on my Tilt 2. is there any help out there

It's because chiefs have updated their XIP. Ask them to cook a rom for you with the old XIP from stock HTC WM6.5 Sense 2.1 rom.
Ach, that's just my theory based on my experience. I might be wrong, so keep that in mind.

I have a similar issue, but not exactly the sleep of death
A lot of times when I unlock the phone, Sense would not show up, only the taskbar and occasionally the bottom bar
Everything is responsive, the taskbar notification works, hardware buttons works, but not the sense part in the middle
This usually happens when I'm having an SMS conversation
I run this setup most of the time:
WM 6.5.x
Sense 2.5
HD mini lockscreen with Smartlock 2.0F or Lockdevice 1.6

Same here on the SMS black screen
ctbear said:
I have a similar issue, but not exactly the sleep of death
A lot of times when I unlock the phone, Sense would not show up, only the taskbar and occasionally the bottom bar
Everything is responsive, the taskbar notification works, hardware buttons works, but not the sense part in the middle
This usually happens when I'm having an SMS conversation
I run this setup most of the time:
WM 6.5.x
Sense 2.5
HD mini lockscreen with Smartlock 2.0F or Lockdevice 1.6
Click to expand...
Click to collapse
I just started having this problem with the newest Leo Cell Pro, I have not had it with any NRG or Deep Shinig ROMS though but I do like The cell pro details and the others are not without there faults. I like your screenshots and I can hardly wait for that new white theme to come out. I think it will make my phone so much better outdoors and enhance the Windroid look I am workin on.

Apical said:
I just started having this problem with the newest Leo Cell Pro, I have not had it with any NRG or Deep Shinig ROMS though but I do like The cell pro details and the others are not without there faults. I like your screenshots and I can hardly wait for that new white theme to come out. I think it will make my phone so much better outdoors and enhance the Windroid look I am workin on.
Click to expand...
Click to collapse
Yes....interesting that I've never had this issue on Energy's...my guess is he doesn't cook in the latest HTC SMS client which can be unstable at times
Are you talking about Elcondor's GTX theme? Yes that is a very awesome theme
I couldn't wait until 201x version comes out so I made my own Not as good as GTX but I'm half satisfied now

Apical said:
I just started having this problem with the newest Leo Cell Pro, I have not had it with any NRG or Deep Shinig ROMS though but I do like The cell pro details and the others are not without there faults. I like your screenshots and I can hardly wait for that new white theme to come out. I think it will make my phone so much better outdoors and enhance the Windroid look I am workin on.
Click to expand...
Click to collapse
like i mentioned in the the post#1 I had these problems with almost all recent (last two weeks) custom ROM releases, ROMs of different chefs. Because others or the majority of people don't have any problems with that I thought the reason must be hardware issues. yesterday I saw this thread http://forum.xda-developers.com/showthread.php?t=649191 opened by agent_47 where he provides a modified tool:
agent_47 said:
when u flash a rom, you are copying files onto the internal memory (like duh!) but if u repeatadly flash different roms, sometimes files from older version stays behind as when u flash a rom, you just copy and sometimes overwrite files without deleting the older ones. hence at times these older files may create bugs\instability. hardrest donot always fix it.so we use MTTY
Click to expand...
Click to collapse
Well I used it and have flashed to Sergio's Leo Cell Evo 6 and I can confirm that I haven't had any "sleep of death" issues, well still haven't and hope I won't have this "SOD" issue anymore. And when I tried this same ROM before I wasn't even able to make a proper configuration and set up the phone because the phone always froze or as soon the screen went off I wasn't able to activate it back without soft reset.
So maybe this is a solution and could help others who also are having this issue of "sleep of death".
Please if you try the tool from the mentioned agent_47's thread, let know us here because it will be very useful for the rest of the users to finally figure out "the dark side" of their phone and fix it.
Cheers, Ibster

Solution
I had this just recently. Funny side was that I installed an official new ROM from HTC which I just updated. Somehow the phone just didn't want to turn on and show the screen. So just like you guys said, hard-reset did the thing but just when the screen went off, same thing happened.
So what I did was wipe/clean or any other name. Practically did the installation of the rom again. Now, the device works normally and without any problems.
Maybe this happens because some old files of older ROMS sayed on the device itself and started making problems. Anyways, check this thread too, maybe it will explain something more: http://forum.xda-developers.com/showthread.php?t=649191
Or, final explanation. Our Rhodiums have soul inside their little chips and they just simply fu.k with us They tell us they're too tired of so many ROM changes.

I have also had this problem with my two latest official swedish roms (manilla 2.1 and 2.5) cant remember if I had it when I used 6.1. Now I use a cooked rom and still have the issue several times a week. The only thing I had done with my Rhodium before using cooked Rom was flashing hard spl for future use. If its not an inbuilt hardware/software problem from the beginning the only thing I can point at in my case is hard spl?

Originally Posted by agent_47
when u flash a rom, you are copying files onto the internal memory (like duh!) but if u repeatadly flash different roms, sometimes files from older version stays behind as when u flash a rom, you just copy and sometimes overwrite files without deleting the older ones. hence at times these older files may create bugs\instability. hardrest donot always fix it.so we use MTTY
Click to expand...
Click to collapse
back with my kaiser you always had to flash back to stock before going to a new ROM no matter what, for just this very reason...
could flashing back to stock be a 'best practice' that we as users should start doing to help with this issue?

I - have had some xperience with the issue in a few ROMS. Im a loyal flasher of Agent 47s masterpieces. And a month or so ago he had like 2 or 3 builds that had this issue. From what I remember he said that he thought it had to do with some sys evrybody was using to cook roms. and after her came out with this diagnosis and "fixed"(i dont know the technical part of what was fixed) this problem it has never happened since. But a good thing I would say to try is in Agents thread about 4 or so pages from the last page(maybe more or less) but close to the last page he posted a .zip file for this mitty fix. and you essentially flash this zip just like a rom then reflash which ever rom you had or a new one and ta da. Ive also heard of people reflashing a stock rom with results from doing so but from what Agent said is flashing a stock rom then back technicaly "shouldnt" do anything and to definately use mitty. But one of the other frequent valkyrie users that I chat with all the time Mcbrian who posted here on the first page has used the stock rom and did have whatever issue he had cured dont remember what that was tho.
UPDATE- Oh I guess that Agent has a thread for Tool29 so you dont have to search through his thread to find it.

I can confirm agent 47 method is working for me. I no longer have the sleep of death. But its only been half a day. I will report back in a few days.

aichemist said:
I can confirm agent 47 method is working for me. I no longer have the sleep of death. But its only been half a day. I will report back in a few days.
Click to expand...
Click to collapse
Great! I'm glad to hear your confirmation. I now on my side haven't had a sleep of death for three days on the ROM (Cell Leo V6) that previously, before I used the agent_47's tool, couldn't even start normally at all or had extremely many "sleeps of death". But I also noticed overall improvements even though the speed slows down but there are barely any freezes and stability is much better.
Cheers, Ibster

aichemist said:
I can confirm agent 47 method is working for me. I no longer have the sleep of death. But its only been half a day. I will report back in a few days.
Click to expand...
Click to collapse
I did tried agent 47 method at least three times this weekend. I did exactly what agent 47 instructed, flash Energy ROM 23547 with MaxManila = failed to initiated. Flash Tool29 again, reflash Energy ROM 23545 from MicroSD = Failed. Flash Athine OS XTreme = Worked, install MaxManila 3.0 on top of Athine OS Xtreme = Corrupted the manila display. Reflash stock ROM. Flash Deep Shining X.23544 = Worked. Flash Deep Shining X.23547 = Failed.
Look like I can get my phone to work but can't move on from now on! Any suggestion is greatly appreciated!
Thanks

kienkham said:
I did tried agent 47 method at least three times this weekend. I did exactly what agent 47 instructed, flash Energy ROM 23547 with MaxManila = failed to initiated. Flash Tool29 again, reflash Energy ROM 23545 from MicroSD = Failed. Flash Athine OS XTreme = Worked, install MaxManila 3.0 on top of Athine OS Xtreme = Corrupted the manila display. Reflash stock ROM. Flash Deep Shining X.23544 = Worked. Flash Deep Shining X.23547 = Failed.
Look like I can get my phone to work but can't move on from now on! Any suggestion is greatly appreciated!
Thanks
Click to expand...
Click to collapse
I'm not very clear about what you mean by failed. Do you mean you can't flash some of the ROMs or you get screens of death with them?
What I did was this: I took out the SD card. Ran the tool29 modified by agent_47 (see post 10 of this thread). After the tool finished cleaning all internal memory the phone went back on but got stuck in loading. I took the battery out of phone for few seconds and then put it back in. Then I connected the USB cable to the phone and started it in the bootloader mode by quickly pressing and releasing the switch button and then hitting the volume down. On the tricolor screen then it shows USB. Then I just flashed my ROM of choice normally with USB without need to flash from SD. I've done this several time with several ROMs without problems.

Ibster said:
I'm not very clear about what you mean by failed. Do you mean you can't flash some of the ROMs or you get screens of death with them?
What I did was this: I took out the SD card. Ran the tool29 modified by agent_47 (see post 10 of this thread). After the tool finished cleaning all internal memory the phone went back on but got stuck in loading. I took the battery out of phone for few seconds and then put it back in. Then I connected the USB cable to the phone and started it in the bootloader mode by quickly pressing and releasing the switch button and then hitting the volume down. On the tricolor screen then it shows USB. Then I just flashed my ROM of choice normally with USB without need to flash from SD. I've done this several time with several ROMs without problems.
Click to expand...
Click to collapse
Thanks for quick response. Yes. I did exactly what you spelled out in the message. i.e: Remove the memory card, Run Tool29, remove the battery, got into the bootloader mode, then flashed with USB connection. The phone went to the initial setup, I clicked the T-Mobile connection ....etc... then it restart - then stopped at "Launching HTC Sense...." This is = failed for me. i.e: Failed to clean the internal memory!
By the way, if the internal memory is cleaned, shouldn't the Start->Setting->Device Information->Software Information: Incoming Call & Outgoing Call reset to 0?
Thanks

kienkham said:
Thanks for quick response. Yes. I did exactly what you spelled out in the message. i.e: Remove the memory card, Run Tool29, remove the battery, got into the bootloader mode, then flashed with USB connection. The phone went to the initial setup, I clicked the T-Mobile connection ....etc... then it restart - then stopped at "Launching HTC Sense...." This is = failed for me. i.e: Failed to clean the internal memory!
By the way, if the internal memory is cleaned, shouldn't the Start->Setting->Device Information->Software Information: Incoming Call & Outgoing Call reset to 0?
Thanks
Click to expand...
Click to collapse
Your steps should be
1. Shutdown tp2..
2. Remove memory card( I also removed sim card).
3. Turn on tp2, connect through the computer through active sync.
4. Run task 29. Let it load flash, whatever it is doing until it actually reboots.
5. At this point, everything should be cleaned, you don't have a rom or radio anymore, so its blank, so you "pull battery out."
6. Put memory card/sim card back in. Flash radio through boot whatever menu. Soft reset it yourself. Pull battery out again.
7. Flash rom this time, and soft reset it again. Now rom should start setting up.
This shouldn't be rocket science.