Network / Charging LED Woes: - MDA III, XDA III, PDA2k, 9090 Software Upgrading

This is really annoying me now, sometimes when i have done a reset and changed the reg using PHM it works fine, other times it works for 10 mins then starts again. Is there any software that causes this?
i have changed the key
HKLM>drivers\bulitin\nledmgr
dll - NLEDMgr.dll
to
xdll - nledmgr.xdll
this works for 10 mins and the reverts back. I have tried deleting the whole key which freezes the device on a s/reset. I have changed the values completley and the index to 0 but still the same problem. I have checked that the screen flash in notifications is turned off under everything!!!
Please someone help me with this, its doing my head in now :twisted:

Related

Strange behaviours of tuma 1.3

I've done the upgrade by few days, and i've discovered this strange behaviours (don't know if they are already known):
-When i remove and put again the battery on the boot i see
R none
G none
D 5.xxxxx
so radio is disabled,
doing a soft reset repair the situation.
-Occasionally when i turn on flight mode, the phone goes off, and after few seconds it returns on automatically. Sometimes instead, the phone goes off, but the right green led continues to blink.
-When sound is off or volume is 0, and i receive a flash sms message (i've not tested with other events) the event sound play anyway (very annoying).
I have seen the first two problems (I'm using Antz ROM at the moment). I think they are both related...it's as though the ohone itself is crashing and WM5 cannot talk to it, which would explain the lack of driver version numbers on the reset. I had both after messing around with flight mode. It took a power down, wait 15 sec, then soft-reset to get me going.
I suspect it may be something to do with activating flightmode while wireless is on, but that is a complete guess.
fraser said:
I suspect it may be something to do with activating flightmode while wireless is on, but that is a complete guess.
Click to expand...
Click to collapse
Mmm, i think not, because i've discovered while wireless was off.
However i think that the worst problem is the sound playing when volume is 0...
Check those two:
http://forum.xda-developers.com/viewtopic.php?t=47817&highlight=
http://forum.xda-developers.com/viewtopic.php?t=48681&highlight=
I am using the 'standard' WM5 version, and this 'radio none' thing happens to me too when I remove the battery, so I guess it's WM5 related...
anyway soft resetting again works for me too

TyTN II Problems

There seems to be a problem with the Kaiser. After finishing a phone call on the Kaiser the backlight goes off and stays off and I cannot access the Start menu. I can access all other functions but backlight stays off and one still cant get into the Start menu from anywhere on the screen. I have to press the power off button quickly once and then wait a second, press it again to be able to access the start button or the light to come on. This is definitely a bug in the tytn II and I hope HTC is doing something about this.
I have experienced the same thing.
After the phone call. I did not hang up.
Instead the person at the other end hangs up and I tries to navigate away then the phone appears to lock up.
Could not turn the phone off either. Had to wait until the phone turned itself off. Once restarted everything ok...
sudo009 said:
I have experienced the same thing.
After the phone call. I did not hang up.
Instead the person at the other end hangs up and I tries to navigate away then the phone appears to lock up.
Could not turn the phone off either. Had to wait until the phone turned itself off. Once restarted everything ok...
Click to expand...
Click to collapse
I noticed this as well...
pretty crazy.
Hmm I haven't that problem. Danish HTC TyTN II
Do you folks have the password set? I have heard that that can cause this problem. Try to turn off password checking.
Hi @ All, any news about that problem?
I have a solution
I had the same problems and after installing all the ROM's and still have the same problems, I found out that the problem is not in the ROM it is in the 3G network, disable the 3G network and set it to GSM and all the problems will disappear.
This was nothing to do with 3g.
It was a pre-programmed fast sleep setting that was flawed. Download Kaiser Tweak and turn off all the sleep during call options.
Difference in memory in use
I have problem with my TyTN II, I donĀ“t know why, but when I control the state of the memory in use, it seems to be 112 MB in use and 19,4 MB free. But when I control every item (Applicationdata, Confimgr, ProgramFiles etc., even including hidden files) and calculate total then it seems to be only 45 MB in use. Can anyone explain this
thanks

Backlight problem

My screen will be darker after 10 sec.
I can set this again to 5 min. and after a few on and offs it will be back at 10 sec.
This is very annoying!
I thought i had found the problem, but it wasn't.
HKCU/ControlPanel/Backlight/BatteryTimeout setting up to 300. This is 5 minutes. It counts in seconds. But this isn't working.
Please can anyone help me?? A lot more have this problem.
I have the same problem, anyone the solution?
same problem here. I have call the helpdesk of htc they told me to do a hard reset. But it doesn't work for me. They also told me to return the phone when the problem stays afther a hard reset
vipinholland said:
same problem here. I have call the helpdesk of htc they told me to do a hard reset. But it doesn't work for me. They also told me to return the phone when the problem stays after a hard reset
Click to expand...
Click to collapse
i had the same "problem" and indeed, after a hard reset the backlight stays on 2 minutes as my heart wishes. i also use the the option to "auto adjust backlight. i have to admit it is strange...i don't see the connection.
KukurikU said:
i had the same "problem" and indeed, after a hard reset the backlight stays on 2 minutes as my heart wishes. i also use the the option to "auto adjust backlight. i have to admit it is strange...i don't see the connection.
Click to expand...
Click to collapse
yes, my backlight stay's also on for 1 minute(my setting)...hope the sound problem is also gone..
It is a bug in keypad locking
I think the backlight problem only occurs if you are using the keylock feature by pressing the end call button for a couple of seconds.
You can try it out yourself:
1) set your backlight settings to whatever you want and verify it works as intended.
2) Now just normally switch of your phone (not locking the keypad) by pressing the power button, switch back on and verify that the setting is still correct.
3) Then do a soft reset and again verify that the setting is correct.
4) Now lock the keypad by using the end call button (press a couple of seconds until locked).
5) Now unlock the phone and check the backlight settings: they are put back on the default values!! I guess it is a bug in the keypad lock functionality.
Btw, step 2) and 3) are just for verification, you may skip these to reproduce the bug.
Actually, if you use the lock feature of the device (for instance by enabling AutoDeviceLock in the registry, see tweak 18 in the stickied Diamond tweaks thread) the settings are also reset to the default values.
Is this the case for everybody? Or is it just me that it seems the locking feature contains bugs.
FYI...I had this issue from the start when I was running the Asia HK 1.34 ROM image. I flashed it using HardSPL and put the Europe 1.35 image on the device and have not had the problem since. All backlight values work normally as of now....I recommend this if your device is the HK ROM and you're having the issue. Not sure if it'll work for you, but it worked for me....
The solution is simply
You have to change DWORD LockLevel present in HKEY_CURRENT_USER\ControlPanel\BackLight\LockLevel\ to 0 (zero)
And now your time of standby don't change anymore

Can't turn off Kaiser

I know it sound weird, but my Kaiser can't be switched off anymore:
The device is set to turn itself off after 1 minute on batteries.
(Would not switch off automatically.)
When I press the on/off switch nothing happens.
When I press and hold the on/off switch, a dialog comes on that informs that the device will be switched off and unsave information might get lost.
But the "busy icon" for minutes comes on and the Kaiser does not switch off.
Pressing the stylus into the reset hole resets the device, but the problem remains the same.
Any ideas?
Thank you very much in advance.
Thanks
V
PS: I tried to search the forum intensively but I can't bring up useful threads.
Solution found
Looks as if I found how to cure the problem myself:
Everything else but TomTom 7,450 seemed to work on the machine.
TomTom hang when I tried to start it.
And using TomTom was the last thing I did yesterday.
So I tried to uninstall it.
But the WM uninstall hang as well while trying to remove it.
A Reset would not help here either.
So I manually deleted all files in the Navigator Directory
and did a reset.
Ran uninstall again. Then reset.
And from now the device was back to normal as far as the
on/off button is concerned. (YEPP!)
Reinstalled TomTom and all is back to normal as far as I can see.

[Q] Four buttons stopped working: Call/End call/Start/OK. What's the cause / how fix?

Hi, the 4 buttons - Call, End call, Start, and OK - have stopped working on my win mo device (kaiser aka tytn2, wm6.1). Keyboard backlight doesn't turn on when I press them. All other keys (including IE, messaging, both soft keys, and all the other keys on the device) are working though, and backlight is turning on with them. Maybe it's related to the fact that a few days ago after disconnecting this device from charging over usb it almost stopped responding so I had to reboot it (device was probably low on memory too just before reboting because of many programs running). Some time after rebooting I noticed exactly these 4 keys not working. Powering it off and on doesn't solve it, I have tried it several times. Trying to assign another action to OK or Start button didn't help too. Looks to me like soft problem still..
How can I find the cause of the problem and fix it thru some setts, user config, user cfg files, registry, etc?
Please help!
Edit: Also, is there a way I could test if Call, End call, Start or OK button is working at the lowest software levels that are possible (like in bootloader screen, etc.)?
OK

Categories

Resources