UPLOADING DUMP FILE AS NEW ROM - MDA III, XDA III, PDA2k, 9090 Software Upgrading

To make a long story short my BA, CDMA is dead. So the store was nice enough to give me a new device for 5 minutes to play with. I used BUZZ autorun.exe on my storeage card in 2577 dir to grab a rom dump. Now the trick is to turn that into a usuable rom, that I can flash my rom with.

What about the fine work you did for us? Are you saying that you can't load the rom dumps you made?

strange but true, I can but it still leaves something out, particularly all the stuff that was in the ext rom that auto configs the device. I am not giving up yet, it may very well turn out that I have a bad clone or bad backup file too. The quest continues.

Related

Question on using the extended ROM properly

I'm just starting to get into the depths of my PDA2K and this site is GREAT!!!!!!! Since I'm just one step up from "The Village Idiot", I have a couple questions for all you pros.
After reading about using the extended ROM, and unlocking it and seeing what's in there, I think I've figured it out. Whatever CABs are listed in the config file will be installed upon a hard reset....correct? If true, and since I have only 3.5MB left in Ex ROM, can I put the other CABs I wanted installed in say /storage/CABs, list them in the config file and upon a hard reset they will be installed? Is there any reason to put them into Extended ROM rather than Storage? Is it alright to put CABs in from like games, Resco Explorer, WebIS Mail, etc.? Lastly is there a way to set the programs up where I don't have to go back and enter all the registration numbers again?
Thanks a ton for your help!!!
Tom
In extended rom they are not taking up your precious storage space on the device.
cruisin-thru said:
In extended rom they are not taking up your precious storage space on the device.
Click to expand...
Click to collapse
is it possible then to keep the installation cabs on storage card,
and also, can that path be set in the config file in ext rom?
what happens if a particular cab is not found after hard reset?
is the installation stuck or it just gives a warning and keeps on going to the next cab listed in the list.
Have a read of this
http://forum.xda-developers.com/viewtopic.php?p=83119#83119
It might be a bit to deep but should help you along the way.
1) You can keep a cab anywere you want
2) make sure your cab is read only as it can delete itsself after install.
3) to run a auto install from a differnet storage place you need to hack the reg (see thread).
In all if you have a sd card you could leave your EXt rom empty.
Hack the reg to the new postion and run the Autorun from there.
Have fun
Thanks for all the infor everyone! From what I've read in other threads I need to make sure that TPdisabled is set to off so that when programs like WebIS Mail and SplashID get installed I can touch the screen to make sure they install into the right place and other things. Correct? If this is correct, should I just remove TPdisabled all together?
Thanks again,
Tom
TPdisabled can't be set off, its either run or not run. So dump it and you wont have a problem
MDAIIIUser - Thanks for the link! I looked at it and you're right, it's pretty indepth and I'll have to read it more closely at a later time....like at work.
Question1: leochan2005 had a follow-up saying "why not use backup"? While I agree this would be easier, I'm assuming that by using your method one would get a much "cleaner" install than backing up all the crap that was on the system prior to the hard reset...correct?
Question2: It took me a long time to get my TMo settings setup on my PDA2K and I don't want to go thru that again. Is there a way to backup those settings so that they can be auto-configured at a later time? I read about making a personalsettings.CAB but haven't done it yet.
Thanks,
Tom
MDAIIIUser said:
TPdisabled can't be set off, its either run or not run. So dump it and you wont have a problem
Click to expand...
Click to collapse
Thanks! I take it it should be at the beginning of the config file so that I can access it. Correct?
q1)
Well the short of "why not use backup" is you can if you feel that:
1) Restoring Regedit values from a lower rom version
2) Restoring system applications form a lower rom version such as BT
are called for, wanted or even needed.
I fail to see that point as a upgrade is an upgrade and a backup is a backup. Now you could do a restore of your system data also (which you could also sync and that would be clean
Q2)
Most fo those settings are part of T-mobile.cabs found in Extrom, the rest would have been reg entries that you are going to have to hunt for and copy.
So sorry no way around reading the other thread (personalsettings.CAB)
MDAIIIUser - Maybe I should state what I'm trying to accomplish and you could give me a clue as to how to do it. A couple days ago I upgraded by BT on my PDA2K (generic from Expansys) to 1.0.0.3900 (or what ever the latest is) and I'm currently looking at upgrading my radio to 1.12, but that would require a hard reset. I'm not in the mood to go thru all the program installs and SMS/MMS tweaking again, so I'm trying to figure out the best way to get all my programs and configurations back after the hard reset. I thought by incorporating the personalsettings.cab (for my Tmo settings) and your method I would be up and running pretty quickly. Yes? I have Sprite Backup, but I'm not sure if that's going to overwrite anything after the radio upgrade????
Thoughts?
Thanks!
Well my logic (that could be wrong) would say that a restore of your backup would get you to were you are now.
That you would need a restore as you have to do a hard reset after the 1.12 radion install.
But I can't answer the question will the radio be restored as well,
I don't know, I don't know the settings in the backup application, so am sorry I will have to let somebody else answer this one.

how to build custom extended ROM?

I've been debating trying my hand at cooking up my own ROM sometime here soon since I've not been entirely happy with the precooked ones. You know what they say, if you want something done right you just gotta do it yourself. ;-)
Anyways, I was thinking that I would probably like to install more software than I can put in just the ROM itself. I know I can do this through the extended ROM but I don't have the first clue where to begin and there doesn't seem to be any sort of tutorials floating around on the subject (or, indeed, of cooking in general). So how DO you create an extended ROM and add programs through it?
Avatar28 said:
I've been debating trying my hand at cooking up my own ROM sometime here soon since I've not been entirely happy with the precooked ones. You know what they say, if you want something done right you just gotta do it yourself. ;-)
Anyways, I was thinking that I would probably like to install more software than I can put in just the ROM itself. I know I can do this through the extended ROM but I don't have the first clue where to begin and there doesn't seem to be any sort of tutorials floating around on the subject (or, indeed, of cooking in general). So how DO you create an extended ROM and add programs through it?
Click to expand...
Click to collapse
There's a great kitchen that i got from the forum. I can't upload it right now, but hopefully someone has some bandwidth to get a link. Search for Wizard extended rom kitchen. I believe Faria put it together. Check out the .pdf it contains for instructions.
Basically, you'll use a tool called Winimage to "inject" files into a file called ext-rom-base.nb. In the image is a text file that tells the installer what to run.
Each file must be selected as "read only" after injecting, or it won't work.
Injecting is basically dragging and dropping cabs or exe's into the file, nothing fancy. Note that each file type is called differently, so watch out for that one.
Also - the cabs cannot require operator intervention - or the installer will hang. Make sure they run and tell you that they're done.
Then when you run nb2nbf_wizard, you can check Ext_rom, browse to the file ext-rom-base.nb, image name is Extension_ROM, and address is 9B000000.
You can create the nb.nbk to include just the extended rom, just the OS, just the Splash screens, or any combination you want.
A bit intimidating at first - but actually very easy. I never messed up my phone once working with the extended rom on the Wizard. I broke my Hermes twice already, and still can't figure it out
ftp://xda:[email protected]/Wizard/Extended_Roms/Extended_ROM_Kitchen/
Enjoy.
Post also moved to wizard upgrading.
hi guys,
I had problem when cooking ext rom. I got ''htc-wizard-ext-rom-maker-kit" by faria from ftp. I did exactly all the steps in faria pdf guide, but after hard reset it didn't work. I don't know why? Anyone help me pls.
My device:
IPL/ISL: 3.08
Radio: 2.19.11
ROM: TNT 3 Pro

Programs in ROM - vs. installing CAB's

I hope this is not too noob'ish a question:
What is the advantage of
1. installing (most of) your programs in a ROM,
vs.
2 having a rather clean/small ROM, and installing (a lot of) CABS afterwards?
I know 1. is a bit easier.
But is there any difference in performance?
I would say that you can't install anything into the ROM
That's why they use the ROM to fill it with the "cookers" special needs
The Advantage of Rom Installed Software:
You don't have to manually install it after a Hard Reset of Flash. Enough said on that, it saves you some time.
The Disadvantages of Rom Installed Software:
Uses Rom Memory for the original copy of files and Storage memory for anything that must be moved as part of initial setup. So anything that can't simply stay in Windows folder is duplicated elsewhere. For example if you prefer to have your programs in folders under the Program Files Folder then a program that uses 1mb will use 1mb of Rom memory and then when it is copied (remember you can't really delete Rom Files) it will use 1mb of Storage Memory also for a total of 2mb of used memory.
Can't uninstall original version when an upgraded version is avaliable. Sure the Rom file can be marked as deleted so they aren't listed in File Explorer anymore but they are rom files so you don't free-up any space.
More files in your Windows Folder. While the affect this has on our devices isn't 100% clear we do know that it slows opening the windows folder and I believe that it does cause a general slowdown in the device's overall functioning. This is why I prefer to have programs installed to their own folders.
The Advantages of Manually Installed Software:
Saves Rom Memory which increases Storage Memory. Basically since you have everything in Storage Memory you aren't paying extra for anything as nothing took any Rom Memory.
Can uninstall original version when an upgraded version is avaliable. Yes, since everything was installed into Storage Memory you can actually deleted the files to upgrade thus saving Memory.
Fewer files in your Windows Folder. While the affect this has on our devices isn't 100% clear we do know that it speeds-up opening the windows folder and I believe that it does affect the device's overall functioning. This is why I prefer to have programs installed to their own folders.
The Disadvantage of Manually Installed Software:
You have to manually install it after a Hard Reset of Flash. Enough said on that, it costs you some time. UC Compliant Roms can overcome this.
Well, as some cooks report: there seems to be an extra advantage of installing into ROM: everything seems to work a little smoother and faster. Don't know how or why exactly but has to do something with the after-installing process which makes the device less stabile.
Experiments have shown that of you take a full ROM vs. a lite ROM with the extra's from the full ROM installed afterwards, the full ROM is faster and more stabile.
Kyphur: I believe the second red and green titles are wrong? (I believe yoe mean Cab Installed Software?)
One of the reason that loading windows up with files slows everything down is because the are all paged & cached, depending on the settings. Once the device catches up, it's not as noticable.
Storage card Files cannot be paged like the cooked in files. That's why some programs will add .exe & .dll resources to \windows even though themajority of the files are indeed installed to the SD card.
GSLEON3 said:
Storage card Files cannot be paged like the cooked in files. That's why some programs will add .exe & .dll resources to \windows even though themajority of the files are indeed installed to the SD card.
Click to expand...
Click to collapse
I don't install to my storage card anymore. Why would I do that when I start out with over 160mb of free Storage memory?
kyphur said:
I don't install to my storage card anymore. Why would I do that when I start out with over 160mb of free Storage memory?
Click to expand...
Click to collapse
No, I don't either. But also with installing on the device there seems to be some (speed)difference in ROM installing and CAB-installing.
I'm with Kyphur on this one. The less I have in the ROM, the better because software is constantly changing, being upgraded, etc. Also, I find a lot of times my needs vary and I don't require so much "stuff" on my ROMs, so w/ the XDA-Live approach, I have the freedom to only install what I need. I guess it's a matter of preference really. Sure there are technical differences, both they are overcome either way, so it just comes down to what you like better.
pietrucci said:
Experiments have shown that of you take a full ROM vs. a lite ROM with the extra's from the full ROM installed afterwards, the full ROM is faster and more stabile.
Click to expand...
Click to collapse
Ok ... thanks!
- Do you by any chance have a link to such a benchmark?
- Does that also go for ROMs you cook yourself (with Alex' Kitchen)?
How to actually mark as deleted files in ROM?
Hello, this is an interesting thread, and I also hope you guys know more on this, since you're explaining the concept (and I also searched for a solution, but sorry, didn't find, I might have not used the proper keywords for searching):
kyphur said:
Sure the Rom file can be marked as deleted so they aren't listed in File Explorer anymore but they are rom files so you don't free-up any space.
Click to expand...
Click to collapse
So I flashed Dutty's Official WM6.1 5.2.19716 UC RTM (but which ROM it is, doesn't really matter) as my question is related to "deleting" (or at least marking as deleted) ROM files. My problem is, I want to delete \Windows\Long Send.lnk because I don't like the Comm Manager show up when holding the green Send key during a call, while I'm expecting the phone to go into speakerphone mode like used from many other phones (even my Sagem cordless at home behaves this way). The folks in this ROM's thread suggested to delete that shortcut file (which is what I think they know right if they hadn't omitted the fact that the file is in ROM), but none of the in ROM or read-only attributes can be changed with Total Commander, so I can't "delete" it. Now I understand it's supposed to be just marked as deleted as it is "in ROM", so it is supposed to survive a hard reset, but how can I mark it deleted for the time being (next ROM upgrade for example, or hard-reset)?.
pedefede said:
Ok ... thanks!
- Do you by any chance have a link to such a benchmark?
- Does that also go for ROMs you cook yourself (with Alex' Kitchen)?
Click to expand...
Click to collapse
No I don't have a benchmark of this. But then again: the current benchmarks (SPB and VS Benchmark) aren't that reliable.
I remember one cook from the Hermes device (maybe it was Pandora) made a ultra-lite version with an option to autorun everything afterwards with cabs.
This ROM wasn't as fast and snappy as the original full ROM. I think he quitted developing the ROM further.
Don't know if it's always true that everything's worse installing with cabs, it was just something a remembered from the past.
(by the way: I also install a lot from cabs...)
ChaOConnor said:
I'm with Kyphur on this one. The less I have in the ROM, the better because software is constantly changing, being upgraded, etc. Also, I find a lot of times my needs vary and I don't require so much "stuff" on my ROMs, so w/ the XDA-Live approach, I have the freedom to only install what I need. I guess it's a matter of preference really. Sure there are technical differences, both they are overcome either way, so it just comes down to what you like better.
Click to expand...
Click to collapse
the ROMs change too, and not slower than the softwares
calvinzhang said:
the ROMs change too, and not slower than the softwares
Click to expand...
Click to collapse
But flashing every week a new ROM is not for everyone. The possibility to flash once in a while is cool and good enough for lots of people, but doesn't have to become the main occupation
Zoolooc said:
But flashing every week a new ROM is not for everyone. The possibility to flash once in a while is cool and good enough for lots of people, but doesn't have to become the main occupation
Click to expand...
Click to collapse
That's what "UC" is for! Auto Install all of your apps. Just remember to keep the cab files updated.
For me, one of the biggest advantage of full rom is I save a lot of time in doing backup since the files in the rom already.
Another advantage of full rom is they don't need to store any files under \Windows\AppMgr since they can't be uninstall anyway.
To overcome the bad effects of full rom. I tend to consider the following when putting programs in my full rom.
1. File can be run under \Windows
2. Programs that don't change that often, or doesn't need the latest version.

New to Android or NAND?

I'm no longer keeping up with NAND on the vogue. So if anyone would like to keep me informed and email me or post me on any changes with NAND, ill be happy to add the news on the first post. The lock up issue with NAND has been fixed!
This is simply for any noobs or others who are having issues with Android and NAND.
IMPORTANT!!!
FOR VOGUE USERS ONLY
I am not responsible for any bricked or messed up devices. By continuing you are agreeing to my simple rule.
MY SIMPLE RULE: I owe you nothing.
I will help you through the way though if you bricked or need any sort of help.
How-to Video up NOW!!!
http://www.youtube.com/watch?v=3gTkJkOc7m4
​
First off, What is NAND?
To keep it simple...its your phones internal memory. Up untill recently we (Vogue Users) had to run Android off our SD cards using HARET. But thats another story.
What are the benefits of running from NAND? (based on what I have seen)
-Runs faster
-Longer Battery life
-faster boot up
-can be faster to put together.
-Easier to connect your vogue with android to your pc and sync
-Much more convenient.
So how do I start?
STEP1:
The Build
First you need to find a Build that is usable with NAND. Most Hero builds at this moment are not. Here are some links:
Donut 1.6
http://forum.xda-developers.com/showthread.php?t=591104
Hero
http://forum.xda-developers.com/showthread.php?t=603028
Cupcake 1.5
Method 1 from http://forum.xda-developers.com/showthread.php?t=593786
DO NOT DOWNLOAD ANYTHING JUST YET! I WILL TELL YOU WHEN A GOOD TIME WOULD BE
You may want to consider reading the rest...
STEP2:
Base Files (Most builds will supply these)
For all builds (Except the Link in Cupcake "instructions are givin in the download.) you will need a basic set of base files. The link below contains the 3 basic empty files for all builds and Systems.
http://cid-e5302e6abd554cb9.skydrive.live.com/self.aspx/XDA/Androidstuff.rar
IF
You are using Hero make sure you download hero.user.conf too:
http://cid-e5302e6abd554cb9.skydrive.live.com/self.aspx/XDA/hero.user.conf
-create a new folder called conf
-and place hero.user.conf in your new folder.
STEP3:
Rootfs
After you have the Base files you will need a rootfs. Depending on your Build, you may need a different type then the one I am going to supply you. Most builds will supply you with one. This one is DZO's rootfs.
http://cid-e5302e6abd554cb9.skydrive.live.com/self.aspx/XDA/rootfs.img
STEP4:
Prepare
-You need to clean out your storage on your SD. Make sure you delete everything.
-Create a file called android on your desktop.
-Download the base files, unzip, open folder, and place all 3 in your android folder
-Download the rootfs and place them in your android folder. Make sure you either download DZO's or the one your Build provides.
-Download a System.img. When you download a System most likely it will have a different name such as system-hero-123.img. You need to rename it system. So it should look like system.img . Then place it in your android folder.
-If you are using Hero place your conf folder in your android folder.
-Depending on your Build (mostly Hero) you may also need a Data file. The build you select should supply one. Download it and place it in your Android Folder
STEP5
Placing
Open up your android folder of all your collected files and select all, copy, and paste into your empty SD card.
STEP6
Unlocking
If you have never flashed a ROM before than you don't have HardSPL installed. So unlock your phone with...
http://forum.ppcgeeks.com/showthread.php?t=20370
Make sure you follow the forums directions.
STEP7
Method
Method1: The way I do it.
Download ROMUpdateUtility.rar
http://cid-e5302e6abd554cb9.skydrive.live.com/self.aspx/XDA/ROMUpdateUtility.rar
Extract to a newfolder
Download a kernel with your screen size
http://it029000.massey.ac.nz/vogue/files/?C=M;O=D
Don't know your screen size...check this out
http://forum.xda-developers.com/showthread.php?t=544906
After you have have gotten the kernel:
rename it to RUU_signed and place it in the ROMUpdateUtility folder you created.
NOW you need to plug your phone into your computer. Establish active sync. And run ROMUpdateUtility.
-Follow the Instructions on the screen.
Method 2 and 3 can be found here:
http://forum.xda-developers.com/showthread.php?t=593786
This also shows my method...but a little less detail. You can also find many other helpful things there.
If you fail OR think your bricked your phone.
You will need to download one of these depending on your carrier...Make sure you download the shipped gps rom. (If you are Verizon skip down)
http://forum.ppcgeeks.com/showthread.php?p=191607
Than you will put your phone in boot mode. Hold the Camera and Power button. While holding both of them...get a pen or something small and hit the little restart button on the bottom of your phone. You may have to hold it for like a second.
-you will see three color bars on your phone
-plug your phone into your computer
-run the backup
After your phone is all back to normal. Make sure you run internet explore on your phone. It will enable you to get data.
For Verizon follow the instructions here.
http://wiki.ppchaven.com/index.php?title=Pocket_PC_WIki:FIX_VERIZON_GPS
That is about it. I'm sure I forgot some stuff and will add on to this. Make sure you donate to the Devs for all their hard work.
DZO
http://forum.xda-developers.com/showthread.php?t=593786
jamezelle
http://forum.xda-developers.com/showthread.php?t=603028
plemen
http://forum.xda-developers.com/showthread.php?t=591104
vilord
http://forum.xda-developers.com/showthread.php?t=523692
They deserve it.
thank you this was very helpful
inphin1ty said:
thank you this was very helpful
Click to expand...
Click to collapse
No problem...
yea here is the md5sum: 9b08971e7f23619b6a9a4db9d52d857a
jamezelle said:
yea here is the md5sum: 9b08971e7f23619b6a9a4db9d52d857a
Click to expand...
Click to collapse
Whats that?
staud8469 said:
What are the benefits of running from NAND? (based on what I have seen)
1 Runs faster
2 Longer Battery life
3 faster boot up
4 can be faster to put together.
5 Easier to connect your vogue with android to your pc and sync
6 Much more convenient.
Click to expand...
Click to collapse
great thread. I've run both from nand and sdcard. i have not messed with ext2 on the sdcard.
I agree with 3 for sure. I would also add that there is a deep gratification in wiping win mo off the sdcard
6 is debatable, depends on which conveniences you want. changing lcd.density, changing resolution are all much faster running from the sdcard - no flashing or messing with build.prop, just edit default.txt and reboot (aside - if you have a non-sdhc card you can flash on the fly from the sdcard, but changing lcd.density still requires pulling and pushing files from the system, which is not as easy as changing the default.txt). also more convenient to back-up or revert to a data.img when running from sdcard. definitely booting straight into android is convenient, as is the new mass storage on boot method, as well as having a re-writable system (which you also have using ext2).
1 and 2, I honestly have not noted a significant difference in battery life. With a fast sdcard, I don't think there is a significant difference in speed either - dzo has said this in one of the non-vogue forums as well. i have not tried any sense builds from the sdcard though, and that's where you would notice the greatest difference in speed if there is any.
4 I agree with in general.
I think running from the nand is a huge advance, and great for everyone to try. but, running from the sdcard is still a decent way to use android. choosing between the two comes down to choosing which conveniences suit your usage style the most.
One last thing - please add vilord to your donate links (his google ion on vogue thread), he has been instrumental in developing the ril and advancing android on the vogue. srwalter also deserves mention for his reverse engineering of the libgps.so to bring gps first to cupcake and now to donut as well. jamezelle, plemen, mssmison, zenulator, enatefox, f00bar (no specific order) have all worked hard porting roms and working on things like compcache, swap, modem, etc, which has all been invaluable (zenulator and mssmison deserve special credit for spearheading the porting business). however the gruntwork of porting to the vogue has been done mainly by dzo who brought us the kernel and initial ril and now nand (he's just frickin amazing, he singlehandedly got the first functioning port to the vogue and others helped from there), then vilord who took the ril and really refined it. I guess suffice to say, there have been a lot of people involved along the way, thanks to all of them.
when i try to run android from both nand and haret i always get an error about not being able to mount sd card. does this mean i need to reformat the card? if so how do i do this?
Barogi44 said:
when i try to run android from both nand and haret i always get an error about not being able to mount sd card. does this mean i need to reformat the card? if so how do i do this?
Click to expand...
Click to collapse
When do you get this error? During linux kernel bootup?
Verizon users.
I just update a fix for Verizon users. Shows you how to get GPS too!
Also...there will be a video up soon. It seems that there are so many people having issues. So I will create a video from start to finish. Will be posted up late tonight/ tomorrow morning.
staud8469 said:
When do you get this error? During linux kernel bootup?
Click to expand...
Click to collapse
Yea.. i think i may need a new sd card. Can android boot from a 4gb card or is 2 the max?
Barogi44 said:
Yea.. i think i may need a new sd card. Can android boot from a 4gb card or is 2 the max?
Click to expand...
Click to collapse
i running with a 8gig PNY sdcard
it could theoretically run off of a 512, but you would be a little cramped on space
i guess android doesnt like some of them
so really it doesn't matter how big the card is? do they all have to be formatted to fat32?
Barogi44 said:
so really it doesn't matter how big the card is? do they all have to be formatted to fat32?
Click to expand...
Click to collapse
short answer, yes.
Hey guys...I will try my best to get that video up today. I am about to start recording it.
Am I correct in assuming that step 4-b is create a FOLDER name android on the desktop?
Can I delete those files from the SD when flashing is done?
THANK YOU for the N00B instruction, works great.
stopthebus said:
Am I correct in assuming that step 4-b is create a FOLDER name android on the desktop?
Can I delete those files from the SD when flashing is done?
THANK YOU for the N00B instruction, works great.
Click to expand...
Click to collapse
Yes that is correct, as for deleting the files...I would assume you could. But im not sure. Maybe they are still needed on boot. Never hurts to try though.
im not getting access to the internet after i flashed, am i suppose to edit anything?
im running the donut flash on my sprint vogue.
gigermunit said:
im not getting access to the internet after i flashed, am i suppose to edit anything?
im running the donut flash on my sprint vogue.
Click to expand...
Click to collapse
Wait...NVM you want data to work right?
If you are using donut...try to restart your phone one time. After it boots back up you should see a 3g symbol appear on the notification bar.
If that does not work...go to your apps and open modem. Click once on disconnect and then once more. Then click connect.
Tell me if that works...

[Q] Issues with TD2 T5388i

Hello
After a couple of days of hunting a new update for my new phone, I got to a dead end.
After trying multiple ways (most of them are from here so I will post only 2-3 links): http://forum.xda-developers.com/showthread.php?t=732362 , http://forum.xda-developers.com/showpost.php?p=3695364&postcount=4 , http://forum.xda-developers.com/showthread.php?t=416211 , the problem was the same. After sync and starting installation via USB (phone freezes) and SDcard (phone freezes automatically with starting Heret.exe) I don't know and really can't find a way how to remove WM6.5 (and put android) or someway update or install a fresh version.
I hope someone will be willing and able to help me with this problem.
Thanks in advance.
Dude, what *exactly* is your issue? From what I can see, you're trying to install android and it's not working for you..
Either way, first, format your SD before trying anything. See if that will get your phone to respond. If not, get a new one. The problem with SD cards is, when they fail (or get corrupted), it can cause your phone to "almost freeze". Instantly fixed by removing the SD. And booting the phone without it usually allows the phone to work normally.
The SD is brand new (4GB), and I also tried with 5 other SD cards (2 and 4 GB's).
I don't think it's to the SD card's, its more to the damn phone and I have no clue how to reinstall WM or put Android on it. And that the issue, how to prevent completely freezing while sync via USB and boot from SD card.
Hope you understand better now neocyke
Well, honestly dude, a T5388 is not exactly a TD2, so, what would work on an actual TD2 might not for you. Based on my experiences with clones, best is to flash with no SD in. Try visiting this thread and use the ROM there. Get the IDT flasher and work your way from there. Oh, and you might wanna remove Activesync or WM Device center before flashing.. Good luck with that..
As for android, installation for XDAndroid is the simplest thing in the world. Just unzip the FRX06 zip file to a folder (andboot is usually used). Take the topaz startup and put in the root of that folder (remember to edit as needed). Then copy *the entire folder* and dump it on the root of your SD. Run Haret from WM and that's it. Just wait for it to boot.. But then, this is assuming that your phone is supported by XDAndroid of course. You might wanna check that in the android dev section..

Categories

Resources