I can't seem to connect my Bluetooth GPS reciever to my BA with WM5 on, I can pair the device, but thats about it. Tomtom 5 can't see it and I can't see any way of manually connecting it to the GPS device?
Any ideas ?
Have you looked at my piece in the WM5 Wiki?
Mastiff said:
Have you looked at my piece in the WM5 Wiki?
Click to expand...
Click to collapse
Took a bit of finding but I followed instructions, installed Tomtom, paired the GPS, set the COM ports.
When I went into Tomtom setup the port (Com 7) was not in the list of available ports.
I have BT UART, COM2: Serial Cable on COM1: COM9: Ir on COM 3
but no COM 7, any ideas ??
This has been reported on a few PPCs here. I know somebody made a very small app that makes available the port you want to. You may try to search for that.
Does anyone know what this small app is called??
Related
Hi,
Just wondering if anyone has successfully hooked up a Garmin E-Trex to an XDA. It should be possible using the serial connector from both (null-modem!?!). If so what software was being used on the XDA.
Cheers
Jeff
Garmin eTrex - XDA
The eTrex and XDA make a great combination even with Pocket Streets: the eTrex gives you the vector to your destination and the XDA shows you where you are on the map at zilch cost. The draw back is that you can find your target destination on PStreets but there doesn't seem to be a way of extracting the coordinates to feed into your eTrex.
So I got the TomTom Citymap of London to try that out and after a poor user experience when the supplied gps driver locked the XDA up and I had to download another, plus no explanations of various 2.06 driver features plus finding that parts of the M25 London orbital were chopped off, I have the best of both worlds. It only cost me 10UKP.
Oh yes, connections. You can buy a TomTom power/gps cable for the XDA that is meant to take the TomTom gps mouse via a 4 connector phone type socket. So all you have to do is come up with a 4 connector phone type plug leading off to you eTrex. If you have the eTrex car cable for power and RS232, which you might want to use with a laptop, you will not want to cut this. So get a cheap RS232 cable and chop the appropriate end off for your phone type connection. Marry everything up, ignore the wife's complaints about wires and delayed departures while you fiddle with the eTrex and XDA, and you are off.
The TomTom cable phone socket housing can be taken apart briefly to check which are the Common, TX and Rx wires, and the tiny circuit board even tells you which is which. If you want I can give you the pin outs but at the risk of misinterpretation.
Etrex GPS
Managed to get it to work with Navigator and am well impressed.
Got a cable from http://pc-mobile.net/gps.htm. However had a few problems to start off with. The XDA ground to a halt (I have updated the ROM to the latest O2 release and apprently TomTom 1.4 has a problem with later version). Updated TomTom to 1.51 and still no joy. Change the interface from Garmin to IMEA 4800 baud on both GPS and TomTom and had a great weekend driving up and down the motorway and country roads in Derbyshire.
Jeff
Jeff,
Cool, isn't it! Perhaps you can enlighten me about Navigator. Not knowing much about TomTom I rather expected voice prompts on the citymap thingy I downloaded. Question: what do you have to do to get the voice prompts invoked (spend more money probably) and can you hear them from the XDA? :?:
Ken
Navigator Talking
I have Navigator 1.51 installed (downloaded from Tom Tom site) only you need at least a previous version as otherwise there are no maps.
When you do a route plan (rather than just have it in map mode), it does the "300 yards turn right......turn right.....find the next convenient place and turn round"
Not sure what happens with previous versions as I had 1.4ish on before and that interfered with Windows as I had upgraded PPC2002 to a newer version and it odesn't like that too well.
Cheers
Jeff
Hi guys, do you know if the connector for the Garmin Geko 201 is the same as the Etrex? I was looking at buying the Geko and the cable from the site listed above but they don't say specifically for the Geko. I put an email question in to the cable guys but you never know how long it will take to get an answer. It's definitely a flat connector and not a round pin type. Thanks - Jim
Hi,
I've bought a Fortuna U2 GPS receiver with an O2 XDA lead.
I've downloaded some software (GPSeasyCE), but when I try and connect to the GPS unit, I get "unable to open COM1".
Any suggestoins please?
I have tuned my keyboard driver to IR & serial, and I think I'm using the correct com port settings (4800bps, NMEA 0183).
I'd really like to just check that the hardware is working.
Can I download some free demo software that will do that?
What's best?
Thanks in advance, for any help anyone can offer,
Muddy
You have to turn off the IR port.
Muddy said:
Hi,
I've bought a Fortuna U2 GPS receiver with an O2 XDA lead.
I've downloaded some software (GPSeasyCE), but when I try and connect to the GPS unit, I get "unable to open COM1".
Any suggestoins please?
I have tuned my keyboard driver to IR & serial, and I think I'm using the correct com port settings (4800bps, NMEA 0183).
I'd really like to just check that the hardware is working.
Can I download some free demo software that will do that?
What's best?
Thanks in advance, for any help anyone can offer,
Muddy
Click to expand...
Click to collapse
disable your infra red port under setting, connections/beam, it will then work. A point about cables to work with gps, if you get a serial xda cable, and you also have a pc serial cable that links to your gps, all you need to do is get a 9 pin male to 9 pin male null modem adaptor, or make one, you need to join pin 2 on one to pin 3 on the other, pin 3 to pin 2 and pin 5 to pin 5, plug your xda lead one end, gps lead the other, and away you go.
I have recently "upgraded" from xdaII to xdaIIs and I'm having a few problems. I have upgraded the BT stack to 3500 but I still can seem to connect to my tomtom gps. Device sees it but tomtom 3 cant. I'm completely confused by the connection wizard- none of the profiles seems to fit gps. I also dont seem to be able to send or receive files from my old xdaII. What am I doing wrong?
I'm also a little confused about roms. Do I need to upgrade my rom? Is there a simple way avoiding anything too technical (I've read about "country codes" and other wierd stuff). My current config is:
ROM: 1.12.62
Radio: 1.02.00
Protocol: 1337.32
ExtROM: 1.12.178
Could someone please help! I only have a few days to decide if I want to keep it or stick with my xdaII...
Gps's use the serial profile to transmit the data over - its like a virtual serial connection - so you need to tell tomtom to look on a com port AFAIK,.
For eample in my Tomtom list of connections there is one called 'BT on Com6, ' which is the bluetooth comport on my unit.
But there are also listed more com ports...
Com5
Com4
Bluetooth Serial port Com7
The XDA only actually has 1 com port (com1) so any other are virtual ports created by various software, you just need to find out which one is the one for the GPS...
So in "tomtom gps v3.07" I go to the gps tab and by default its set to infrared port. I change to "BT on com6" and click OK. When I restart the program it always resets to "infrared port" even if I try a different port. Really am stuck- never had any problems with my xdaII- just put in BT port and it picked it up automatically...
The problem is it's not always the same com port for different devices - firstly does your unit have the widcoom stack version of are you on the microsoft stack..
Whichever you have you need to find where the BT com port is configured..
On my widcomm i go to 'bluetooth setting' ; 'services' ; "serial port'; 'advanced'
in there it says...
inbound com port : 6
outbound com port : 7
so the incoming com port on my bluetooth is 6 hence the 'BT com port on 6' listed in my tomtom gps.
so you need to find your BLuetooth com port and find out which com port number it is set to. Not sure as to why tomtom gps does not save your settings, the only thing I can think of is becuase it never gets a valid signal from the comport select, and does not save the change unless it does.
Also: I assume the gps unti has a pairing with your XDA unit?
So does the widcom stack work on the xdaIIs? If so where can get it?
Sorry: I cannot be certiain the widcomm works with the IIs, but is can be downloaded from this site if you are willling to try, just do a search oin widcoom, and you will find a lot of entries...
For the MS BT stack; look under start, settings,System tab. There is a icon labeleld Bluetooth settings in there you can see/set the com ports for the bluetooth link. they also need to be enabled witch a check box before they will work...
So on "bluetooth seetings" serial port/advanced I have inbound COM port 5 and Outbound COM port 6. Below it says "Default device for outgoing serial connections: TomTom Wireless GPS. Display the device selection screen the next time an outgoing serial connection is attempted" next to a ticked box. I have tried bt com 5 and 6 in the gps settings and it wont save or recognise either. I can, however, pair and connect to the device in my BT manager but Tomtom doesnt recognise it...
Hmmm - all sound ok to me but I currently use a wired GPS, so I have not actually done it. I'm afraid I'm as stuk as you are now...
Sorry bro- I have sorted this now. Thanks...
For me, I just selected Comm 5 from the GPS status drop down and it works like magic!
I've recently purchased an EverMore GM-R900 GPS receiver, connected to the 750v serial port through a mini-DIN adapter (which also includes power input from the car adapter). The question is : how do I map the serial (data) to make it available to other apps (other than active sync, which seems to be the only user of the serial...) ? I tried with GPS Gate but unsuccessfully, I cant find the correct source. Has anybody experienced something similar, yet? Perhaps with some carholder with integrated gps?
UP! C'mon.....is there a way? I've also tried with gpsgate but maybe I'm using the wrong parameters....... I've tried (from WM gps config) to map every port but I'm not getting a thing on any of them. The antenna itself seems to be working.
Still No GPS Device Found
Hi Guys,
Thanks in advance, i have gone through this site numerous times but still haven't been able to get my TomTom working on my new Treo750 and Ox-XDA IIs both running WM6.
I have GPS receiver in my cradle which works like a jam on my previous Treo650 (Running PalmOS). But since upgrading to this WM device it has become a night mare can't get it right particularly the way windows is handling com ports.
Can any one please guide me on how to get it going as I don't have PDA with in-build GPS receiver nor bluetooth receiver only this serial connected receiver.
Thanks
Nilesh
not sure i understood
If you have the tom tom software from your 650 and you are trying to use it on wm6 ,it is more than liely a software problem.
i have tom tom running on my 750,with a sirfstar 3 bluetooth gps unit, with no problems but the software came with the device.
If I am not mistaken tom tom allow you a device change every so often, in which case you will be able to download the correct software for your device.
i have tom tom 6.000 and gps driver v1.20 but its show GPS signal not found or no gps signal in my spv 1000 can any one help me how it will work in c_shekhar"s Rom
tomtom
Hello you must make a com 5 for it to work and then go to tomtom and give it in by the gps settings.
hello
can you explain me more please ?how to do it ?
This is from the wiki, so in future, have a look at it first. I say this because your problem could have been solved much earlier had you read it. It will save you time. If you can't find answers there though, then please do come and ask us.
Tom Tom 6/Garmin/GPS Software seems to restart my Himalaya when looking for my external bluetooth connection?
Pair your bluetooth GPS device with your Himalaya first. After this, make sure to choose the advanced option which will give you the choice of choosing the serial connection and then which port you want to use. I always choose Com 5 as this seems to work fastest, most stable etc. After this, you then leave bluetooth on and in discoverable mode. After this, load up your software. The correct com port should then appear in the list of possible com ports for you to choose from (Com 5). After that, all should be well with the world. The reset seems to be caused when your Himalaya looks for an external bluetooth GPS device on the incorrect com port.
Hi,
I'm trying to get GPS2Blue to work and managed to get a connection between my Kaiser and my desktop (with a dongle using the Toshiba Bluetooth stack) by creating an outgoing port on the Kaiser (start-settings-connections-bluetooth-com ports-new outgoing port-DESKTOP-next).
I am successfully paired with a Lenovo T61 using the internal bluetooth with a broadcom stack (Vista Bunsiness x64), but while the Desktop advertises 'Serial Port' and 'ActiveSync' as bluetooth services, the T61 stack only advertises 'ActiveSync' 'Wireless Stereo' and 'Headset'. As a result, I can't add an outgoing port to the laptop and GPS2Blue doesn't work.
Does anyone know how to tell the broadcom stack to tell the kaiser that it has SPP (Serial Port Profile) available for it? Using GPS2Blue over TCP/IP is not an option because the virtual com port driver currently doesn't support Vista x64.
This has been bugging me for a loooong time, I'd really appreciate any help with this. Thanks!
Lncdoc
OK, 2 things.
Firstly, GPS2Blue doesn't need an Outgoing port on the Kaiser, but an Incoming one. Then, you discover services on the phone, from the PC, and you'll have a serial port you should connect to. Not the other way around like you were saying. Now, WM6/6.1 don't let the user set an incoming port from the BT configuration page anymore, so a manual registry edit is necessary. Attached is a .reg file that will set an incoming port on COM6.
Apply this, soft reset. Then run GPS2Blue, set it to use COM6, discover services from the PC, connect to the serial port, and connect to whatever serial port the stack maps it on the PC with your GPS program.
Secondly (but now unrelated!), if from the phone you'd like to see a serial port on the PC, there are 2 solutions. Firstly look for an "add new seral port" option in your BT stack on the PC, some support multiple ones.
If there's none, you should open activesync connection page, disable serial connection. On the Phone the Arcivesync entry will now revert to serial port. To have AS again, reenable the COM port connection in AS.
Thanks a lot! That worked like a charm. After Vista with the Broadcom stack forced the use of COM9, I changed it manually to COM5 in the device manager (For reference of other people wanting to do this: Device Manager / Ports (COM & LPT) / Standard Serial over Bluetooth link (COMn) / Right Click / Properties / Port Settings / Advanced / COM Port Number), since some software (like MeHere) only supports up to COM8.
Now everything works like a charm on my laptop.
Note that this weirdly enough also works with an Outgoing port on the Kaiser if you have a stack (on your PC) which broadcasts the availability of an incoming serial port (in which case the Kaiser initiates the connection, not the PC, and the COM Port sends regardless of whether something is connected or not...). Not that I'm recommending this route to anyone, but I got this working on the Toshiba stack.
Anyway, thanks a lot again, it's finally working perfectly with OziExplorer, MeHere, Google Earth.... you name it.
Lncdoc
Arrrrgggg! I am so close. The incoming BT port bit helped me to get connected but, although GPS2Blue is gettting a lock, and I appear to be connected to EarthBridge/PC, the GPS data doesn't appear to be transmitted to Earthbridge/PC. Google Earth keeps putting me off the coast of Africa instead of south Florida.
I'm about ready to go pickup a copy of Streets & Trips with GPS.
GPS2Blue 1.9
I allready got .reg file on my computer.
The only thing i don't understand is how to get the incomming port on my laptop....
Greetz
Peter
Loaded the appropriate reg values...nothing. Still doesn't work. I can't see the port on the PC or Handheld under "Bluetooth Services".
Thanks kilrah
Your solutions works great for me and i have tested this with my i900 and two different notebooks running Windows 7 and Windows XP
Works in both notebooks
I was using Garmin Mobile PC Version 5
Thanks again for your great help
thx kilrah
'elpetah1984' you must import registry value to PDA windows not PC
http://forum.xda-developers.com/showthread.php?p=8429209#post8429209
F I N A L L Y !!!!!!!
I've finally managed to do it!!! Oh man.. what a fight! almost 4 am and trying since days.. eheheh it is really rewarding! Will be doing a tutorial to avoid hours and hours of frustation to anyone trying this!
iRiKi said:
F I N A L L Y !!!!!!!
I've finally managed to do it!!! Oh man.. what a fight! almost 4 am and trying since days.. eheheh it is really rewarding! Will be doing a tutorial to avoid hours and hours of frustation to anyone trying this!
Click to expand...
Click to collapse
That'd be great!
Did you get it to work with many apps? I remember one time I managed to get it set (don't know how, can't reproduce my semi-success) so I could share the ActiveSync port and in Windows I could open the COM port on PuTTY to see the NEMA output but only a couple apps recognized that there was a GPS there -- the main thing I wanted to work (inSSIDer) couldn't see any GPS.
I'd definately be interested if you came up with a reliable way to make it work.
mmiller7 said:
-- the main thing I wanted to work (inSSIDer) couldn't see any GPS.
Click to expand...
Click to collapse
I saw your post @ metageek forums, because I too am unable to make it work with either version of inSSIDer, although Netstumbler saw it nice and easy. Thing is: I have Vista, and Netstumbler doesn't like Vista like me
I'm gonna get a XP lappy tomorrow which battery only works for half an hour but hey, it's a start
iRiKi said:
I saw your post @ metageek forums, because I too am unable to make it work with either version of inSSIDer, although Netstumbler saw it nice and easy. Thing is: I have Vista, and Netstumbler doesn't like Vista like me
I'm gonna get a XP lappy tomorrow which battery only works for half an hour but hey, it's a start
Click to expand...
Click to collapse
Good luck, XP is out of the question for me because HP doesn't provide Bluetooth drivers back to before Vista. Maybe I can find a way to forward the COM port and a USB WiFi adapter through VirtualBox and use XP that way...though I've been unsuccessful with either of those so far.
Actually you can forward the USB device to Oracle's Virtualbox, I have my TP-Lnk USB WiFi forwarding into a linux virtual machine working perfectly in monitor mode with kismet and aircrack I don't think you can forward COM ports tho, but if you have an external USB bluetooth adapter you can also forward it into XP!! Will try that asap!
Thing is, I wanted to use the onboard wireless because it's way more sensitive than the external USB adapter, but it's not possible to forward it inside a virtualbox.
Ahhh computer issues.. always bugging me since 1993 XD
iRiKi said:
Actually you can forward the USB device to Oracle's Virtualbox, I have my TP-Lnk USB WiFi forwarding into a linux virtual machine working perfectly in monitor mode with kismet and aircrack
Click to expand...
Click to collapse
I got bad news and good news.
Bad news:
The USB forwarding of my wireless card works under Linux but FAILS under a XP VM!!! %$#*@#!"#
Good news:
Downloaded Franson GpsGate trial and now inSSIDer is working !!!!