hallo,
I have a question about wifi under wm5.
I am trying to access 2 different networks, one at home one in the office.
the networks are set up as follows:
OFFICE
mac address filter, wpa, no ESSID
HOME
mac address filter, wep 256 bit, no ESSID
I added into both routers the mac addr of my device (thanks to vxconfig)
on my imate, in the wireless settings page, LEAP tab, I added 2 settings, one for home and one for the office.
I noticed that I'm unable to manually type in the WEP key, while I can do this at home.
As you might imagine, I'm unable to connect to either network, though I don't get any particular error message. I simply don't connect; the router's log doesn't show any kind of access.
Both networks work fine, naturally. my device works fine too, as I'm able to connect to public hotspots.
I seem to remember, but I'm not sure (hence my question), that wifi under wm5 only accepts 128 bit keys...
might this be the problem? or am I doing something else wrong?
also, is there a program that allows me to manually set the WEP key under wm5, or a program that gives greater control over wifi?
thanks!
ok, update: I don't understand how, but when I clicked on the tools button in the wireless manager page, and then on Network cards, instead of the usual network cards page there was this page in which I could insert the wep open key, etc.
I clicked on OK, then tried it again and voilà, the page has disapepared again and there is the usuale network cards page.
where has it gone??? I don't get it honestly.
Related
I'm currently running wm5 ivan w/rd
i keep having this problem where i try to connect to a network, and it connects, but i can't do anything.
When i open up my ipconfig it shows the network ip address as 169.254.x.x where x is always something different. My router shows the mac address on the network but it's unreachable.
Does anyone have any idea where this ip is coming from? I've tried different radio versions, and it happens so far with 1.1.13 and 1.1.15 on both wm5 AND wm3.
169.254.xxx.xxx is a class of ip addresses set automatically to a device, when this can't connect the dhcp server. is a reserved network.
if your router is set as dhcp server, you must verify the link connection with pda. else you must configure the correct ip address manually to the pda.
download and run vxIPconfig and use that to release and renew a new IP from the DHCP server
Nine times out of ten this is caused by bad encryption settings. If you put in the wrong WEP key for example this is what you would see. You don't get error messages when it's wrong, which is kind-of by design and desirable for security reasons.
I'm downloading vxipconfig right now. I did a search last night and was reminded of 169.254.x.x coming up on machines when winsock is corrupt.
Another web site said something about how a pda will connect to the first computer with activesync through wifi under this ip address and try to sync, and then it will get a normal ip address. I don't know if this is true with this device.
@closer what do you mean verify the link connection? The router shows the pda's ip address in it's connection manager, but for any computer or pda i don't know a way to "verify the link" other than look at it. There's no command for this. The router is set up to correctly assign dhcp as i have 2 computers and 2 xbox's connected through lines, and 2 computers through wifi. I know i can manualy set the ip, which i often do for everything but the laptop, but this is a pain in the ass to try and find out the gateway of every single router when i'm out in town. That's a workaround, not a fix.
@Black6spdz I was using Myipconfig and it would release and renew to just a different 169.254.x.x. I'm going to try vxipconfig when this happens again.
--Well, last night i got pissed and abandoned working on it. Low and behold when i wake up today it's working fine and has the correct ip address. That sucks, because now i have no idea what was wrong.
so...
-It's time to go connect to some other networks and see if it resolves correctly.
-Then i'm going to go through the 3 different radio versions and see how they affect it.
when I had that problem it was because my settings were set up incorrectly.. If i were to use gprs, it'd work fine. But wifi would not. So i had to make a seperate setting with generic entries and not set up proxies. then wifi would work. sort of a pain. but it would work...
I have had my wing for just a few days, so I am still learning what it can do.
I can easily connect to my home wireless router and have a strong signal. When I open IE, the wing starts loading a GPRS signal and then I get a default page with a tmobile splash and a search box. When I try to enter www.google.com it just sits there.
I dont think something is correct. I want to browse the internet directly with IE on the wing with my wifi.
I do not have a internet or data plan of any kind.
It does have WM6.
Any ideas?
Are you sure that you've achieved a connection with your router?
Go into your WIFI settings, and make sure you have acquired an IP address... the little antenna icon may show up at the top, but you may not be fully connected.
In WIFI settings, configure says i'm connected.
In network adapters, SDIO Wlan shows "use server assigned address" checked,
and it has a IP address in it.
Am I in the right place?
Just spent some time with tech support on a landline. Fixed the problem in a wifi configuration menu. Changed it from "work" to "internet".
Done.
I can stop beating my head on the wall now.
Hi.
I recently bought my s730. Quite pleased with it, but one thing bothers me.
When i connect to my wlan at home (zyxel_2602hw_d1a WPA-PSK TKIP) i'm able to connect to the router, but I don't seem to be able to get an connection to anywhere outside my own network. I tried using Live Messenger, IE, Opera and Skype, but nothing happens.
When I'm using GPRS or EDGE it all works smoothly.
Any suggestions?
Do you have your connection set to automatic or only through your phone network? I have seen a few problems with that.
Also, double check that you are entering wep or any other security protocol correctly, took my 6 tries before it would work, it looked like it was connected to the network but it really wasnt (just personal experience with this phone.)
10332007 said:
Do you have your connection set to automatic or only through your phone network? I have seen a few problems with that.
Also, double check that you are entering wep or any other security protocol correctly, took my 6 tries before it would work, it looked like it was connected to the network but it really wasnt (just personal experience with this phone.)
Click to expand...
Click to collapse
I do have the connection settings in both IE and Opera set to automatic. I's there somewhere else I have to change settings?
I'm quite sure i typed the password correctly. I also checked the client list on the router and the phone showed up correctly.
Gah, cant remember where I saw it but there was a setting in the phone itself for what to connect to.
Another thing to try under the wifi connection open your saved connection and go into it and see if you have it set to connect to the internet or just to the private network under "network type" in the Wi-Fi sub menu of Wlan settings. Its late and I cant think right, i'll see about checking more into it later...
I solved this problem - change your WLAN security on your WLAN router only on exactly MAC adressee (no any WEP) and your Wings is allowed to connect and all will be OK, work OK - Skype, IE, Opera. Problem was only to find MAC adressee my Wings
Wing + WRT54GL
Hi!
I have an S730 and a Linksys WRT54GL router. I've tried to use wlan with my phone, but it doesn't working. I want to use WPA2 with AES without Radius. Is the WPA shared key (router) same to network key(phone)? without security and encryption, it's working well.. I cannot see any syslog. That could be so easy..
klenovcok said:
I solved this problem - change your WLAN security on your WLAN router only on exactly MAC adressee (no any WEP) and your Wings is allowed to connect and all will be OK, work OK - Skype, IE, Opera. Problem was only to find MAC adressee my Wings
Click to expand...
Click to collapse
I tried removing security for my phone MAC address, but there dosn't seem to be any options on my router allowing this. So I'm still stuck;-/
ksga said:
Hi.
I recently bought my s730. Quite pleased with it, but one thing bothers me.
When i connect to my wlan at home (zyxel_2602hw_d1a WPA-PSK TKIP) i'm able to connect to the router, but I don't seem to be able to get an connection to anywhere outside my own network. I tried using Live Messenger, IE, Opera and Skype, but nothing happens.
When I'm using GPRS or EDGE it all works smoothly.
Any suggestions?
Click to expand...
Click to collapse
Did you check network settings? I mean e.g. if you don't use DHCP server and you didn't fill in right settings phone may connect to network but may not get outside. I know it can look like "lame" question, but sometimes even a master can do a newbie mistake..
ksga said:
I tried removing security for my phone MAC address, but there dosn't seem to be any options on my router allowing this. So I'm still stuck;-/
Click to expand...
Click to collapse
usually it is in section WLAN Advanced setup - WEP Encryption - disable and in WLAN MAC Filters - active + allow asotiation with table of adress your Wings - aply . I have Zyxel Prestige 660HW.
I'm sure that DHCP is active, and that I get an IP.
I tried disabling security on my router, but same problem. Connects to my router, gets an IP but still nothing works
ksga said:
I'm sure that DHCP is active, and that I get an IP.
I tried disabling security on my router, but same problem. Connects to my router, gets an IP but still nothing works
Click to expand...
Click to collapse
Your DNS are also provided automatically? Or could you ping (through some app) to any IP address of any server on the internet? If you succee, then we can look for a mistake with DNS.
Problem solved!!!
Okay. Found the cause for all my sufferings...
Power management. under WLAN-settings i changed power setting from power save mode to best performance...
thanks for all the help. hope next time I have a better question
wifi problem
hello everybody,i have tried several times to connect to my router at home but no chance at the end i got this warning saying:
cannot log on to the wireless network this network requires a personel certificate to positively identify you.
Help!
I have a Netgear DG834T router as provided by Sky. I have one wired and two wireless connections running into it (let's call them WD, WL1 and WL2 respectively).
On the connections page I can see all of them under "attached devices"...but now I want to connect using my Kaiser (actually an O2 XDA Stellar)
What happens...
On the Kaiser, I get an IP address (assigned by DHCP) as normal - but can't access the internet - or at least, can only access it very rarely - http://www.google.com can't be found, but http://www.bbc.co.uk can. No idea why.
On the router, under "attached devices", not only can I NOT see the Kaiser, but WL1 and WL2 also disappear. WD remains visible. The router cannot ping the IP address of the Kaiser (timed out). If I disable WiFi on the Kaiser, then WL1 and WL2 are immediately visible again. Internet connection on WL1 and WL2 works, even when they are not visible.
I HAVE connected to this network before without any problems.
What the hooting heck is going on, and how do I fix it?
Thanks!
Time to troubleshoot! What happens with this phone on another wireless network. We need to determine if it's the phone or the network. Do you have any friends with a phone like this? Can you use their phone on your network? Do you have any ROMs flashed, has this phone ever been on the network without problems?
If the phone works on another router try looking for firmware updates for the router. Those things really do need to be updated often and it could have something to do with that.
Only have access to one network :-(. Might be a couple of weeks before I can access a hotel one or something like that.
Think next door neighbour has similar phone, but different provider...will try if he'll let me!
No ROMS flashed.
It connected fine when I first had it. As far as I know, I've changed nothing since then.
2 out of 4 answered...with an option on three...I'll get back to you as soon as I've beaten up my neighbour and stolen his phone...
Joke!
There should be somewhere you can go to test that wireless. I can walk outside the building I'm in and find one.
ChumleyEX said:
There should be somewhere you can go to test that wireless. I can walk outside the building I'm in and find one.
Click to expand...
Click to collapse
You = US, me = UK. We still think the biro is a recent invention...
Neighbour's phone on my network gives the exact same problem. I've also noticed that when I click "Renew IP" on the Kaiser it doesn't work...it gives me 0.0.0.0, but will occasionally flash up the correct IP address. It's alomst as if the connection is being lost and remade every few seconds. The status ist gives me is "associated to network"...is that different to "connected"?
I've been trying to solve this on my router, but none of the settings seem to make any difference.
Same here
I get the same with the router from sky.
Kaiser says I have an IP address, 192.168.0.5, but the it doesn't show up on the attached devices on the router.
What I find that works is hit renew IP maybe twice until you get a really wierd IP address like
169.254.*.**, actually not sure if I'm picking up another network, but for some reason I don't think I am.
I can then browse the web and sync via wifi.
Really pisses me of that it says that it has an IP address but doesn't connect.
1) Make sure you dont have a proxy set up on your wifi connection on your device.
2) The 169. address is your device getting an unauthorised IP address as the router did not receive the correct encryption key from the device.
3) You can check if its an encryption thing by simply logging in to the router (192.168.0.1 in your web browser on pc) and changing the settings to turn wpa off and testing it. The routers username and password are on the card - its something like "sky" and "admin"
Yeah I agree, there is something up with that router.
Grey Area said:
Neighbour's phone on my network gives the exact same problem. I've also noticed that when I click "Renew IP" on the Kaiser it doesn't work...it gives me 0.0.0.0, but will occasionally flash up the correct IP address. It's alomst as if the connection is being lost and remade every few seconds. The status ist gives me is "associated to network"...is that different to "connected"?
I've been trying to solve this on my router, but none of the settings seem to make any difference.
Click to expand...
Click to collapse
with my router.....i have to set the wifi power mode on my kaiser to "best performance", any other setting and i get that "associated to network" ****. been this way every since the hermes and the wizard.
unwired4 said:
1) Make sure you dont have a proxy set up on your wifi connection on your device.
2) The 169. address is your device getting an unauthorised IP address as the router did not receive the correct encryption key from the device.
3) You can check if its an encryption thing by simply logging in to the router (192.168.0.1 in your web browser on pc) and changing the settings to turn wpa off and testing it. The routers username and password are on the card - its something like "sky" and "admin"
Click to expand...
Click to collapse
No, proxy set-up as the device was bought unbranded in US.
Because there are issues with this router, encryption and media streaming devices, I have only restricted the mac addresses with no encryption.
Still don't know about the 169. ip address beacuse doesn't seem to come up as am ISP.
Now then, how wierd is this?
After all these issues and kind of giving up on it as a bad job, I also noticed that out on the road, my GPRS wasn't working either - TomTom couldn't connect to the "plus" traffic service.
I get on the phone to O2 who told me that my phone hadn't been "provisioned". After one false start where they didn't seem to do anything about it, I have just (literally) had them tell me to go to the O2 Operator settings and tell it to update the "O2 UK Post Pay_GPRS" and reboot.
GPRS now works. And magically, so does my WiFi - IP address negotiated and full access to internet and my router's setup page granted. Working like a charm again.
So - seems to me it's an account setting, and nothing to do with either me poor ol' router or me nice new phone.
For completeness, I was occasionally getting the 169 IP address too, so it sounds like we have EXACTLY the same problem - suggest you get onto your service provider ASAP.
ok, first of all, i checked every single thread on this page hoping to get a solution for my problem.
HTC Diamond, D-Link DWL-900AP+ Access Point.
My Diamond can "see" the Access Point, but is unable to connect with it.
Authentification WPA-PSK
Encryption TKIP
Networkkey Manually inserted and 100% correct.
Hook set at IEEE802.1x
EAP Typ = Smartcard or security certificate (but it's greyed out)
Network Card connects to Internet
From Server given IP Adress (hook set) DHCP on Access Point enabled
MAC Filters disabled
I also played around with the available network tabs.
I have vodafone DE, vodafone internet, company network or ISP
The the slider of the energy saving modus ist set to best performance.
What the hell is going wrong????
I also owe a HTC Touch Elfin and have no problems to access my network/internet.
Any suggestions would be highly appreciated
thank you
try deleting your network saved setting from list, make sure network card connects to internet, not work, find access point, and enter your password again.
this works for me in similar situations.
works if you start fresh, and not trying to connect with the same settings. i dont know why but has saved my ass a few times.
Also, try changing the encryption from TKIP to AES and see if that works....
I have the same problem! It's something about DHCP. My Diamond connects to my home wifi onli if I set the IP (which belongs to my phone on access point) address in the properties of network adapter.
HI did you try to put the host address of a site?
write 64.233.167.99 instead of google.it in case you can see the page the problem is the dns not resolved and insert manually in your phone connection
Marcellus_pnz said:
I have the same problem! It's something about DHCP. My Diamond connects to my home wifi onli if I set the IP (which belongs to my phone on access point) address in the properties of network adapter.
Click to expand...
Click to collapse
Same here, it looks like a DHCP time-out or routing problem. I've set up a DHCP server with a small pool of adresses on the acces point itself and now my Diamond always connects correctly. Before that, my Diamond would state that i had entered a invalid security key.
diamond connects but i cannot visit any website
Hi,
I have a similar problem. My diamond gets an ip address from dhcp, connects to dwl-900ap+ but i am not able to open any website (I tried to open some web with url and with its ip address too) - tried opera and IE too. In opera i get a "could not locate remote server" error. (Looks like a DNS problem?) I am not even able to open the AP's configuration web with diamond. Every other wifi enabled equipment I tried (1 notebook with win vista, 1 with XP, 1 with debian linux, nokia n95 with symbian and e-ten m700 with win mobile 5) works without a single problem. I also tried to reset the AP and my diamond - without success.
I didn't change any setting on the AP except for setting up a WEP encryption (i know, i know, it's not a strong encryption ), the SSID and the AP's ip address. Everything else is default. My dhcp server is not the access point. DHCP runs on a similarly configured router with wifi AP (diamond connects without problem).
Any idea/solution? thanks