XDA11i and bluetooth headset - PDA2, XDA IIi, 2020i General

Done this on loads of different devices with different bluetooth headset and the same result. Able to pair devices no problem. On making a call all one hears is a lot of static no voices. When answering a incoming call the same happens you answer the call but can't hear anything. Referred this the the ever helpfull O2 technical support who advised me to download latest Rom with the same result.
Any suggestions would be much appreciated.
Thanks in advance :roll:

Stupid question but you have tested the bluetooth headset with another phone and checked that its not actually the headset which is faulty?
I spent ages trying to diagnose a problem with my phone when I first got a wired GPS unit and it turned out in the end it was the unit not the phone.

Hi
I had the same problem. It disappeared after a hard reset.
Here is the similar thread: http://forum.xda-developers.com/viewtopic.php?t=41270

Related

Kaiser: bluetooth stack problem!

aladin2000 said:
Hi,
do you tried also a buttom to call with voice command application or a phone call ?
I've a HTC S100 and the sound is well but it's very difficult to start a voice commande or to recall last call because seem that the function "hand free" sometime is lose.
Sorry for my poor English !
Regards
aladino
Click to expand...
Click to collapse
I have the same problem with my handsfree headsets an Tytn II (kaiser):
i have a motorola H700 and a Scalarider headset for helmets.
They are bot NON-ADP and thyey support handsfree.
Sometimes the button on them stop working and I can't do voice dialing with Voice command neither repeat last call.
They appear as connected and If I manually call a number they work.
To get the button works again I have to restart the phone.
Maybe a fault in the microsoft bluetooth stack?
Also: my Motorola H700 has a flip and when you open it the headset turn on and get connected.
You should be able to answer phone calls by opening the flip.
Sometimes it works, but most of the time it doesn't connect if I open it while the phone is ringing and in that case I have to restart bluetooth connection to make it work again.
Microsoft or HTC should check end improve bluetooth stack!
Any hack around?
Can't we put the broadcom instead of microsoft stack on kaiser?
I wrote to HTC Support about this problem and they answered :
"Customer email address:XXXXXXXXXX
Good Afternoon,
The multi function button is the one small button with the led light in, not the big play/pause button.
If you try the other button, it should work.
Thank you for your enquiry, Should you have any other problem, please do not hesitate to call us. Your Local number can be found at http://www.europe.htc.com/support/csbyphone.html
Best regards,
XXXXX
HTC Europe
[email protected]
http://www.htc.com "
That's incredible don't you ?
They beleive I'm idiot ?
Regards
aladino
Astonished!
Amazing answer!
Are they idiot?
I'll write them too,
I hope someone cleverer will read the my mail
and suggest the bug to the technical stuff.
I have a motorola H350 and have been experiencing the same problems. It's driving me mad. The problem makes the use of the hands free totally useless as it seems to stop working at the drop of a hat.
What I've found so far.
To get it working you need to turn on the ear piece.
Then turn on the bluetooth on the phone.
If you do this any other way it doesn't work. Once it's working you may or may not be able to hang up with the button. If that's the case it won't answer with the button either.
Once it's working it seems to work ok till either the headset or the phone's bluetooth is turned off.
Voice dial will not fire up until the main procedure if followed and sometimes it takes several tries.
I was wondering if this was something to do with the motorola but seemingly it's to do with the stack so getting another device isn't going to help I guess.
The bluetooth worked perfectly on the Hermes but immediately I got the Kaiser one thing alerted me to the fact that something was different.
With the Hermes, as soon as I turned on the bluetooth and the earpiece the phone would alert me to the fact that the motorola wanted to connect.
With the Kaiser nothing, even when I searched for a device. I had to find out how to put the earpiece into search mode before it would find it.
Very flakey and very disappointing. I hope someone finds a fix for this.
Anyone else experiencing these problems?
I've got an H700 and Jawbone. I do notice more crackle type sounds and lower volume on both using Kaiser compared to my 8525. The H700 connects within 1-2 seconds when opening it's flip and I have noticed that on occasion, if I walk away from the phone (eg. phone on desk) the headset may not reconnect when I return. The Jawbone has been fairly good at connecting and staying functional at all times but the volume is lower as noted by many people.
I would say that the stack overall is better than the 8525's for all the devices I've tried (3 headsets, 2 Laptops, 1 Garmin Streetpilot with BT Phone interface)
I am also losing the Voice speed dial & redial button from time to time. It also worked that way with my hermes, so I kinda get used to it...
I am now wondering if it is related to my BT earpiece (nokia bh-200 or something like this) of if it is the BT stack which has never been really working on all the device I could test (hermes, trinity, kaiser).
I allmost never had issue recieving call (I don't recieve much call while using the BT earpiece) but it is sometime impossible to initiate a call through the BT earpiece.
The simplest way for me to lose the voice recognition is to:
-Start BT on the phone
-Start BT earpiece
Phone recognize the earpiece, everything is fine
-Restart the phone
Phone & BT reconnect, but voice recognition & redial are gone
I would really appreciate of some of you could test my little procedure and report if it works of not. If it is working for some other BT earpiece I may change mine and get rid of this eternal annoying issue.
Thanks
Jabra BT500
I have the Jabra BT500 and same problem with the TyTn II.
The earpiece can't initiate a voice call...
Looks like HTC (or Windows), starts to deliver ROMs like Mr. Bill Gates does with his M$ crap...
If someone find a solution for this Bluetooth problem, please post it!!!!
Thanks a lot,
Kaiser and Moto H700 just do not work together
I also have a problem with the Kaiser and a Moto H700. The M700 button stops working randomly, the BT connection sometimes disconnect during the call at will.
I can still use H700 successfully with my old Nokia 6680, so the problem clearly is in the Kaisers BT stack.
I’ve made the BT update that HTC posted just recently for TyTN II, but it had no effect.
Fortunately, I have my old Moto H500. This one is working OK with the Kaiser, but. Like it was pointed here before me, the only way to get it working you need to turn on the ear piece. Then turn on the Bluetooth on the phone.
In case if the Bluetooth connection was disrupted for some reason, the only way to make it work is again swath Kaiser BT off then turn on the ear piece and switch on the TyTNs BT.
The Kaiser’s BT stack is not good also connecting with a PC, the connection is just not stable.
Just wanted to chime in and say I've had the exact same problems with my Tilt and Motorola H700 as various people have described here. I posted about it on the AT&T forum too, and no one there has any working solution either, AFAIK. I too tried the "fix" from HTC, and to no avail.
This is a pretty big disappointment for me; I love my Tilt, but Bluetooth is not new technology, and it's really inconvenient that it works so poorly on this phone.
Motorola headsets seem to have a problem with this device. I had trouble getting my H500 to connect and the voice button to work. Once I reset the phone when the headset was on and it wouldn't connect. I tried deleting and re-pairing. It took another reset to get it back. Fortunately I don't use that headset anymore.
jameselee said:
Just wanted to chime in and say I've had the exact same problems with my Tilt and Motorola H700 as various people have described here. I posted about it on the AT&T forum too, and no one there has any working solution either, AFAIK. I too tried the "fix" from HTC, and to no avail.
This is a pretty big disappointment for me; I love my Tilt, but Bluetooth is not new technology, and it's really inconvenient that it works so poorly on this phone.
Click to expand...
Click to collapse
The same problem.
But this time with the Sony Ericsson BT HBH - DS980.
I also put the "fix" from HTC, I gave them back and they change them with another brand new Sony Ericsson BT HBH - DS980, but the problem exists.
costas2by4AIO said:
The same problem.
But this time with the Sony Ericsson BT HBH - DS980.
I also put the "fix" from HTC, I gave them back and they change them with another brand new Sony Ericsson BT HBH - DS980, but the problem exists.
Click to expand...
Click to collapse
I just bought the same headset... cant get it work with the TyTN II - Kaiser but pairs without any problem with my TyTN I - Hermes... clearly it is the BT Stack
Way beyond my abilities, but cant the BT stack on Hermes be cooked into a rom for the Kaiser ?
I have a Motorola HT820 and a Motorola S9 both devices are working flawless with the kaiser.
Now i own a motorola S705 too , with this device my kaiser suddenly turn the bluetooth off (
regards

Callers deafened by ringtone when I answer by Bluetooth

Anyone else got this issue and is there a new bluetooth stack or something to resolve it?
When I click the answer button on any bluetooth headset (currently using the iqua solar powered one), the sound is temporarily diverted to by mobile before the bluetooth properly picks up, and also during that slugging moment, any ringtone playing is diverted to the caller's earpiece (i.e. sent out by my mic).
One caller complained it had nearly deafened them.
Anyone able to help?
Having the same issue with my parrot bluetooth and my Tilt
Can someone purrlleeeease help with this issue? I am now scared to answer any calls, lest I get shouted at with, "GOD WHAT WAS THAT NOISE? IT NEARLY DEAFENED ME!"
You really haven't give a lot of info here.
I mean what Rom are you running, what BT hardware and reg tweaks do your use etc.
Info is required to be of any assistance.
Note my signature shows exactly what Rom(s) I'm currently using.
Many thanks. Here are my versions:
HTC TyTN II
ROM: 1.0 Sleuth
ROM date: 08/28/07
Radio version: 1.27.12.11
Protocol version: 22.45.88.07H
Essentially I think a new Bluetooth stack might solve it, but I really wish to avoid losing all data by flashing a new ROM altogether.
A new Bluetooth stack on its own would be wonderful... or a way to restore my data back to a newer ROM. Would Sprite Backup do that if I use Sleuth's WM6.1 ROM?
CJSnet said:
Would Sprite Backup do that if I use Sleuth's WM6.1 ROM?
Click to expand...
Click to collapse
I know the commercial version is supposed to support "Rom Upgrade" support but I'm not sure if that is in the version that is floating around the forums.
What you can do though is make a backup prior to upgrading.
Then upgrade to test if the problem is fixed in one of WM6.1 roms.
Then downgrade and restore your back-up.
Now you will know if there is even a point to expending the effort of trying to extract the BT Stack.
Don't take offense at this next statement but if you put forth that effort it might endear someone more skilled to your cause as you've provided a "Proof of Concept" so to speak.
Okay I have just upgraded to Sleuth's v3 (WM6.1). Sadly the bluetooth issue remains, despite the new Radio version.
If someone calls, and I answer using the bluetooth headset, for 1 second their audio is output to the speaker of the Kaiser. I believe it is during that second that they also hear the end of the ring tone, which is what deafens them.
An unsatisfactory workaround is to use a quite ringtone or vibrate only, but that is hardly ideal. If anyone knows of any other solution or a bluetooth stack that is a bit snappier when answering via headset, it would be great appreciated
CJSnet said:
Okay I have just upgraded to Sleuth's v3 (WM6.1). Sadly the bluetooth issue remains, despite the new Radio version.
If someone calls, and I answer using the bluetooth headset, for 1 second their audio is output to the speaker of the Kaiser. I believe it is during that second that they also hear the end of the ring tone, which is what deafens them.
An unsatisfactory workaround is to use a quite ringtone or vibrate only, but that is hardly ideal. If anyone knows of any other solution or a bluetooth stack that is a bit snappier when answering via headset, it would be great appreciated
Click to expand...
Click to collapse
Same issue here with the same new ROM.
I'm having the same problem. When I push the button on my BT HF it gives a horrible noise to the caller at the other end for a second. In my case I doubt it is ring tone, it doesn't sound anythin like the tone I'm using, it's just like loud crackling or smth.
I can't give you any version numbers cause by TyTN II is sent off to warranty (3rd time already). This time it stopped accepting and making calls while showing 3G symbol. Previously I had band selection on auto and had no problems. Now even after hard reset no calls could be made so off it went again. The first two faults where the speaker and the "Fn" light.
I am having the same problem, the handet is at HTC's repair facility for this and a few nagging issues. I will report what they find.
Mine isn't so much the ringtone it just sounds like a loud static sound. I thought it was the headset but I tried it with 3 different headsets and the Bluethooth in my car and they all have the same problem.
Got my phone back today and I can't say I'm impressed with HTC. First they requested that I send it in the original box then must have thrown it out and sent it in some crap box without enough padding. They didn't even send a note or invoice saying what had been done, which was nothing.
They claim they couldn't find anything wrong and when I called support the guy thought it a joke.
Needless to say it is still deafening and I am pissed.
Same Issue Here... It is almost as if there is a dely in cutting off the WAV/WMA file. Bluetooth Picks up and and both parties get the end of the ring tone.
Had the issued with the origional AT&T rom
Have the issue with Slueth 3.0 and Alex 5.2
If anyone finds a fix please let me know...
I am using PhoneAlarm - Don't know if that is related.
I've had the same complaints from some of my callers, and try to answer between rings as much as possible. The complaints have gone way down. Of course, we shouldn't have to jump thru hoops to answer our phones!
Does anyone have contact info to point HTC to this worrying thread? We need a patch release ASAP. A phone that can't answer calls properly? Yikes.
No issues with my BlueAnt Z9. Have you guys tried different headsets?
I think you may have just been lucky. It is uncommon to A) answer during the ringtone, and B) have the caller complain about the loud noise.
It happens on my Bluetooth earpiece, and Nokia car kit, and JVC car kit. So, it is for HTC to resolve.
I've tried three headsets and it happens on all of them. It happens even when I have the phone on vibrate.
I spent an hour on the phone with HTC support and they are awful, even after telling her that it happens on three different headsets she says that is sounds like a headset issue not an issue with the phone.
When I explained for the third time that I would agree if it happend with one headset but since it happens with all of the headsets it would support my arguement that it is an issue with the phone.
It was like talking to a wall. I wish I had an alternitive to HTC at this point, I love their design and have never had a problem with any of their other phones but this their lack of support is amazing.
I think its with all HTC phones. Happened with my Dash - Wing and now Tilt.
But I've never had anyone complain about hearing music on their end...I can just hear it on my headset for about 1 sec. I've also had my SMS tone play wile on a call and also my VM tone play while on a call and I've asked them if they heard that and they said no.
I also only use noise cancelling headsets.
VooDoo1 said:
I think its with all HTC phones. Happened with my Dash - Wing and now Tilt.
But I've never had anyone complain about hearing music on their end...I can just hear it on my headset for about 1 sec. I've also had my SMS tone play wile on a call and also my VM tone play while on a call and I've asked them if they heard that and they said no.
I also only use noise cancelling headsets.
Click to expand...
Click to collapse
I've never had a problem with any other handset, I've had a Qtek 9100, MDA, O2 Exec, Wing and a Dash.... crap I spent a lot on phones. The only one I've had problems with is the TyTNII.
Same problem here. And sometimes the speaker will very briefly go into speaker mode as I answer! Not good.

Tilt Goes Silent - I think bluetooth related

Hi everyone. I have had my Tilt for 4months now and it has given me a lot of joy. I have flashed and reflashed with no problems at all. I am currently using Schap's 4.31 Rom with 1.27.12.11 radio.
About a month ago i installed a new car stereo that has bluetooth connectivity with my phone - worked like a charm, paired very easily and generally appeared to be working with no probs.
Then i noticed that if i was in a bluetooth conversation and somebody else was calling (on call waiting), if i switched calls i could not hear anything, and if i ignored the second call, when the person on call waiting hang up, both conversations were terminated. I thought it was odd, but i just deactivated call waiting and thought, "let them try calling me later".
The other, a lot more serious problem, is that sometimes, randomly as far as i realised, the phone will go totally silent - incoming calls won't ring, and when i try to make a call, when i press "talk" then phone does not make that beep that it makes when an outgoing call is initiated. Should the person i call pick up i cannot hear them at all.
A soft reset takes care of this problem, but it has happened to me 3 times already, and i think it was after a bluetooth call.
Has anybody faced this problem before? I need to be available on the phone 24/7 due to my work and i really need to find a solution for this. Yesterday afternoon i took a nap for 45 minutes and had six missed calls that i never heard cause the phone never rang.
The phone is always on "ring" and at full volume.
Any ideas would be welcome.
Thanks
Alkis
Same issue
I'm assuming since I also am facing this same problem that it is not uncommon. It seems to me that it happens after a bluetooth device is turned off. Somehow it sets the volume on everything to mute. I thought only a soft reset would fix it until I discovered that it was just shutting off the volume. Still annoying, though.
Tilt problems with phone going silent
This problem has occurred with my phone every since upgrading to the WM 6.1 and it is related to a bluetooth device being hooked up. Often when someone calls the ringer will go from vibrate to on, but the volume turns all the way off. It will then cycle to off completely. The cycling occurs when a call comes in or when I hang up. I can stop this problem from happening by disconnecting the bluetooth head set. I have tried three different headsets and the problem occurs with all of them (Jawbone I, Jawbone II, and Plantronics) so I know it is not the brand of headset. HTC said to try a download of a screen dimmer problem, but have not done that yet. Anyone have any better advice?
did u guys ever find a solution to this?
its quite annoying missing calls because my phone decides to go silent for some reason
Same issue with GPS
I have the same issue, even when using software that accesses the GPS via bluetooth port. Muting is irritating, but at least voicemail catches messages. What really bothers me is that sometimes the mute is turned off and the volume up, especially when in a private meeting where we do not want interruptions
Gregg
HTC Tytn II bluetooth causes silent setting
I too have had the issue where my phone will go into total silent mode after using my bluetooth stereo hands-free feature. It doen't happen after using my bluetooth headset though.
It happens pretty regular that after using the bluetooth hands-free of my JVC car stereo that when I take the phone elsewhere it is totally silent. no ringer, no alarm (Ptravel alarm is what I use), no audio if I make a call (or receive a call).
It also will cause the phone to be silent on subsequent calls on the bluetooth stereo hands-free: ie: I take a call, hang up and another call will come in and I can answer it but have no audio.
My Tytn II is running the HTC (AT&T) WM 6.1 upgrade. The only thing I have done is use the Advanced configuration manager and the Kaiser tweak to change a few settings for performance and visual enhancements.
I see others are having the same problems.....Has anyone else used the tweaks and maybe that is root of the problem?
Has anyone discovered a fix (really important). My only options are to soft reset every time I get out of the car or not use the JVC bluetooth capability (which is why I replaced the stock radio in the first place).
Thanks
Hi rrackman,
I'd advice for you to look at the following thread:
http://forum.xda-developers.com/showthread.php?t=438457
It's quite long, so better subscribe to it and wait for responses. Several people with Tilt's have the same problem. Myself I have a JVC NX-7000 and an unbranded Kaiser (HTC TyTN II). It works fine with WM6.0, but I have the same issues you mention with WM6.1. First advice while we're searching for the solution: downgrade to WM6.0...
Regards,
Nika.
Is there a solution to this problem?
Try WM6.0 ROM - check out the thread I mention in my sig.
Regards,
Nika.
I did indeed take a look at the thread you linked earlier. Sorry for making the quick post earlier, I should have mentioned that this is regarding the "unexplained volume drop to zero" symptom, not the NSI symptom. Fortunately I don't have the NSI problem, just the drop to zero problem.
Of course downgrading to 6.0 would be the key solution, was just hoping to find a way to avoid doing just that. My phone never had the problem prior to 6.1 and was running the exact same list of applications and settings.

Bluetooth stops/crashes when connected to Car kit

Hi,
When my phone is connected to my car kit (Opel/Vauxhaul UHP) bluetooth sometimes stops randomly. I can turn bluetooth on again with the commmanager and everything is working again. But it can hapen again after a few minutes.
Does anyone have this problem to or even better a solution?
I allready tried all the different Radio Roms, but this didn't solve my problem.
Well with mine i have some hickus but it just happpends once a while.
Most irritating about Diamond and BT in my opinion is that wa have no equalizing for it. and the sound setup from the begining is horrible.
Asked here if anyone has a solution before but none replied.
But as far 2 your problem no. And i use a Pioneer system in my car.
Mauser.NET said:
Hi,
When my phone is connected to my car kit (Opel/Vauxhaul UHP) bluetooth sometimes stops randomly. I can turn bluetooth on again with the commmanager and everything is working again. But it can hapen again after a few minutes.
Does anyone have this problem to or even better a solution?
I allready tried all the different Radio Roms, but this didn't solve my problem.
Click to expand...
Click to collapse
HI
Same was happend with me (Opel), when my battery is low.
orsiga said:
HI
Same was happend with me (Opel), when my battery is low.
Click to expand...
Click to collapse
Mine is not low on battery, but I shall try it once connected to the cigarette lighter.
Nobody else has this kind of problems??
Mauser.NET said:
Mine is not low on battery, but I shall try it once connected to the cigarette lighter.
Nobody else has this kind of problems??
Click to expand...
Click to collapse
I've a JVC head and my bluetooth has no problem.
I have a Honda Accord with handsfree built in and I too am having problems. The phone and car both agree that a connection has been made but when i use it to either ring out or receive a call the radio mutes and when receiving the ringing tone sounds over the car speakers but I can`t hear the caller except on the phone which isn`t very useful. Would a ROM or radio upgrade help or is it just a compatibility problem
davemazo said:
I have a Honda Accord with handsfree built in and I too am having problems. The phone and car both agree that a connection has been made but when i use it to either ring out or receive a call the radio mutes and when receiving the ringing tone sounds over the car speakers but I can`t hear the caller except on the phone which isn`t very useful. Would a ROM or radio upgrade help or is it just a compatibility problem
Click to expand...
Click to collapse
I had this kind of problems also. Also syncing the phonebook gave me problems. You could try JETware, this solved almost all my problems, except now the bluetooth crashes
Mauser.NET said:
I had this kind of problems also. Also syncing the phonebook gave me problems. You could try JETware, this solved almost all my problems, except now the bluetooth crashes
Click to expand...
Click to collapse
Thanks Mauser. I tried Jetware as you suggest and I`m afraid it didn`t help in fact I think it crashed the handsfree system in the car like you. This is the final nail in the coffin for my Diamond. I just can`t get used to it so it`s off to Ebay with it.
davemazo said:
Thanks Mauser. I tried Jetware as you suggest and I`m afraid it didn`t help in fact I think it crashed the handsfree system in the car like you. This is the final nail in the coffin for my Diamond. I just can`t get used to it so it`s off to Ebay with it.
Click to expand...
Click to collapse
I'm sorry to hear that
I am very pleased with my Diamond... I would sooner put my car on eBay than my Diamond
Did you try to check almost everything on in the advanced settings of Jetware? I have also limited the phonebook sync to max 5 entries to debug and on the site of Jetware there wat a fix for Opel car kits.
Keeping my fingers crossed, but until now I haven't experienced any bluetooth crashes.
Mauser.NET said:
I'm sorry to hear that
I am very pleased with my Diamond... I would sooner put my car on eBay than my Diamond
Did you try to check almost everything on in the advanced settings of Jetware? I have also limited the phonebook sync to max 5 entries to debug and on the site of Jetware there wat a fix for Opel car kits.
Keeping my fingers crossed, but until now I haven't experienced any bluetooth crashes.
Click to expand...
Click to collapse
Thanks again Mauser. I tried various settings but without any success, I think the phone is just not compatible with the Honda. Having said that I don`t have much luck with bluetooth at all on the phone. More often than not It just won`t detect other bluetooth devices and when it does it won`t send or receive files so it`s time for it to go and I can go back to a trusty Nokia
Problems here with BT connection to car kit, too. I'm using the built-in car-kit of an Audi A4 (standard one not that with navigation, remote SIM, etc). I've noticed the following issues:
- when I try to make a call, the CD is cut off but NOTHING is heard in the car speakers UNTIL the other party answers the call (and then I start the conversation). No ringing tone, no nothing. I cannot hear the busy tone, or network failure/congestion tone and this is annoying since I have to keep an eye on the phone to see what's happening. I found myself checking the phone when, after calling someone, nothing happened and in fact I got a busy tone and the call ended.
- sometimes, when I receive a call, the CD stops playing but when I answer nothing is heard from the car speakers but only from the phone (as davemazo said also).
- when I receive a call, I hear in the car speakers a "standard" calling tone, not the ringtone I have assigned for that contact
I have to mention that with any Nokia I had before (and still have one as a second phone), these problems do not exist. I know there is a compatibility between Audi factory installed car-kits and Nokia, but BT is a standard and most of the functions should be supported despite the phone model/type. I've tried also with an iPhone and it's working great, as my Nokia do. I don't understand why it is like this with the Diamond. In fact, I think it is not related to Diamond itself...it's doing like this with ANY Windows Mobile device I've tried in the past (Orange C600, Samsung I600).
Are there any solutions for this? A CAB, a new BT radio, a software, anything?... I don't want to buy a new BT car-kit and try with different models until I find something compatible
Thank you for any info/tip
Rapier said:
Problems here with BT connection to car kit, too. I'm using the built-in car-kit of an Audi A4 (standard one not that with navigation, remote SIM, etc). I've noticed the following issues:
- when I try to make a call, the CD is cut off but NOTHING is heard in the car speakers UNTIL the other party answers the call (and then I start the conversation). No ringing tone, no nothing. I cannot hear the busy tone, or network failure/congestion tone and this is annoying since I have to keep an eye on the phone to see what's happening. I found myself checking the phone when, after calling someone, nothing happened and in fact I got a busy tone and the call ended.
- sometimes, when I receive a call, the CD stops playing but when I answer nothing is heard from the car speakers but only from the phone (as davemazo said also).
- when I receive a call, I hear in the car speakers a "standard" calling tone, not the ringtone I have assigned for that contact
I have to mention that with any Nokia I had before (and still have one as a second phone), these problems do not exist. I know there is a compatibility between Audi factory installed car-kits and Nokia, but BT is a standard and most of the functions should be supported despite the phone model/type. I've tried also with an iPhone and it's working great, as my Nokia do. I don't understand why it is like this with the Diamond. In fact, I think it is not related to Diamond itself...it's doing like this with ANY Windows Mobile device I've tried in the past (Orange C600, Samsung I600).
Are there any solutions for this? A CAB, a new BT radio, a software, anything?... I don't want to buy a new BT car-kit and try with different models until I find something compatible
Thank you for any info/tip
Click to expand...
Click to collapse
Hi Rapier,
I also had a SPV C500, MDA Compact, Qtek 8500, Samsung I600, HTC Touch Dual and now the Diamond. The only one which gave me no troubles was the SPV C500, but I think that was because this phone didn't support phonebook synchronization and had no network identification/signal strength over bluetooth.
After the SPV C500 it went wrong. First I noticed that after a hard reset it worked for a few days. Later (about 2 years later ) I found out that it was because the call history was going to long to sync over bluetooth.
Then I found Jetware in which you can limit syncing to any number of items. They even had a fix for the connection to my carkit.
Unit now... it works like a charm... but keep my fingers crossed
I don't know if your carkit is a Audi UHV, but I saw that they had a fix for that too! You have to just install Jetware and then run the fix-file from your phone. Good luck!!
P.S. I am in no kind related to Jetware, I just found out that it worked for me.
Yes, I have an Audi UHV 6634. Thank you for the info, I'll try that and post the results here. Though, my car-kit is not the advanced one and I don't have to sync anything with it (contacts or something else). It's most working as a plain hands-free device, no extra functions...speaking of which, I've noticed that on the phone is detected as "hands-free"...why not "car-kit" as I know a car-kit has other functionality as well? This is the "standard" BT device for any audio enhancements (even if it is a car-kit not a BT headset), or I have to activate something to be recognized as car-kit?
Mauser.NET said:
Jetware? I have also limited the phonebook sync to max 5 entries to debug
Click to expand...
Click to collapse
my Honda system doesn`t read the sim I can only dial out via handsfree using contacts i`ve entered into the Honda system otherwise I either have to read the number to the system and it will ring out (most of the time anyway) or make the call on the phone (illegally obviously) cancel the call and then say "redial" and the system makes the call. So uless I`m misunderstanding this setting I don`t think it will help me.
I`ve searched the Jetware website and I couldn`t find a fix for my Honda
UPDATE: So...I've downloaded it, install it on my Diamond (including the extension file for Audi UHV) and...no change. Everything as before with both issues. Disappointed, I've uninstalled Jetware then...surprise. AFTER uninstall, I can now hear through my car's speakers the ID ringtone Maybe some BT settings were altered and remained like this after uninstall, but I don't know why it didn't work when Jetware WAS installed...strange.
Anyway, many thanks...at least half of the problems are now solved and this only by install/uninstall a program...that's cool. I must now find a way to make the car kit ring when I make a call, this is still an issue.
P.S. I've seen that Diamond support Headset and Handsfree profiles...and when connected to my car kit is set as Handsfree. I suppose this is better than Headset...but still no ring out tone.
Rapier said:
UPDATE: So...I've downloaded it, install it on my Diamond (including the extension file for Audi UHV) and...no change. Everything as before with both issues. Disappointed, I've uninstalled Jetware then...surprise. AFTER uninstall, I can now hear through my car's speakers the ID ringtone Maybe some BT settings were altered and remained like this after uninstall, but I don't know why it didn't work when Jetware WAS installed...strange.
Anyway, many thanks...at least half of the problems are now solved and this only by install/uninstall a program...that's cool. I must now find a way to make the car kit ring when I make a call, this is still an issue.
P.S. I've seen that Diamond support Headset and Handsfree profiles...and when connected to my car kit is set as Handsfree. I suppose this is better than Headset...but still no ring out tone.
Click to expand...
Click to collapse
No thanx! I'm glad I could help
Mauser.NET said:
Hi Rapier,
I also had a SPV C500, MDA Compact, Qtek 8500, Samsung I600, HTC Touch Dual and now the Diamond. The only one which gave me no troubles was the SPV C500, but I think that was because this phone didn't support phonebook synchronization and had no network identification/signal strength over bluetooth.
After the SPV C500 it went wrong. First I noticed that after a hard reset it worked for a few days. Later (about 2 years later ) I found out that it was because the call history was going to long to sync over bluetooth.
Then I found Jetware in which you can limit syncing to any number of items. They even had a fix for the connection to my carkit.
Unit now... it works like a charm... but keep my fingers crossed
I don't know if your carkit is a Audi UHV, but I saw that they had a fix for that too! You have to just install Jetware and then run the fix-file from your phone. Good luck!!
P.S. I am in no kind related to Jetware, I just found out that it worked for me.
Click to expand...
Click to collapse
Hello,
I have a Mercedes car kit and facing the same issue as you: everything works perfectly for a few days when hard-resetting my device, even with my 500+ contacts (they are loaded in less than a minute), but after a few days/weeks I can't get to have my call history or contacts displayed in less than half an hour!
Yesterday I thought I'd just hard reset my device because I had this problem again, but unfortunately it didn't work!
Guess what I have done differently this time: yes, I backed up and restored my call history, which I hadn't done the previous times! So I guess it is indeed related to the call history, but I can't test for now!
I have installed JetWare and limited the call history to 5 numbers, I'll try this tonight and I'll keep you informed...
Hello,
So I have tested this yesterday (installed Jetware and limited the call history to 5 numbers), and now it works FLAWLESSLY! I can browse through my 500 contacts instantaneously when I pair my phone with my Mercedes car kit.
So, in my case it was also clearly the CALL HISTORY that was causing problems... A BIG BIG thanks to Mauser for pointing out this!
I'm also having problem connecting my Diamond to my Volvo S80. All the other functions work except that I could not hear the other party through my car stereo and I also could not diconnect the call with my car end key.
I'll try the Jetware and I'll report back later. Thanks for the pointer.
turt said:
A BIG BIG thanks to Mauser for pointing out this!
Click to expand...
Click to collapse
No thanx! ... glad I could help

X1 wired headset receive calls problem

Hi!
I have one black X1i SW ver R3AA010, GENERIC_UK rom.
Great phone, but i have problem with the wired factory headset.
If i have call, phone playing ringtone, and i want receive this call, but no effect. Another problem is mic is on the phone enabled, not on the headset - in ear-phone mode.
On another forums reported same problem.
I see now only one solution:
1.,Unplug Headset from phone
2.,Incoming call, after hearing rintone - plug in the headset
3.,Problem is fixed..., but only to next soft reset or next unplug
Is there any registry mod or cab fix to this?
example : manual headset mode on/off
pls help me, thank you
As you mention, the problem has been scarcely discussed in other threads (and forums), but no one's seemed to find a solution. I'm not even aware if the headset problem is a general flaw in X1, or we're just a few unfortunates.
I won my X1 in a competition so I don't think I'm really in a position to be pissed off, but this defect is indeed a MAJOR drawback, and it surprises me it hasn't been criticised more loudly in e.g. reviews and forums.
The problem smells to me like a firmware issue (though I really don't have a clue), i.e. something that our friends at Sony Ericsson (are you out there, guys?) should be able to fix in an update, but they don't.. :-(
Anyway, my workaround is to make sure the headset is 'armed' in advance whenever I want to be prepared for an incoming or outgoing call. E.g. before I hop on my bicycle, I 'simply' make a short call to whatever number, e.g. to my voicemail, and as soon as there's a connection I plug in my headset and hang up. Now the headset works - I test it by pressing the headset button twice, which should initiate redialling the last number used.
In any case, it shouldn't be necessary to make such arrangements! My previous mobile was a crap, crap Nokia - but I miss it because its headset worked like a charm.
In fact, just out of curiosity - if anyone reading this has an X1 without any headset problems (i.e. mic and button not being responsive), please speak up. Maybe we can then isolate the problem.

Categories

Resources