How do I restore my PDA to a working state after running HimaClearJumpCode.exe on the device.
All I get on the PDA screen now is "USB/Serial" and "V1.01"
I was trying to uppgrade to WM5 before I found out ther is no WM5 for the
Qtek 2020i :-(
UPDATE: Never mind figured it out
himaclearjumpcode
I DID IT!
Now the only thing i got is seria/usb and v1.03
how can i get out of it and have my xdaII back?
please help me
Does hitting the soft reset work? Or did you actually begin the upgrade process? Seems that you're stuck in bootloader mode.
Related
Hi all,
I copied EnterBL.exe to my MDA III and now it immediately switched to a bootloader screen. The bootloader Ver is 2.05.
I have tried, resetting, hard-resetting and holding down Camera+Power and pressing the reset button, but nothing seems to work. Every time the bootloader ver2.05 screen comes back.
Any ideas? Help please [/b]
Try to reflash the rom. It may be a good excuse to upgrade to 1.40. You can find out how, here:
http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade
Other than that, I can't imagine what else could work.
Problem Solved
Thanks a lot. Even though ActiveSync was not connected, still running the upgrade programme worked and now I am running a 1.40 i-mate Rom. Lets see how it goes.
Once again thanks a lot.
No problem. Writing that wiki page once took out all the work of explaining it each time .
Hello!
I tried to flash my Charmer with the new german Aku 3.3. At first everything seems to be ok, but at 95% it stops and i got the Message: update error- there is an comunication problem! So what can i do? I tried to flash the old rom back but there comes also at 95% a message: invalid command - nfb file cannot be used for your pda!
Please help me !
Greetings Musna!
Ps: can somebody upload a sd image for the mda compact II !
Go to bootloader mode, then try to flash RUU rom (1.x). You can find it on Charmer wiki.
It doesn`t work too, it always stops at 95% has anyone another idea?
did you try hard reset?
Yes i tried hard reset, but it is always in bootloader!
I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!
nitrane said:
I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!
Click to expand...
Click to collapse
The aku3.3 is up to date the bootloader version!!!
IPL and ISP version now is 3.00.
http://www.windowsceportal.hu/forum/viewtopic.php?t=1079
Sorry but i do not speak hungarian. What do you want to tell me ?
I´ve got the same: My charmer is in Bootloader IPL 2.06.0001 SPL 3.08.0001
I can´t downgrade to AKU 2: Please order a newer Version.
Every try to upgrade to AKU 3.3 failed at 95% with Error 326.
Is there any help for my charmer???
oh.**** !!!! I got the same problem with them and my first pda uk rom already empty screen and then i try with my scrond pda German rom it the same problem and now just only show in bootloader screen.Have i ask someone who knowage about this he told me that if SLP in you PDA have chang it be hard to repair.So,I think I lose 2 PDA did I try to flash in T-Mobile Official Rom de that i hope to develop it but i hve to kill 2 Charmer.Who take responsibilities,T-Mobile right ???
Ok no problem you can repair it! At first you have to brand your device with the rom you want to! After 95% the Problem will come again! When it stops you have to go with a reset to bootloader again.When your device is in bootloader you have to install the Radio Rom from this thread:
http://forum.xda-developers.com/showthread.php?t=302768
After that your device will be able to boot again and it should work!- But the Problem during the installation will stay,so you have always to use this way to flash your Mda compact II!
In the new rom there must be a problem with the radio rom and this causes the broken device.
I`m sorry for my bad english but i`m not used to talk very much! So i hope you understand what i mean!
Greetings from Austria Musna!
that link is broken
Then try this one:
ftp://xda:[email protected]/Prophet/Radio_Roms/Prophet_G4_RadioRom_v2.47.11.exe
You can find the radio rom also on the ftp server. Prophet> Radio Roms>Prophet_G4_RadioRom_v2.47.11.exe
You can try different Radio Rom versions, i have flashed the v.247.11 and it worked.
Normaly it should work!
Thank u so much !!! My Charmer secrond PDA come back have life again and it can working.So,my Charmer first PDA UK rom still empty screen and notthing working when i press any button.Who can slove this problem !!
Musna do you have any massage such as msn
I downloaded a wm6 upgrade pack from Demonoid. The instructions told me that I needed to load an older rom on before I could CID unlock. The ROM was: CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE. The ROM that was originally on my 9100 was the lastest from Qtek. My Qtek now will not move on from the splash screen. Does this sound like I have a dead pda? Anyone have any idea how to get out of this problem. Any advice or comments would be appreciated.
Thanks
PS: I turned it off for the time being. Now I can't even turn the dam thing on!
I think I may have found a solution if I can just turn it on!! Won't charge either!
Well if u can get it turned on hold the voice and cam buttons and get it into bootloader you'll be good
I tried flashing WM6 on my QTEK 2020, but I had the wrong version. I begun the upgrade having it on bootloader and after a while an error about updating radio occured. Now, my PPC powers up, but it gets stuck on the beginning with the "QTEK" logo with the clouds and the blue led that indicates the bluetooth is activated. Neither soft nor hard reset does anything and I can't flash the original rom through bootloader (I can boot the PPC in bootloader).
Does anyone have any idea please?
If you posted this in the Qtek2020 (Himalaya) forum, you might get a quicker response.
Thread moved out of the BA section
Maybe you should try reflashing. Just flashing a new ROM and then just a radio might do the trick.
How did you flash? With the No_ID?
And what were you trying to flash? A BA ROM while you have a HIMA?
OK!
It's ok now! I flashed the WM6 Rom having my PPC on bootloader and everything's fine!
Its very good to hear that..btw which rom did u flash before and what have u flashed now
I really can't remember what the previous rom was, but it was for another brand! It was stupid to flash that one! The one I have now is this:
http://forum.xda-developers.com/showthread.php?t=332945
But I have a problem. The PPC restarts randomly even if I do nothing with it. I haven't overclocked it.
It is not got sign, if your PPC restarts randomly. Better you flash it again.
I flashed again the ROM from "Himalaya Mobile 6" category and the following link:
http://forum.xda-developers.com/showthread.php?t=332945
but my PPC keep restarting and one more thing, WM6 kills my battery! I've got to charge it every day, before I charged it every 3-4 days. Does anyone have any idea what I should do? Can I put WM2003 now?
Hmmm... I'm using the 7c ROM from that page with no problems at all.
Did have some issues with some older apps and the config for TomTom when I switched to WM6, but not anymore.
What do you have installed, and what versions?
I have installed nothing but WM6!
have a charmer. I tried to put wm6. but spl and ipl was 1.12. the phone start up and hang when installing some cabs. i restart ir and it allways crashes at t-mobile logo. i updated the rom to aku 3.3. all ok. but continues chashing on t-mobile logo. i try a hard reset. gives me a fat error. I try to put the rom from prophet to try to format it. but that rom upgrade reach 95% and stop. give me a error. this nbf file cannot be used to upgrade this device. I tryed all types of roms. most of them crashes at some point and give me that error. the rom aku 3.3 german and wwe, install perfect. I think that is the only roms I can send to my charmer. but i can´t format whith that rom, fat error. I have 3.08 spl ipl 1.12 because i sent an old charmer rom. ipl downgrade, but spl don´t. do you think my device can be protected?? I dont know that to do more, to bring the charmer back to life. will sd card method work? please help me.
Charmer dead after wm6 update whitout cid unlocking
Hi @all
i have the same problem.
iam stuped and make an wm6 update from ipl1.12 and i have forgot to cid unlock my charmer.
after the update to wm6 all looks like good. the bootscreen from wm6 i have see.
after the reset the charmer hangs at slashscreen.
now i make a update to aku 3.3 ger.
that works but hangs in the t-mobile spaschscreen.
i have tray all downgrading methodes i have read here but nothing works.
jet i have a ipl 1.12. and spl 3.08.
I think only a sd-card rom update works. but i dont have found an sd-card rom to use.
sorry to my bad english.
please can anybody help me?
cu AxelD
Is my phone already dead? Please help me!
Hi, I have a similar may be the same problem!
My phone is a German t-mobile mda compact 2
First I work with “lokiwiz v.02” to unlock the SIM, and it works really well.
Then I installed “Charmer_Touch_ver._2.1” and I could calibrate the screen, and after that Win Mobile 6 installed all the extra stuff automatically. After that the device made a reboot, but it stop at the t-mobile boot screen.
Because the bootload modus is still running, I installed the newest original t-mobile software “RUU_compactII_AKU3.3_38222_382117_026921R_TMO_DE_GER_Ship” but this also didn’t solve the problem.
Hard reset didn't work and always says "Format is
The Start screen shows me this information:
IPL 3.08
SPL 3.08.0000
GSM 02.69.21
OS 3.8.2.22
Is my phone really dead or could someone tell me a trick to reactivate it?
I think noone have a solution for us. I tried to send commands to phone whith mtty. and I can´t send. I don´t know why. so f we cannot send commands the sd card method will not work too. the only olution is to jtag the charmer. but can´t find any pinout information. if anyone knows this informtion, please help.