Hello guys!
I got my MDA Vario last week, and I am very much impressed with it!
I got the MDA Vario brand new without a contract and my intention is to use it with one of those O2 Genie PAYG SIM cards. So.... after much reading this excellent forum I figured out that I would need to unlock the SIMlock on the Vario. Got hold of the Lokiwiz utility, followed the advice on these forums, and tested it with the Orange SIM in my regular phone, and hey presto.... MY PY PHONE IS UNLOCKED!
Next step - to remove all T-Mobile customisations. Again, I had a simple bit of advice from one of you good folk - hard reset, then soft reset when the phone starts to install customisations and now all the pink girlie stuff has gone! Only reminant of T-Mobile left on the phone is the logo on the phone dial keypad.
My thoughts are now with upgrading the ROM. T-Mobile have been very slow with updating their ROM package -a new one is apparently due very soon. Now.... in preparation of installing a new ROM, Ive CID unlocked my phone. I would really like to know which ROM I should upgrade to - there are so many out there! As the phone has been CID & Sim Unlocked, does the phone remained unlocked irrespective of what ROM I install? Can I install a T-Mobile ROM after changing it to another?
As I intend to mostly use an O2 PAYG SIM in it, would it be better to use a new 02 update? If so, which one? Or do I go for another ROM? All very confusing! Finally, Ive heard that I cannot browse the net via GPRS on an 02 PAYG SIM. Is that true? Do I need to flash an ExtROM too?
I know Im asking a lot here and am being a bit of a pain in the backside, but I would really appreciate any and as much advice as possible as I realy dont want to end up with a dead phone! Many thanks in advance!
Hi, yes you could wait for the new rom and i am a believer in sticking with your manufacturer roms because many of the posts here seem to people experimenting with different roms and it all going wrong - lol.
But if you do upgrade proberly the commonest choice is the aku2 qtek rom that i use
download here ftp://xda:[email protected]/Wi...digy_2170702_21707102_20710_QTEK_WWE_Ship.exe
and the o2 aku2rom not a bad idea too, but without the o2 extras.
Yes you could then upgrade to the t-mobile rom then but often you need to unlock again with lockiwiz 0.3a.
PAYG o2 will browse internet but msn etc.. does not work.
btw yes you are a pain in the arse but then most people here are!! :lol:
Cheers Mark! Nice to have some basic advice - very reassuring for a thicko newbie like me!
Well... I couldnt wait for the new T-Mobile ROM and went ahead with the upgrade with the Qtek upgrade you suggested.
Was a little tricky at first because the upgrade wouldnt happen (port failing to open) but I had a few programs running in the background on my desktop PC and shut them all down so that I had a `Clean` PC. The upgrade process was then as smooth as a babys bottom.
MDA Vario is running really well - well worth the upgrade IMO. Everything seems quicker and generally better. Only problem I have is with wifi - it seems to take ages to make a connection with my PC (ad-hoc peer to peer) whereas on the original T-Mob ROM it was very quick. Any ideas here?
I read that you say I would need Lokiwiz 0.3a to install the AKU2 T-Mob ROM when it is eventually released. I was under the impression that once the PDA was unlocked (lokiwiz 0.2b) I wouldnt need to unlock it again. Is it different with the very latest T-Mob ROM? Can I not revert (downgrade) to the original T-Mob and then upgrade to the new T-Mob ROM? Ive not heard of lokiwiz 0.3a being out yet - would it be as simple as unlocking with lokiwiz 0.2b?
Finally, how on earth do I get the latest 02 ROM? I need to enter my 02 mobile number and IMEI to download it. Do I need lokiwiz 0.3a to install that or any other current ROM?
Cheers for your friendly advice.
Al.
Hi, no problem - glad to help.
Lokiwiz 0.3a is out see here http://forum.xda-developers.com/viewtopic.php?t=50768
For some reason when upgrading (in think it renews cid/spl) to aku2 rom seems to lock again - i had to unlock my qtek with above tool.
Yes you can go back to original rom - but if does not work use farias method of unlocking and downgrading rom (post is in this forum)
Most of the roms are in the wiki http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
including the o2 roms, but i would refrain from too much chopping and changing because you can destory the bootloader and then has to go back to the manufacturer.
Many reported problems with the wifi setting up - i would read some of the threads in the wizard forum if i was you. First thing to try is tweak wifi on device to wlan g and it may work better.
see registry tweaks here http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
btw good to hang out in the wizard forum too - you will learn alot of tips from there.
Want to also say thanks from another newebie with T-Mobile MDA. Have unlocked phone and CID and flashed with 2.17 QTEK ROM and all is good.
Thanks !!!
if you want th get rid of the tmobile crap on the face...use a 2p coin and move it downwards...not accross
it takes the tmobile paint etc off without any marks..
Jesus sbouri that logo was killing me, brilliant tip, nice one mate!!!
hi
i just got my mda vario and manage to unlocked the phone with lokiwiz03. i know my phone is now sim unlocked, but how do i check if it is cid unlock as well?
i am eager to flash the rom with the qtek version but i have no idea how to do it.
i know i must have my phone cid unlock in order to install a different rom, so do i just download the latest qtek rom, connect my device to usb and activesync it, and then just run the RUU?
i am really noob here.
cheers.
Hi mate if i was you i would use MR CLEANS ROM i flashed with that and its excellent, tottaly clean with no tmobile crap and i didnt do anything with the cid so dont worry.
ftp://xda:[email protected]/Uploads/Wizard/ROMS/MrClean_RUU_WIZARD_224_AKU23_WWE.zip
Just download this and run follow instructions, real easy. Good luck mate.
thanks for the advice...i took a bold move and flash it with a qtek rom. works like a charm. before that i did cid unlock using lokiwiz02a, not lokiwiz03.
i will take a look at mr.clean rom at a later stage.
i notice that my imei number is different from the one in my box. does flashing the rom change it?
now my next task would be update to a better radio rom and check out the extension rom.
cheers.
SBouri said:
if you want th get rid of the tmobile crap on the face...use a 2p coin and move it downwards...not accross
it takes the tmobile paint etc off without any marks..
Click to expand...
Click to collapse
Great tip, worked like a charm and left no marks.
Thanks.
Hi there, I'm about to flash my UK MDA Vario too.
I'm not sure to use the Mr clean one or the Qtek 2.17 version.
Before I do anything, which is better of the two?
Also, what settings to I need backed up? I have my txt msg service numbers, as well as voicemail. And all of my MMS & GPRS settings.
Am I to assume that all I have to do is input the settings into the device once it's been flashed?
Thanks
Scottland said:
Hi there, I'm about to flash my UK MDA Vario too.
I'm not sure to use the Mr clean one or the Qtek 2.17 version.
Before I do anything, which is better of the two?
Also, what settings to I need backed up? I have my txt msg service numbers, as well as voicemail. And all of my MMS & GPRS settings.
Am I to assume that all I have to do is input the settings into the device once it's been flashed?
Thanks
Click to expand...
Click to collapse
The mr clean rom is a more advanced rom and has no extras. The qtek official rom is probably a safer install because its an official rom and many good reports of success and users pleased with the outcome.
Yes when you have flashed just input all those settings again.
Plus you can backup your voice tag database between hard resets by copying the file CommandModel1.bin found under the windows folder to your pc or to the memory card. After rom upgrade copy it back to your windows folder and all your voice tags are back!
Create backup of windows\start menu - most programs that are on the storage card dont need a reinstall.
Create copy of pim.vol in the root directory of the device - contains contact and appt information. After flash change the new pim.vol to pim.vo and copy and paste old pim.vol (use total commander or gsfinder file explorers for this) and soft reset and you will have info back.
Create backup of windows\favorites - for all your internet favorites.
That will make restore a bit quicker than otherwise.
Cheers for the info. I was actually thinking of trying the Mr. Clean one first, is there anything missing from this one, or is it just less stable?
Mr clean is just a clean rom without any of the manufacturers addons. It will probably run very well - its the flashing process with it that may not be as safe as an original rom and may possibly destroy your bootloader etc.. so you have a brick phone. I would always go for the safest option and would not suggest chopping and changing roms. Read the many users stories where everything goes wrong and the forum needs to help them out.
meschle said:
Mr clean is just a clean rom without any of the manufacturers addons. It will probably run very well - its the flashing process with it that may not be as safe as an original rom and may possibly destroy your bootloader etc.. so you have a brick phone. I would always go for the safest option and would not suggest chopping and changing roms. Read the many users stories where everything goes wrong and the forum needs to help them out.
Click to expand...
Click to collapse
True, I didn't think about that. Thanks again.
Ive been using Mr clean rom for 1 week now and its excellent from my experience. Its tottaly clean and runs so fast!
By clean i mean it has no customizations as you will find on official roms. It flashed just like any other rom too. Easy as pie. Just my info as people would like to know.
I've just upped to the QTEK ROM, and I've a couple of problems, nothing too serious though I don't think?
Firstly, when making my GRPS connection - I can't seem to find anywhere to input the WAP Proxy settings?
Edit, sorted this one now
Secondly, when settinp up my MMS - I can't select connect via Picture Message in the settings, it's not there?
I'm guessing this is some other connection I have to make up?
Any idea guys?
Scottland said:
I've just upped to the QTEK ROM, and I've a couple of problems, nothing too serious though I don't think?
Firstly, when making my GRPS connection - I can't seem to find anywhere to input the WAP Proxy settings?
Edit, sorted this one now
Secondly, when settinp up my MMS - I can't select connect via Picture Message in the settings, it's not there?
I'm guessing this is some other connection I have to make up?
Any idea guys?
Click to expand...
Click to collapse
I cant find what you say under settings - what does it do?
Never mind ignore me, that'll teach me not to read T-Mobile's site correctly
Related
now obsolete
new aku2 here
http://forum.xda-developers.com/showthread.php?t=279908
so am i right in presuming that the gprs settings and phone settings are present in the rom? if not, how do we find them?
ALSO:
T-Mobile are releasing a rom update this month (ie this coming week!) so it might be worth looking at what they have done, not just for wifi fix but any other maintenence changes. Apparently they do alot of testing on their roms so there might be useful stuff there.
t-mobile gprs and wap settings are part of the extended rom. the 3 cabs files that begin CAB-Customization-...
i didnt include them as i'm on O2. This is more like a 'Qtek' version for the charmer, a universal version. doesnt include any operator specfic content.
looking forward to that update, hopefully its aku2, everyone else is releasing theres at the moment.
SDIO
What about SDIO drivers in this debranded OS?
so if i back up my current rom cabs and then install this, if it all goes pearshaped, i can relaod the origional and not end up with an expensive paperweight?
i wanna do the deed, but am scared as hell with it being my first PPC and only a few weeks old at that.
but anything to speed it up, its like im running windows or something.......
oh!
:wink:
only way you could mess up is if you pull the plug or have a power cut! while uploading the new os. remember to backup all your contacts and stuff as you'll need to hard reset.
you can start all over again if it doesnt boot or something by using the install package on the t-mobile site
http://t-mobile.iris-global.com/download_manager_mda_com2.html
just go into the phones bootloader, with the phone off, hold down camera and plug in the sync cable until the 3 color boot screen comes up and run the install package to go back to factory.
It worked!!
Dear dave106 and all;
i tried your fantastic upgrade yesterday. This was my experience:
1- I works like charm!
2- you might find it easier to use Total commander to uncheck 'system' and 'read-only' in the properties of the windows folder on your charmer, before Unlocking CID (to avoid any error).
3- alternatively you might use Lockiwiz 2b from this forum to unlock and unlock CID first.
4- the ROM upgrade went fine, showed some error messages on the charmer screen (nothing to worry about) but did not indicate an end. I unplugged it after 20 minutes. It rebooted on itself et voila, it was up and running.
5- Changing the boot scrren went very smoothly.
6- I noted that the T-mobile customization (after the new config.txt) did not install at all. I had to manually install the CAB listed in the config.txt file to reload the MMS and GPRS settings.
But now my charmer has no T-mobile crap on it...
However, i did not notice any dramatic change in speed....
Ill check your unbraded rom for wifi sdio capabilities over the next few days (on a 'just in case' basis). I'm just recovering from a totally borked pagefile on my main pc so ive been too busy to try as of yet.
is this howto working on that device ?
http://www.vodafoneshop.de/shop/det...schaeftskunde&I_ID=4000&Artikel_Daten_ID=3208
or can i damage something with your howto over there ?
supreme2k said:
is this howto working on that device ?
http://www.vodafoneshop.de/shop/det...schaeftskunde&I_ID=4000&Artikel_Daten_ID=3208
or can i damage something with your howto over there ?
Click to expand...
Click to collapse
thats a wizard, so you can just cid unlock it and install the imate or qtek wizard roms. the mda compact 2 is unique to t-mobile no other operator has it.
aeh....your sentence sounds strange to me, is it possible for my device or not ?
supreme2k said:
aeh....your sentence sounds strange to me, is it possible for my device or not ?
Click to expand...
Click to collapse
lol, in a word, no.
i am from czech and i dont understand all of this.
This is OK? or only any idea..
is really decustomization my mda compact II? I have tmobile
(i dont can it)
i flashing new rom....
after 10minutes say my mdac "aplication repllog.exe dont start"
...update is OK, and i have second problem
when customization is start it said " \Extended_ROM\CAB-Customization-Connection-TMUK-Charmer-Nov15.sa.CAB"
DOESNT IT, I DONT HAVE THIS FILES IN EXTENDED ROM ++
and third problem, my storage card doesnt work ( i have2gb pretec...
only after the update
dead link
Can someone please post a working to the debranded rom? The current link does not work :-(
Thanks,
Dzim
funkus said:
Ill check your unbraded rom for wifi sdio capabilities over the next few days (on a 'just in case' basis). I'm just recovering from a totally borked pagefile on my main pc so ive been too busy to try as of yet.
Click to expand...
Click to collapse
Funkus,
did you try wifi sdio with this debranded rom?
tnx
Re: dead link
Dzim said:
Can someone please post a working to the debranded rom? The current link does not work :-(
Thanks,
Dzim
Click to expand...
Click to collapse
try it now, some tit nuked the uploads again
Got the Rom Working, the difference is quite noticable. Re wrote the extended ROM to auto customise just enough to get the MMS and GPRS to work correctly. Did any one work out if a WiFi card SD card will now work?
Would like to know before i buy one!
Re: dead link
dave106 said:
try it now, some tit nuked the uploads again
Click to expand...
Click to collapse
Thanks a lot, I have spent few hours searching the Web for this file, but couldn't find it. Thumb up!!
Dzim
aWizard not reconizing os.nba
Hi,
have followed instructions as above but when I go to write new rom it can't find os.nba.
Anyone have any ideas on what i'm doing wrong or what to do next?
I'm a noob, obviously :roll:
after searching through Google and MoDaCo, I've come to the conclusion that the latest ROM for the Vario is 1.6.2.4 (WWE)
As far as I understand, there was supposed to be another update but it's been pushed to July.
This update is the AKU2 update (I dont know what it means)
Some said that installing the iMate K-Jam AKU2 onto the Vario will work, but will remove all T-Mobile apps and settings.
Is this true?
If so where can I get the apps and settings back as T-Mobile's website is a blank.
Now if all is well, where do I get this latest ROM?
Should I take any precautions?
What will I gain and lose system wise?
Finally, does anyone know where I can unlock the device.
Sorry for the truck load of questions.
Just want the best since I just got my vario and it seems pretty sluggish. A person from esato said that AKU2 would fix that.
What is the best ROM to install onto my T-Mobile (recommended)
(also, if the rom isn't like a regular executable, how would I install it?)
Kind regards!
Go to the Wizard forum and read the lokiwiz thread for unlocking - essential if you want to run different ROMs
A search on TMobile settings will bring up many posts but it's going to vary according to whether you use TZones or the unlimited internet access.
Apart from the internet access and, maybe, MMS I'm not sure what other TMobile stuff anyone would want.
I run the latest QTEK ROM and can recommend it for speed, stability etc etc and configuring MMS and Internet is no issue.
thank you very much for your prompt reply.
I did spot Loki and unlocked my phone, however I assume you mean CID Unlock am I correct?
What I was referring to when mentioning losing anything was any apps.
I am unsure if there is anything that T-Mobile Provides that I will need.
Is there any program that can back up the whole phone for free?
(that way I can back up settings and apps, upgrade the rom and then restore everything)
you recommended the Qtek rom because it's the latest, there were a few roms which said "Latest" but were not, just so that I do not make an error could you link me to the correct thread?
As I'm sure you understand, I'm worried that I might do something stupid and end up with a brand new brick.
edit:
I just purchased SPB Backup.
I'm hoping that'll be enough.
edit2:
I noticed in a thread below my thread that the latest Qtek rom causes some battery miscalculation and a drain for some. Is this still the case, is that the latest rom?
Can you link me to the appropriate rom?
Sadly it seems the battery meter is moved to the top.
Is it recommended that I wait for the T-Mobile Rom to be released?
What am I missing out on, besides better speed (since mine lags like nuts)
I'm sorry again for the questions. Perhaps my thread can be a sticky for beginners?
Kind regards, and thanks again.
Kei
edit3:
lol this is the first time this has happened (I recentley unlocked the phone and did a backup) but it just soft reset on it's own...
Is this common?
Wow, lot of information.
Latest QTEK ROM is the 186504-ruu_9100_2170702_21707102_20710_qtek_wwe_ship.exe
You need to CID unlock to install ROM's from other vendors.
There should not be any downside to the process though I'll qualify that when dealing with technology anything can happen. Read the lokiwiz thread in full and you'll see most of the good and occassional problem.
Not having ever used a TMo ROM I don't know what they bundle in there. However, I use TMo service with the QTEK ROM and have no issues - just had to cingure the GPRS for internet and the MMS settings.
No idea what the soft reset could be I'm afraid.
would you (or anybody)
be able to confirm battery problems after installing the latest Qtek rom?
(Or battery miscalculations)
I've downloaded a file called RUU_Prodigy_2170702_21707102_20710_QTEK_WWE_Ship.exe
I'm assuming thats the right one.
Does anyone know how to get the battery icon at the bottom and the clock at the top AFTER installing the Qtek rom?
Although people say the rom is more stable (wont reset so much)
I still don't know what I'll be gaining. Of course if it'll double to speed then it'll make it much worth it, because the K-Jam is sllooooow.
well it's been a while but I just wanted to confirm that the battery is indeed inaccurate.
I haven't found a way to move the battery icon and clock around.
Is the rom I mentioned still the latest and best?
Can someone link me to the latest and/or best (EVEN if it is the same ROM)
Sorry, but i am a newbie i just got my MDA, it sometimes freeze up on me, so i talk to a friend he said try upgrading the firmware, so i wanted to upgrade the firmware just dont know which one cause there's so many...i wanted Tmobile USA, with all of the Tmobile programs such as MMS, Tzone, Email basic program from Tmoile...thanks alot- looking for something more stable, maybe faster WIFI, bluetooth those good stuff any recommandation would be great..and another question when i TRY to flash the fireware will i lose all of the data or program like the spb, theme and whether program thanks again sorry for all the question but i know you guys can help
I am using Rom- 1.8.10.2.WWE
ROM DATE-12/10/05
Radio Version-01.09.10
Protocal version-4.0.13.20
Extrom version 1.8.10.104
Not trying to be rude, but you really need to spend a week or two reading the threads in the "Wizard Upgrading" forum before you even thinking of flashing your Rom.
FYI firmware is for cellphones, Roms are for Windows Mobile Devices.
As to which Rom to use, that depends what you're looking for.
You can go for the latest, the most stable, or one that supports a specific feature. Again this is somethign you really need to read-up on. If you are looking for a specific feature use http://forum.xda-developers.com/search.php .
Honestly, you will gain speed and stability with any 2.x Rom.
To use one of the custom Roms you will need to CID unlock your device (search for it) first.
For your first flash you might just want to stick to an official Rom.
First, don't even think of attempting a CID unlock until you figure out if you have a G4 chip or not, unless you want to turn your MDA into a brick. There are other articles on the unlocking forums, as well as the Wizard forums that go into this in detail.
Until this is ironed out, I'd consider paying $40 to the guys at www.imei-check.co.uk. I've not heard any bad press about these guys, so if you want a SIM/CID unlock, go here.
If its freezing up on you, I'd consider backing your stuff on it, doing a hard reset, and restoring it. Make sure you have the data backed up (if ActiveSync doesn't have it, there are other backup utilities which can work well for your MDA you can purchase.) If you are getting freezes with just the factory installed stuff on it, you may have a hardware issue.
Lastly, quite a number of things can be enhanced/fixed without a ROM reflash, so unless T-Mobile USA comes out with new downloadable ROMs, I'd not worry about a reflash just yet.
hieu512 said:
Sorry, but i am a newbie i just got my MDA, it sometimes freeze up on me, so i talk to a friend he said try upgrading the firmware, so i wanted to upgrade the firmware just dont know which one cause there's so many...i wanted Tmobile USA, with all of the Tmobile programs such as MMS, Tzone, Email basic program from Tmoile...thanks alot- looking for something more stable, maybe faster WIFI, bluetooth those good stuff any recommandation would be great..and another question when i TRY to flash the fireware will i lose all of the data or program like the spb, theme and whether program thanks again sorry for all the question but i know you guys can help
I am using Rom- 1.8.10.2.WWE
ROM DATE-12/10/05
Radio Version-01.09.10
Protocal version-4.0.13.20
Extrom version 1.8.10.104
Click to expand...
Click to collapse
Sorry for butting in
Well i have this wiza200 tmobile MDA and would also like to Flash it because of speed and performance enhancement my question is when i flash a new rom will it make my phone again sim lock? because right now its already sim unlocked
my wizard came in with the stock rom any enlightenment will be greatly appreciated
Thanks
Hi all.
I've just got my new Orange M700 on contract and have a few basic questions before upgrading to WM6:-
1. Before upgrading is it sensible to backup the existing ROM etc? Are there tools to do this?
2. After upgrading SPL, GSM and ROM and presumably installing the latest UK network wizard software from HTC will the existing SIM just carry on working as before without Orange being any the wiser as to my actions?
3. In the case of a warranty claim or if I just want to go back to factory default for some reason, what's the recommended process (if any) of reverting to the original ROM etc?
I've been reading hundreds of posts here but thought it best to double check before proceeding. Could be useful for other newbies to see the answers to these questions as well I guess.
Thanks
good questions.....
the network manager is a good idea- wonder if there is one for the Aussie market??? Anyone?
from what i have read do a Hard SPL flash first in case of any problems.
No-one has yet extracted the Orange ROM for reinstallation. It is not a simple process! If you don't want to do it yourself, then there's no point in taking backups etc prior to a ROM update, because you can't go back Never try and apply a restore after a ROM update- you risk screwing things up big time!
Orange SIM's will continue working fine, and Orange will be none the wiser about the upgrade.
If you need a warranty repair, you will either have to hope someone has extracted the Orange ROM and posted it for download, or trust to luck that Orange will accept it as it is. A number of people have reported that they have successfully had a flashed device replaced, as long as the fault wasn't due to the ROM update itself.
If you are in any doubt, DON'T DO IT ! The differences from the Orange release ROM in the UK, and the cooked WM6 ROM's are pretty minimal, apart from the cosmetics.
Good info. Many thanks. Time to get flashing.
I'm in the process of dumping and rebuilding an Orange UK M700 ROM at the moment .... so hopefully I'll be able to upload it soon.
the only caution I would add is that you will loose access to the Orangeworld website after flashing, until someone can work out where Orange hide the files that identify the phone and allow the full graphics version of the site. Depends if thats an issue really
just to point out you can't upgrade to official WM6 for Trinity yet- the ROMS are cooked- i.e taken from other handsets and modified to work with Trinity hardware.
I tried many many cooked WM6 ROMS for the Prophet. All had pros and cons, but were too problematic to live with (e.g. wifi and BT setting vanishing, not reliably charging over USB etc).
I'll be waiting for an official WM6 ROM for Trinity - well here's hoping.
hollandg said:
I'm in the process of dumping and rebuilding an Orange UK M700 ROM at the moment .... so hopefully I'll be able to upload it soon.
the only caution I would add is that you will loose access to the Orangeworld website after flashing, until someone can work out where Orange hide the files that identify the phone and allow the full graphics version of the site. Depends if thats an issue really
Click to expand...
Click to collapse
Excellent. I was going to have a go myself but haven't managed to make the time yet.
Fingers crossed, good luck etc
Hi all,
I had an O2 XDA Stellar which I believe is the HTC TYTN II. However, this phone was stolen a couple of weeks back. I purchased a second hand one today which is sim locked to the orange network. I managed to break the lock by following the instructions on this link http://forum.xda-developers.com/showthread.php?t=433835. I followed the instructions word for word till step 5.
The problem is now though it accepts the SIM and I can dial out, I don't have any audio on the calls So I can call and my phone also rings when I receive a call but I can't hear the caller nor can I be heard at the other end
Also, I hate the orange rom (and I used to complain about the O2 rom) and I wish to use the default HTC WM 6.1 professional upgrade the problem again is that it asks for a serial number and my serial number starts with DCOxxxxxxxxxxx and it says that this is not a valid serial number
What do I do now? Has my phone become a brick Please do help I can't bear the thought of having one stolen and the other toasted by me
All help will be greatly appreciated
fmervin said:
Hi all,
I had an O2 XDA Stellar which I believe is the HTC TYTN II. However, this phone was stolen a couple of weeks back. I purchased a second hand one today which is sim locked to the orange network. I managed to break the lock by following the instructions on this link http://forum.xda-developers.com/showthread.php?t=433835. I followed the instructions word for word till step 5.
The problem is now though it accepts the SIM and I can dial out, I don't have any audio on the calls So I can call and my phone also rings when I receive a call but I can't hear the caller nor can I be heard at the other end
Also, I hate the orange rom (and I used to complain about the O2 rom) and I wish to use the default HTC WM 6.1 professional upgrade the problem again is that it asks for a serial number and my serial number starts with DCOxxxxxxxxxxx and it says that this is not a valid serial number
What do I do now? Has my phone become a brick Please do help I can't bear the thought of having one stolen and the other toasted by me
All help will be greatly appreciated
Click to expand...
Click to collapse
Did you actually read anything or did you just start hacking away ? I will cut and paste a few items out of that thread, so that you don't have to actually read it .
PLEASE READ THE *FAQ* BEFORE FLASHING OR ASKING QUESTIONS!!!
* IF YOU DONT NEED TO FLASH A NEW ROM THEN PROCEED TO STEP 6 TO PUT YOUR DESIRED RADIO BACK*
7. After I flash a Rom I dont have any sound in calls and the camera is black
The Radio has to match the version of Rom you flash i.e. WM6.1, an incorrect Radio will give sound and camera problems. Read The Ultimate Radio Thread to find a Radio that matches the Rom there are lots to try on there if one doesnt work then try another.
3. What are the different types of Unlock?[/B] (answer by DaveShaw)
The three stages of unlock are:
SIM: Allows you to use SIM's from another carrier. Can be done using codes or unlocker programs on xda-devs.
Security: Allows you to flash radios from another device - It does other stuff, but this is all the casual user will use it for
CID: CID unlocking is an old concept, nowadays you flash HardSPL instead. This lets you flash any ROM, Splash or Radio (depending on sec unlock) to your device. N.B. the CID is the carrier ID (e.g. HTC__001). The stock SPL's only let you flash ROM's that match the CID in the ROM image with the CID on your device.
Obviously you did not unlock your phone if a serial number is needed to flash a new rom. I would re read everything and do it again
Thanks for the reply
denco7 said:
Did you actually read anything or did you just start hacking away ?
Click to expand...
Click to collapse
As a matter of fact I did read that more than once.
denco7 said:
* IF YOU DONT NEED TO FLASH A NEW ROM THEN PROCEED TO STEP 6 TO PUT YOUR DESIRED RADIO BACK*
Click to expand...
Click to collapse
As you can see I'm a bit of a newbie here, so wasn't too sure if I did need to flash to a new rom. But I did anyway. And the call problems still remain
denco7 said:
7. After I flash a Rom I dont have any sound in calls and the camera is black
The Radio has to match the version of Rom you flash i.e. WM6.1, an incorrect Radio will give sound and camera problems. Read The Ultimate Radio Thread to find a Radio that matches the Rom there are lots to try on there if one doesnt work then try another.
Click to expand...
Click to collapse
I've been through this link as well and I was contemplating installing the latest version of the HTC WM6.1 ROMS (version 3.34.721.2, radio version 1.70.19.09) available at http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs However I was not sure if this would be ok and (at the risk of sounding extremely dumb) I was not sure what WWE stood for
denco7 said:
3. What are the different types of Unlock?[/B] (answer by DaveShaw)
The three stages of unlock are:
SIM: Allows you to use SIM's from another carrier. Can be done using codes or unlocker programs on xda-devs.
Security: Allows you to flash radios from another device - It does other stuff, but this is all the casual user will use it for
CID: CID unlocking is an old concept, nowadays you flash HardSPL instead. This lets you flash any ROM, Splash or Radio (depending on sec unlock) to your device. N.B. the CID is the carrier ID (e.g. HTC__001). The stock SPL's only let you flash ROM's that match the CID in the ROM image with the CID on your device.
Obviously you did not unlock your phone if a serial number is needed to flash a new rom. I would re read everything and do it again
Click to expand...
Click to collapse
I maintained the default that was given by the unlocker for the CID (I think all zeros). Do I have to change this as per the ROM image? I don't mind re-doing this again it's a relief that my device isn't busted
No your phone isn't busted. Go into bootloader and check what it says next to spl, if you followed Mark's steps, it should say 3.29 Hard. If that is what it says ,then you can flash any Kaiser rom you want. If it doesn't then start over again.
WWE stands for World Wide English and those roms are all in English. That rom you picked will be fine, if you do not wish to explore the fine world of custom roms ? Maybe later.
You only have to CID unlock once by following the steps, not at every rom flash.
No sound means wrong radio, 6.0 roms need 6.0 radios and 6.1 roms need 6.1 radios. If the rom has a radio in it already then flash away.
Thanks Denco Flashed the ones I mentioned and it works perfect. Can't believe I actually have a working device Thanks for all your help, really great.
Now to sync my data to my new (second hand) htc and I'm good to go
Another question, the device works fine, however since it is a HK rom, it seems to have localised to HK. I've changed this as much as possible to UK. However, I'm wondering if this will affect anything else? For example the gps? Is there any quicker way to configure this globally so all settings use UK instead of HK?
Why didn't you flash the latest UK ROM.
Use this code: HT750GB02264 to download from HTC's site.
fmervin said:
Another question, the device works fine, however since it is a HK rom, it seems to have localised to HK. I've changed this as much as possible to UK. However, I'm wondering if this will affect anything else? For example the gps? Is there any quicker way to configure this globally so all settings use UK instead of HK?
Click to expand...
Click to collapse
Once you are unlocked and HardSpl'd you can flash any rom you want. Pick a UK one another WWE rom or a custom rom. Test a bunch until you have one you like. Your only restriction is it has to be a Kaiser rom. And with all the Kaiser roms available, it is not a restriction at all.
Mister B said:
Why didn't you flash the latest UK ROM.
Use this code: HT750GB02264 to download from HTC's site.
Click to expand...
Click to collapse
Wow, thanks for that, I was looking for a valid serial through which I can download from the htc uk site One question I had is do I install the radio which I download from htc? Or do I keep the one I have already flashed? The one I have flashed yesterday seems to be a later version than what I've downloaded from htc
denco7 said:
Once you are unlocked and HardSpl'd you can flash any rom you want. Pick a UK one another WWE rom or a custom rom. Test a bunch until you have one you like. Your only restriction is it has to be a Kaiser rom. And with all the Kaiser roms available, it is not a restriction at all.
Click to expand...
Click to collapse
1. I keep hearing on this forum about Hard SPL, I'm not sure what this is used for or why it is required but I followed the instructions and it seems I had installed JumpSPL1.56-KAIS.exe. Now, since then I had flashed the rom, so do I need to reinstall this again? Is there some other one I should be using? I come across different versions on some threads. Also, how can I check the version of HardSPL I have?
2. When I view the memory (under settings) it shows me Storage and Program. However, I can't seem to see any storage area in file explorer. I know in my old xda 2i, there used to be a separate storage area. The reason is because some of the apps I install are quite bulky for example lexisgoo english dictionary (the dictionary files themselves are about 18mb) and this fills up the main memory. How can I install this in the storage memory? (not storage card since I sometimes swap storage cards)
Sorry lot of questions I know, but I'm a newbie and all help will be greatly appreciated
The UK downloaded ROM will install the radio too.
I would do a bit of testing with your current set-up, then flash the UK ROM.
Test the new UK ROM & radio & then reflash the radio only if you want (do some searching on Radio versions)
Newer versions are not always best, chasing the latest builds normally bites you in the ass at the end of the day.
Check HardSPL by going into bootloader:
* Using a stylus, press and hold the soft reset button at the bottom of the phone along with the camera button
* Release both buttons once the bootloader screen appears
* Exit bootloader by pressing soft reset button
Once you have installed HardSPL thats it, job done (you installed it during unlocking)
What you see in file explorer regarding storage is correct: 128MB RAM for running software ect & 256MB ROM for storing your programs ect (WM2003SE was different)
ROM can be increased by using one of the cooked lite ROMs if storage space is a concern.
Mister B said:
The UK downloaded ROM will install the radio too.
I would do a bit of testing with your current set-up, then flash the UK ROM.
Test the new UK ROM & radio & then reflash the radio only if you want (do some searching on Radio versions)
Newer versions are not always best, chasing the latest builds normally bites you in the ass at the end of the day.
Click to expand...
Click to collapse
Will do, the HK version seems very stable, the only thing that bothers me is the region settings. Anyway, I think I'll give the UK Rom a go and if that works well I'll stick with it
Mister B said:
Check HardSPL by going into bootloader:
* Using a stylus, press and hold the soft reset button at the bottom of the phone along with the camera button
* Release both buttons once the bootloader screen appears
* Exit bootloader by pressing soft reset button
Once you have installed HardSPL thats it, job done (you installed it during unlocking)
Click to expand...
Click to collapse
I checked the version and this is what it showed:
KAIS130
SPL-3.2.9.Hard
CPLD-8
Click to expand...
Click to collapse
TBH, I don't know what any of that means But do you think the version I have is ok, or do I need to upgrade this to some other version?
Mister B said:
What you see in file explorer regarding storage is correct: 128MB RAM for running software ect & 256MB ROM for storing your programs ect (WM2003SE was different)
ROM can be increased by using one of the cooked lite ROMs if storage space is a concern.
Click to expand...
Click to collapse
I've attached a screenshot of my memory screen. The bit that puzzles me is that the storage area apparently has a lot more storage but I do not have an option to install all my applications on that area or atleast the bulky ones. I don't think I need a lite one since I do have 112MB free in the storage area which is more than sufficient for all the apps I usually install. Can you advise how I can install apps to the storage area as well?
Lastly, I was wondering if it is possible for me install my apps on the rom and then kind of take an image of my setup and flash the rom with this setup. That way when I do a hard reset, all my apps are installed again. Which will save me the trouble I know sprite backup does something like this but I'd prefer if it was in the rom
Thanks for all your help, it has given me a lot of confidence in these matters. Something I probably wouldn't have attempted
Mister B said:
Test the new UK ROM & radio & then reflash the radio only if you want (do some searching on Radio versions)
Newer versions are not always best, chasing the latest builds normally bites you in the ass at the end of the day.
Click to expand...
Click to collapse
I agree 101% and it appears fewer resources are put into ironing out bugs in the WM 6.1 ROMs than the WM 6.0 ones. I replied to fmervin's post in the ROM forums along these lines.
If all is running OK I would stick with your current HardSPL.
When installing your applications choose the option of installing to "Device"
You could install all your apps into a ROM, this would be cooking a ROM & is a complex process.
I would suggest a backup via Sprite or SPB. I use SPB v2.0 build3065 & it works well for me, preference of backup software is a bit of a Marmite scenario, you either love it or hate it.
Lastly, I was wondering if it is possible for me install my apps on the rom and then kind of take an image of my setup and flash the rom with this setup. That way when I do a hard reset, all my apps are installed again. Which will save me the trouble I know sprite backup does something like this but I'd prefer if it was in the rom
Click to expand...
Click to collapse
You can't do that, it is flash memory. It's not like you can partition the hard drive.
But this is the easiest way to get your Apps and settings back after a flash.
Try this Sashimi Auto installer by a former XDA member. It is a nice little program that installs all your apps after a flash
http://www.winmo-experts.com/viewtopic.php?f=7&t=4
Help Please
Hey Denco..Than'x for considering my thread & giving out suggestion towards the link to check the info. But i m really nt that techy afterall so i can burn a ROM on my Tytn II. Even though i tried to burn a RUU rom that supports TyTN II ..Its just gets disconnected from USB mode..So i was looking forward to start it initially with some comparatively easier to install .cab files..Can't these RUU files be transformed into .cab files or maybe some other version of Manila 3D cab file that is completely fixed...I seriously have done a lot of research upon this but nothing looks like working. So please if you have some links to .cab files that can give a better & different look to my Kaiser running Windows 6.1...It'l be a great help !!
Than'x & regards in advance
vicky_crispy said:
Hey Denco..Than'x for considering my thread & giving out suggestion towards the link to check the info. But i m really nt that techy afterall so i can burn a ROM on my Tytn II. Even though i tried to burn a RUU rom that supports TyTN II ..Its just gets disconnected from USB mode..So i was looking forward to start it initially with some comparatively easier to install .cab files..Can't these RUU files be transformed into .cab files or maybe some other version of Manila 3D cab file that is completely fixed...I seriously have done a lot of research upon this but nothing looks like working. So please if you have some links to .cab files that can give a better & different look to my Kaiser running Windows 6.1...It'l be a great help !!
Than'x & regards in advance
Click to expand...
Click to collapse
I think you need to decide what it is that you want to accomplish. Unless you cook your own rom, there is no way to add apps to the rom ( so that they will remain after a hard reset) Your rom is wyour phone's base operating system, it contains your OS (WM 6.1 ) and can only be replaced after completely erasing and replacing all files from the previous rom.
If it is a new rom you want, pick a rom that interests you and follow these instructions verbatim .
http://forum.xda-developers.com/showthread.php?t=433835
Your phone will go to the bootloader screen ( three color) and it will disconnect from usb during the process, but be patient until the end. When it says it takes ten minutes, it takes ten minutes. Leave the room if you have to , to keep from getting impatient.
If you just want to keep your OEM WM 6.1 and keep it simple, but change the look of your phone try this,
http://www.htcwiki.com/page/Manila+2D+and+M2D+Themes
This will change the look and feel of your phone with uninstallable .cab files and will not affect the rom or brick your phone by accident.