Everytime i insert my card it asks me if i want to format it to make it readable? - even though i formatted it in my computer. Also i cant write anything to it when my 8125 recognizes it in a slot. The cars is SanDisk so it should be a good quality.
I'm using a 2GB SanDisk card with no trouble at all. I _didn't_ format it on my PC but rather used it straight out of the box.
Do you still have the same message if you let the 8125 format the card?
i tried doing that and it says that the phone cannot recognize the card.... the weird thing is that the card goes in crooked and the fit isnt perfect i have to push it in hard.....
Quite a few people reporting a problem like this - seems to be fixed with sktools or storage tools (google them demos allow you to format - install on device) and format card on device to fat16.
meschle said:
Quite a few people reporting a problem like this - seems to be fixed with sktools or storage tools (google them demos allow you to format - install on device) and format card on device to fat16.
Click to expand...
Click to collapse
I have the same problem before, i tried to format it to fat16 and the 2gb minisd was recognized as 1gb instead of 2, tried every solution from getting compatible version of a card reader to re-format using fdisk via DOS., Called the manufacturer and they we're happy to replace it. They advised that it should be re-formatted as fat only and not fat16 via DOS using the card reader.
good to know as i just bought a 2gigger.
The problem is that you formatted it on your PC. USe SKtools to format it on your device and you should be all set. I think the demo version of SKtools allows you to do this stuff.
i use my 2 GIG since i bought the phone almost 4 months ago without any hassle.
Just used the card out of the box without formatting it.
This issue is reported several times and is caused by using a not compatible cardreader on the PC to format the card.
A lot of the (even usb 2.0!!) cardreaders is not capable of reading over 512MB memory cards. If you use a 1Gb or 2GB card on such a reader it will probably say the card is not formatted. WHEN you do format the card using that reader, you wil make it unusable.
:arrow: Make sure you format the card via a compatible cardreader to avoid this.
:arrow: If you get a 'card not formatted' message, try to read from / write to it in your device first (before attempting to format)
Just got my 2GB card....MDA won't read it.
Camera won't read it.
PC can read it. It was Fat32, I reformatted it to Fat...still a no go in the phone or camera, but works on the PC....what gives?
Just got my 2GB card....MDA won't read it.
Camera won't read it.
PC can read it. It was Fat32, I reformatted it to Fat...still a no go in the phone or camera, but works on the PC....what gives?
I have a SanDisk 2Gig card. It worked fine right out of the package. Haven't had any problems with any of the ROMs I've run on my 8125.
-Scott
my 2GB card works fine, except for the fact that it's stuck in there.. i need to tak it apart and fix the spring loaded latch somewhere in there..
I got a 2GB from Amazon: OEM 2GB MINISD Mini Secure Digital (SD) Card but it did not work on my Cing 8125.
TopRam
I have been using a 2GB miniSD made by TopRam. Works in the 8125 and with my USB card reader no problem since day one. 8125 recognizes the entire 2 gigs (well minus just a few bits...about 99% of the card). Got it off eBay while I was waiting for the phone in the mail. Never needed formatting or anything..worked straight from the package. I was a little worried at first that it wasn't one of the "well known" brands of cards, but there have been no problems whatsoever.
I'm using the Transcend 2Gb 80x MiniSD. Works like a charm.
Keep in mind that SLC flash chips (mainly made by Samsung and a.o. used by Transcend and Mobymemory) have longer lifetime, are faster and consume less power than MLC flash chips. Disadvantage is that SLC is more expensive. Bought my 2GB for approx 62 euros.
Related
Performing WizBackup successfully, resulted in an un-readable mini-SD card!!!!
http://forum.xda-developers.com/viewtopic.php?t=53132
Got this A-data 2 GB card of the net for a good price, but I don't like throwing 60 bux out the window!!!!
The card worked perfectly fine until the programming steps where the instructions start writing data from the phone to the memory card, I noticed after that point the card did not show up under file explorer on the 8125.
The data wrote fine, the software continued on, and even copied the data from the card to my PC, but after that this card has not been readable.
I do not have a card reader for my PC.
Any suggestions on how to fix this?
I have already attempted to use a tool on my 8125 to format the card (SpTaskManager) and it does not recognize the card either.
At this point I'm wondering if I can use a terminal service program over USB to fix the card. (seemingly the same way it was screwed up).
I sincerely appreciate any help or links, or resources into fixing this 2gb corn flake!
Thanks!!!
Well I ordered a card reader, and another 2gb card from NEW EGG this time.
I'll try the card reader instead, but I appreciate any other solutions or advice you guys have to offer.
Atleast this time if I have a card problem New Egg is usually good to deal with.
I don't think it is a hardware problem though, it's probably something wrong with the software on the card.
I don't know alot about mini sd cards, but I'd guess something similar to the MBR on a hard drive got erased.
Just an update, I also downloaded a trial version of pocketpc mechanic, and it doesn't see the card at all either.
UGG! Waiting for my other stuff from New Egg.
Same problem here...got the 2GB miniSD off ebay. It was new, or at least it looks like new packaging...but I can't get anything, SKTools, Storage Tools, card reader, camera, MDA to read the card.
Do I need to upgrade the ROM? Is 2GB too much for a miniSD?
I and many other people here have 2 gb cards so that is not the issue. What probably happened is that your card died. I had this happen to a Kingston card after only 2 weeks. They replaced it for free and even paid the shipping. There is really nothing else you can do once the card is dead. I learned the hard way to backup not just to the card but to the PC also.
TMO customer service says my ROM won't support more than 512MB. I'm still running the stock 1.2 that came with it.
Getting ready to try the ROM upgrade....hold your breath......
Hi,
Does XDA2i support 1G SD card? I tried but it doesn't show up in the explorer.... Can someone help? Many thanks!!
bennykmh said:
Hi,
Does XDA2i support 1G SD card? I tried but it doesn't show up in the explorer.... Can someone help? Many thanks!!
Click to expand...
Click to collapse
1 GB Dane-elec Xs work fine on my Qtek 2020i(XDA2i)
you may format card before use
I have you tried any other card in your XDA IIi.
I have a DANE-ELEC 1 GB SD card and a INOV8 512 MB cards
and both work well.
Sorry I can't be of more help
Muzza
Kingston 2 GB (30651-001.A00LF p799861x01)work as well,
maybe i should have purchase a 4 GB :wink:
Scandisk 1GB SD card working fine!
transcend 2gb 150x absolutely fine work =))
maybe you have bad card? or maybe format it via cardreader can help..
My Kingston 2GB works great on the device, might be a case of a bad card for you, tried it on any other devices?
Worked
I use Kingston 1Gb SD card... 50x and it works fine... maybe your battery is dying
I think theres still a 4gb SD card at work which I'll give a go tomorrow if I get a chance.
I work at CeX in Brighton, England, and we get a lot of different types of memory cards in. So far I'm just using a standard SanDisk 512mb card, but will eventually get a 2 or 4gb (the 4gb we have is £120 >.<)
Kingston SD Card 1GB works fine on my XDA IIi. What brand do you use anyway?
XDA IIi definately supports up to 4gb (150x) cards.
I just got a "Topram' 4gb 150X...despite formatting both via card reader and my device it will not read...
Does it show the card size in the Memory cp? Or can you just not transfer files to and from it?
neither...as soon as I insert it into the 2i I am asked to format it to make the card ledgible...so I agree...but it still does not show up at all. Neither in memory size menu or file explorer.
I have formatted it via card reader on the compeuer too...It accepts files via card redaer so the card itself is ok.
But every single time I insert it into the PDA it asks me to format it again and it never shows up.
bit off topic but as anyone else had a problem with SD/MMC cards working for a while (sometimes as little as 6 months other times over a year) then totaly stopping ie show as not being there in any card reader, only to come back to life after about 12 months stuck in a draw. I have had this with 2 cards so far and got 1GB card in the draw at the moment which stopped working just as I put some important files onto it
SD Cards
I have a 4GB Transcend, 2GB SanDisk and a 512MB Unbranded and they all work perfectly fine in my xdaIIi, maybe your card reader is a bit iffy?
EDIT: By card reader I mean the bit that you insert the card into the xdaIIi
It may simply be certain makes of cards that work, and certain that dont. All you can do is hope the retailers let you try before you buy
Tom Swinnen said:
Scandisk 1GB SD card working fine!
Click to expand...
Click to collapse
i also have a SanDisk Ultra II 1GB in mine
XDA 2i - SDIO size - does anyone tried 4G?
Hi,
I want to buy 4G SD card to my XDA 2i, but I would appreciate if someone can tell me if he succeeded to work with 4G card.
10x
Dror
light said:
I just got a "Topram' 4gb 150X...despite formatting both via card reader and my device it will not read...
Click to expand...
Click to collapse
erm... u made sure u formated them as FAT not FAT32? i had no end of probs with my 2020 when i did that, and the 1gb unbranded card i have in my 2020i is FAT and works fine, as most hand helds and camera (i use it in my konica/minolta SLR digital, it hates FAT32 file systems too) format them as that and jobs a good one!
Got A-Data 4gb card yesterday and it worked initially until it started to look strange when I was transferring big files unto it. Seems like I couldn't end the transfer and on it appeared a catalog named xxxxxxx.xxx. I disconneced tilt during this transfer and neither tilt no Dell 1420 with SDHC reader can see this card anymore. Nothing happens at all when I plug it in. I hoped that reformatting will work but Dell doesn't see card even in disk management tools (Vista). Regular size SDHC card is read by dell just fine.
Card hardware failure or filesystem problem? Thanks!
I have experienced this issue as well with both a 2GB and an 8 GB card. I have noticed the corruption mostly happens when I take the cards out to transfer big files using a USB reader. Do not touch the surfaces of the cards, handle them by the edges to minimize the risk of losing your data.
Thanks, I will remember that but if card is not seen as a drive by PC can I still return it to workable state?
You will likely have to format it with FAT32. Obviously your data will then be toast (but in all fairness it probably already is). If you can't format it then you need to google for memory card data rescue utilities. If none of these suggestions pan out, I would start the warranty procedures with the manufacturer to get it replaced.
Hope this helps!
Hopefully an easy question for someone to answer! Will the Kaiser read a SanDisk 8GB MicroSDHC card?
On another point, I have a 4GB MicroSD that no device can read anymore. I cannot reformat it as it does not show up on the device (PC, PDA or anything!). Any ideas?
gregwhitehouse said:
Hopefully an easy question for someone to answer! Will the Kaiser read a SanDisk 8GB MicroSDHC card?
On another point, I have a 4GB MicroSD that no device can read anymore. I cannot reformat it as it does not show up on the device (PC, PDA or anything!). Any ideas?
Click to expand...
Click to collapse
1. yes
2. ??
1. Thats what I have
2. Broken card, throw it away?
Hmmm
1. Been running that for a while.
2. Make sure your PC Reader can support MicroSD before deciding that the PC can't read it (hint - putting the microSD card into the Sandisk larger shell does NOT make it a regular SD card). If you are POSITIVE your computer can read a MicroSD card, and it doesn't register, then toss the card.
jdmba said:
2. Make sure your PC Reader can support SDHC before deciding that the PC can't read it (hint - putting the microSD card into the Sandisk larger shell does NOT make it a regular SD card).
Click to expand...
Click to collapse
Corrected above - the adapter DOES turn a MicroSD into an SD, AND a MicroSDHC into an SDHC. But, not all readers can read the HC cards (4GB and more).
gregwhitehouse said:
Hopefully an easy question for someone to answer! Will the Kaiser read a SanDisk 8GB MicroSDHC card?
Click to expand...
Click to collapse
This has been asked many times and the answer remains yes (the same for the 16 GB version - I use one with my TyTN II).
On another point, I have a 4GB MicroSD that no device can read anymore. I cannot reformat it as it does not show up on the device (PC, PDA or anything!). Any ideas?
Click to expand...
Click to collapse
When you say 'anymore', whats changed? Are you still using the same microSDHC -> SDHC adapter that the card came with and a suitable SDHC compatible reader when testing it on your PC? If so, it's time to get in touch with the company that sold it to you for a warranty claim.
I had a similiar problem. While moving some music over to my 8 gig SD brand card it failed after about 3/4 of the files and then dissapeared. I've tried soft reseting and popping the card in and out and I can't get my phone to recognize it.
I need to get a new usb adapter b/c the I don't think the one I have is hc compatable (it's a few years old) so I have no idea if my computer will recognize it directly. Does this sound like a card issue or phone issue.
Running ATT WM6.1 minus bloat with a few programs (all of which have been running for a week or so no problems). Sorry to hijack, I just didn't want to open a new thread and get flamed.
i got a 4gb micro SDHC, its a sandisk. i got it to upgrade from my 2gb sd, i have read that the HC cards (sorry if the card is in the acronym) are compatible with tytn II's.
it wasn't with my original rom, and now i have tried to new roms both of which wont recognise it at all. is there anything i can do?
patriotaus said:
i got a 4gb micro SDHC, its a sandisk. i got it to upgrade from my 2gb sd, i have read that the HC cards (sorry if the card is in the acronym) are compatible with tytn II's.
it wasn't with my original rom, and now i have tried to new roms both of which wont recognise it at all. is there anything i can do?
Click to expand...
Click to collapse
I have 4GB sandisk sdhc card in my Kaiser and its working withot problem.
Did u try to format the card using fat32?
I just put a 16 gig Sandisk in mine last week I found on Amazon.com for about $65. Works fine.
Mack
New owner of Kaiser,I had Artemis and Touch so far,now I want to buy 4gb micro SD card (made by Kingston) for Kaiser, Has anyone had any problems with 4gb miscro SD?Will it work smooth and without any problems?
Thanx in advance
Greets from Serbia!
Since this morning my device is telling me that no Storage Card is inserted. I didn't change anything and the SD has been inside the device all the time. I bought the device around april 2008. I still have to test the card on my PC at home, but I wanted to check what my chances are. What is a bigger change? That the SD card just died on me or that my device has a hardware problem?
Funny thing is that yesterday I flashed to a diffrent ROM. I did a hard reset, still no luck. Flashed with an entirely other ROM, still no luck. So I am hoping its just the SD card that broke. Would be strange if flashing a ROM would cause the SD card hardware inside the device to fail the next day.
gochem said:
Since this morning my device is telling me that no Storage Card is inserted. I didn't change anything and the SD has been inside the device all the time. I bought the device around april 2008. I still have to test the card on my PC at home, but I wanted to check what my chances are. What is a bigger change? That the SD card just died on me or that my device has a hardware problem?
Funny thing is that yesterday I flashed to a diffrent ROM. I did a hard reset, still no luck. Flashed with an entirely other ROM, still no luck. So I am hoping its just the SD card that broke. Would be strange if flashing a ROM would cause the SD card hardware inside the device to fail the next day.
Click to expand...
Click to collapse
Try to reformat the sd card with fat32. That helps sometimes.
Mikulec said:
Try to reformat the sd card with fat32. That helps sometimes.
Click to expand...
Click to collapse
My laptop has a SD reader but it doesnt even map the card to a drive like it usually does. Any tools that I can use?
I already ordered a 8 gig MicroSD which should arrive tomorrow.
I'm not ready to blame my Tilt for my mSDHC problems but it sure seems like theres a lot of posts out there here and other places about people having memory card problems with their Tilt. I"m going to try again but if another memory card fails I'm sending my tilt back and hopefully I can demand to at least upgrade to a Fuze for a cost.
Funny this thread came up as my 4 gig card crapped out on me recently and is unrecogniseable to any device after running the sdhc cab on it. But yea, 8 gig works just fine. Using a 16 gig now with smooth sailing
Hi, I purchased the Transcend 8GB Micro SDHC TS8GUSDHC6 about 3-5 Mo ago, for my AT&T tilt/8925, The issue I am having is that after about 1.9Gb, has been written to it, the transfer will either fail, or it will just sit and the completion will raise indefinitely. I do not have a SDHC compatible reader for my Pc, nor do I have another card over 2Gb. I was wondering if the phone cannot address over 2Gb, or if there may be something wrong with the card?
Hy
maybe i ma wrong, but i think you must format the card in "FAT 32". if you formated the card in "FAT" you can't get it over 2 GB... i don't it for sure
Greets, DrWinston
drnoobfragger said:
The issue I am having is that after about 1.9Gb, has been written to it, the transfer will either fail, or it will just sit and the completion will raise indefinitely.
Click to expand...
Click to collapse
If you are attempting the transfer using Activesync:
You are very patient
Activesync is incredibly slow for large file transfers
Activesync has a bug where it appears file transfers are starting again continuously even though they do go through (eventually).
If you don't have a compatible card reader and have not partitioned the card, it should have already come with a Fat32 partition so DrWinstons concerns shouldn't be an issue. If you've put it in another (old) device to wipe it though, this may well be what's happened. Where has the card been?
The card was bought for this phone, and has only been in it. as far as active sync, it will write 1.5gb in about 35-40 min, then if I try to add another 1.5gb file, it will say 35min and count down for a few minutes, then suddenly the transfer bar, seems to stop and the timer goes up to over 2Days, and will continue to raise, I have left it for 10Hours one night and it made it no further.
Update, I am formatting with pocket mechanic now, Fat 32 4k cluster Low level, Backup Fat
Update2 Well format failed, now the card cannot be read by the OS, I am going to RMA the card. Guess that will fix it
1. I have encountered the same problem and rectified with an SD reader. My SD reader works for SDHC 8GB card. So perhaps if you can find an SD card reader, try it.
2. As for formatting with pocket mechanic, it doesn't seem to work for me as well. What I did was to use error correction in Win XP using the SD card reader. This worked for me.
3. You could also try downloading some usb host software bypassing ActiveSync totally and use your 8GB card like a regular flash/thumb drive which should dramatically improve your file transfer time.