BlueAngel BootLoader - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Hello Everyone,
My BA is stuck at the Splash Screen, I suspect that the Bootloader is corrupt. Does anyone know how to flash it?

try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
imatrix

imatrix's suggestion.
@imatrix
Followed the steps before, and followed them again.. I'm still stuck.
Something interesting happened though:
There are two horizontal stripes across the splashscreen now.
I already tried to flash the OS, It doesn't work with the standard imate flash executable (It used to work before) and now I'm getting a 'MODEL ID ERROR' when I try to flash it using the BAupgrade... executable.
I tried with the MAupgradenoid tool, it flashes but I still get stuck on the splashscreen...
Thanks,
Wadih

BlueAngel Bootloader
Anyone has a way to either dump a bootloader file for the BA (Providing the file of course) or alternatively directives to copy it from another device (From the same make, i.e. Imate PDA2K) ?
Many thanks,
Wadih.

try this
http://forum.xda-developers.com/viewtopic.php?t=49611&highlight=model+id+error
imatrix

@imatrix
imatrix said:
try this
http://forum.xda-developers.com/viewtopic.php?t=49611&highlight=model+id+error
imatrix
Click to expand...
Click to collapse
I did, but as I specifed in me earlier post, eventhough the MAUpgradenoID flashes the files, I still get stuck at the splashscreen.
Interesting point: After flashing witht the MAUpgradenoID, I try reflashing back with the BAupgradeid.. I get the Model Error ID error back..
Something in the BA is wrong, and I believe it may be in the Bootloader. So, is there a way to replace the bootloader itself?
EDIT: By the way, I can't seem to be able to place a WM5 rom instead of the WM2003, although the flashing procedure starts, it quickly ends (i.e. without the percentage bar appearing) and says that the flashing worked successfully... But nothing gets actually flashed.
Many thanks for the help imatrix.
Regards,
Wadih.

hey,
check this out http://buzzdev.net/component/option,com_remository/Itemid,100/func,select/id,38/
but i have to warn you, replacing a booter is very dangerous, anything goes wrong during process will kill your device. so please handle with care.
imatrix

@imatrix
imatrix said:
hey,
check this out http://buzzdev.net/component/option,com_remository/Itemid,100/func,select/id,38/
but i have to warn you, replacing a booter is very dangerous, anything goes wrong during process will kill your device. so please handle with care.
imatrix
Click to expand...
Click to collapse
Thanks for the link, but how do I copy/get a clean boot bin file? (Which app, syntax, etc...)
Cheers,
Wadih.

BlueAngel froze on isalling wm6.5
much respect 2 all.I'm new here.i tried installing wm6.5 on my Blue Angel i tried putting it on a memory card i pressed power reset hold Camera and Record no luck. i didn't noticed this rom is for the Touch Diamond.i opened the file in the memory card and there was many files.i installed a few files i clicked one file and it froze.what i got is message serial on the top the screen and on the bottom of the screen is v1.02.i also tried sync it with computer no luck.can some one please help me and direct me 2 get wm6.1 because when Blue Angel 6.5 i was directed for the Touch Diamond rom.much respect.thanx a million thanx in advance.lol.
---------------------------------------------------------------------------
Learn 2 live & live 2 learn.learn 2 listen & listen 2 learn.Live 2 love & love 2 live.
We live 2 die & we die living.
life is what u make of it

BlueAngel froze on installing wm6.5
much respect 2 all.I'm new here.i tried installing wm6.5 on my Blue Angel i tried putting it on a memory card i pressed power reset hold Camera and Record no luck. i didn't noticed this rom is for the Touch Diamond.i opened the file in the memory card and there was many files.i installed a few files i clicked one file and it froze.what i got is message serial on the top the screen and on the bottom of the screen is v1.02.i also tried sync it with computer no luck.can some one please help me and direct me 2 get wm6.1 because when Blue Angel 6.5 i was directed for the Touch Diamond rom.much respect.thanx a million thanx in advance.lol.
---------------------------------------------------------------------------
Learn 2 live & live 2 learn.learn 2 listen & listen 2 learn.Live 2 love & love 2 live.
We live 2 die & we die living.
life is what u make of it

100/100 work
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
imatrix
Click to expand...
Click to collapse
thaks br very good

Hi, I have the problem, that windows does not recognize the Blue Angel any more, so no "WCEUSBSH001" available. Any help??
Thx

Related

If you stuck on boot or color screen !

Guys,
This is my experience with O2, which stuck on boot after udated to new IVAN's ROM.
First of all I'd like to thank Ivan for his great job.
Now, what I did:
Downgraded to se2003
Unhide, Unlocked EXTROM
Repartition EXTROM to 8MB
Upgraded to new WM5 ROM
Reboot -> STUCK !
I found the solution which worked for me and may be will help you too.
More, after my second attempt to upgrade ROM, my Laptop rebooted itself a 47% ! I did panic- my device was gone dead!
even Bootloader mode was unavailable.
OK, I disconnected PDA from cradle, removed battery and left it for 10 minutes. Then I put battery back, and was able to put it into bootloader mode.
Then, I run mtty utility and typed in "set 14 0" I'm not sure why and how, but it allowed me to to go to bootloader mode.
-I set SE2003 OS
-I repartition EXTROM to 16MB
-Updated again to new Ivan's WM5.
Voila ! it's OK now. I'm installing all needed CAB's and now have clean very fast and working OK WM5 OS o my O2 XDAs PDA.
( although have not tryed yet BT and WiFi)
I'm afraid the problem was due to setting number 8000 KB in partiotion tool set it actually a bit less something about 79xx KB.
May be EXTROM for Ivan's ROM did not like it and failed to boot. But this is just a speculations, I'm not sure. I should perhaps set size o EXTROM to say 9000KB and try again, but simply did not have a time to do test.
Nevetheless, I'm happy now.
can u provide me step by step (noob guide) to downgrade back to wm2003se ... the one i downloaded from the official site doesn't work ... it will say error and i still stuck with wm5 ... im a noob ... please really help, thanks
ok at last i found it ... extract the installation files provided by o2 ... put the rom file into the downgrade folder provide by the modified rom pack ... now i try go back to wm5 ... wish me luck
i tried go back to win2003se but when i use the unlocker tools it failed ... so i guess i will nvr get to see the ext rom ... anyway as long as the phone can be use i will leave it as it is now
Yes, I know, it gives you an error message (something about wrong parameters) on unlock. But, under that you can see another message box with unlock OK message. Quite weird.
Steps I took to downgrade are exactelly as instructions in downgrade folder.
And one more thing I forgot ! After unhiding I did soft-reset, then unlocked and then Formatted ETROM folder before upgrading to WM5.
COM said:
And one more thing I forgot ! After unhiding I did soft-reset, then unlocked and then Formatted ETROM folder before upgrading to WM5.
Click to expand...
Click to collapse
maybe that's why u able to see the extrom after upgraded to wm5 ... btw i install the cabs one by one and now my wm5 worked ... guess imnot going to touch it anymore, but the performance is actually quite slow ... do you actually install all the cabs into the device, storage card, or extrom partition (i dont have this) ... to maximise the performance?
what WM5 are you using?
if you ask me, i'm using Ivan's ROM + radio 15.0 with about 10 diff. cabs installed.
performance is not such impressive, but everything is working and I do not have soft I won't use.
clean and quite reliable, but speed is slow.
COM -
I also got stuck with a white screen after flashing ArtZ Rom and doing a hard reset.
Just a white screen and nothing happens.
Flashed other Roms - back to Tuma - same thing - white screen after hard rebooting.
Stuck and confused now.
Any ideas for a solution?
Thnx
OK - I am back.
Panic mode over - whew!
Flashed back to WM2003 from i-mate site - it worked.
Then flashed to latest ArtZ Rom.
Don't really know what happened or why. I've upgraded to nearly every WM5 Rom with no problems. suspecting the partitioning of extrom?
hasanj4 said:
OK - I am back.
Panic mode over - whew!
Flashed back to WM2003 from i-mate site - it worked.
Then flashed to latest ArtZ Rom.
Don't really know what happened or why. I've upgraded to nearly every WM5 Rom with no problems. suspecting the partitioning of extrom?
Click to expand...
Click to collapse
I am still in the same problems. I can't downgrade to
Windows SE2003, becouse of error 113: "Extended ROM
Update Error". Stucked in white screen and, after reset
at 3 stripe-colored-screen.
Does anybody know the solution for this issue ?
Thank you in advance.
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Sam
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Sam
Click to expand...
Click to collapse
---
imatrix, thank you very much, your hint solved
this issue with stucked boot screen and Extended
ROM Error when downgrading to SE2003.
I already tried with mtty and "SET 14 0", but
don't know for the other commands / task 28, task 0.
The main hint is "task 28" which made DOC_format_HW+
DOCInfoTableinitHW+ other formatting.
Again, thank you very much and all the best to you.
Greetings from Croatia, the small land for a great vaccation ;-)
@MDA3_CRO
Just saw your post.
Could not get mtty to work.
Will keep your instruction for future use (hope not).
Glad your .paper weight' is useful now
Please help I have tried all the above and none of it has worked, I'm still stuck in bootloader screen.
i dont understand what you mean by
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
when i run my mtty it just opens "Open Port Settings" then it goes to a window that shows i can type in it but it only allows me to copy paste words into it. Can anyone help me please?! i just want to be able to use my BA again

any Professionals here. Where is my Extended Rom ?

Hello All,
I have PDA2k. I (formated my Extended Rom to 128 KB) to upgrade to WM5 by logout everything was fine but I used DOC_Repart under this copy of WM5 it opend but when I formated it The phone didnt open (Stuck on the boot) I downgraded to WM2003SE and when i try to unlock the Extended Rom I got this error
Code:
ERROR: Open - The specified network resource or device is on longer avaliable
when I tried to format under WM2003SE I got this error
Code:
Create handle failed
ANY SOLUTION MY PDA2k is dead :roll:
Thanks in advance.
Follow the wiki wm5 downgrade and use the doc tool to create a 16mb ext rom.
Deleteted your double post in hacking
MDAIIIUser said:
Follow the wiki wm5 downgrade and use the doc tool to create a 16mb ext rom.
Deleteted your double post in hacking
Click to expand...
Click to collapse
1st of all thanks for your reply.
I did follow the instruction but I got the error on the 1st post it seems that the Extended_Rom is deleted not resized to 128KB any tool to creat a permenent partition and name it Extended_Rom.
Thanks again.
Hi,
Try to install 2003 software, you can find it at Club Imate, as this will re-install the EXT-ROM then again Unlock it and Repartition it to 16MB. By this way you will get the original ROM Version 2003.
Hope this will help.
Daihi3003
daihi3003 said:
Hi,
Try to install 2003 software, you can find it at Club Imate, as this will re-install the EXT-ROM then again Unlock it and Repartition it to 16MB. By this way you will get the original ROM Version 2003.
Hope this will help.
Daihi3003
Click to expand...
Click to collapse
Thanks for your reply. But the problem is worse than that I tried this many times bt as the Extended_ROM (club i-mate) size 16 MB and the device Extended_ROM is reformated to 128 KB it cannot install it and when I tried to Format or Unlock it I got the errors as the 1st post and also I noticed that the bluetooth giving me license expired error and the device always freezes. If there is a program that Can Creat a temp disk like the one in WM5 or any method to Creat a drive like that (PERMENANT DRIVE) I'll be thankful
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Sam
Click to expand...
Click to collapse
after doing this you can flash any rom you want
Midget_1990 said:
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Sam
Click to expand...
Click to collapse
after doing this you can flash any rom you want
Click to expand...
Click to collapse
I dont know what to say to you except PERFECT.
Special thanks to you Midget_1990, imatrix and to all who tried to help.

USB/Serial v2.07 error hile upgrading ROM Sx 66 Blue Angel

Hi,
Can anybody please help me with this proble,
I am freaking.
I bought the phone SX 66 (Cingular) a week back and thought will download some cool things in the weekend.
I thought of upgrading the Rom.
The sequnce was confusing.
So I downloaded BAUpgradeUt file , EntelBL, GetDeviceDte, HTCRUU.DLLHTCRUU.cnf and xda3nbftool files on to a temp folder.
I guess I executed the BAUpgradeUt file (with Activesync on) and the phone was on the cradle connected to my laptop.
It restarted and went to a mode where the screen started showing USB v2.07
I removed the battery and tried restarting by pressing the power button, it showed serial V2.07 (as it was not connected to the cradle)
I waited for the battery to dry down but nothing is happening.
Now when i connect it back to cradle, it says USB V2.07
I am really worried.
Its a little difficult to understand fro the XDA forums, so can anyone help me step by step on how to fix this.
I mean which file do i need to execute.
Should i disconnect anything?
Pls explain in detail as i will miss out again and dont want to loose this.
I have unlocked this successfully erlier
Awaiting the earliest reverts
Thanks
Abhi
[email protected]
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Hi Midget, Thank you for the patience and being there.
I am sorry but I am still stuck with this.
Like mentioned by you,
1. downloaded mtty1.42.rar onto a temp fold on my laptop
2. Stopped wcescomm.exe from taskbar(the rapimgr was not running so dint get it)
3. Device was put into cradle (was saying USB v 2.07)
4. I executed the mtty1.42 extracted file(application)
("This is where I got stuck")
I got
open port setting popup
a. Asked me for Port (options were COM1,2,3 and USB)
I selected USB
b. Asked me for Baud:
I selected 115200
c. Databits = 8bits
d. Stopbits = 0bits
e. Localecho=No
f. Flow Control=None
e.Parity=None
When I say Ok, It opens me a window of Multi Port TTY Version 1.42 and within that there is another window that is opened that says
USB115200 N-8-1 and its a blank notepad kind of a file
(Do I need to type in anything into this and save and and download?)
5. U have instructed me to
a. Choose WCEUSBSH001 (where do i choose this from?)
b type "set 14 0" without the quotes to tell bootloader to boot the OS after reset. (where do I do this)
c. type "task 28" to get your device formatted (where)
d. type "task 0" to ask your device reboot (where)
6. take the device out of the cradle, and manually reset it if it does not do that already(I was not able to reach this stage).
Please take a little time in guiding me and sorry if I have been troubling you with basic questions and I m very worried and want to fix this sooner.
Also is it required for the phone to be charged suring this process and is it mandatory that I should ensure that it reads USB v2.07 while it is on the cradle?
Awaiting ur instructions and Thanks again s much
Abhi
Midget_1990 said:
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Click to expand...
Click to collapse
everything is fine, just type what i said into the 'notepad' window, pressing eneter after each line and removing the quotes, then remove from cradle and hard reset your phone
Hi,
I am very sorry, but I need help.
I am unable to fix this.
I am trying my best to follow the instructions and dont know where am i going wrong.
Like U said,
I went again with the Multi Port TTY utility and in the new USB text file window, ((stopped the wcescomm.exe application from taskbar)
I tried entering
set 14 0
USB>task 28
USB>task 0
USB>
Saved the file as USB
The phone in the cradle was still showing USB v2.07
I took the phone out of the cradle, removed the battery and inserted it back into the cradle
and i again starts showing USB v2.07
Where am i going wrong..
I also tried
USB>set 14 0
USB>task 28
USB>task 0
USB>
but in vain...
Please help in resolving this
Thanks
Abhi
Midget_1990 said:
everything is fine, just type what i said into the 'notepad' window, pressing eneter after each line and removing the quotes, then remove from cradle and hard reset your phone
Click to expand...
Click to collapse
I got same problem couple of days ago.
i tried this way, and it works for my PDA. but the only thing is my siemens sx66 bluetooth does not work any more, and tell me the license is expired. anyone knows the reason? i think the exrom wrong.
thanks.
andy xia
Midget_1990 said:
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Click to expand...
Click to collapse
I ****ed my BA like this guy and found this solution via google.
It worked perfectly. God bless you sir.
Stuck in Serial
The BA that I have killed is stuck in "Serial, v2.07". Placing it in a USB cradle does nothing. I have tried to connect using a cable I purchased, but I think I need a straight thru cable and I only have a null modem.
I want to verify that I should be able to connect via serial and do the same process?
Thanks.
padapa
i had ewhat a similar issue, my problem was caused by windows vista....not sure if thats what your issue is, but if you are running vista try this...
http://forum.xda-developers.com/showthread.php?t=291723
still in stuck serial
After a long break, I'm back to trying to recover this BA that is stuck in bootloader. I've read wiki's and forum posts till I'm blue in the face. I have two BAs, one with WM2003 and the "stuck one".
If I put the good BA into the cradle, it starts Activesync and the USB driver and I can connect via mtty and see the good BA, the "stuck one" does not start anything.
If I plug in my serial cable and put in the good BA, I see the "CLIENT" message. When I put in the "stuck one", I see nothing and typing the codes does nothting.
Any ideas would be greatfully appreciated.
Padapa
check the bottom PC IO/Connector of the BA physically for broken "pins"
Midget_1990 said:
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Click to expand...
Click to collapse
Not working bro :S
had the same prob here.
im back after a break. i gave up.
i think what i did wrong was using the usb hub. and since you had the issues w the cable... maybe....
im still looking for an answer.
lets see if we can make it.
follow the instructions as they may help.
these brains are good.
i posted this thread but im sure you already know.
http://forum.xda-developers.com/showthread.php?t=346510

EXTROM corrupted!! HELP ME!

Hi guys i just try to update from helmi 1.2 to 1.3. I did the steps as followed how i think i might has screw up some parts during the formating of the extrom....... Then how the device refuses to boot!!!! I have tried flash the extrom but i keep getting that extended rom error!! DAMN! Flashing of radio and CE rom is fine. only the extrom part!! Anyone can help me out please?!?!
Thanks a mil!
first u will need to put extend rom back to default value by following guide below and re-partition it again. finally, flash the new rom
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
imatrix
Hi imatrix!! thanks for your help!! really appreciate it. As expected it's the extrom that was giving the problem. I guess it got stuck at bootloader was because bootloader couldn't find any extrom files to load.
Thanks again
hi imatrix!
i've had the same problem, i thought i could never fix this error. Thank you very much imatrix for your expert help!!!
imatrix U R AN ANGEL!!!!!
From the deep south of Italy someone want offer u a great pizza!!!
TanksTanksTanksTanksTanksTanks

M2000 - my god what a job!

Well after many hours of trying I finally got a BA SPV M2000 unlocked!
Not your average unlock this...it was ex-BSKYB and had their software set to load and lock EVERYTHING out apart from their menu, so first job was to get rid of that - not easy as it was very locked down!
Many hard resets later and I managed to delete all the files it needed to run, but the browser(it was browser based and full screen - no exit option!) then still launched denying me access to the system.
Anyway in the end managed to get into it and then followed the instructions in the Wiki - now it's running WM6 and is fully unlocked!!!
Gawd what a mission! But just wanted to thank everyone who contributed to the Wiki and development of the unlock for making it as easy as it could be - after i blitzed the BSKYB software!!!
SU
Try This
I got this PDA Viet but it does work...
1. Download mtty v1.42
http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
Well i've done it now but for future reference would this have stopped the BSKYB software from taking over?
Cheers me dears
SU

Categories

Resources