Hi,
Ive upgraded my blue angel to WM5 (Patch 3) and installed all the other patches.
My bluetooth is version: 1.13 and i am getting weird problem.
When i use TomTom5 via my bluetooth gps everything is fine and no connection problems. As soon as i turn on my bluetooth headset tomtom loses connection to the gps unit. If i then switch off the headset - tomtom starts recieving gps data again.
Does ajnybody know how to get the bluetooth headset icon to display in the today screen as in WM3
Thank You
L 8)
i guess none of you guru's know the answer to this issues
Not a guru, but not experiencing the problem with my BT GPS and Headset running at the same time....
this seems like I/O problem to me. IT seems that your GPS receiver is listening on the same port as your BT headset in which case you need to check and change that. My GPS receiver has inbound port set to com 5 and outbound to com 6 (u can check this in BT settings).
K
For 2 weeks now I'm trying to get my Wizard working with this nokia GPS BT and Tomtom. I updated my rom to the 2.3 and still I'm having problems.
Sometimes it works for a week and then stops working.
Is there a way to test this BT GPS to see if it is working properly ?
I tried everthing possible, all suggestions in this post.
Hi there in the world of PPC's,
I have a problem with my QTEK 2020i and my new BT GPS unit.
I have running WM2003SE and BT broadcom 1.0.0 build 3900. Now is the problem that I can connect. Ok I hear you thinking what is than the problem, well the connection stays for a 5 minutes or so and than the connection is off. Reconnecting works and then again that round 5 min or so.
My BT GPS keeps working and it is not his problem as I tested that with my PC and a small program (written by my self) reading the GPS position and displaying the total of satalites.
Anyone knows a sollution? I think it is that BT driver in the QTEK
BR,
Martin
Hello,
Just upgraded to WM6 using the official Palm upgrade (TREO750-2.23-RWE).
The Treo is unbranded and came with WM5, also an RWE ROM.
The most important issue I currently have is terrible bluetooth interaction with my car-kit. Pairing is OK, I can start or receive a call, but there is no sound. Before, with WM5 I had no issues.
Setup:
- Treo 750
- WM6 (TREO750-2.23-RWE)
- Pegeuot RD4 radio with integrated bluetooth
Any solution? Or should I downgrade to WM5? If so, how should I downgrade?
Your help is most welcome!
David
Odd... With both the Treo 750 running WM5, I had the same problem. Basically, the first 30-60 seconds of a call wouldn't sound on either the handset, or the speakers over the bluetooth connection. This was always for the first call after getting in the car. To get around it, I would get in, start up the car, and call my voicemail. Once I could hear the call on the speakers, usually 30 seconds later, I would hang up. I could then make and receive calls normally.
After upgrading to WM6, incoming calls would occasionally be very low volume. I would have to hang up and call the person back. This also happens with WM6 on my AT&T Tilt.
No fix for that one....
daupers said:
Hello,
Just upgraded to WM6 using the official Palm upgrade (TREO750-2.23-RWE).
The Treo is unbranded and came with WM5, also an RWE ROM.
The most important issue I currently have is terrible bluetooth interaction with my car-kit. Pairing is OK, I can start or receive a call, but there is no sound. Before, with WM5 I had no issues.
Setup:
- Treo 750
- WM6 (TREO750-2.23-RWE)
- Pegeuot RD4 radio with integrated bluetooth
Any solution? Or should I downgrade to WM5? If so, how should I downgrade?
Your help is most welcome!
David
Click to expand...
Click to collapse
daupers,
Just curious that this might be related. Can you post what radio version you ended up with after the upgrade to WM6?
Dropped the issue at Palm
Yesterday I sent an email to drop the issue at Palm, since I used the official upgrade on an official pristine Treo. I still have to receive an answer.
I'm wondering if I ever will receive an answer that will resolve my issue.
Did anybody else on this forum ever get help from Palm?
David
Im heaving simmilar problems with Treo 750 WM5 and Toyota original BT-HF. Repatedly the connection is established, but then lost (without warning) - and then you get no sound (or an odd "interferrence " sound). I switch the BT off, then on, connect it again and it (usually) works fine. I assume it has smthng to do with the BT firmware. No other solution so far.
Where can I find a download for the original RWE WM5 ROM?
Can anybody provide me with a link to an WM5 RWE ROM for the Treo 750 (Cheetah)?
Thanks
I did some searching and so far I discovered the following.
WM 5 supports bluetooth 1.2.
WM 6 supports bluetooth 2.0, which should be backwards compatible with 1.2.
The carkit supports 1.2, but I'm not sure if it supports 2.0.
It looks like a compatibility issue, caused by the upgrade.
Could this be the source of the problem?
D
The hardware in the 750 supports 1.2 only, WM6 is backwards compatible with 1.2. Any device that supports 2.0 will be backwards compatible with 1.2. I just upgraded to the AT&T official WM6 build and am still having the same problems as always with my Moto HF850, no voice command, only get one working connection before the bond fails and I get no audio. *sigh*
I have the same problems Treo 750V 2.18-VFE with WM6.
Car: Citroen C4 with integrated bluetooth radio.
My car connects fine to the Treo, however when I make a call or answer a call 9 out of 10 times I have no sound. Currently I have to use the wired headset.... While I have no sound the connection is intact and I cannot use the Treo itself without cancel bluotooth from the menu.
I can read the indexes of the phone, make calls by using car functionality but no sound. Also when I have sound most of the time it's after ten seconds.
Since yesterday I also have no ringer sound anymore. Palm Support gave me an update but it's not for my ROM version.
I'm affraid I have to ask Palm to swap the phone again. Currently this is number 3:-( within a few months
BT working after WM6 upgrade
Hi everybody, surprisingly, after upgrade to WM6, my BT connection with toyota original handsfree started to work, I haven´t had a single "lost connection" since. Why is that I don´t know... Just to let U know - More lucky than the others...
I Received my fourth Treo last week. I now have ringer sound again (for now).
However I still have the sound problems with using my carkit.
My car connects fine to the Treo, however when I make a call or answer a call 9 out of 10 times I have no sound.
I get the same problem with an Orange SPV M3100 (HTC TYTN) and by factory fitted bluetooth kit in my Citroen C4... It's fine using the latest Orange WM5 ROM, but upgrading to WM6 stops the car kit from working, (connects, but no sound). I asked my Citroen dealer and they advised it was a known issue with 'high end phones like Nokia running Symbian, etc'. They had no idea about when a fix might be available.
Delayed or Missing Sound
Install the sound fix. That's what is there for.
What sound fix? Can you post a link, or let me know where it is?
Support also advised me to install the sound fix.
However it only work for lower rom versions.
When you install WM6 You will have a higher rom version.
The sound fix should allready be in WM6.
I think I'll try to contact Citroen about this...
Can not connect Bluetooth please help...
--------------------------------------------------------------------------------
I have tried to connect my qtek 2020i through bluetooth with my carradio. It is a blaupunkt casablanca MP57 with a bluetooth interface audio device.
When I search for device it finds the radio, next the security code is asked, I enter it, next it is paired. I have checked the "Hands free" option.
On the display of the audio device on the qtek, I can see the radio but I can not use it . When I try to make a call it says "Connection Failed".
When I use a a bluetooth headset it is working ok,
Is there a bluetooth update for an qtek 2020i?
Does somebody know the solution....
Many Many Thanx!!!
blaupunkt hamburg mp68 bluetooth problems with xda 2i
hi all,
a week ago i bought a new car radio, blaupunkt hamburg mp68. i have some difficulties, to connect it with a xda 2i. the xda can recognize the radio, but it's not connecting. does anyone have any ideas? blaupunkt bluetooth connection perfectly works with a nokia e50, and a nokia 6310i (that's a surprise!), so i don't understand the situation at all. previously my xda was connected with a bluetooth headset, a gps reciever, other phones, and my laptop, and it all worked fine (and still works fine). should i search for some kind of update for my xda? what are you recommend?
thanks for your help!
vic