Hi Helmi. I installed your ROM and I can say that it works fine.
Today I installed Tom Tom 5.21 and I see that TT does not recognize my Bluetooth GPS. I am able to see it as I installed the GPS bluetooth thourgh the BT menu, but in TT does not work.
What can i do for?. Thanks
You need to name your GPS device something like BT-GPS it must finish in GPS when you setup the device then you need to assign it a comport ie 6 and then pair it in tomtom to com 6
Hi. Thanks for your help. I tried to make the adjustment as you suggested, but it does not work.
I have paired the GPS bluetooth with BT software, but when I use Tom Tom with com 6 (port assigned to the GPS) i don't see any paring.
What i can do then?.
Thanks
Related
Hello all I have an xdaIIs and I can not get it to work with the tom tom navigator 3 I have tried all I can it will not pick up the gps at all is there a fix for this any where it is blue tooth
???????????? any help would be fantastic
J
I have an imate pda2k...but have you checked witch port the GPSis trying to open when connect?? If you try the BT gps will fail...need to be serial port on bt.(ysually 5 or 6).Another thing...have you paried the devices? Add a new device, click to discover services on it (GPS outpout in this case), type the key and connect from the shortcut yuo have created.Works for me, hope the same for you, byez!
The device is paired fine but I have not tried the ports so I will give that a go thanks
Also, uncheck 'Receive all incoming beams' in Start/settings/connection/beam.
Jason, when you bonded the gps it should have given a message regarding serial port profile, accept this then choose tomtom wireless gps in gps settings and in the bottom box choose bluetooth gps, failing that choose com 5.
Hi, i am having the same problems trying to get the two to work together, it used to work fine with my Xda2, but i cannot get it to work with the Xda2s.
the way you pair devices is different!!
On the TomTom GPS how do you get it to be ready to accept a connection for bonding?
Thanks in advance - very frustrating!! - O2 and TomTom just balme each other and dont help!!!
Try the following under the GPS section (2nd page where the world map is).
Top dropdown = NMEA 0183 v2 Bluetooth
Bottom dropdown = Blue tooth Serial Port COM6
Make sure the box is "ticked"
Also, switch on Bluetooth, go into bluetooth setting,select service, highlight serial port and make sure there is a tick in the Enable service box.
tomtom 3
when you use a bt reciever, just download de update 3.07 at www.tomtom.com
if you use wired , make sure you uncheck the infrared (beam)
this is also using your com1
good luck :lol:
right o im getting a new gps unit one off ebay I took the other one back as O2 have withdrawn tom tom 3 from being sold together they say its incompatible and wont work well I found all the kit at a fraction of the price of O2s so im going to try that if it does not work I will use my old xdaII.
also the guy at O2 stated we cant even open the kit to try and figure it out ourslelves
what are O2 thinking ????????????????
they just need to sort the rom out so it will can it be that hard
I thought I would add my tuppenyworth to the Tomtom problems with the XDA 2i. Bought a wired Tomtom "Official" GPS receiver for it and tried it with TT5 to no avail. It would not recognise the receiver at all no matter how I tried to specify it's com ports etc..
I eventually upgraded to TT5.1 and it worked immediately with no problems at all. Been working fine ever since.
if it matters
hi, i have a xda 2i and use tomtom 5.20, when i use my wired gps i was told to switch off the infra red beam, mine seams to work like that.
port problem?
could anybody help? my xda2i never works with tomtom5...
how to switch the beam off pls??
switch off receiving beam????
under setting > connections > beam
O2 XDAIIi with tomtom 5.21 and BT GPS receiver
but there is still problem with the signals, it can display the right UTC time, and numbers of satellites, such as 29 on the North, but there all gray and said no valid GPS signal!
the com ports couldn't be changed which are com5 inboard, com6 outboard.
does anyone know what the proble is pls??
ps: I installed the BTHTools1100, but no change
see the attachment pic
many thanks
Hi Piers,
i've got exactly the same problem :-(.
With a GlobalStar BT348, the GPS signals are plainly perfect. But when i connect the official Tomtom wired receiver, i only get the grey bars, although, like you, the UTC and spinning wheel are there, indicating the GPS is detected.
I looked at the compatibility list on the Tomtom site, and besides Dell and iPaqs, there seems to be nothing compatible with the wired receiver.
Anybody has other information?
Hi again,
I think I found the solution
1. of course, "receive all incoming beams" has to be off
2. apparently, you can not have a paired BT GPS receiver (even inactive) when you want to use the wired Tomtom receiver... :shock:
I guess it has to do with the way WM2005 deals with GPS... :?:
So, in BT devices, delete the partnership with the BT receiver and everything works fine with the wired one. In TT5, simply declare the receiver as a wired Tomtom
I used it this morning, driving 100km, 90minutes, without a crash or anything
I have a XDA 2s with Tomt Tom 5 on.
I have paired the Bluetooth gps receiver and although the GPS Viewer program picks up the gps signal on the pda via the Bluetooth receiver, for some reason Tom Tom doesn't connect to The Bluetooth Receiver.
It was working and it's suddenly just gone off.
I have tried uninstalling and re-installing Tom Tom but no luck.
Can someone help me please.
Daft question, but have you disabled InfraRed Beam in connections?
No i haven't but i can sure try
and i'll try anything at the moment.
I've disconnected all beams but no luck, i've even tried doing a hard reset but that didn't work either.
Hi there,
Has anyone made a TMC device working on the Athena?
I tried some version of the GNS FM9 adpaters but nothing worked.
Any ideas?
Thanks in advance for your help!
Have a good start into 2008.
greetz,
DAx
I agree - this would be very useful. I have iGo on my Ameo and it is brilliant (cant wait for iGo 8 or MioMap 2008 for the 3d visuals and road names) but it would be even better if I could get warned of upcoming hold ups on the major roads!
adamelphick said:
I agree - this would be very useful. I have iGo on my Ameo and it is brilliant (cant wait for iGo 8 or MioMap 2008 for the 3d visuals and road names) but it would be even better if I could get warned of upcoming hold ups on the major roads!
Click to expand...
Click to collapse
Hi,
just a question from my side:
I'm currently using igo with my Ameo and I have to wait and wait and wait and wait for the first GPS fix. It takes normaly between 5 and 15 Minutes until the first fix, even if I use the Quick-GPS Tool that comes with the Ameo. After that, everything works fine. How long does it take with your device and igo?
If I use my GNS GPS receiver (http://www.gns-gmbh.com/de/30_5843.php) I need only a few seconds until the first fix. And it supports TMC!!! I've searched a lot around to find another / cheaper solution to use TMC with the integrated GPS receiver, but I didn't find a working solution, so i decided to buy the GNS GPS receiver....
Regards
Andreas
AndreasF said:
Hi,
just a question from my side:
I'm currently using igo with my Ameo and I have to wait and wait and wait and wait for the first GPS fix. It takes normaly between 5 and 15 Minutes until the first fix, even if I use the Quick-GPS Tool that comes with the Ameo. After that, everything works fine. How long does it take with your device and igo?
If I use my GNS GPS receiver (http://www.gns-gmbh.com/de/30_5843.php) I need only a few seconds until the first fix. And it supports TMC!!! I've searched a lot around to find another / cheaper solution to use TMC with the integrated GPS receiver, but I didn't find a working solution, so i decided to buy the GNS GPS receiver....
Regards
Andreas
Click to expand...
Click to collapse
Hi Andreas,
hmm... thank for the link. That would be really the last chance to get TMC working for the ameo.
FYI, I use Mobile Navigator 6 and it fixes the gps signal really quick. I also use the Quick GPS and when I start MN6 the GPS signal fixes within 1 minute.
Greetz,
DAx
AndreasF said:
Hi,
just a question from my side:
I'm currently using igo with my Ameo and I have to wait and wait and wait and wait for the first GPS fix. It takes normaly between 5 and 15 Minutes until the first fix, even if I use the Quick-GPS Tool that comes with the Ameo. After that, everything works fine. How long does it take with your device and igo?
If I use my GNS GPS receiver (http://www.gns-gmbh.com/de/30_5843.php) I need only a few seconds until the first fix. And it supports TMC!!! I've searched a lot around to find another / cheaper solution to use TMC with the integrated GPS receiver, but I didn't find a working solution, so i decided to buy the GNS GPS receiver....
Regards
Andreas
Click to expand...
Click to collapse
Hi Andreas,
can you confirm that the GNS 5843 TMC work on the X7500 with Igo.
Thanks
Gigino
gigino said:
Hi Andreas,
can you confirm that the GNS 5843 TMC work on the X7500 with Igo.
Thanks
Gigino
Click to expand...
Click to collapse
Yes i.e. it works on my T-Mobile (Germany) Ameo with igo,
Cheers
Andreas
AndreasF said:
Yes i.e. it works on my T-Mobile (Germany) Ameo with igo,
Cheers
Andreas
Click to expand...
Click to collapse
Hey Andreas,
sorry to trouble you again but we are using the igo plus and the same gps as you the GNS 5843 but we can get the gps to work but not the TMC everytime we try to connect the TMC the pda just frezzes like the port has a conflict.
We have only been trying this in landscape mode can you tell me in which mode you are using the igo Portrait or Landscape.
Please can you help me in get this to work because I really like the Igo plus more the any anothe navigators.
Thanks
Gigino
Hi Gigino,
hmmmm, strange, for me it works. And yes, I'm using the landscape modus.
Sounds for me, that Igo uses the internal GPS receiver an tries to find a TMC connection on this internal GPS receiver.
Some Ideas from my side:
If you connect the GNS receiver via bluetooth, which serial port do you use? I've configured the bluetooth settings and then the COM-connections (I hope this are the right terms, I'm using a german ROM) with COM1 and secure connection. For instance Mobile Navigator 6 expects the TMC Signal only on COM1 and doesn't accept other ports.
The internal GPS Receiver is connected to Com4 on my system: GPS Settings -> Programms: Com4 and ->Hardware: None, 4800 Baud and -> Access: Automatic.
In a few words: internal GPS receiver on COM4, external GPS Receiver via bluetooth connected to COM1.
Do you have / use the test software from GNS to test, if youre GPS receiver is ok? You can download it on their page.
Last hint: Sometimes (Mobile Navigator6: every time!) you have to start the Navigator software twice to get a connection to the GNS 5843. It's a known bug for this receiver
Hope all this helps, otherwise contact me again
Regards Andreas
AndreasF said:
Hi Gigino,
hmmmm, strange, for me it works. And yes, I'm using the landscape modus.
Sounds for me, that Igo uses the internal GPS receiver an tries to find a TMC connection on this internal GPS receiver.
Some Ideas from my side:
If you connect the GNS receiver via bluetooth, which serial port do you use? I've configured the bluetooth settings and then the COM-connections (I hope this are the right terms, I'm using a german ROM) with COM1 and secure connection. For instance Mobile Navigator 6 expects the TMC Signal only on COM1 and doesn't accept other ports.
The internal GPS Receiver is connected to Com4 on my system: GPS Settings -> Programms: Com4 and ->Hardware: None, 4800 Baud and -> Access: Automatic.
In a few words: internal GPS receiver on COM4, external GPS Receiver via bluetooth connected to COM1.
Do you have / use the test software from GNS to test, if youre GPS receiver is ok? You can download it on their page.
Last hint: Sometimes (Mobile Navigator6: every time!) you have to start the Navigator software twice to get a connection to the GNS 5843. It's a known bug for this receiver
Hope all this helps, otherwise contact me again
Regards Andreas
Click to expand...
Click to collapse
Hey Andreas,
thanks for your help I well try again over this weekend.
They is another problem that I have and I've tryed everything but cannot resolve it.
I use the Igo Plus in landscape mode when I'm using the map and I get a reminder or a call the screen revertes to portrait mode and after accept the call or dismissing the reminder all the buttons in the Igo software goes all funny.
Do you have the same problem or have you find a way to correct this problem.
Thanks
Gigino
Ah I have this problem if the keyboard is attached but not if it isnt. What happens is that for some wierd reason the screen gets INVERTED! If you imagine where the button should be if it were upside down you can click it! Most odd!
adamelphick said:
Ah I have this problem if the keyboard is attached but not if it isnt. What happens is that for some wierd reason the screen gets INVERTED! If you imagine where the button should be if it were upside down you can click it! Most odd!
Click to expand...
Click to collapse
Hi,
I can confirm this also, the screen is inverted meens, that it looks ok, but you you have to touch it in an inverted way. I.e. the button is on the left upper corner of the screen, but you to click in the right lower area. Thats really strange. I've have the feeling, that this happens very often, if you use the Map view instead of the cockpit view.
@ gigino: I use the ameo with a brodit mount without the keyboard, so I don't have this problem.
In my last message is a little mistake, you have to switch OFF (and not ON) the automatic access in the GPS settings.
Regards
Andreas
I've brought this GPS: http://www.techfocus.co.uk/GPS-Rece...TFSN20&tduid=9c2b6aadcc4ca8e0d3f6a72baf759c60
but can't get it to find any satellites on S730 trough Google maps or Route66 (Route66 says no GPS). If anyone has the tool or any tips, please let me know
Edit: Found the GPStool and it finds three satellites and has fairly good reception, but Route66 doesn't find it.. says there is no GPS...
try to move around
hi
set in bluetooth settings for gps receiver com# port and in the route66 (gpstool) set bluetooth GPS receiver on com#.
Drobcek28 said:
hi
set in bluetooth settings for gps receiver com# port and in the route66 set bluetooth GPS receiver on com#.
Click to expand...
Click to collapse
Thanks I had done that, but I found my mistake... I don't get to connect to any satellites where I live, so I have to drive some meters before I get any signal...
Thanks everyone
Or try this app