I have the T mobile Vario. Tried to change language from French to English. I upgraded the ROM but now activesync is not being detected, battery showns no info and phone is very slow. I have read many threads and tried countless of suggested course of actions any suggestions?????
This happened to me on my Qtek 9100.
You did not flash your ROM properly, you need to flash it with a clean ROM.
DId you CID unlock your phone before flashing? I did this to my Qtek 9100, and it screwed it all up.
You need to get back into the boot loader mode (rainbow screen) to be able to reflash.
No worries you didnt brick your phone.
i got to the bootloader mode and trying to reflash. still getting invalid vender ID. can u give steps and software you used?
Hmmm..
You have a Tmobile so you should use a Tmobile ROM for your Vario.
Restore it back to factory. You are getting an INVALID ID code because yoru device is CID locked and because you porbably installed partial ROM which is why your Phone mode and pda is all operating slow and non-functional.
Thats all I did. I used a Qtek ROM to reinstall, then did a CID unlock and then installed Mr. Clean. Then dropped it into a cup of coffeee and bought a Q2 mini S
minirx7 said:
You need to get back into the boot loader mode (rainbow screen) to be able to reflash.
Click to expand...
Click to collapse
Same problem here ... how do I get there?
Einstein said:
minirx7 said:
You need to get back into the boot loader mode (rainbow screen) to be able to reflash.
Click to expand...
Click to collapse
Same problem here ... how do I get there?
Click to expand...
Click to collapse
Giving an anser to myself:
holding the camera button down and doing a soft reset with the stylus
Click to expand...
Click to collapse
Related
I was running xelencin's latest custom rom. I have used his previous versions and all was good.
This one hung at 98%. I was just letting it do its thing when out of nowhere, BSOD. So now my phone is just sitting at 98%. I thought there was a forum post here about recovering but I'm not able to find it.
Thanks.
Update: After a soft reset, I am back to the multicolor screen. When I plug it in, it says USB in the bottom left hand corner. Device manager shows a PocketPC USB Sync device as well.
When I perform a hard reset (Comm Button + Voice Dial held, then press soft reset with stylus), I am taken right back to the same multicolor screen.
You're at the bootloader.
This is a Good Thing(tm).
At this point, you should be able to rerun any (assuming you are CID unlocked) any RUU ROM upgrade. Let it do its thing and you'll be good to go.
gamescan said:
You're at the bootloader.
This is a Good Thing(tm).
At this point, you should be able to rerun any (assuming you are CID unlocked) any RUU ROM upgrade. Let it do its thing and you'll be good to go.
Click to expand...
Click to collapse
For those that get stuck here in the future:
I had to extract the installer so as I could get past the CID unlock. I then ran "ROMUpdateUtility_Wizard_NoID.exe" and all went well!
rosewood said:
For those that get stuck here in the future:
I had to extract the installer so as I could get past the CID unlock. I then ran "ROMUpdateUtility_Wizard_NoID.exe" and all went well!
Click to expand...
Click to collapse
Yep, I went thru the exact same thing yesterday when trying to upgrade to 2.24. My PC decided to shutdown (not restart, a complete instant shutdown!) at 8% flashing. I decided to grab the "Mr Clean AKU2.3 ROM" which already had the ROM flash program available separately and then just put in the .nbf file I wanted and it was good to go
if your not cid unlocked, then what? xtract what? to wherehow can i transfer any thing, it seems though the device screen says usb, the avtivesync doesnt detects my phone. n?m, ive got it
What happen when your not CID unlocked? I had removed my hardspl before I tried to again flash a rom. I am stucked with the bootloader now...
Pls help
xpxj said:
What happen when your not CID unlocked? I had removed my hardspl before I tried to again flash a rom. I am stucked with the bootloader now...
Pls help
Click to expand...
Click to collapse
Only Official stock rom or the wizard_love rom will get flashed,no other wm6 rom is possible.
Hi everyone! I am badly need help to fix my MDA. My MDA stuck when it boot up to T-mobile white screen. I tried to do hard reset by pressing and holding Conn Manager and Voiddial buttons while pressing reset then press Send. I got and message
Format FAT Partition
Format is Failed
Now I am still able to flsh with any ROM but I just doing the same thing, stuck on boot screen. Is it the end of my MDA? Please hel
Is it realy no one can help?
I don't believe that no one can help me even a command.
If I have the whole white screen, the device was like in bootloader. Flash can start and than wil all OK..
I think You wrote wrong Start Adress in Your own ROM
If I have the whole white screen, the device was like in bootloader. Flash can start and than wil all OK..
I think You wrote wrong Start Adress in Your own ROM
I don't get it
Johnnnnnnnnnny said:
If I have the whole white screen, the device was like in bootloader. Flash can start and than wil all OK..
I think You wrote wrong Start Adress in Your own ROM
Click to expand...
Click to collapse
What should I do? any rom for me to flash to solve this problem?
You could flash any originaly ROM with write IPL/SPL
and quicky. If the battery will turn off. the Wizard will bricked
I flash with right rom
Johnnnnnnnnnny said:
You could flash any originaly ROM with write IPL/SPL
and quicky. If the battery will turn off. the Wizard will bricked
Click to expand...
Click to collapse
I flashed with T-mobile ROM 2.26. It went thru 100% but when the device reboot, It just stuck on the T-mobile boot screen wich saying
IPL: 2.26
SPL: 2.26
GSM: 02.25.11
OS: 2.26.10.2
Finally
Finally I got my MDA fix.
Re: Finally
KhMeRA said:
Finally I got my MDA fix.
Click to expand...
Click to collapse
Please tell everyone what you did to fix your problem.
Molski
he was in bootloader.. He hasn´t brick her phone by wrong xG IPL/SPL
Re: Finally
molski said:
KhMeRA said:
Finally I got my MDA fix.
Click to expand...
Click to collapse
Please tell everyone what you did to fix your problem.
Molski
Click to expand...
Click to collapse
Just follow this link http://forum.xda-developers.com/viewtopic.php?t=62268&start=0&postdays=0&postorder=asc&highlight
please tell us whate happend (fixed or no )
sifreen said:
please tell us whate happend (fixed or no )
Click to expand...
Click to collapse
Read post #8 on the 1st page.
Hi,
I wanted to update my trinity in the version of S300+ (French) with the original HTC ROM.
Not only it didn't work, but I lost my phone, I cannot access anything even with Hard Reset and battery removal...
When I want to upgrade, it's going till 1% and then it stops and I'm getting a message "Error 286" Cannot connect with phone.
I cannot hard reset, I cannot do anything! When I hard reset, I'm always coming back to the bootloader (I think it's the bootloader, the screen with colors, where it says numbers and it's says USB).
Any idea? A upgrade with miniSD will help?
Thanks!
Start flash utility again and wait untill it starts again (can take sometime).
I had it to when I first flashed a rom.
Hi,
I tried it already, but it's always blocking at 1% of progress and it's telling me in the computer Error 286, and the phone resets and comes back to the bootloader...
Any idea?
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
This will solve all your problems:
http://forum.xda-developers.com/showthread.php?t=308691
sharedworld said:
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
Click to expand...
Click to collapse
Put the phone in BOOTLOADER, then disactive ACTIVESYNC (form menu). After then start MTTY (you found it in the forum) set it on USB and then give the command:
task 32 Enter
task 28 Enter
task 2A Enter
info 8 Enter
task 8 Enter
After the last command the PDA restart and then you make a normal flash.
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
qubit76 said:
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
Click to expand...
Click to collapse
Please give more instruction howto
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
biohazard said:
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
Click to expand...
Click to collapse
SFR dosen't give any ROM... But the problem is that I cannot get out the bootloader, but I'll use the solution given here.
Thanks!
sharedworld said:
SFR dosen't give any ROM... !
Click to expand...
Click to collapse
Looks there]...and flash again
shym said:
Looks there]...and flash again
Click to expand...
Click to collapse
It's a DUMP... And not a full one... For ex. you do not get the splash screens...
I was upgrading my MDA using the official mda update 2.26 and then the phone completely froze. When I soft-resetted the phone, it wont get off the T-Mobile load screen. I tried to hard-reset it using the voice+commanager to reset, but then it just goes back to the T-Mobile load screen. Can anyone help me? I also tried to flash the Wizard_Love on the 3 color screen but it keeps giving me error 200. Please I need your help.
wow no response to such a serous problem. I'm having the same issue I down loading and install to my storage card some files gps navi apps from the ppc freeware site. while trying the apps my device froze. I held down the power button and it didn't respond so I removed battery.but device won't lad pass the second start up screen. what do I do
collwatt said:
wow no response to such a serous problem. I'm having the same issue I down loading and install to my storage card some files gps navi apps from the ppc freeware site. while trying the apps my device froze. I held down the power button and it didn't respond so I removed battery.but device won't lad pass the second start up screen. what do I do
Click to expand...
Click to collapse
Remove the sdcard/minisd and do a hard reset.
Bricked?
Hi all,
i have similar problem like Lo0o0nG.
Tried to flash wm6 on my g3 wizard following the wiki:
Flashed the Button ROM "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM" but after rebooting the wizard stucks in the first screen with the beer glass on it - showing IPL 1.01, SPL 2.21, GSM 01.12.10 and OS 1.5.4.2.
Then nothing else happens...
Did this 6 or 7 times before with g3 and g4 phones - worked perfectly till now..
Are there any suggestions / any possibility to get my phone working again?
thx,
derHarry
If the phone is CID unlocked use the SD/mtty method to restore the full ROM image.
If it's not CID unlocked then try to unlock it with WST and reflash the ROM(s)
Thank you for your fast reply!
It's not CID unlocked, but WST can't connect to the device...
any other suggestions?
I'm sorry but WST can't connect unless the OS has booted already. I didn't realize it when answering.
I guess the only solution now is to use the commercial unlocking solution by IMEIcheck.co.uk
Thank you for your suggestions,
i think i'll replace the touchscreen from this bricked device with the broken one from my other device... so it's not that tragical
btw: how could this happen? did i something wrong while flashing?
derHarry said:
Thank you for your suggestions,
i think i'll replace the touchscreen from this bricked device with the broken one from my other device... so it's not that tragical
btw: how could this happen? did i something wrong while flashing?
Click to expand...
Click to collapse
Yes. I believe you flashed a ROM without permission (CID unlocking) or an upgrade went wrong (stopped before finishinfg) and now the bootloader 1.xx can't load the OS because the 2.xx address is different and can't be found.
cheers
Hello.Sorry for wrong english.
my problem is on cingular 8125
I bought it with problem.
On splash screen it freeze, i flash RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1,because it firmware for cingular 8125. and it freeze too.
Can you help me?
my ipl 2.25
spl 2.25
gsm 02.25.11
os 2.25.11.1
Thank you. and again sorry for wrong english.
Ok Dude here is your solution ive found it myself after Searching
I will not be liable for Bricking your Device you do this at your own Risk*
First of All Is your Phone CID unlocked?
if it is check to see if you can hard reset if your phone says Format is Failed then here is your fix
First flash factory rom
grab a minisd that is blank *Warning it will Overwrite any card you put in*
enter into bootloader
reset+ camera button
in windows xp
Download mtty
http://forum.xda-developers.com/attachment.php?attachmentid=71806&d=1203597568
Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
run program
set port to
\\.\WCEUSBH001
click OK
*Warning it will Overwrite any card you put in*
type in at CMD>
r2sd all
then press enter
after it finishes reset pda and return back into bootloader mode
reset+ camera button
it will ask if you wish to flash from sd press Voice Command button to accept
after 100% complete reset phone you should be able to get back
hello. thank you for a help. mtty says me You didn't get the proper security level to download a specific image. why i do wrong?
cg_ar said:
hello. thank you for a help. mtty says me You didn't get the proper security level to download a specific image. why i do wrong?
Click to expand...
Click to collapse
Your phone is CID locked,Mtty will not work in this situation. Have you tried a Hard Reset.
Does it display any error message while flashing the official Rom,does it complete flashing or stops with a error message ?
Which windows you are flashing with,WinXP or Vista ?
when hard reser it says me a fat format failed. all sw flash without problem.
Anybody know how this is repair? (sorry for wrong english)
cg_ar said:
when hard reser it says me a fat format failed. all sw flash without problem.
Anybody know how this is repair? (sorry for wrong english)
Click to expand...
Click to collapse
how it cid unlock in bootloader mode?
cg_ar said:
how it cid unlock in bootloader mode?
Click to expand...
Click to collapse
You cannot CID unlock in the Bootloaders,it has to have a working OS (Rom),try to flash a rom,try these roms,lets hope one of them might work, Button's Rom 1.05 or xda_minis_launch or wizard_love_rom and official rom of your carrier and if there's any sdcard/mini_sdcard inserted in the phone,take it out before flashing,just keep on trying the different roms,its a catch 22 situation,it won't let the rom flash,stuck at splash screen and still it won't get CID unlocked in Bootloaders or use the Mtty method.I can imagine your frustration,but you gotta keep on trying.
i tried Xda_MiniS_LaunchROM_v154102,wizard love,button and original rom from cingular. and it freez on boot at all roms,and cannot make a hard reset. what i will doing next?
in this condition phone is not repairable?
cg_ar said:
in this condition phone is not repairable?
Click to expand...
Click to collapse
YES ! it is repairable,but not free,you'll have to pay for getting the CID unlock code from 'imei-check' uk.They might charge you around 20 or 30 dollars and provide you with a unlocking code,after that you'll be able to flash any Rom,but,here we were trying to get it working free somehow! Anyway, the choice is yours now,but certainly it is repairable,don't loose hope !
zabardast_1 said:
YES ! it is repairable,but not free,you'll have to pay for getting the CID unlock code from 'imei-check' uk.They might charge you around 20 or 30 dollars and provide you with a unlocking code,after that you'll be able to flash any Rom,but,here we were trying to get it working free somehow! Anyway, the choice is yours now,but certainly it is repairable,don't loose hope !
Click to expand...
Click to collapse
I know a way to avoid paying and manage a security_level=0 to allow "r2sd all"
It's just a matter of flashing a SoftSPL for G3 and use mtty
"Hello,
if the device doesn't boot up in windows then unlocker it will not work!
Regards,
IMEI-CHECK Team"
it says on imei-check.
how i will did?
what is softSpl for g3? please give url. thank you
mestrini said:
I know a way to avoid paying and manage a security_level=0 to allow "r2sd all"
It's just a matter of flashing a SoftSPL for G3 and use mtty
Click to expand...
Click to collapse
hey m8
You referring to 'JumpSPL' or something ? thats interesting
cg_ar said:
"Hello,
if the device doesn't boot up in windows then unlocker it will not work!
Regards,
IMEI-CHECK Team"
it says on imei-check.
how i will did?
what is softSpl for g3? please give url. thank you
Click to expand...
Click to collapse
hmmm, so imei-check' said that,yeah ! I presume,you got to have a working OS (Rom)
Well, softSpl for G3, I'm not sure myself,let mestrini handle this.
zabardast_1 said:
hey m8
You referring to 'JumpSPL' or something ? thats interesting
Click to expand...
Click to collapse
Something like that
If i recall correctly while developing SoftSPL for G4, The Equinox also made a G3. Problem is no one ever thought of a use to it (until now, and i have others hehe )
mestrini said:
Something like that
If i recall correctly while developing SoftSPL for G4, The Equinox also made a G3. Problem is no one ever thought of a use to it (until now, and i have others hehe )
Click to expand...
Click to collapse
WOW !
I'm all anxious here...... eyes n ears !!!
i download a wzg3.7z. unpack and have
Hard-SPL.nb
JumpSPL.exe
SPL.lnk
spl.nb.
it has in pack 145kb is it alright?
and jumpspl cannot execute and spl.ink too. How this flash?
cg_ar said:
please mail me softspl for wizard g3. because from my ip on rapidshare already downloading. please mail on cg_ar(a)mail.ru
Click to expand...
Click to collapse
Well, I do realize your frustration,but this application still needs to be tested and tried first,as far as I know,it has not been applied and tried yet.
But keep your fingers crossed as I'm,hope it comes out successful,it wud solve this problem of not allowing to "r2sd all" using mtty in CID locked device.
hmm, there's a flaw in my theory: It's necessary to access WinCE (WM) to allow Haret to do it's job
Maybe there's a work around i can think of...
sorry
cg_ar said:
i download a wzg3.7z. unpack and have
Hard-SPL.nb
JumpSPL.exe
SPL.lnk
spl.nb.
it has in pack 145kb is it alright?
and jumpspl cannot execute and spl.ink too. How this flash?
Click to expand...
Click to collapse
What to do?