Hey Guys,
I was following the Helmi guide to install WM5 at the point where the guide states that you should put the device into bootloader mode (#4) I accidently did a hard reset.
Eversince I haven't been able to turn the BA on, there is nothing on the screen. Tried all manner of soft reset, hard-reset and bootloader sequences just to try and get a reaction out of the machine but, nothing. It doesn't light up whether its in the cradle or not. Windows doesn't pick it up at all. Have tried the mtty 1.42 utility as suggested, windows doesn't pick it up.
Have you guys got any ideas how to get it to reset or go into bootloader mode or maybe just switch on that would be a start I guess
Any help would be greatly appreciated!!
Cheers
Related
omg wtf do i do now?! my pc rebooted 31% into the flash.. it blue screened out of no where!
now its stuck on a IPL 2.21 screen!
this happened to me a few times as well. I just re-tried the flash from another machine and it worked fine.
but i cant establish a active-sync connection because the phone wont start it just stays at the 2.21 screen thats red/green/blue/white! omg im about to cry what do i do lol
I have seen the same screen, and have also had the computer blue screen on me probably 3 or 4 times now. When i plugged it into another machine with activesync, i ran the updater and it worked fine.
im trying it right now on 2nd pc still downloading the rom file tho
ok i was able to flash using another computer thank god!
:lol:
Can you post the steps of reflashing the wizard? I've tried a flash on another system, but it still doesn't work...
My steps:
1. Install Active Sync 4.1
2. Connect the wizard on usb
I've tried to downgrade the wizard with wizbackup. wizbackup need to flash IPL/SPL 1.01. The flash was ended without errors. But now the wizard starts and I only see the three colors and the version of IPL/SPL. Then I connect the wizard, Active Sync doesn't get a connection to the phone.
UPDATE:
In another thread I read that the wizard can't be flashed in IPL/SPL 1.01 without an OS. Can anyone verify this information or help me?
UPDATE II:
I finaly found out, that the phone can be restored with an image from the sd-card.
1. Put an image from the system to sd-card with psdwrite.exe
2. Power Off the phone and put in the sd-card
3. Power on the phone holding the camera key
4. Then the bootloader is coming up, press the voice key during 3s
5. The bootloader upgrades your phone from sd-card
Good luck!
that **** happens to me all the time, it always crashes to the boot loader and once its there you can just restart the upgrade no problem. if you need to boot into the boot loader then simply, from a turned off state, hit the wifi button, voice command button and power button, then release the power only and it will boot into the tri colored boot loader. then reinstall your image and soon you will be kickin it with your **** in it once again! booyakasha!
actually now that i think about it that will just go to the hard reset screen. you really just want to stick the stylus in the reset hole if you need to get to boot loader i think. i dont remember off hand.. just mess with it. if you break it just say you got it that way and exchange that ****
I have a problem and I've search the forums and search google and I find people with somewhat of the same situation im in... but the methods to fix them don't work.
My problem is,
I have a T-Mobile WING (Herald)
I am flashed on soft SPL with SPL 4.70.Yang
I am ROM flashed to Touch-It WM6.1
I want to flash back to the stock T-Mobile Rom
I run the Stock RUU and it enters the bootloader and at 1% the wing resets
I then get a connection error 260 and the flash will not proceed.
I have tryed restarting my device/computer. unplugging my usb putting in another slot... and still nothing. Any help would be appreciated I'm really unhappy with Touch-It and want to go back to stock and do some customization that way.
you need to extract the .nbh file from the stock rom using 7-zip or winrar on the ruu executable. Make sure you don't extract the spl.nbh file. I think the file you want is something like RUU_signed.nbh
then put it into your HardSPL folder and flash away
Yep. Besides, 4.70.Yang is a HardSPL, not a softspl. If you want the SPL to also return back to stock for warranty issues, then just use USPL along with the tmobile NBH. If not, do what fzzyrn said for the best results.
Got to this thread:http://forum.xda-developers.com/showthread.php?t=421304
Go to post #2 and download the Herald-USPL-beta3
extract the nbh file from your rom and place it in the ruu folder that is located in the flash center folder.
run the utility.
spacemonkey333 said:
Got to this thread:http://forum.xda-developers.com/showthread.php?t=421304
Go to post #2 and download the Herald-USPL-beta3
extract the nbh file from your rom and place it in the ruu folder that is located in the flash center folder.
run the utility.
Click to expand...
Click to collapse
And that links to this.
My T-mobile Dash 620
I HAVE THE SAME PROBLEM . I WAS UPDATIND THE ROM OF MY 620 WITH HTC_S620_WWE_BT_3.66.424.1_4.1.13.44_02.94.90_Ship AND THE PHONE RESTART ADN WHEN THE PROCCESS GOT 25% POP UP A MESSAGE ERROR 260 AND IT WAS RECOMMENDING ME UNPLUG THE USB CABLE AND REMOVE THE BATTERY AND CONNECT IT AGAING SO. I TRIED HARD RESET AND IT DOESNT CONNECT THRU ACTIVESYNC AND ITS STUCK AT THE BOOTLOADER SCREEN (HTC). I TRIED REFLASHING RADIO AND NOTHING WORKS. PLEASE HELP ME. I BROKE MY PHONE.
ROMEROPOLACO said:
I HAVE THE SAME PROBLEM . I WAS UPDATIND THE ROM OF MY 620 WITH HTC_S620_WWE_BT_3.66.424.1_4.1.13.44_02.94.90_Ship AND THE PHONE RESTART ADN WHEN THE PROCCESS GOT 25% POP UP A MESSAGE ERROR 260 AND IT WAS RECOMMENDING ME UNPLUG THE USB CABLE AND REMOVE THE BATTERY AND CONNECT IT AGAING SO. I TRIED HARD RESET AND IT DOESNT CONNECT THRU ACTIVESYNC AND ITS STUCK AT THE BOOTLOADER SCREEN (HTC). I TRIED REFLASHING RADIO AND NOTHING WORKS. PLEASE HELP ME. I BROKE MY PHONE.
Click to expand...
Click to collapse
The S620 is not a herald and every phone is different, so I'm not sure if we could help you out. Does your phone have a HardSPL? Have you used HardSPL before? Even if the activesync icon doesn't start trying to sync it doesn't mean that it's not connected, it just means that it has nothing to sync (since it's in bootloader mode.)
I FIXED
I Did These Steps:
I Turned My Phone Off
I Pressed The Camera Icon Button
I Turned The Phone On (no Loose The Camera Button)
It Got Into Boot Mode
I Plugged To The Usb Cable
I Oppenned The Ruu For My Phone Version
And Wowla Fixed
Thank You Guys For Your Help
The Answer is in a Careful Search
This post is being made to you about... a month too late. But that's because I just got the Wing yesterday and started trying out roms today. Anyway, ran into the same problem earlier today and found the answer in the forums. I've written the following for those who might need all the steps. In your case, read from step 3. Anyway, in case you still have this problem, here's what you do:
1. Hold camera button when pressing the soft reset to get into the bootloader; it should be in red blue green and white. something like that.
2. Connect the usb to the computer and run the stock RUU Utility (this can be found on the official t-mobile website. look under something like support/downloads for the Tmobile Wing)
3. When it hits the 1%, the phone will automatically restart. When it does this, it breaks the connection between the computer and the phone. At that instant, hold the camera button and the soft reset button. Then, when you let go of the reset button, it should go back to boot loader.
4. At this point, the Rom Utility should give you the error. Do not take out the battery as instructed. Just disconnect the usb, reconnect the usb, wait for the computer to recognize it (it should appear in my computer) and then just continue the utility.
Good luck. =)
i had the same problem flashing my P4350 yesterday. tried a lot of different things, the solution for me was:
1. start flashing from the bootloader
2. just to hold the camera button when the phone restarted after 1% (nothing else, no soft reset or anything).
this resulted in the phone restarting in bootloader again, and after that it just resumed upgrading the rom.
koekiemonster said:
i had the same problem flashing my P4350 yesterday. tried a lot of different things, the solution for me was:
1. start flashing from the bootloader
2. just to hold the camera button when the phone restarted after 1% (nothing else, no soft reset or anything).
this resulted in the phone restarting in bootloader again, and after that it just resumed upgrading the rom.
Click to expand...
Click to collapse
This one works for me. Thx!
hey guys,
need some help from the xpert here, my tilt cannot boot up its stuck on the AT&T screen, i have tried soft reset, hard reset and still cannot fix the problem. the worst problem is cannot sync into my pc...
thx
you sure you attempted to hard reset and still nothing?
take out your memory card and see if that does anything.
If it still won't boot up, then get into bootloader mode and re-flash your rom.
We need a bit more info to help:
1. Did you have HardSPL installed? Check by looking at the tri-colour bootloader screen (press and hold power/camera buttons and reset with stylus at the same time).
2. What ROM/radio do you have?
3. Did you try to flash another rom or radio before this problem hapenned?
4. When you hard reset, did you get the grey screen with instructions telling you to send to continue? Sometimes the hard reset routine doesn't always work properly.
5. Are you running XP or Vista on your PC?
Try going into the bootloader and connecting the USB cable. The screen text at the bottom should change from 'Serial' to 'USB'. If you have Hard-SPL you should be able to re-flash any rom (some here) - but check for compatible radios. If you don't have hard-spl try flashing the manufacturers original rom.
I flashed my att tilt with hard spl 3.29.
it worked good after that.
i did not hard reset afterwords though and tried to use the unlocker:
Kaiser Sim Unlocker v0.1
========================
Brought to you by jockyw2001
(c)2008 jockyw2001
after step one flash it wouldn't reconnect.
i did hard reset and it boots with att logo, then flying 3g logo, then goes blank. Sometimes it does a garbled color screen.
I can't reconnect with active sync anymore.
I can't boot into bootloader. (hold camera and power button, then hold stlus reset.
It just boots the att and 3g then nothing.
anyone?
googling gets me no answers.
thanks in advance.
I have tried to use mtty, but cannot get access to usb ports
solution: reinstall activesync
So I reinstalled activesync and it opened a connection with the scrambled tilt just fine. I flashed hardspl 3.xx just to be sure, and then flashed with 1.65.21.18 from htc to get windows 6.1. forgot the hard reset between the two steps, but things look much better this time regardless.
Hello everyone,
I am having problems to connect my Tilt to my pc.
First of all, when I power it on, the screen goes black and says "smart mobility" .. so far so good; but after a few seconds it starts again and loops endlessly. At that point the only way to power it down it to take the battery off.
I installed the drivers manually (Vista) and hoped to be able to use mmty (after pressing "camera button" and " power button") but I never managed to get a connection.
Does anyone have any ideas on how to get my HTC tilt back to a running state?
Sooo, this only happens when connected to the PC or all the time?
It happens all the time even when not connected to PC
I forgot the most important part ... this happend since I tried to update windows mobile (source downloaded from HTC official site).
Hard reset?
if you mean holding down both green and red headset button+pressing the reset button, yes I've tried that but didn't change anything.
It went through a whole process and nothing changed? Try to flash back to an oem rom. (seems to be the new popular suggestion).
ok but how can you do that if you can't get to connect it to a PC via usb?
By following the proper steps to flash a phone either by usb or SD card.
The phone doesn't need to be fully booted to flash.
Ok, that's good news for thanks.
If by any chance you have a link to a tuto in order to do that you're welcome. Otherwise I'll google it and get back to you to keep you posted.
It's all in the sticky
http://forum.xda-developers.com/showthread.php?t=397434
Thanks I shall try to night
Thank you for your time. I finally managed to do it and my HTC is back to running.
The only problem I had trouble to solve (if it can be of any help to anyone) is that I had to unrar the *.exe which I didn't could be done.
Thanks again