My MDA is runing with Motorola H700 Bluetooth. Everytime when I turn off my blutooth before ending the call I will lose the connection until I restart the device. Any one has this problem?
Related
Since I upgraded to Summiter's Test2 and now the multi-installer, I can not switch to phone handsfree. There is a button on the call status page that says "speaker on". It used to be I could press that and it would switch to speaker phone (away from BT). Now pressing that button does nothing.
The reason this is a problem is that it's easy to leave the BT headset in a different location than the phone. If I initiate a call from the phone, it automatically connects to the BT headset.
On recieving calls, I know to press the hard button for "talk" and it will let me use the phone in the traditional mode (even if the BT is connected). BUt when I initiate a call, I don't have any choice like that.
Thoughts? Am I the only one with this problem?
RayB
I've been experiencing this problem on my TyTN II with the original ROM. The programs I have installed which may be affecting the problem are:
-CooTek TouchPal 2
-TIInit_4_2_38 Kaiser (Official HTC Bluetooth Fix)
- duttythroy v3 Voip Setup
- Microsoft Voice Command v1.6.17913
Here's the problem:
- boot up the TyTN II (after being completely powered off) or toggle Bluetooth power off & on, with paired bluetooth headset within range and on
- Go to Phone screen. Headset icon is there indicating that the Bluetooth headset is connected.
- Press talk/send button on Bluetooth headset to start Microsoft Voice Command or answer an incoming call.
Result: Headset beeps as expected, but nothing happens on the TyTN II. Voice Command is not initiated. Incoming calls are not answered.
Workaround: If I go to Start>Settings>Connections>Bluetooth... Tap & Hold on my Bluetooth Headset, then choose "Set as Hands Free" the headset beeps again indicated that it made a connection. After I do that, all is as it should be! I can activate Voice Command, and answer/end calls with the Bluetooth Headset. I should not have to set my Bluetooth Headset as the Handsfree device everytime a reboot or toggle the Bluetooth power status.
I suspect it might be the Voip implementation, or the HTC Bluetooth "fix" but haven't done a hard reset yet to test.
Has anyone else had this problem? Does anyone know of a solution??
What headset are you using? I have the same software (except ROM) as you and haven't experienced this problem. I can SR with headset on and it will reconnect once the device reboots.
I tried it with the Nextlink Invisio G5, and Bluespoon AX2, both of which worked properly with other phones (HTC P3300, Nokia N95, etc., etc.,). I can try other headsets, but I'm pretty sure it's the phone software.
If your Voip and MS Voice Command are the same as mine and everything is working properly, maybe it's the HTC Bluetooth "fix". I guess another hard reset is in order soon.
I am having a huge problem with my carkit (JVC AVX33) Sometimes it works, and other times it just boots the BT on my diamond every 30 seconds.
I have figured out what is wrong, i think....
When the phone tries to push connection to the JVC and transfer all the contacts, it starts "rebooting BT" However when the JVC initiates the transfer it usually works.
Is There a way to disable the phone from polling BT units? a way to stop it from trying to initiate bluetooth contact, and just "listen" for incomming connections instead of trying to be the "Master"?
Kind Regards
Cosmodk
Hi,
I'm using my X1 with my car as a handsfree. Never had any problems with the car built-in handsfree so far. A couple weeks ago, the X1 started to show an odd behavior: After receiving or making a call, as soon as the call finishes, the X1 drops the bluetooth connection and disconnects from the handsfree. Bluetooth itself is staying on on the X1, so I need to take out the key, redo the ignition and restart the car so the phone reconnects.
Does anybody know what this could be caused by or what to do about it?? Already tried re-pairing, without success.
Thanks lots for your help,
valentin
Dear All,
I am facing the following problem. Whet I gen an incomming phonecall while on bluetooth with BT device connected (car, headphones) the conversation always starts from the phone, not from the connected device. I have to change it manually. How can I make when I pick up the phone to start the conversation through the connected BT device?
Thanks in advance,
I have the same problem. Bluetooth headphones connected, always have to be selected manually, even when making a call through the Google assistant