Related
I will soon be opening up my phone (T-mobile Pocket PC Phone Edition) to replace the glass screen with a new one ordered online. I've never even opened the phone before and was wondering if someone has performed this operation before. I would really appreciate any pointers, tricks, cautions, pictures, etc.
Thanks.
lawrence... where did u get the replacement??
i wonder if they got replacement cases! i chiped mine
The company I bought the screen from was GetHighTech, Inc, in California. By coincidence, they are about an hour's drive away from my home.
They only sell the glass screen and high capacity battery replacements. The screen comes with absolutely no documentation or instructions. I just got it a few minutes ago.
just wanted to see if you had any luck with the changeout.
Screen replaced successfully: observations
It was a tricky operation, but I finally managed to replace my broken touch screen. And the patient is alive, and only a little worse off for the experience.
I was held back for a week until I could get the right size torx screwdrivers to remove the back cover. Once inside, it was a very very tricky process slicing off the broken screen with a razor blade. It was glued to the lcd display. This would have been hard even if the screen was not shattered. Definitely needed goggles to protect against flying splinters of glass. I used cotton swabs and 99% alcohol to clean the glass dust off the glue around the edges of the lcd, then I put the new screen on while that residual gum was still a bit tacky.
There was a very thin existing plastic cover over the lcd in between the glass touch screen and the rest of the lcd. Since it did not come off with the glass, I left it in place even though it had a couple of small scratches from contact with the broken glass. It seems like it was there to keep dust off the lcd or something like that.
This was my first time inside the phone. I noticed that replacing the whole LCD component would have been a trivial task by comparision to replacing the glass alone. And even easier would have been adding a new battery.
cracked lcd on xda
hi, does anybody know where i can get a replacement for the lcd screen on my xda... its totally mashed and i need to unlock it but the screen is bad...
i live in uk... any ideas guys..
pls help out
has anyone give me pls an idea how much a new replacement screen for XDA might cost
currently I am having two XDA (one XDA and one MDA), MDA has a broken screen ... I'd like to know how much is the material (screen), I have so. to do the actual job of screen replacement
regards, monika
I replaced my touchscreen a few weeks ago. Like Lawrence said it's a little tricky and you need to be patient.
I bought my touchscreen from www.pdasmart.com/pdaphone.htm for $75 and they gave great instructions.
thank you for your kind answer
hmmm, seems like it is nice to live in US ... where all the things for XDA are almost readily available :wink:
regards, monika
Protective Acryclic Cover over the Digitizer
I have an odd problem. I have an SX56 with a broken protective cover. The protective cover is the acrylic sheet that sits between the digitizer and the outside world. Everything else works fine including the digitizer. I have found every replacement part except that cover. I've even tried local plastic stores. They don't carry the proper thickness (0.125mm).
Any thoughts or sources besides sending it in for a $200 repair?
is this housing http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=260453968402&ssPageName=ADME:X:RTQ:US:1123 a FURTHER rip-off in quality as the OEM found here http://cgi.ebay.com/OEM-SONY-ERICSS...ries?hash=item2ea6dd8d1e&_trksid=p3286.c0.m14
i want to buy a new housing but i don't wanna buy one with less quality than the original
what are your thoughts on the pics there?
Judging by the pics both fascias seem identical. Although don't know why this big pricing difference. Maybe the first auction is for a replica housing? Don't have large pics as the second auction so we can tell for sure.
Also, at CNN http://cnn.cn/shop/sonyericsson-xperia-c-28_638.html the housings are pricey. For me go for the second auction or buy from CNN, you will be 100% sure that the housing is the OEM.
yeah i was looking at the $24.00 on ebay too... someone should buy it and tell me how it is
i think im gonna let this pass and sell my x1 as it is, im thinking of leaning towards the touch diamond 2 i will miss my keyboard but what the heck
Yo!
I ordered the $24.00 last week... When I receive the housing parts, I will take pictures and spread the message....
Fingers crossed......
Damn the cracks....Its a pity to sacrifice a gd device just now that some gd new things are coming....senseUI....Leo...sure it'll come for d2 too.....but no KeyBoard there.....I have ur very same problem...but I'll try the case !!
Received the housings yesterday.
They're certainly not OEM (maybe the backcover is, the rest not). The outside looks quite nice finished, the set is quite complete (with some tools for the fitting). From the two sets I ordered, one has a large gluestain on the top part of the housing (below the LCD). This gluestain damaged the paint. So I decided to start transferring the phone in the other housing.
After dissecting the phone I started with the assembly of the screen part. The speaker fitted not quite nice, so took some feddling to get mounted. At last it fitted (the print on top of the speaker fitted just). Closing the top part of the housing was a mess. The snap-locks didn't snap (partly) and on one side the housing did not flush fit. The (original) screws did not fit in the thread bushings.... With some fiddling I sort of managed to fit them. Then on with the bottom part. The new chrome buttons do not fit in the new chrome housing part.......
This is were I give up for yesterday. I think I'm going to rebuild the old housing en give up on the new one....
So.....
Decide for yourself if it's worth the trouble.... The housing looks quit neat (not as good as OEM though) but the fitment process is quite troublesome. Delivery was fast and the package is complete (including self-adhesive rubber for screen and speaker fitment). I will get in touch with the guy from Ebay with my findings.... Maybe I'm doing something wrong....
Will post some pictures tomorrow or something....
thnx ur comments were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx, ur comment were of gr8 benefit to me.....will be gladly w8ing for the pics !
thnx dude, im waiting on mine to be delivered,
looking forward for more reactions...
@Fliptil
From a scale from 0-10, how hard was it to do?
Before starting myself, I want to know if i'm capable of doing this.
To be honest, I know how to fix stuff, but don't know if I can do this trick..
Thanks for sharing anyway
Does anybody know, where i can buy a non branded battery cover for my sliver x1?
It is branded with T-Mobile, but i would like to have it blank or non-branded.
An original one is 25 € in ebay Germany. That's too much. So a cheap one would be fine.
Thanks in advice for all tips!
Best regards
Jog
ebay dude, i purchased one 2 weeks ago for about 10 GBP
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=170363212269
OK guys....
I managed to revive the Xperia tonight.... It has become a hybrid with the metal (original) front and black backside. The middle part is also left original. So the only part I ended up exchanging has been the back cover.
First of all; kudo's to HTC for making the Xperia somewhat sturdy (at least the inside is...). The amount of mechanical havoc tha has been put through the innards of the phone are substantial... And still everything functions!!
After the initial assembly attempt a few weeks ago, I was sure that I had wrecked my phone trying to assemble it with the new housing. Some parts did not fit really well, and the (original) screws did not quite fit the (new) threaded bushings. Halfway through the assembly process I ran into the new chrome buttons not fitting in the new chrome middle part and I gave up on assembly for the time being. After recharging myself for a couple of weeks I forced myself to take up the task of finishing the assembly of the phone tonight...
First I had to disassemble the phone (I was halfway assembling it...) again. I decided to use the original front (had some scratch damage and a very small crack) to surpass the not-fitting thread bushings in the new part. This was a problem... One of the screws had settled in the not-fitting thread bushing and decided to not unscrew, but turn the bushing in the plastic instead. After trying careful and not damaging anything for some time I decided it was time for the hobby knife and screwdriver (as crowbar...). The new front cover did not survive this operation. The screw and the innards of the phone did however!! Reassembly using the old front cover was quite easy, as was reassembly of the back using the original middle part. In the new back part was the thread bushing missing for fixation of the speaker... I used the not-fitting bushing from the front cover as bushing for the speaker fixation. Off course after I made the bushing fitting by forcing the screw in the bushing using a sturdy screwdriver and a set of pliers. This bushing was hammered (carefully...) into the location where the bushing should have been.... This sort of worked. The new back cover does not fit as neat into the original middle part as the original back cover, but it did fit (with some force). The plastic lip that fixes the SIM card was a bit to long, so I had to cut of 0,5mm to make it fit the SIM card. And last but not least only one of the two new battery covers was able to get a grip on the phone...
Then came the thrilling moment to switch on the phone.... Everything worked as if nothing had happened!! So end good all good; I have a phone that looks quite neat (part brushed metal - part black) and functions.
If it was worth the hassle... I doubt it... When you've got a phone that is in pieces and you want spare parts to repair it (as cheap as possible and you like some hobbying) then go ahead and buy this housing. If you want a phone that looks as good as new (and you don't want to risk a heart attack or nervous break down) then I guess you're better off leaving this housing as it is.... For a phone that's worth a few hundred bucks I think this housing is not OK. For a scrapheap phone that needs revitalisation for a small amount of money than it's OK.... If I had to do it all again I think I would have gone for an OEM housing.... After all, I'm happy that my phone functions again so I can leave the TYTN at home. I was to stubborn to buy another housing...
This has become quite a story, hope it will be of any help to somebody. Now I must see if I can post some images....
Grreetz,
Ronald
Some pictures.... try if it works....
Hmm i've dropped my poor x1 on the concrete sidewalk as i got out of my car.
Amazingly it must be good quality because there are a only a couple of scratches on the front and some damage on the rubber around where the
stylus is, but otherwise everything works and is functional.
What this experience did, was got me lookin for spare parts in case I'd
ever need them. As a result I ordered from the same person on eBay 2 days ago
and I just now found this post. Needless to say, I'm damn scared that I've
wasted the money. You tried to fit the black parts on a silver X1, and mine is black,
so I'm crossing my fingers that for some unknown odd fantastical reason, it fits better on the black version. Also may ask whether your model is an x1i or x1a?
I'm guessing b/c its silver its an x1i but u can nvr be to sure. As for me, mine is
a black x1a. I'll post back if i have any updates.
Hi Nick.
I've got a X1i, as you had already guessed.... The mixing of the parts is also a bit of a risk.... The chrome middle part (original) has suffered some damages during my disassembly actions to start with... And has developed some new cracks in the use as a hybrid. Maybe I've overtightened some screws, or maybe the bottom part does not fit well enough so it develops to much tension I don't know...
I've decided to use the X1 till it dies, and to buy something else (no slide keyboard) a little bit more sturdy when it does. I am not going to do any repairwork on it. The design is simply flawed, I have had it repaired at SE once, when it came back it was broken again within two months. These stories can be found al over the internet, so I am not going to repair it again (just to get it broken again). I am not careful enough for a phone like this (however, my colleague also has a X1 that's broken and he is very careful...) I guess.
Just my two cents.
thanks fliptil I'll keep those things in mind.
Before i dropped my x1 for the first time. There was some kind of defect in the silver middle part. At first it was a slight crack so i thought nothing of it, until a piece fell right out of it. Until now i've never needed to go through the process
of getting something fixed and was my experience painful. I got mine through a carrier (Rogers) so I called them on the phone. I was on hold forever, and when I finally got through they told me I had to go to a rogers store to have someone
personally take a look at it.
I got to the store, got on their phone, and was on hold for 20 minutes. When I got through they told me they would connect me to a specific department.
Another 20 minute wait.
I got through and then gave the phone to a rogers employee there. He confirmed that it should be a defect as there were no signs of dropping it and then HE waited 20 minutes while the guy on the line called sony.
I waited all that time to find out that I cannot get it replaced through my carrier but had to go through sony themselves.
I looked up some stories of experiences with SE's services and found that most (if not all) of the time they replace your x1 with a refurbished one, and I wasn't about to trade a perfectly brand new one with a minor ding in it, for
one that could be potentially scratched up and badly treated.
Now that I've dropped it though I fear that whether the defect gets worse or not I cannot get Sony's warranty on it. However, after what you've just told me I don't think I want to. Here's to hoping that i won't have to do x1
surgery anytime soon...
My camera lens has cracked. I know it can be peeled off, but I want to try to find a replacement. Does anyone know where I could order this part to put it back on myself? Ive done quite a bit of looking on google, and havent found anything solid.
Thanks!
OEM HTC Droid Incredible Camera $22.99
Only problem is it looks like you have to buy a minimum of 3.. cheap enough that you could probably sell the other 2 on Ebay or to someone on here who wants a spare..
If you look at the other cameras they sell, they are the photo units themselves, not the lens. I would say 22 bucks is more likely the price for the camera unit. Very nice find though!
Maybe you can call them and findout if they info on that.. odd that they wouldnt have the lens when they have almost everything else..
Global Direct Parts Tel: 1-210-444-9469 e-mail: [email protected]
A coworker of mine had his lens cover "push in" to the housing and VZW replaced it for him.
Well I don't have insurance, and the lens is cracked, not just pushed in.
He didn't have insurance either...
What do you have to lose by calling VZW and asking them? A wasted 5 minutes?
they even replaced my bricked phone for free with overnight shipping......
I got the red development cover off EBay. It came with a new back plate that has red buttons and a silver camera ring.
I'm not sure if I'm going to try replacing it or not... But would have an extra lens cover if I decide not to.
If it has the lens and all still in it I will gladly paypal ya for it.
Looks like that globaldirect place added a part.. this coujld be it if you are still looking for it.
http://www.globaldirectparts.com/HTC-Droid-Incredible-Camera-Bezel-p/htc738845.htm
That looks to be the part. I'm ordering 2 and will update with what they are exactly.
can you update with what that part is exactly? i'm thinking about trying to change mine out and would be nice to know exactly what i'm getting before ordering. i e-mailed them but haven't gotten a response yet...
mainly i'm interested in knowing does it come with the glass too, or is it just the bezel?
Anyone find a camera lens cover glass part yet?
Got the lenses in finally. Sorry it took so long, I was out of town on business for a bit. The glass lenses are included with the bezels, but there is no foam bumper like the stock lens. I keep my phone in the Speck case so that really isnt an issue. The lenses are protected by a plastic film which was nice. If anyone has any questions let me know. One concern i do have is glass seems to be off center on one of the bezels i received. I am going to contact them about that.
Any updates? Mine fell off but the camera still functions well. As much as I love the phone, I'm beginning to see just how cheap it is.
it seem like my DINC camera lens are coming offing too. if i pressed little bit harder, it will popped right inside.....
I have a loose lens, as well...
Love the Dinc...hopefully the dinc2 will be a little better quality...
If you have a tiny bit of skill you can make one out of any thin piece of clear plastic. Grab an old boombox or phone or something you don't use anymore with clear plastic and then grab your file and get to work. Free fix.
hi everyone so i managed to break my hd2s screen yeah i know it sucks.. right now im in the process of changing the digitizer for a new one i bought off of ebay.. i took the phone apart that was pretty simple but while doing so i removed many glue copper like stickers and also adhesive strips specially the one holding the digitizer and the lcd together.. my question is if anybody knows where i can buy the adhesive strips.. and most important the cooper like tape since it was covering the sides and the back part where the battery goes.. has anyone been successful at fixing their broken hd2 and is the copper-like tape important.. or can i just use some regular hot temperature resistant tape? well thanks in advance for the help
I know this doesn't really help you with your situation in any way but. I broke mine as well, and i just decided to let the insurance company handle it. I know it's expensive 130$ compared to the 50$ you could buy a new screen for. But they send you a brand new sealed in box phone, next day air shipping. I've only seen one video on how to replace the glass, and it was for the euro one, and it required, basically, completely disassembling the entire phone.
Sorry for the non-help. Just my .02c
i broke the one on my blackstone bought one off ebay pretty cheap but i couldn't put it together ,i ended up paying $50 get it installed the right way
hi,
I have a crack line on my Samsung Captivate screen and I've been researching on how to replace the front lens without replacing the entire LCD assembly because to be fair the LCD is still good and all that needs replacing is the front glass.
Anyone seen anything or know anything about disassembling the LCD module?
i believe its all one unit glued together. thats why none of the ATT boys have been able to remove or scratch off the ATT logo
75 to 139 bucks on ebay
but like glue can be seperated right? Like has anyone tried giving it the heatgun treatment? I'd do mine but I dont have a replacement yet so I don't dare try
not recommended, with that kind of heat the plastic wraps and it will not fit anymore, change the whole screen, its the easiest way
well... that pretty much kills it...... i'll most prob buy a replacement LCD. But I am genuinely curious about it and I guess when the new AMOLED arrives I guess I'll have something to play around with......
anyone tried dissolving the glue?
well I smashed my lens on front of my screen and I notice that they sell the lens only on ebay now, has anyone found a way to check the lens only yet?