Related
I am having the strangest problem. Everytime I turn my phone off and on again the dialer starts up along with the wifi settings. On top of that none of the buttons work except the middle directional pad, power and camra button. I have no idea what is wrong. One day everything is fine then the next its not. Any help will be appreciated.
Hard Reset
I just reflashed and the problem is still there. Except now instead of the wifi setting I get the ringtone creation tool and it creates a new dogbark midi file everytime I turn my phone on and off.
Any help? I have reflashed 3 times now.
If you've done a hard reset and it still does it, it's pretty much a hardware fault by definition. Return to vendor!
hicks said:
If you've done a hard reset and it still does it, it's pretty much a hardware fault by definition. Return to vendor!
Click to expand...
Click to collapse
Not true at all. If you were to flash to another ROM, I'm prtty sure it'd be gone. It's more than likely a softare related issue and check your start-up folder to see what it has there.
I was, perhaps incorrectly, assuming the OP was on original ROM as he didn't detail what he had changed to
I was on L26 diamond V4 when it started up. Then I flashed to V9....then I restored all my settings and rom back to the original ATT and I am getting a new replacement phone today lol Thanks to everyone who responded.
dtjunkie07 said:
I was on L26 diamond V4 when it started up. Then I flashed to V9....then I restored all my settings and rom back to the original ATT and I am getting a new replacement phone today lol Thanks to everyone who responded.
Click to expand...
Click to collapse
ouch... I don't think that solution will work for me.
Mexy
same problem here with L26 v12 the hardware buttons sometimes don't work they work fine after softreset!
Okay, so to those of us who have problems with screen ignoring/being very slow with screen taps and/or buttons, read on.
I flashed ROMeOS ROM and started having problems where I would tap on something, and it would ignore it. I would keep tapping and tapping, but nothing happened. Sometimes, even hardware buttons were ignored, about 40% of the clicks. I never had that problem with Dutty's Diamond ROM or WM6 ROMs. Issue seems to be related to latest 6.1 builds... or so it seemed at the time.
After pulling out half of my hair, reflashing all kinds of ROMs, reflashing to latest HardSPL, etc etc... I almost threw my kaiser at the wall.
First I thought it's TouchFLO, then I thought that it's the latest 6.1 ROMs.. then I thought it's related to 3.56 HardSPL.. well eliminating those factors one by one DID NOT fix the problem. Right now I went 100% to stock ROM (one it came with) and AT&T's original SPL. I started having sound problems (w/e radio I tried did not work) so I flashed Hyperdragon Wm6.1 ROM.
About 90% of the problem is phone ignoring ANY kind of touchscreen taps/drags.
About 10% of the time its the hardware buttons that have the problem - for example I push "call" (or any other softkey) button, and nothing happens, while touchscreen could be working fine at that time. In about 10 seconds, hardware buttons would start working again.
Some information that was gathered from this thread and personal research:
It looks like problem is NOT related to the following:
- POWER. Connecting phone to AC power does not solve the problem. Subjectively, it may improve it a little.
- BLUETOOTH/WIFI. Problem persists with EVERYTHING disabled and phone being in Airplane mode.
- PARTICULAR 6.1 ROM. I had this problem on ANY 6.1 ROM I tested (and I tested all the way from AT&T almost-official WM6.1).. maybe that's why they didn't release it?
- OPERA browser. Some people never had Opera and they still have this problem (please confirm this!).
- SPB/WISBAR interface software. Although having Wisbar stuff does make it a lot worse for me.. and I still have the problem without SPB or WISBAR installed.
- S2U2 screen lock. Still had the problem w/o S2U2 installed.
- iGo 2006 or iGo 8. Many users with this problem never used iGo.
Problem MAY be related to the following (needs more research, please help):
- Original SPL versus HARDSPL 3.XX
- WM6.0 versus WM6.1 (I don't think I had any problems running original AT&T 6.0 ROM, but I did have sound (radio) problems, so had to flash 6.1). Several users report that WM6.0 is immune to this problem.
- A combination of running WM6.1 with latest HardSPL?
- Custom ROM VS Original ROM. Perhaps problem is in the tweaks to the registry.
- Simple things like overtime connection weakening in touchscreen connection to the mainboard. Whoever can open a Kaiser could try to replug/clean it and report back to us.
- Radio version. Should be easy to test, just need to reflash all kinds of older radios and see if problem persists.
Please make sure that you test your phone with some touchscreen intensive games/software a lot for AT LEAST 3-4 days. I had it happen several times where it would be fine after reflash for about a day or so, and then it would come back in full force.
BRICK?
In my case, running HTC WM6.0 ROM with HTC SPL DID NOT fix the problem, I can even say it made it worse. Touchscreen would respond to about 10% of the screen taps. Tap pressure doesn't make any difference.
Also, running AT&T stock shipped ROM with stock shipped radio and SPL did not fix it. I guess at this point, nothing will. Waiting for replacement tilt.
Hope nobody else will get it as bad as I did. All I can say is... make those relfashes count.
Hmm isn't Touch Flo one of the cool things with the Kaiser??? How do you navigate in programs now it's disabeled?
DarkDvr said:
Okay, so to those of us who have problems with screen ignoring/being very slow with screen taps - I think I've found a fix. Here's a little background:
I flashed ROMeOS ROM and started having problems where I would tap on something, and it would ignore it. I would keep tapping and tapping, but nothing happened. Sometimes, even hardware buttons were ignored, about 40% of the clicks. I never had that problem with Dutty's Diamond ROM or WM6 ROMs. Issue seems to be related only to latest 6.1 builds.
After pulling out half of my hair, reflashing all kinds of ROMs, reflashing to latest HardSPL, etc etc... I almost threw my kaiser at the wall.
So if you have similar problems - try using Shnaps' Advanced Config to disable the TouchFLO altogether.
Another thing that I've used is PocketMechanic to clean up the notification queue. After fresh install of HypreDragon (latest as of Aug 5), I had 46 duplicate notifications. Removing those seemed to ease the problem, but NOT fix it. Disabling TouchFLO seemed to finally fix it.
I hope this helps somebody. I'll update this thread if I keep having this problem..
Click to expand...
Click to collapse
Thanks for the head's up! I'll definately try that tomorrow (danish time).
Foxhunter123 said:
Hmm isn't Touch Flo one of the cool things with the Kaiser??? How do you navigate in programs now it's disabeled?
Click to expand...
Click to collapse
Never really caled for it, I use my hardware buttons (D-pad) to scroll, I find TouchFLO to be too unreliable... maybe it's just me, but nothing beats a hardware button which you actually "PUSH".
spip72 said:
Thanks for the head's up! I'll definately try that tomorrow (danish time).
Click to expand...
Click to collapse
Do you have the same problem?
Hello,
First off thak you for the post. Ive got two identical Tilts both with the exact same radio/boot/roms. One has this issue and the other doesnt. I will be disabling it on the one havong the issue and report back! Thanks much!!!
I was also having this problem. my biggest complaint was my keyboard was all over the place. Sometimes it wouldnt see key strokes at all, other times one key hit would register as 3 or 4.
Sent a few test messages and This seems to have helped.
THANK YOU!!!
My Kaiser was getting close to being flashed back to a WM6 rom or quite possibly embedded in a wall.
where do you find cab for touchflo? I was looking for that but could not find it.
tamkhanh said:
where do you find cab for touchflo? I was looking for that but could not find it.
Click to expand...
Click to collapse
seek and you shall find.
It's all over the place.
Try playing around with the TouchFLO sensitivity options in KaiserTweak
i upgraded to official 6.1 about two weeks ago...
i recently started having the "missed taps" problem...
i have a feeling that KaiserTweak has something to do with the issue...if memory serves, i don't remember experiencing the issue BEFORE i played with the "TouchFLO->Sensitivity" and "TouchFLO->Finger Pressure" options...i just launched KaiserTweak right now and its showing those values as set to defaults where as i could've sworn i changed them to the advised settings a day or two ago approximately when i started experiencing the issue...just a point to clarify, i was only playing around for no particular reason and my taps were not problematic before
i've just changed them to the advised settings and did a soft reset to see if these are the kind of settings that are forgotten after a soft reset...but they stuck...so i'm gonna observe this for a couple of days with the advised settings effective and see if they have reverted to defaults on first sight of the issue...i'll report back here if that happens because that would be a pretty strong correlation...almost enough to prove cause and effect
Well, problem is, last time I've used KaiserTweak was like a year ago, so my touchscreen problems cannot be linked to KaiserTweak. I don't even have it on my tilt.
Also, it's definitelly not a touchscreen itself, since this problem is application-dependent. Once again, S2U2 and Opera are immune to this problem. Windows' build-in apps (file explorer, bottom bar, etc) all suffer from it.
I've noticed this too, but I've found a slightly longer tap seems to make things reliable for me.. Instead of a quick 'jab' if I sort of touch it, it seems to be better.
and keyboard too I've noticed.. I mostly notice it with the hard keys rather than the keyboard, but I don't use the keyboard a lot.
I'll try looking for duplicate notifications, what else will do that besides MemMaid? I might reinstall it, it was handy. I previously found phoneAlarm would grow notifications over time, I suppose I need to watch for that anyway.
khaytsus said:
I've noticed this too, but I've found a slightly longer tap seems to make things reliable for me.. Instead of a quick 'jab' if I sort of touch it, it seems to be better.
Click to expand...
Click to collapse
True, if I keep pushing on the screen button, in about 5 seconds it will be clicked. But that's ridiculous, i gotta say.
I'll try looking for duplicate notifications, what else will do that besides MemMaid?
Click to expand...
Click to collapse
I use PocketMechanic - good stuff. Has lots of useful functions, including notification queue cleanup and analysis.
Just had another "seizure" - touchscreen would not respond AT ALL for several minutes. No matter what or how I tap - complete ignore.
After couple of minutes it started working again.
Interesting that S2U2 worked fine. Seems that windows just chooses to ignore touchscreen input.
I'm forced to return to WM6.0 ROM...
Please, anybody look into this.. phone is becoming to be unusable - I can't even enter a phone number.
DarkDvr said:
Do you have the same problem?
Click to expand...
Click to collapse
Yeah it's really bad here. I've tried all sorts of tricks, including:
Re-install 6.1
Re-install 6.1 with the recent radio update found on the e-club
Install SPL 3.56
Disable HTC today screen
Kaisertweaks - tweaks on and off
Disable radio completely (seems to help, but makes the device useless)
Disable activesync
Disable quickgps
For now, I've done 2 things that seems to help:
- Disable the HTC task manager - improves the responsiveness
- Kill the MSTLI.EXE process - improves on the number of freezes
But I still experience freezes, and it's really getting to me. I need a responsive device, not this c****
ASCIIker said:
i upgraded to official 6.1 about two weeks ago...
i recently started having the "missed taps" problem...
i have a feeling that KaiserTweak has something to do with the issue...if memory serves, i don't remember experiencing the issue BEFORE i played with the "TouchFLO->Sensitivity" and "TouchFLO->Finger Pressure" options...i just launched KaiserTweak right now and its showing those values as set to defaults where as i could've sworn i changed them to the advised settings a day or two ago approximately when i started experiencing the issue...just a point to clarify, i was only playing around for no particular reason and my taps were not problematic before
i've just changed them to the advised settings and did a soft reset to see if these are the kind of settings that are forgotten after a soft reset...but they stuck...so i'm gonna observe this for a couple of days with the advised settings effective and see if they have reverted to defaults on first sight of the issue...i'll report back here if that happens because that would be a pretty strong correlation...almost enough to prove cause and effect
Click to expand...
Click to collapse
My device is currently without kaisertweaks, and I still have the freezing issues.
DarkDvr said:
Well, problem is, last time I've used KaiserTweak was like a year ago, so my touchscreen problems cannot be linked to KaiserTweak. I don't even have it on my tilt.
Also, it's definitelly not a touchscreen itself, since this problem is application-dependent. Once again, S2U2 and Opera are immune to this problem. Windows' build-in apps (file explorer, bottom bar, etc) all suffer from it.
Click to expand...
Click to collapse
I concur, it is application specific. I tried to run the "Task manager" from Fdcsoft to see if it was related to a process eating up all the CPU. But the problem doesn't occur while the application is focused.
DarkDvr said:
Never really caled for it, I use my hardware buttons (D-pad) to scroll, I find TouchFLO to be too unreliable... maybe it's just me, but nothing beats a hardware button which you actually "PUSH".
Click to expand...
Click to collapse
TouchFlo is way too unreliable to me too.
DarkDvr said:
True, if I keep pushing on the screen button, in about 5 seconds it will be clicked. But that's ridiculous, i gotta say.
I use PocketMechanic - good stuff. Has lots of useful functions, including notification queue cleanup and analysis.
Click to expand...
Click to collapse
Oh wow, not a LONG PRESS, literally a 'touch' vs a 'tap'. What you describe would be seriously annoying.
Thanks for the suggestion, I'll look at it
hey guys, not sure whats going on, but my tilt lately keeps freezing, but it only freezes when i go into landscape mode. i've ran the same programs for a long time (palringo, google maps, live search, kaiser tweak and srs wow) i'm not even running skyfire anymore, and i've uninstalled my opera browser but it keeps freeze. i've done some reflashes and hardware resets, and only ran the above programs, and it still ends up freezing when i put it into landscape. Anyone know what could be causing this? it doesn't matter if im typing landscape in notes, palringo, PIE or anything else, always freezes. The ironic thing is that if i bust out my stylus and type w/ that using the soft keyboard it seems to run just fine (but slows me down A LOT). any help would be much appreciated.
Do you mean your hardware keyboard lags?
If so in software is a speedup keyboard .cab.
stylez said:
Do you mean your hardware keyboard lags?
If so in software is a speedup keyboard .cab.
Click to expand...
Click to collapse
no its not a keyboard lag by any means, the phone literally freezes. i dont even have to type when its in lanscape mode for it to freeze, as soon as the screen changes orientation it freezes immediately
simbadogg said:
no its not a keyboard lag by any means, the phone literally freezes. i dont even have to type when its in lanscape mode for it to freeze, as soon as the screen changes orientation it freezes immediately
Click to expand...
Click to collapse
Thanks for clarification, just that you say soon as use onscreen keyboard no issue, are you using a stock ROM? Does it happen on a clean flash no programs installed?
stylez said:
Thanks for clarification, just that you say soon as use onscreen keyboard no issue, are you using a stock ROM? Does it happen on a clean flash no programs installed?
Click to expand...
Click to collapse
sorry, i should have given a lot more info, but i had to jet to class. Anyways, its not the stock rom, i'm running NATF's Lite rom (no TF3D). I actually downloaded originally around september/nov/dec of 08 (dont remember, but its been months that i've been running it). And never had a problem with it...now all of a sudden it seriously craps out everytime i run it. I tried running Hyperdragons IV Lite and i was experiencing some of the same problems. I'm really starting to think its one of the problems i'm running, so i'm going to to a hard reset (again) and see if it runs just palringo, and google maps w/out any problems. its just getting super frustrating to be honest. i'm running the exact same programs that i've ran for the last year, but now its deciding to act up. hopefully its something in the software and not hardware
ok...so i got home, and installed the OEM att tilt rom. really, no matter what program i install, pretty much anything. the freezing occurs. any out there familiar w/ cell phone hardware? i'm thinking that might be the cause, if so...do you think there's anything that can be done/replaced to fix it?
Hi, this started happening to my just today also! At first I thought it was the onscreen keyboard that made my phone freeze (as I have seen others with the same issue) and thought I could fix it by using another keyboard app. I used SPB's keyboard and it prevents my phone from freezing and I'm able to type things using it. BUT my phone STILL freezes when I put it in landscape mode and try to type something. It freezes after typing a couple of letters. This is stock ROM; I've never flashed it.
Is there a .dll I can use to repair or anything of the sort?
Btw, I'm using a Tilt. Thanks!
anyone have any method ..to prevent this problem???
I find that if restart the phone few times will freeze at gray screen .."the original HTC gray blank screen with loading box in the middle" but the antenna reception green light is normal blinking (all the button not functioning).... -solution have to press reset button below ...
so now everytime install new program very scare to restart .. if un lucky ..will stuck at that screen.... really wonder why ...is it the WM6.1 not stable???
I use motorola linux ..no such problem...
simbadogg said:
i'm running the exact same programs that i've ran for the last year, but now its deciding to act up. hopefully its something in the software and not hardware
Click to expand...
Click to collapse
Try the relevant ROM thread also look at your hardSPL version. Some users have fewer freezing probs just by updating hardSPL.
tsfatt said:
so now everytime install new program very scare to restart .. if un lucky ..will stuck at that screen.... really wonder why ...is it the WM6.1 not stable???
Click to expand...
Click to collapse
Not at all, there's definitely something wrong with your setup if it wont even boot fully. Maybe a hard reset and some testing between installing each individual program will weed out the culprit. That said I've found (at least the HTC official) WM 6.0 ROMs to be much more reliable and stable than WM 6.1 ROMs.
Flying Kiwi said:
Try the relevant ROM thread also look at your hardSPL version. Some users have fewer freezing probs just by updating hardSPL.
Click to expand...
Click to collapse
Sorry if it's a dumb question, but is there a HardSPL update for OEM OS?
DaDragonChild said:
Sorry if it's a dumb question, but is there a HardSPL update for OEM OS?
Click to expand...
Click to collapse
Not as such - hardSPL is made by dedicated folks who have customised the OEM version but installing it will mean you no longer have an 'official' setup. That said, you can always revert to the official HTC SPL if needed for eg a warranty return. You could also install a newer HTC SPL for your ROM (as long as it's compatible *be careful about this* - eg I'm using the 1.93 HTC SPL with my ROM instead of the 1.56 SPL). This is all explained in the Kaiser wiki (through the xda-wiki button above) so it's well worth having a good read there
aaaahh I looked around. and I can't find a driver to reinstall for the hardware keyboard... I'm assuming this would fix it~
Sorry to double post but I just wanted to say I fixed the problem by backing up and restoring with SKTools after doing a hard reset. It makes me think, what exactly caused the problem in the first place if doing this fixes it? Is there anything that SKTools leaves behind in an All System backup? Perhaps something messed with my registry causing the keyboard to freeze the phone when used.
I'd hate to think my phone can actually get spyware now. Maybe Skyfire's true desktop viewing of webpages allows for this to happen?
Let me know what you guys think
" used Spb's keyboard and it prevents my phone from freezing and I'm able to type things using it. BUT my phone STILL freezes when I put it in landscape mode and try to type something. It freezes after typing a couple of letters. This is stock ROM; I've never flashed it."
If I will you to avoid ...uninstall this soft keyboard ... use back the original keyboard at the time being and see... if u restore back what is the diff compare to now ... If I not wrong still the same ...
FYI, I got this freezing problem is after I have install PCM kb 0.14 ...then I try install & uninstall & install ..and need to restart the phone ..2 out of 4 time is freeze at loading screen .. now really worry is it b'cos I uninstall it at the same time have remove certain original files .....
WM is diff with windows ...lack of tool to chk which system files damage .... I really hate hard reset ..just like computer... imagine keep format the hard disk ....
Hard reset comparible to system recovery process
tsfatt said:
WM is diff with windows ...lack of tool to chk which system files damage .... I really hate hard reset ..just like computer... imagine keep format the hard disk ....
Click to expand...
Click to collapse
If only restoring a full size PC was as easy and quick as hard restting. Sure there's a little work involved in reinstalling apps after completing the hard reset but if the apps are well designed ones that install via activesync, that's as easy as going to Activesyncs add and remove programs function and ticking a box. If this is not available then maybe the old app is the cause of the problem?
A hard reset every now and again is very useful for maintaining peak performance and it certainly weeds out whether a problem is hardware or software related pretty quickly.
Hi,
I'm unable to get GPS fix.
Any ideas?
Thanks.
its the same problem for me...
help is really needed!!!
What software are you using? I had the same problem yesterday after having used it flawlessly for a month now. Had to hard reset and it started working again.
im using GARMIN MOBILE XT. v 4.10.40wp,
this software is be used on TD1, it worked perfectly well
here guys i dont have the diamond 2 but when the fuze or touch pro released it too had gps problem and this is the fix i use maybe it will work for you guys
http://forum.xda-developers.com/showpost.php?p=2894542&postcount=1
I had this as well, waited several mins and had no results. Try the below and then things should be all well.
Run the quick gps app on the phone, that will update the phone with the sat positions. Then stand outside or by a window for a min or two and you should get them.
This is interesting for GPS problems http://blog.mohdimran.com/2008/11/htc-touch-pro-gps-problem-tweaking.html
I had problems with apparently non responsive GPS, doing all the mods in the link above has transformed it.
Also, before anything else, if it doesn't appear to work at all, make sure your software is set to look for the GPS device on COM4.
I had tried absolutely everything prior to doing a hard reset. In the end I just wrote it off as one of those quirky little things that makes this phone unique lol.
I had this problem randomly. So I checked the status of the GPS driver using Dotfred's Task Manager (Device Manager tab) (freeware at http://www.dotfred.net/TaskMgr.htm) and I found that sometimes after a soft reset it was not loaded (why I do not know) but could be loaded manually.
Therefore I wrote a little utility, DeviceStart, to load and start it.
If you have this problem copy DeviceStart.exe in \Windows directory, create a shortcut like this (or use the one inside the .zip file)
55#"\Windows\DeviceStart.exe" Drivers\BuiltIn\gpsdriver 60
and put it in \Windows\StartUp directory.
DeviceStart.exe requires .NET Compact Framework 2.
The same happened yesterday to me.. No way to get it working even after 5 soft resets, the GPS just couldn't kick in. I was genuinely scared that the GPS module broke down. Even after the hard reset it behaved strangely in the beginning, only after quick gps it finally started working. The worst thing is, if this happens again and I'm abroad where I'll really need GPS - a tought of all the hassle with data roaming etc doesn't make me exactly happy.
I'm still trying to figure out what could have caused my gps stopping working. The only thing I can think of was Clean RAM, 3rd level. Is there any chance it was caused by that? If so, would the utility (Startdevice) from 2 posts above start it again?
cassper1 said:
I'm still trying to figure out what could have caused my gps stopping working. The only thing I can think of was Clean RAM, 3rd level. Is there any chance it was caused by that?
Click to expand...
Click to collapse
Who knows! But in that case a soft reset should restore it working.
cassper1 said:
If so, would the utility (Startdevice) from 2 posts above start it again?
Click to expand...
Click to collapse
Check using Dotfred's Task Manager. It can show if gpsdriver is loaded or not and using it you can try loading it manually. If it succeed Startdevice can do it automatically.
My phone does not suceed on aligning screen and therefore the set-up does not go through.
This happens with any rom I install. I assume is more a harwdware than a software problem, because I noticed some problems in the screen touch even before.
Is there a way to by-pass it and to force WinMo to complete the set-up process?
Thanks
tecmobility said:
My phone does not suceed on aligning screen and therefore the set-up does not go through.
This happens with any rom I install. I assume is more a harwdware than a software problem, because I noticed some problems in the screen touch even before.
Is there a way to by-pass it and to force WinMo to complete the set-up process?
Thanks
Click to expand...
Click to collapse
What problem do you have? Is the aling screen proces start all over again after finishing all five steps? Sometimes I do the screen alingnment over four times. You should press right in the center of + with your stylus, and do not shake even a little bit because it will start again when you finish.
If this isn't the problem, hope someone else could help you, even that I don't believe it is possible.
Good Luck!
Cheers!
tecmobility said:
My phone does not suceed on aligning screen and therefore the set-up does not go through.
This happens with any rom I install. I assume is more a harwdware than a software problem, because I noticed some problems in the screen touch even before.
Is there a way to by-pass it and to force WinMo to complete the set-up process?
Thanks
Click to expand...
Click to collapse
not sure if it will work on x1 but worth a shot.
turn off device
plug in usb cable with PC
start device
when active sync is loaded, go to main storage\windows\startup\ and delete welcome.lnk
lev phone on like that for a good tem min. then softrest
agent_47 said:
not sure if it will work on x1 but worth a shot.
turn off device
plug in usb cable with PC
start device
when active sync is loaded, go to main storage\windows\startup\ and delete welcome.lnk
lev phone on like that for a good tem min. then softrest
Click to expand...
Click to collapse
Should work, but if i'm not getting this wrong this will also not let you run auto customizations
killer8nl said:
Should work, but if i'm not getting this wrong this will also not let you run auto customizations
Click to expand...
Click to collapse
he din mention he did a hard rest. :S....sometimes it may ask for allignment all of a sudden....my x1 did once
but if he has already done a hard rest then he has to wait 10min....should work or he could use the app (whose name i 4got ) to go into reg and delete the reg that triggers customization
PS: ill give more details when i get home n check out the app n the reg
tried to delete as you instructed.
Unfortunately he tells that I "cannot delete file welcome: access is denied"
any way to overcame it? tried also to rename or move, but with no avail
tecmobility said:
tried to delete as you instructed.
Unfortunately he tells that I "cannot delete file welcome: access is denied"
any way to overcame it? tried also to rename or move, but with no avail
Click to expand...
Click to collapse
I had the same issue tried even deleting files via third party applications and skipping align screen but once u do it your screen doesn't react for any thing you do. you cannot configure neither ur buttons too sometimes doesnt work. the best way which I found that you try any of the original ROM version ..either UK or NAM which actually resets the radio and brings back in normal stage...hope it works for you.. then you may tryu doing hard SPL and install any of the cooked rom.
I have installed indeed the uK offical version...