hi there after getting the helmi 1.3.2 wm5 rom and upgrading (latest) , i wanted to upgrade to the latest radio , i put my phone into serial mode and activesync wont recognize it it is activesync 4.2 ( i tried the beta as well) , it wont even connect while my modem is plugged in to the usb , it says acquiring network for the ppc when plugged in , it will connect once i turn my connection off but not at all in serial mode , so i cant run the upgrade any ideas??
bottom line = pc internet on - no connection
pc internet off (but modem on) - works
either of above when ppc (m2000 BA) is in serial mode - no connection to activesync
it used to work in serial on wm2003 SE (how i upgraded to wm5)
did u solve the problem?
Related
I put my pda in bootloader mode. Serial v1.00 is what i see. I plug the USB cable in it and what i see is USB v1.00. I start romupdate.exe, but it cannot see the usb connection.
What am i doing wrong? I tried it on 2 pc's, both are not working.
Any help appreciated.
Nevermind, i forgot to kill the activesync process.
i hv dopod838 wwe , installed & run the lookiwz02a ( U & C ),
but when running romupdate, with activesync usb off, still romupdate won't recognize the usb. i also tried mtty with same result, usb not recognize.
HELP guys, I downgraded from AKU2 Cingular 2.25 to the 2.17 ROM and for some reason I can't get an Activesync connection from my desktop over USB. Each time I plug the USB cable into my device I get a "USB Device Not Recognised" error.
This same error happens on more than 1 desktop so it looks like a device/ROM issue.
I've tried using USBSwitch, removing the USB Hub device drivers, reinstalling ActiveSync (4.0, 4.1 and 4.2 beta), deleting the partnerships in ActiveSync and hard-resetting the device without any success.
Without an ActiveSync connection I can't flash up to Sumitters custom 2.25 ROM so I am stuffed currently !
Please HELP, is there a way of reflashing without an ActiveSync connection, from SD perhaps ?
Any other ideas on how to get my ActiveSync working again ?
Hi,
today i have unlock the CID on Wizard / O² XDA Mini S and flash the Wizard reTouched Rom.. all is going perfectly and works great...
then i flash only the radio rom 2 47 11 from this site.. after flashing my device will restart himself.. but now USB will not work any more and the cellphone interface will not work too....
can annyboddy help? /
The sequence how to recover:
-Start in bootloader mode (reset & hold voice command button).
-Disable usb connections in active sync
-Connect wizard with usb (not before disabling usb connection)
-Reflash original factory ROM
Good luck,
EqX
hi.....
i found last night a way to reanimated wy wizzard by my self...
right the by the way as you told me now.. but thx for your answer!
I screwed my Wizard after updating radio 2.69. Reflashing didn't work, phone connection error SH*T. Downloaded the orginal tmobile rom and this upgrade connected to the Wizard. After the upgrade the Wizard was running again. Many THX!!!!!
Hey All.
I am on vacation, and just brougth a new notebook (lovely Medion Akoya), and i want to sync with my diamond. However, i downloaded the active sync from the ms homepage, and i get the "Unrecognized device" error all the time.
Yes, i tried to use different cables, yes i tried to deactivate the advanced network, however, i doesnt seem to recognize it at all.
Even if i do a softreset + volume down, i just get the SPL1-40 screen, but eventhou my phone is plugged in the USB, it doesnt say that, only "serial" when i disconnect.
I've been searching this forum the entire day, and i cant seem to find a solution. So, i kindly ask the gurus help me
Diamond running 0.95 bePe and pc running xp sp3.
Kind regards, Heien.
Try to flash a stock ROM and check if you run into the same problem.
In order to sync, you must be running the handset normally, don't enter bootloader mode.
Did the system prompt you for drivers the first time you connected it to the PC? Activesync 4.5 provides the rndis drivers.
the problem is, i cant even flash my device, i tried to flash it, but i get a connection error with the tool.
I know about the bootloadermode, and that i am not able to sync in that state, but i just wanted my pc/diamond to recognize the connection between them. The system did not prompt me for drivers, it just went straigth to unrecognized device. i even tried to point the the driverupdate tool to the drivers folder with the rndis drivers in the as folder.
-i also tried to hardreset my device.
Try doing the same on a fresh stock XP install, without firewall or anything similar.
We need to figure out if it's a problem with the handset itself or your OS/PC.
Try another USB port (DON'T use hubs).
Enter bootloader mode. When you connect it to the USB, it should at least toggle from serial to usb.
If that's the case, at least your USb is working well.
I've reading some FAQs and Wiki articles before make this question.
Last weekend my Kaiser crashed into the floor (a very very very soft fall) and the battery jumped out the phone.
I put the battery, and in the first boot.... Ooops!! Tricolor screen showing:
"Hardspl 3.29
Serial "
There is a quick splash screen showing "No image file".
I've tried to boot several times, and i get into OS once, but the pda works so slow.
Solutions that i've tried:
a) MMTY prompt. Boot command doesn't work and i dont know the "boot command" for Hardspl 3.29. Anyway, i dont want to mess with MMTY and get a brick...
b) When i get into OS i tried to connect via Activesync (to reflash Hardspl) but...
After JumpSPL I get "Jump Tricolor Screen"
I unplug usb, uncheck "USB Connections", plug USB... but KaiserKustomRuu doesnt work! It closes after executing it. (The day that i flashed hardspl 3.29 i did it the same way, and everything went ok)
What can i do?
Please help!!!
(I dont care loosing data, i only want recover the pda)
EDIT:
Hi there.
Finally i did this:
- Re-flash HardSPL 3.29 (via MicroSD)
After that, OS always booted (WM 6.0 Official HTC)
However, Activesync does not work. When i plug the usb cable, the battery begins charging and activesync runs on PDA and Pc, but PC says that connection is not possible. I've tried with 2 or 3 computers with same results.
(Allow usb connections is marked)
Also, all the OS gets so so so slow when usb cable is plugged.
Then i did:
- Hard Reset to back default WM 6.0 official ROM
* No way. ActiveSync does not connect.
- Flashing a cooked Rom (WM 6.5 spanish) and a new radio (from 1.27.12.32 that i always used with WM6.0 to 1.70.19.09)
* No way. No i have Hardspl 3.29, WM 6.5 spanish cooked rom, and 1.70.19.09 radio. Everything seems to be ok...except for Activesync.
Please...help....
EDIT 2:
Ok.... i've tried to access MTTY prompt but it was impossible.
When i plug the USB cable i get an error in the computer (device not recognized), but PDA screen changes between "serial" and "usb".
After 20 or more tries i got into MTTY prompt, but that was the last time until now.
So... i think that mi usb port is broken ( is not the cable or the computer, i used some cables and computers)
I've tried to move the usb connectors with a pin, slowly, and i have cleaned evertything, but nothing happens.
What may i do?
How can i check my flash/nand to check errors? Of course, i need to check it but not using USB !
USB port is charging the battery, and windows attempts to install the device (Windows mobile device, as says) but the installation is not finished.
So you are unable to use activsync at all on your phone?
http://forum.xda-developers.com/showthread.php?t=423486
Hi there.
Yes, i am unable to use activesync from OS.
Draelee, i will check that thread, thanks.
Hi there.
Finally i did this:
- Re-flash HardSPL 3.29 (via MicroSD)
After that, OS always booted (WM 6.0 Official HTC)
However, Activesync does not work. When i plug the usb cable, the battery begins charging and activesync runs on PDA and Pc, but PC says that connection is not possible. I've tried with 2 or 3 computers with same results.
(Allow usb connections is marked)
Also, all the OS gets so so so slow when usb cable is plugged.
Then i did:
- Hard Reset to back default WM 6.0 official ROM
* No way. ActiveSync does not connect.
- Flashing a cooked Rom (WM 6.5 spanish) and a new radio (from 1.27.12.32 that i always used with WM6.0 to 1.70.19.09)
* No way. No i have Hardspl 3.29, WM 6.5 spanish cooked rom, and 1.70.19.09 radio. Everything seems to be ok...except for Activesync.
Please...help....
UPDATED the first post.
Is my PDA - USB port broken?
I hate to tell you this.. But a work around could be to Activesync via Bluetooth... Now a days you can get a USB Bluetooth dongle for $5 or sell... My stepsons USB port is so broke that he has 3 batteries and a stand alone battery charger.. he jsut swaps batteries when it dies... He syncs via bluetooth and has no problems....
So, once you have read the entire post...
Do you think in a software or an hardware problem?
Bluetooth sync is a good option, but i would like to investigate a little.
I've reflashed HardSPL, ROM and RADIO but i think that there are more bad data sectors.
How can i check my flash/nand to check errors? Of course, i need to check it but not using USB !
USB port is charging the battery, and windows attempts to install the device (Windows mobile device, as says) but the installation is not finished.
Thanks!!
Try flashing an Android ROM
Hi,
I had the same problem on my phone for about 6 months. I completely gave up on it. A few days ago I successfully flashed an Android ROM to NAND but ended up flashing back to WinMo. Surprisingly my USB activesync / headset adapter started working again!!
I'd give it a shot if I were you. Worked for me
~Joe~