HELP guys, I downgraded from AKU2 Cingular 2.25 to the 2.17 ROM and for some reason I can't get an Activesync connection from my desktop over USB. Each time I plug the USB cable into my device I get a "USB Device Not Recognised" error.
This same error happens on more than 1 desktop so it looks like a device/ROM issue.
I've tried using USBSwitch, removing the USB Hub device drivers, reinstalling ActiveSync (4.0, 4.1 and 4.2 beta), deleting the partnerships in ActiveSync and hard-resetting the device without any success.
Without an ActiveSync connection I can't flash up to Sumitters custom 2.25 ROM so I am stuffed currently !
Please HELP, is there a way of reflashing without an ActiveSync connection, from SD perhaps ?
Any other ideas on how to get my ActiveSync working again ?
Related
Hi,
Does anyone know how I can upgrade to 2.25 if ActiveSync is not working.
Long story but I get a "USB Device Not Recognized" when I plug my device in and I've tried all-sorts to get it working again.
I'm resigned to having to flash the ROM from SD (Cingular 8100), does anyone have instructions and the requisite binaries to do that ?
HELP !!!!!!
try and install the new active sync 4.2beta and then reboot then try and put your device in. But do not put your device in until after you've instlaled and rebooted.
exstatica said:
try and install the new active sync 4.2beta and then reboot then try and put your device in. But do not put your device in until after you've instlaled and rebooted.
Click to expand...
Click to collapse
Tried that, every time I plug my device in the PC it report "USB device not recognized". Tried multiple PC's and multiple cables
Hey All.
I am on vacation, and just brougth a new notebook (lovely Medion Akoya), and i want to sync with my diamond. However, i downloaded the active sync from the ms homepage, and i get the "Unrecognized device" error all the time.
Yes, i tried to use different cables, yes i tried to deactivate the advanced network, however, i doesnt seem to recognize it at all.
Even if i do a softreset + volume down, i just get the SPL1-40 screen, but eventhou my phone is plugged in the USB, it doesnt say that, only "serial" when i disconnect.
I've been searching this forum the entire day, and i cant seem to find a solution. So, i kindly ask the gurus help me
Diamond running 0.95 bePe and pc running xp sp3.
Kind regards, Heien.
Try to flash a stock ROM and check if you run into the same problem.
In order to sync, you must be running the handset normally, don't enter bootloader mode.
Did the system prompt you for drivers the first time you connected it to the PC? Activesync 4.5 provides the rndis drivers.
the problem is, i cant even flash my device, i tried to flash it, but i get a connection error with the tool.
I know about the bootloadermode, and that i am not able to sync in that state, but i just wanted my pc/diamond to recognize the connection between them. The system did not prompt me for drivers, it just went straigth to unrecognized device. i even tried to point the the driverupdate tool to the drivers folder with the rndis drivers in the as folder.
-i also tried to hardreset my device.
Try doing the same on a fresh stock XP install, without firewall or anything similar.
We need to figure out if it's a problem with the handset itself or your OS/PC.
Try another USB port (DON'T use hubs).
Enter bootloader mode. When you connect it to the USB, it should at least toggle from serial to usb.
If that's the case, at least your USb is working well.
I've reading some FAQs and Wiki articles before make this question.
Last weekend my Kaiser crashed into the floor (a very very very soft fall) and the battery jumped out the phone.
I put the battery, and in the first boot.... Ooops!! Tricolor screen showing:
"Hardspl 3.29
Serial "
There is a quick splash screen showing "No image file".
I've tried to boot several times, and i get into OS once, but the pda works so slow.
Solutions that i've tried:
a) MMTY prompt. Boot command doesn't work and i dont know the "boot command" for Hardspl 3.29. Anyway, i dont want to mess with MMTY and get a brick...
b) When i get into OS i tried to connect via Activesync (to reflash Hardspl) but...
After JumpSPL I get "Jump Tricolor Screen"
I unplug usb, uncheck "USB Connections", plug USB... but KaiserKustomRuu doesnt work! It closes after executing it. (The day that i flashed hardspl 3.29 i did it the same way, and everything went ok)
What can i do?
Please help!!!
(I dont care loosing data, i only want recover the pda)
EDIT:
Hi there.
Finally i did this:
- Re-flash HardSPL 3.29 (via MicroSD)
After that, OS always booted (WM 6.0 Official HTC)
However, Activesync does not work. When i plug the usb cable, the battery begins charging and activesync runs on PDA and Pc, but PC says that connection is not possible. I've tried with 2 or 3 computers with same results.
(Allow usb connections is marked)
Also, all the OS gets so so so slow when usb cable is plugged.
Then i did:
- Hard Reset to back default WM 6.0 official ROM
* No way. ActiveSync does not connect.
- Flashing a cooked Rom (WM 6.5 spanish) and a new radio (from 1.27.12.32 that i always used with WM6.0 to 1.70.19.09)
* No way. No i have Hardspl 3.29, WM 6.5 spanish cooked rom, and 1.70.19.09 radio. Everything seems to be ok...except for Activesync.
Please...help....
EDIT 2:
Ok.... i've tried to access MTTY prompt but it was impossible.
When i plug the USB cable i get an error in the computer (device not recognized), but PDA screen changes between "serial" and "usb".
After 20 or more tries i got into MTTY prompt, but that was the last time until now.
So... i think that mi usb port is broken ( is not the cable or the computer, i used some cables and computers)
I've tried to move the usb connectors with a pin, slowly, and i have cleaned evertything, but nothing happens.
What may i do?
How can i check my flash/nand to check errors? Of course, i need to check it but not using USB !
USB port is charging the battery, and windows attempts to install the device (Windows mobile device, as says) but the installation is not finished.
So you are unable to use activsync at all on your phone?
http://forum.xda-developers.com/showthread.php?t=423486
Hi there.
Yes, i am unable to use activesync from OS.
Draelee, i will check that thread, thanks.
Hi there.
Finally i did this:
- Re-flash HardSPL 3.29 (via MicroSD)
After that, OS always booted (WM 6.0 Official HTC)
However, Activesync does not work. When i plug the usb cable, the battery begins charging and activesync runs on PDA and Pc, but PC says that connection is not possible. I've tried with 2 or 3 computers with same results.
(Allow usb connections is marked)
Also, all the OS gets so so so slow when usb cable is plugged.
Then i did:
- Hard Reset to back default WM 6.0 official ROM
* No way. ActiveSync does not connect.
- Flashing a cooked Rom (WM 6.5 spanish) and a new radio (from 1.27.12.32 that i always used with WM6.0 to 1.70.19.09)
* No way. No i have Hardspl 3.29, WM 6.5 spanish cooked rom, and 1.70.19.09 radio. Everything seems to be ok...except for Activesync.
Please...help....
UPDATED the first post.
Is my PDA - USB port broken?
I hate to tell you this.. But a work around could be to Activesync via Bluetooth... Now a days you can get a USB Bluetooth dongle for $5 or sell... My stepsons USB port is so broke that he has 3 batteries and a stand alone battery charger.. he jsut swaps batteries when it dies... He syncs via bluetooth and has no problems....
So, once you have read the entire post...
Do you think in a software or an hardware problem?
Bluetooth sync is a good option, but i would like to investigate a little.
I've reflashed HardSPL, ROM and RADIO but i think that there are more bad data sectors.
How can i check my flash/nand to check errors? Of course, i need to check it but not using USB !
USB port is charging the battery, and windows attempts to install the device (Windows mobile device, as says) but the installation is not finished.
Thanks!!
Try flashing an Android ROM
Hi,
I had the same problem on my phone for about 6 months. I completely gave up on it. A few days ago I successfully flashed an Android ROM to NAND but ended up flashing back to WinMo. Surprisingly my USB activesync / headset adapter started working again!!
I'd give it a shot if I were you. Worked for me
~Joe~
Guys,
I've been trying to install HardSPL to get this Touch X 9.0 Rom..
But every time i try to install it ask's me if i've connected the phone properly to the USB etc..
What can I do T_T ?
The phone is fully syncronized with ActiveSync
you can try other usb slot or a new computer .
nat
xRaitei said:
Guys,
I've been trying to install HardSPL to get this Touch X 9.0 Rom..
But every time i try to install it ask's me if i've connected the phone properly to the USB etc..
What can I do T_T ?
The phone is fully syncronized with ActiveSync
Click to expand...
Click to collapse
1) To be ultimately sure, take out everything that is connected on all USB ports (and I mean, ALL) EXCEPT your Xperia. Also, uncheck the "Advanced Network Functionality" of ActiveSync.
2) If you have the same problem after following my advise, change to another USB port. Try every single port.
3) If you still get disconnections, try another computer (or laptop).
4) Problems still persist? then check your USB cable itself (or the USB ports) if it is faulty.
It was always working. But now when I connect it to the PC. Only battery charging, no usb device recognized (nothing will show in my computer). I have tried different PCs, all are the same.
And if I boot into Hardspl four color screen, usb can be found. So I flashed different Radios and Roms, even latest stock WM6.1 ROM. Still the USB only works in SPL but not Windows Mobile Interface.
I think it maybe a software problem. But since it is now with stock WM6.1 and Radio, what can I do further?
Thanks!
try to disable "Enable faster data synchronization" under the USB to PC settings and try again.
the USB to PC settings are usually in Start->Settings->Connections.
other than that, i can't think of much else but i'm certain someone else can come up with some more suggestions.
ASCIIker said:
try to disable "Enable faster data synchronization" under the USB to PC settings and try again.
the USB to PC settings are usually in Start->Settings->Connections.
other than that, i can't think of much else but i'm certain someone else can come up with some more suggestions.
Click to expand...
Click to collapse
Thanks! I have tried that already after searched over google and xda. But it doesn't work. No usb device show up when I connect the Kaiser. Only battery charging.
Does spl USB mode use different pins from Activesync? Forgot to say, I flashed Hardspl with force-usb.
Maybe like this, the USB port detects PC host before it activate USB function. In spl, the "force-usb" gets the USB port always activated.
changing the radio isnt going to make a blind bit of difference, although stating which rom you flashed and what windows version (PC) you are using might!
If its xp totally uninstall active sync and download the latest version from microsoft and install that
If its vista then download the latest version of WMDC and install that
also after flashing the rom, as soon as you have aligned the screen and customization has completed soft reset and when it reloads go and clear storage.
Did you have a biug storage rom installed before it failed to connect to USB?
Thats about all i can suggest till you supply more info
Thank you for those suggestion. I thought flash new roms will automatically hard reset the Kaiser. I will try to use "clear storage".
The rom I last used is http://forum.xda-developers.com/showthread.php?t=533617
Before I flashed this rom, usb worked fine.
The problem is no device shown in Windows device manager, not even unknown device. Just like nothing has been plug into the USB port. But same cable and port work with another X1
i'm having the same problem as well after flashing b16b rom
http://forum.xda-developers.com/showpost.php?p=3996365&postcount=826
anyone have the solution ? even i chg the spl and flash the stock rom my activesync still won't functioning..the usb port only able to charge the battery only
I would check your pins in the charging port and make sure you can see 5 pins on top and they are not bent