Database Develop

Diamond with non-bundled AS?

Hey All.
I am on vacation, and just brougth a new notebook (lovely Medion Akoya), and i want to sync with my diamond. However, i downloaded the active sync from the ms homepage, and i get the "Unrecognized device" error all the time.
Yes, i tried to use different cables, yes i tried to deactivate the advanced network, however, i doesnt seem to recognize it at all.
Even if i do a softreset + volume down, i just get the SPL1-40 screen, but eventhou my phone is plugged in the USB, it doesnt say that, only "serial" when i disconnect.
I've been searching this forum the entire day, and i cant seem to find a solution. So, i kindly ask the gurus help me
Diamond running 0.95 bePe and pc running xp sp3.
Kind regards, Heien.

Try to flash a stock ROM and check if you run into the same problem.
In order to sync, you must be running the handset normally, don't enter bootloader mode.
Did the system prompt you for drivers the first time you connected it to the PC? Activesync 4.5 provides the rndis drivers.

the problem is, i cant even flash my device, i tried to flash it, but i get a connection error with the tool.
I know about the bootloadermode, and that i am not able to sync in that state, but i just wanted my pc/diamond to recognize the connection between them. The system did not prompt me for drivers, it just went straigth to unrecognized device. i even tried to point the the driverupdate tool to the drivers folder with the rndis drivers in the as folder.
-i also tried to hardreset my device.

Try doing the same on a fresh stock XP install, without firewall or anything similar.
We need to figure out if it's a problem with the handset itself or your OS/PC.
Try another USB port (DON'T use hubs).
Enter bootloader mode. When you connect it to the USB, it should at least toggle from serial to usb.
If that's the case, at least your USb is working well.

Killed my Tytn 2 ?

Hi guys, i have probably killed my beloved kaiser.
This is what i did:
- Flashed latest Hyperdragon III Rom - all worked fine here
- Sometime later i figured out that the phone was not able to connect to my PC anymore (tried different computer and cable, no change: unknown usb device)
- I then entered boot loader and tried to flash an older rom (Garmin DK 3) but it stopped at 16% and i had to enter boot loader again.
The result:
Now no pc is detecting the tytn 2 correctly (unkown usb device) on boot loader screen. I guess that the usb port on the phone is somehow damaged. Any suggestions ?

http://wiki.xda-developers.com/index.php?pagename=Kaiser_Stuck_at_bootloader
there u go

I just want to say that your phone not connecting was a simple thing.

Moved to apropos section.

tabaz said:
- Sometime later i figured out that the phone was not able to connect to my PC anymore (tried different computer and cable, no change: unknown usb device)
Click to expand...
Click to collapse
Did you try deleting your sync settings?
Delete device from sync list.
unplug/replug usb. setup device again.
Or I have also had to un & re install Active-sync.
Hope this helps

nonono .. its not that active sync is not working anymore, its that windows detects the device either as unknown device (on bootloader screen!) or does not detect it at all. I even cant select USB in mtty.exe - active sync disabled. Iam pretty much sure its an usb port issue since my tytn2 have had always problem with usb cons (did not recharge and stuff). Before that issue my pc had detected the tytn2 in bootloader screen.

tabaz said:
nonono .. its not that active sync is not working anymore, its that windows detects the device either as unknown device (on bootloader screen!) or does not detect it at all. I even cant select USB in mtty.exe - active sync disabled. Iam pretty much sure its an usb port issue since my tytn2 have had always problem with usb cons (did not recharge and stuff). Before that issue my pc had detected the tytn2 in bootloader screen.
Click to expand...
Click to collapse
Try another USB cable. I have a faulty cable at work and my phone disconnects from AS all the time. At home, no problems
Dave

i have tried several usb cable on several computer - same problem.

tabaz said:
i have tried several usb cable on several computer - same problem.
Click to expand...
Click to collapse
Oh well, it worth a shot.
Dave

USB only works in SPL. No device found when in WM

It was always working. But now when I connect it to the PC. Only battery charging, no usb device recognized (nothing will show in my computer). I have tried different PCs, all are the same.
And if I boot into Hardspl four color screen, usb can be found. So I flashed different Radios and Roms, even latest stock WM6.1 ROM. Still the USB only works in SPL but not Windows Mobile Interface.
I think it maybe a software problem. But since it is now with stock WM6.1 and Radio, what can I do further?
Thanks!

try to disable "Enable faster data synchronization" under the USB to PC settings and try again.
the USB to PC settings are usually in Start->Settings->Connections.
other than that, i can't think of much else but i'm certain someone else can come up with some more suggestions.

ASCIIker said:
try to disable "Enable faster data synchronization" under the USB to PC settings and try again.
the USB to PC settings are usually in Start->Settings->Connections.
other than that, i can't think of much else but i'm certain someone else can come up with some more suggestions.
Click to expand...
Click to collapse
Thanks! I have tried that already after searched over google and xda. But it doesn't work. No usb device show up when I connect the Kaiser. Only battery charging.
Does spl USB mode use different pins from Activesync? Forgot to say, I flashed Hardspl with force-usb.
Maybe like this, the USB port detects PC host before it activate USB function. In spl, the "force-usb" gets the USB port always activated.

changing the radio isnt going to make a blind bit of difference, although stating which rom you flashed and what windows version (PC) you are using might!
If its xp totally uninstall active sync and download the latest version from microsoft and install that
If its vista then download the latest version of WMDC and install that
also after flashing the rom, as soon as you have aligned the screen and customization has completed soft reset and when it reloads go and clear storage.
Did you have a biug storage rom installed before it failed to connect to USB?
Thats about all i can suggest till you supply more info

Thank you for those suggestion. I thought flash new roms will automatically hard reset the Kaiser. I will try to use "clear storage".
The rom I last used is http://forum.xda-developers.com/showthread.php?t=533617
Before I flashed this rom, usb worked fine.
The problem is no device shown in Windows device manager, not even unknown device. Just like nothing has been plug into the USB port. But same cable and port work with another X1

i'm having the same problem as well after flashing b16b rom
http://forum.xda-developers.com/showpost.php?p=3996365&postcount=826
anyone have the solution ? even i chg the spl and flash the stock rom my activesync still won't functioning..the usb port only able to charge the battery only

I would check your pins in the charging port and make sure you can see 5 pins on top and they are not bent

What to do when computer doesn't recognize phone plugged?

I have a problem with the diamond and needs to change ROM/SPL and other stuff, but it won't recognize that the phone has been plugged in. I have tried 5 different USB cables and 3 different computers. I don't have HTC warranty. I've done 5+ hard-resets.
Please help.

First, what OSes? For instance: win 7 doesn't recognize the phone if it tries to connect in active sync mode.

I've always used windows xp, in the past it worked.

hi,
try to connect your htc twice : my computer does not recognize my htc at first plug but when I retry in less than 1 minute, my htc displays popup menu and I can choose USB/active sync, I click done and then my computer recognizes it. I don't know if it will work with your device but you can try that ^^

Thanks for the suggestion,
I've already tried that a lot of times, nothing doing.

ok, did you try to change the status of your usb connexion ?
I mean : settings>connections>usbtoPC> then try these 4 combinations together :
- enable faster data synchronization (try both modes on/off)
- ask me about usb connection type (try both modes on/off)

I can get into bootloader, but never know that you could flash ROM in there. Is there a guide?
Also, I have a problem with a flickering screen that some threads here suggest changing SPL version to fix. Is it possible to change SPL using bootloader?

I just downoaded WM6.5 to my phone and did a ROM flash from internal storage, but USB still has problem & flickering screen still there. I need to be able to change the HardSPL w/o connection to the computer.
Is it possible to load some of the .exe in the HardSPL package and run it on the phone?
Someone help,
Thanks

Perhaps it's simply due to your PC firewall ?? Deactivate it and try to plug your htc again...

the problem is that my the computer doesn't connect with the phone via the USB cable.

just try to disable your PC firewall before connecting your device.

sorry I cannot find CustomRUU.exe on this forum, i did find DiamondCustomRUU.exe on the wiki. However, the interface for it is the same as the RomUpdateUtility.exe, which requires activesync connection.
I did proceed anyways by entering bootloader(Voldown + softreset) and run the utility -> nothing works. Then I try the USB trigger mode (Voldown + back + softreset) and run the utility -> nothing works.
I am tempted to put the HardSPL in the internal storage and rename it DIAMING.NBH and flash it but I do not know the consequences.
Thank you for your replies,
I'd appreciate more help

[Q] HTC Touch Viva - No USB connection help

Sorry I did not search cuz my internet connection is limited so i don't know if anyone has posted the issue here apologyze!
I have an HTC Touch Viva
ROM: 1.26.707.2 WWE
Radio: 03.29.90
Protocol: 4.1.13.66
This one has never been flashed a custom rom, ive tried to flash a rom but i can't bcuz it is not recognized on the pc, I DOES NOTHING! Is there a way to flash a hard spl or custom rom without usb connection? Thanks in advance.
junior0186 said:
This one has never been flashed a custom rom, ive tried to flash a rom but i can't bcuz it is not recognized on the pc, I DOES NOTHING! Is there a way to flash a hard spl or custom rom without usb connection? Thanks in advance.
Click to expand...
Click to collapse
is this device succesfully sync with the computer using ActiveSync (with a cable).
i can recommened following:
> Check Activesync working properly
> If not, check drivers are installed
> in the phone, Connections > Disable 'Enable Fast Data Connection' under ActiveSync options, sometimes, it works
> Check data cable, try with another cable, try another computer maybe
> Try reset, switch on the phone, while connected to the computer.

format ur memory SD with FAT32
change RUU-Sighend.nbh to OPALIMG.nbh and place it in the root of memory SD
go to bootloder then the rom flashs.then restart with pressing Stylus
not: u must had HSPL before
do at ur own risk (but i tasted)

I' m screw my HTC usb port, therefore, I'm using Blootooth, es veeeery slowwww, but i can sincronice
Nevertheless, blutooth is muche mor complicated

yayo_foro said:
I' m screw my HTC usb port, therefore, I'm using Blootooth, es veeeery slowwww, but i can sincronice
Nevertheless, blutooth is muche mor complicated
Click to expand...
Click to collapse
try to use a memorysd reader