Database Develop

MDA Unlock Blues

Greetings.
I have spent the past couple days searching for a solution to unlock an MDA. I have got all of the different versions of lokiwiz, wizardunlock, lokiwizMsl, etc. and the mda refuses to be unlocked. I believe I am following the directions step for step, but even the forums where people have the same problems as I (internal read/write error, can't find specified path, etc.), none of the solutions are working for this device. From my searching I believe it is a g3 MDA. The stats for the device are as follows:
IPL 2.26
SPL 2.26
GSM 02.25.11
OS 2.26.10.2
I have tried downgrading the firmware to no avail (the ftp site doesnt have the file), and the phone doesn't want to be DOWNgraded anyway. If ANYONE out there is cyberspace can assist, my gratitude will be pouring forth from their screen!
[email protected]

So have you followed this thread? It has valid links to get the Button ROM so you can do the downgrade and points you to the threads that will help you do this unlock:
http://forum.xda-developers.com/showthread.php?t=298613
In a nutshell, downgrade to the button rom (just execute the file and follow the directions). Your IPL will be 1.xx at this point and then you can use lokiwiz .2b to do the CID unlock. all of this is outlined in the excellent guide by Dr. P (which the above link will take you to). Then get your SPL down to 1.xx, then upgrade back up to 2.xx. Then you can start flashing custom roms.
If you still have issues, let us know exactly what you are doing and exactly what errors you see (or what your phone does or doesn't do).

Greetings mfrazzz.
I have indeed downloaded and attempted the button ROM. The installer started and then after about two minutes told me that the phone wouldn't let me Downgrade the ROM. I am currently downloading (70% done) the button ROM again and will see if it has the same problem. If so, I will of course seek the help of the experts here. Thanks for the quick reply!

gtw said:
I have indeed downloaded and attempted the button ROM. The installer started and then after about two minutes told me that the phone wouldn't let me Downgrade the ROM.
Click to expand...
Click to collapse
Let us know the exact error you get (I assume the error is on the PC side) and then what the behavior of the phone is after you do this. Also, at what point does this error happen (has it actually started loading the rom or is it before it gets to that point and where its just checking your phone?)
Another option would be to try putting on the Wizard Love rom and then downgrading to button. Shot in the dark but worth a try.
Also remove your SD card when you try to downgrade. Try from a different PC if you can, or reboot your current pc before attempting this again.
Good luck!

Greetings again.
After downloading and executing the button ROM updater, it went to the status bar screen and stayed there for about a minute before displaying the following error message:
Error [296] : UPGRADE ONLY
This is (I believe) the same error I got previously. I was using RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship (which is the file that I downloaded from http://forum.xda-developers.com/showthread.php?t=298613 under the link button ROM (step g3.3).
ALSO... the phone is stuck in the multicolored ROM screen. (the red green and blue) On the screen (from top to bottom
IPL 2.26 RUU
SPL 2.26
USB

gtw said:
This is (I believe) the same error I got previously. I was using RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship (which is the file that I downloaded from http://forum.xda-developers.com/showthread.php?t=298613 under the link button ROM (step g3.3).
Click to expand...
Click to collapse
Nope, thats the Cingular 2.25 ROM. Thats why you are getting the error (since you aren't CID Unlocked it won't let you load that).
The ROM you are supposed to be loading is this one:
http://rapidshare.com/files/18212239/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe.html
Thats the Button ROM (and the one I show being in that link on that page). Please download that, and run it. You should make more progress
Since you are on the bootloader screen (Rainbow screen you described) just run the button rom when you get it downloaded (active sync will not connect, but since you see USB above the left soft key you have the connection to do this).

I see....it would make a difference if I got the right program! Rapidshare says I have ten minutes before I can download another file, so after I download http://rapidshare.com/files/18212239...WWE.exe.h tml, I will try it and post the results here! Thank you so much for your help, mfrazzz!

Greetings.
After downloading and installing (onto the phone) http://rapidshare.com/files/18212239...WWE.exe.h tml, the stats for the phone are
ROM: 2.26.10.2 WWE
Radio Version: 02.25.11
Protocol: 4.1.13.12
ExtRom: 2.26.10.105
After executing lokiwiz, lokiwizMSL, wizardunlock, and a few different versions of each (after I put the enableRapi onto the phone), the phone still won't unlock. It either gives me a "Cannot find the specified path" error, or the "Internal read/write error".
Im not sure that the file I downloaded was a 'down'grade, so if anyone sees a solution, please post!
Thank you

Did the flash of the Button ROM work? Your IPL should have changed to 1.xx after doing that flash (and your splash screen would be a photo with a mug of beer in the foreground). Since your IPL and SPL still show 2.26, it appears the flashing of the button rom didn't happen.
Not sure what else to tell you. It should be as simple as running the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe file, and letting it flash to your phone to do the initial downgrade. But you have to be a 1.xx for IPL before the lokiwiz .2b will be able to work (so there is no point in doing anything else until the steps before that complete. Again, follow to the letter (including checking the results) the thread by Dr. P on CID Unlocking. You should never try to do steps before the previous step is complete).

mfrazzz said:
It should be as simple as running the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe file, and letting it flash to your phone to do the initial downgrade.
Click to expand...
Click to collapse
I thought it would be that easy too. I clicked on the file, it went through the flash, and those are the stats that showed up. I am currently trying the flash again. One difference I noticed this time is that the version it says is going to be installed is 1.xx this time, last time it said 2.XX. It looks like its going ok, though. Ill post again once it is done.

Greetings.
THANKS FOR YOUR HELP MFRAZZZ! Not only did your prompt responses brighten my otherwise gloomy, MDA filled day! Your patience with my noobitude on this device (its not mine) has been a blessing beyond anything I could have hoped for. The device is now UNLOCKED!!! After the last flash, the beer mug showed up and all was well. Lokiwiz worked like a charm and your help, as I said, was much needed! THANK YOU!

gtw said:
Greetings.
THANKS FOR YOUR HELP MFRAZZZ! Not only did your prompt responses brighten my otherwise gloomy, MDA filled day! Your patience with my noobitude on this device (its not mine) has been a blessing beyond anything I could have hoped for. The device is now UNLOCKED!!! After the last flash, the beer mug showed up and all was well. Lokiwiz worked like a charm and your help, as I said, was much needed! THANK YOU!
Click to expand...
Click to collapse
Very cool. Just make sure you get the SPL down to 1.xx before you move back up to a 2.xx Official rom and you will be golden.
Congrats, and glad I could help

mfrazzz you are amazing

Did I kill the Wizard? :-(

[SOLVED! See page 4]
I have a Cingular 8125, which I hadn't used for a while (got a Trinity
I am trying to set it up for my wife, so I attempted to unlock it and upgrade to WM6. It is a G3 (it had 2.26). I had upgraded it several times before. but was never able to bring it down to 1.xx in order to unlock it.
So, I started trying to downgrade it, but basically, every time it entered bootloader, it seemed to lose connection and it just timed out on the PC, without ever going to the update bar on the bootloader screen.
I ran IPL_SPL_3.08, and it upgraded fine. But still no go on downgrading.
Finally, I ran Shelltool (bug fixed) and managed to flash to OS 1.5.4.2. But, after the hard reset, it just stays on the blue Cingular screen (showing IPL 3.08; SPL 3.08; GSM 02.47.11; OS 1.5.4.2.)
I have tried flashing again with an original Cingular WWE ROM (RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe), with the 1.5.4.2 ROM, even with a WM6 ROM (again, through Shelltool.) I have placed it in a powered cradle, have tried both Shelltool and RUU flashes, both while in the blue Cingular screen, and while in Bootloader mode. I have disconnected and reconnected each time, and rebooted many times (both the Wizard and the PC.) I have hard-reset. I have also tried both with USB selected and unselected in Activesync.
The Shelltool seems to freeze. The official RUU gives "ERROR [296]: UPGRADE ONLY. The NBF file cannot be used for your PDA Phone. Please get another NBF file." Or, alternately, it gives "ERROR [264]: CONNECTION."
Any ideas if this is repairable?
(Or should I cry (or take a hammer to the Wizard:-((

Mine is a 2.25 and it's a G4.. Isnt 2.26 a G4?

I think it was 2.26 (it may have been something like 2.27....), but it definitely didn't have the .000 at the end. I thought that the Wizards without the .000 were G3. Did I screw up?

Madcap180 said:
Mine is a 2.25 and it's a G4.. Isnt 2.26 a G4?
Click to expand...
Click to collapse
2.25.0001 or 2.26.0001 would be a G4
2.25 or 2.26 would be a G3

MacGuy2006 said:
I have a Cingular 8125, which I hadn't used for a while (got a Trinity
I am trying to set it up for my wife, so I attempted to unlock it and upgrade to WM6. It is a G3 (it had 2.26). I had upgraded it several times before. but was never able to bring it down to 1.xx in order to unlock it.
So, I started trying to downgrade it, but basically, every time it entered bootloader, it seemed to lose connection and it just timed out on the PC, without ever going to the update bar on the bootloader screen.
I ran IPL_SPL_3.08, and it upgraded fine. But still no go on downgrading.
Finally, I ran Shelltool (bug fixed) and managed to flash to OS 1.5.4.2. But, after the hard reset, it just stays on the blue Cingular screen (showing IPL 3.08; SPL 3.08; GSM 02.47.11; OS 1.5.4.2.)
I have tried flashing again with an original Cingular WWE ROM (RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe), with the 1.5.4.2 ROM, even with a WM6 ROM (again, through Shelltool.) I have placed it in a powered cradle, have tried both Shelltool and RUU flashes, both while in the blue Cingular screen, and while in Bootloader mode. I have disconnected and reconnected each time, and rebooted many times (both the Wizard and the PC.) I have hard-reset. I have also tried both with USB selected and unselected in Activesync.
The Shelltool seems to freeze. The official RUU gives "ERROR [296]: UPGRADE ONLY. The NBF file cannot be used for your PDA Phone. Please get another NBF file." Or, alternately, it gives "ERROR [264]: CONNECTION."
Any ideas if this is repairable?
(Or should I cry (or take a hammer to the Wizard:-((
Click to expand...
Click to collapse
I thought I read somewhere that IPL/SPL 3.08 was a bad convert from a Charmer? If this is true and the Charmer bootloaders are different than the Wizard bootloaders then you may have put yourself in a bind.
The fact that you can still get past bootloader is promising even though the phone doesn't finish booting.
Try flashing from the bootloader (tricolor IPL/SPL screen with USB in the corner)

Thanks. I've been trying to flash in both bootloader or "blue" screen, but no go so far. I just tried the official Cingular .nbf through shelltool: it spent about 30 minutes (in bootloader,) then it stopped responding. It's been doing this forever now.
Any other options left?

MacGuy2006 said:
Thanks. I've been trying to flash in both bootloader or "blue" screen, but no go so far. I just tried the official Cingular .nbf through shelltool: it spent about 30 minutes (in bootloader,) then it stopped responding. It's been doing this forever now.
Any other options left?
Click to expand...
Click to collapse
You CAN'T use shelltool in boot loader mode! it needs the OS and the TRUFFS to read and write to the phone.
Any phone that doesn't go past the boot loader must be fixed with mtty, RUU or SD card...

Thanks for the info. I've been reading about mmty and just downloaded it. But I only have a 4GB card handy (from my Trinity.) I might be able to find my old 2GB one at home.
Edit: Well, this is what I just found: http://forum.xda-developers.com/showthread.php?t=308772&highlight=mtty+wizard
It seems that the IPL_SPL 3.08 might be a real problem. I'll try the card flash, but based on the above thread, I am not holding my breath.
If anyone has a suggestion or a solution, please let me know.
Thanks!

BTW, if the problem is indeed with the IPL_SPL 3.08, then perhaps the suggestion that we upgrade to it (in red) here http://forum.xda-developers.com/showthread.php?t=285435 should be removed, so that we don't get more expensive bricks.

Just to clear up the question about 3.08 IPL/SPL, it isn't an issue at all. It's been tested thoroughly to work well, better than 2.26.

TaurusBullba said:
Just to clear up the question about 3.08 IPL/SPL, it isn't an issue at all. It's been tested thoroughly to work well, better than 2.26.
Click to expand...
Click to collapse
After I unlocked my wizard and before I try any new ROM, I always burn the latest German wizard ROM with 3.08 IPL/SPL "ruu_vario_aku3.3_3822_382120_026911_tmo_de_ger_ship". Then I downgrade the Radio ROM to Cingular 2.25.11. Then I burn my ROM of choice. I've found it works best for me. I've never had a problem with 3.08.

TaurusBullba said:
Just to clear up the question about 3.08 IPL/SPL, it isn't an issue at all. It's been tested thoroughly to work well, better than 2.26.
Click to expand...
Click to collapse
What are the grounds for such a comparison? How to tell that an SPL works better than another? As far as i know the SPL is there to initialise the hardware and to apply security restrictions.
What i'd like to know is if anyone has been successful in downgrading IPL/SPL from 3.xx to 2.xx as itsme once said that there was a security in newer SPL's preventing downgrading (i must look for it...)
cheers

O.K., so maybe it's not 3.08, but something has sure gone bad.
I am trying to use mtty 1.1.42.538, but see only Port 1, Port 2 and USB. When I type in \\.\WSCUSBSH001 I get a message that it cannot open the \\.\WSCUSBSH001 port.
I tried resetting as described in message #7 here http://forum.xda-developers.com/showthread.php?t=264652&highlight=mtty1.42, but nothing happened.
I also tried choosing USB, then typed in r2sd all and again, nothing happened - I just get CMD> again....
So, can anyone think of anything else I can do, or should I just drop it from the 4th floor?

What IPL/SPL values you have at this moment?

mestrini said:
What IPL/SPL values you have at this moment?
Click to expand...
Click to collapse
Both ar 3.08, and I have the feeling that this is why I cannot flash the official Cingular ROM over what I have now. Which makes me wonder: is there an official Wizard ROM file combined with the IPL/SPL 3.08? This may at leas allow me to flash.

MacGuy2006 said:
Both ar 3.08, and I have the feeling that this is why I cannot flash the official Cingular ROM over what I have now. Which makes me wonder: is there an official Wizard ROM file combined with the IPL/SPL 3.08? This may at leas allow me to flash.
Click to expand...
Click to collapse
I had also upgraded my IPL/SPL to 3.08 -- up from the 2.25 on the newest Cingular ROM.
Anytime I've flashed to a WM6 ROM, I've been able to downgrade to the T-Mobile 2.26 ROM -- which changes the IPL/SPL to 2.26 -- with no problems before upgrading to a WM6 ROM. After flashing the WM6, I then go back in and upgrade the IPL/SPL once again to 3.08. It's not failed me yet.

O.K., I've spent the weekend screwing around with this:
If I run any of the original 2.xx ROMs, I get "you need an updated utility" message and then the utility goes to the "Exit" screen. (I am assuming this is because of the 3.08 IPL/SPL.)
mtty tells me I don't have permissions when I tried to load the ROM on a SD card (remember, the 8125 is not SuperCD-ed.). It also does nothing when I type "set 14 0" or "task 28."
But, I found that I can run the XDA Mobile 6 ROM (http://forum.xda-developers.com/showthread.php?t=310954) and it actually starts updating, but when it gets to 99%, the bar on the 8125 turns red and after a while the Update Utility tells me that the Wizard is not connected anymore.
Got very excited when I tried mattk_r's InGeNeTiCs' ROM(http://forum.xda-developers.com/showthread.php?t=311144): it started updating, went all the way to 100%, at which point the bar on the 8125 did turn red, however after a period of time the utility gave me the "Congratulations" message and told me I've successfully upgraded. But then, the 8125 reboots, and unfortunately, it still hangs on the boot screen, and it still gives the OS as 1.5.4.2. Have tried a number of times, always the same:-(
Oh, I tried upgrading the Radio only, and it worked: I was able to upgrade to 02.61.11.
So, does it seem like there is hope, and can anyone think of what else I can do?

MacGuy2006 said:
O.K., I've spent the weekend screwing around with this:
If I run any of the original 2.xx ROMs, I get "you need an updated utility" message and then the utility goes to the "Exit" screen. (I am assuming this is because of the 3.08 IPL/SPL.)
mtty tells me I don't have permissions when I tried to load the ROM on a SD card (remember, the 8125 is not SuperCD-ed.). It also does nothing when I type "set 14 0" or "task 28."
But, I found that I can run the XDA Mobile 6 ROM (http://forum.xda-developers.com/showthread.php?t=310954) and it actually starts updating, but when it gets to 99%, the bar on the 8125 turns red and after a while the Update Utility tells me that the Wizard is not connected anymore.
Got very excited when I tried mattk_r's InGeNeTiCs' ROM(http://forum.xda-developers.com/showthread.php?t=311144): it started updating, went all the way to 100%, at which point the bar on the 8125 did turn red, however after a period of time the utility gave me the "Congratulations" message and told me I've successfully upgraded. But then, the 8125 reboots, and unfortunately, it still hangs on the boot screen, and it still gives the OS as 1.5.4.2. Have tried a number of times, always the same:-(
Oh, I tried upgrading the Radio only, and it worked: I was able to upgrade to 02.61.11.
So, does it seem like there is hope, and can anyone think of what else I can do?
Click to expand...
Click to collapse
If I were you I might be talking to IMEI unlockers. Their process works from bootloader and might be able to get you CID unlocked and fix your corrupted CID area, which seems to be your major problem atm. In any case I would contact them and explain your situation and see if they think their software will unlock your phone. If so then you should be good to go once you CID is "uncorrupted" and unlocked.

one question: can You HARD RESET your device?
Do you have "format failed" message?
if so, you have 50/50 per cent for resurrection.
3.08 is not direct problem here anyway..., version is not exactly matter of problem...
(imei? now? lol)...

Thanks!
Yes, I can hard-reset fine and it claims to reformat fine.
Tx for the suggestion - I will contact IMEI (they unlocked my Trinity before the free unlockers were available

ROM flash gone wronge! help!

I was upgrading my t-mobile 8150(?) the k-jam with the new windows mobile 6 and in the middle of it my comp crashed!! now i am stuck at the bootloader mode (3 colored screen) and when i try to redo it i get to 99% and get a 302 error message. i follow the instructions given but keeps going in circles. its a G3 so is my phone bricked or is there a way to save it? i've been looking at this site all day but am now just more confused. lol thanks for your help!

No your phone isn't bricked. As long as you can get into the bootloader screen you should be ok. What you need to do is flash an official carrier rom either tmobile 2.26 or wizard love rom after you that than you can reflash to wm6. look at the stickies in the wizard forums that is where you can find these roms.

Thanks for the info but seems my techno curse continues. I tried the wizard love rom but it was in a different language and whem i tried the tmobile 2.26 i got "error 274 connection." Any more suggestions? Again thanks soo much for an issue I'm sure has been posted here a thouand times.

This happens to me all the time. I always use the Cingular 2.25 rom, it works perfectly and I have an I-mate K-JAM. Then, do the WM6 upgrade, but ensure all of your Norton and Antivirus and background running apps are shut down. Good luck.

yes also take out your mini sd card if you have one. even though its in another language it will work. "AVANTI means next. so just keep hitting that and you will be fine.

hmm been trying to d/l the Cingular 2.25 rom but the link seems to have stoped working...

It;s aaaaaaaaaaaaaaalllllllllliiiiiiiiiiivvvvvvvvvvvvvvvvveeeeeeeeeeeeeeeee!!! for now lol Lets see what happens after i install wm6 I couldn't get the cingular rom but i had already dowbloaded the button rom i found here earlier and it worked like a dream!! quick and easy!! thank you all soooooo much!

hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?

flash to the tmo 2.26 or cingular 2.25...that will give you an IPL/SPL of 2.xx
then, you can flash to WM6

i want to delete this message. can't find a way to do it.

there's any other way to flash without usb cable?? sorry to bug in this thread but i lost my usb connection somehow and did a hard reset and still doesn't work. my phone charges. and no is not my computer cuz my wifes phone same as mine does sync i have a tmobile mda also known as the cingular 8125.

fallon75 said:
hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?
Click to expand...
Click to collapse
keep reflashing buttons rom until both ipl/spl are the same number. if they are different, then the flash didn't complete correctly. (it happens often, so it's kinda normal). just keep reflashing. after both ipl/spl are the same, then CID unlock and then update to an official carrier...then flash a wm6.

can anyone help me??

Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.

starkwong said:
Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.
Click to expand...
Click to collapse
it does shows but how can i flash?? it still won't connect o my pc. my pc doesn't recognize it. but it does recognize my wifes phone.

Try to run RUU straight with Wizard connected and running in bootloader mode

IPL locked on 1.01

Hello all,
I am somewhat of a newby here, but I have successfully unlocked my Cingular 8125 and installed a couple of WM6 ROMs. I followed the procedure of downgrading to Button 1.05 ROM, then running Lociwiz, then installing T-Mobile 2.26, then WM6 ROM. Worked great...until now.
I was going to try another ROM, and I followed above procedures (didn't know if I needed to after initial unlocking, but I did anyway). At the "install T-Mobile 2.26" step, after 1 %, I got an error 326?, nb file not for this device. I can still install cooked WM6 ROMs, and the SPL changes, but IPL always remains at 1.01. If I try to install IPL/SPL 3.08 CAB, SPL changes to 3.08, IPL stays at 1.01. I have re-installed Button Rom 1.05 and run Lociwiz a dozen times to no effect. Even the Cingular WM5 OS meant for this device gives me the same error code as the T-Mobile.
I'm hoping this is a simple newby error. Anybody have any suggestions.
Thanks for any help.
By the way, after loading Button ROM, my Wizard hangs during the customization routine at Signed_DiscoButton8.sa. I must soft reset.

I got exactly the same problem.
I am now on IPL 1.01 , SPL 3.08, radio 2.69, using rom NBD 8.3
doesnt seem a problem however...

d-lite said:
I got exactly the same problem.
I am now on IPL 1.01 , SPL 3.08, radio 2.69, using rom NBD 8.3
doesnt seem a problem however...
Click to expand...
Click to collapse
Hey m8,
have you forgotten this thread (http://forum.xda-developers.com/showthread.php?t=319582) ? (see last post)
mestrini said:
hahaha nice to see good spirit after all this
Here goes:
Make backup of the CID block (VERY VERY important!!!)
Make backup of the GSM calibration block (VERY VERY important!!!)
Kill wcescomm.exe process
Start mtty, enter bootloader mode in Wizard and connect
type doctest (this will write test patterns in DOC chip and clear all data!)
Flash button ROM (1.01_IPL/1.01_SPL/1.05_OS)
Flash CID block backup (don't miss this)
Flash GSM calibration backup (important)
If all ok then remember to upgrade to 2.xx before installing WM6!!
Post results
EDIT:
Use WST for steps 1, 7 & 8
Click to expand...
Click to collapse
are you willing to prove me wrong?

mestrini said:
are you willing to prove me wrong?
Click to expand...
Click to collapse
yes.. missed your last post to be honest, sorry..
(btw phone is happy till now .. but we go for solving it, killing seems impossible)
step 2, gsm callibration block.. how do i copy?
D-Lite

use the "Read ROM" button and select the appropriate section from the list.

status:
Code:
DOC ImgFS partition read/write test PASS
Ext ROM partition read/write test, offset=0x0, length=0xA00000
Test pattern =0xAA
Flash Ext ROM failed.
DOC Ext ROM partition read/write test FAILED
--Flashing button rom @ 100%
--DATA CRASHES PLEASE CONTACT SERVICE CENTRE
--WST Says I am still on SPL 3.08 and rom is write protected.. screen of wizard says SPL 1.01 ...
--Installing Button ROM, ... SIM Lock SUDDENLY
--Screen goes funny flashing between simlock and customise
--Few soft-resets, WST now convinced on SPL 1.01 and flashed CID block
--Soft-reset
--Imei gone, flashed back GSM callib. data, softreset
--doesnt boot passed the pint of beer... going for RUU of T-Mobile 2.x
--bootloader, flashing RUU_Prodigy_2210205_22102108_021911_TMO_NL_DUT_Ship.exe
--The NBF can not be used for your phone @95%, followed by congratiolations (stupid software)
--trying UK version...
--all give error 326
--another button flash
--*PLING IDEA* on 3.08 i couldnt doctest properly... so doing it again
-- bad idea.. same result...

damn... i thought it would work
anyway, there was point where the phone had same values for IPL/SPL (not too bad ). What is strange is why phone didn't boot anymore after flashing the GSM calibration and saying the flashes weren't suited for the phone.
What state is it on now? Wanna go again? This time, instead of flashing the 'GSM calibration data' do a simple IMEI writing and try to unlock CID before upgrading to official ROMs
sorry for this...

IPL locked on 2.26
I am having the same issue. I have tried numberous times to load my original rom and get the 326 error @ 1%. My ipl remains locked on 2.26. Is there any way to fix this? Please help.

it is now on 1.01, got my own imei back, spl 3.08, nbd 8.x rom...
everything fine again.. pretty sure it has something to do with ext.rom and/or write protection of it.. will give it another shot but not this month.. getting busy
@acmickey, not sure if you got same issue... is your IPL 1.01? else you might just have a locked phone..

Hey d-lite,
I followed your example and loaded BSD8.3 ROM and IPL/SPL 3.08 and radio 2.69. Everything seems to be fine. No missed calls. All programs work (touchflo is pretty cool). IPL is still locked on 1.01, even though SPL is 3.08.
I tend to agree with you that something is suspicious concerning the extended ROM. The first symptom I had that something was wrong was after loading Button's ROM, during the customization routine, Signed_DiscoButton8 would not install. Phone locked up and had to soft reset.
Oh, well, at least the phone works. The downside, of course, is that you can't load an original ROM, even though you can load a cooked one. Weird, huh?
Hopefully someone a lot more knowledgeable than I will figure this one out soon. Will keep checking the boards. At least we don't have bricks.

I am having the exact same problem as the 1st post but my ipl is stuck on 2.26. I am using an unlocked device and I have no problem downgrading/upgrading the spl. I also get the 326 error when I try to flash back to the original rom. (I used to be able to do this without a problem - I can't figure out what happened.)
It's really weird and I have search and searched and can't seem to figure out a solution.

which SPL you have now?

sorry.... my spl is 1.01

Right. Assuming your device is working 'normally' are you willing to try something new? If so contact me PM

what have you cooked up this time mestrini? lol
my wiz (at 1.01 still..) is doing a-ok, but always willing to go for something new so we can fix this for the communities sake...

d-lite said:
what have you cooked up this time mestrini? lol
my wiz (at 1.01 still..) is doing a-ok, but always willing to go for something new so we can fix this for the communities sake...
Click to expand...
Click to collapse
sorry to mislead you buddy but acmickey got it all wrong and, instead of IPL stuck at 2.26 and SPL 1.01, he has same as you IPL 'locked' at 1.01
So my theory could not be verified.
cheers

Wizard stuck on three-colour screen IPL/SPL after attempt to unlock

I have a wizard (wiza110) running wm5 and i wanted to upgrade it. It was the first time i was trying such thing. I was following these instructions http://wiki.xda-developers.com/index.php?pagename=Wizard%20Windows%20Mobile%206%20for%20newbies. My device is g3. My first attempt was with Button Rom, everything was fine until 99%... i think it was error 302 or something. I took off the battery and plugged it again several times but nothing came out. I had the three-colour screen.
Then I tried The Xda_MiniS_LaunchROM_v154102.exe, still nothing, lokiwiz also...
Last attempt was with wizard Love. USB appears but the ruu can't see the device and stops the process
Any ideas?

i think the device was sim-unlocked...

Flash back to the original rom, charge the battery to 100%. Make a guest connection to windows and start reading this thread from the beginning

do you have a link for the original rom? the thing is that ipl is 1.05 and spl is 2.25

aposperitis said:
do you have a link for the original rom? the thing is that ipl is 1.05 and spl is 2.25
Click to expand...
Click to collapse
Based on my experience and what I've read here, I'm guessing that your original rom had ipl and spl both 2.25. When you installed the button rom, it updated the ipl but nothing else. Just a guess, but that's what happened to me the first time on my G3. I just re-flashed button rom and continued from there. You should try to find the original rom for whatever kind of phone you have (I mean, the rom from the service provider like Orange, AT&T, etc). Their latest rom might not be 2.25. For example, my phone originally came from T-Mobile. I have the T-Mobile rom that is I think 2.26. I keep it handy, but have only reflashed back to that rom once when my extended rom got messed up.
Read the link suggested above. Good stuff. It is possible to flash a phone that is stuck on the tri-color screen, but it might not work the first try.

Same thing here, just youre getting further
I have ipl and spl on 2.26 received it this way. It's G3. I've been a week looking through the forums. Trying to avoid posting here. But damn it. I can't seem to get anything right. I previously had the G1 and Juno, Flashing was a breeze. But here i feel lost.
Basically my problem is i can't get it to downgrade. upgrade. CID unlock, With neither Lokiwiz or WST. A pain. And really NO RUU runs past the 0% it reboots my phone to boot loader image and USB shows but it reads that it can't find my phone anymore. It's been charged to 100%. Deleted TEMP folder. Was guest under activesync. Changed my USB cables 10 times. It's frustrating. Please. Any suggestions??