Related
Is there a way to format the PDA and reinstall a ROM. My PH20B1 is started to freeze after a ROM is installed and at Complete on the Setup for minutes. I end up just soft-resting cause after mins past its not doing anything....Is there a way to fix that???
Isn't it supposed to be like that? You're supposed to reset after the ROM upgrade shows 100% complete.
I think I understand the problem you have from the limited information supplied.
You have rebooted to a white screen after a failed rom upgrade, correct?
If so, just disconnect your device from the PC, hold power+record buttons, then prod the reset hole with your stylus. You will see "Serial v2.xx" where "xx" can vary. Now attach the phone to your PC (device now shows "USB" instead of "serial").
Next, kill off all activesync processes on the PC (ctrl-alt-del to enter task manager, then end task on "rapimgr.exe", "wcescomm.exe", "wcesmgr.exe").
Now that the device is attached and activesync is killed, start the ROM upgrader application to update the phone ROM.
After successful upgrade, it often helps to reboot the PC as well as the phone, as activesync does not always recover well from having its processes killed.
Im saying that My PDA is starting to freeze. Even after running, its starting to freeze up and I have to soft reset it. I am able to install a ROM on it however at the end of installing the ROM where the screens says COMPLETE...Tap to continue ro begin using your device...and its starts the ROM....As soon as I tap the screen in the middle of starting WM5 it freezes... Ive even downgrade to Wm2oo3SE and it still freezes. But after soft resest there was a message about "system data is corrupted, System will erase all data to fix this error! Yes or No to fix"....Can that be fix or am I able to re-format the PDA hdd and reinstall WM2oo3SE or WM5?
Hi again,
This is a guess, so treat it as such, but I suspect that something in your extended ROM could be causing the problem. On first boot after reflash, a file "autorun.exe" is executed from the extended ROM, and this will normally install a bunch of CAB files.
If something in your extended ROM was corrupt or otherwise not correct, it could cause a lockup on first boot - immediately after calibrating the screen, setting the timezone etc, just as you describe.
The safest thing to do is to revert to the device's complete set of original ROMs, as found in this table :-
http://wiki.xda-developers.com/index.php?pagename=BA_Upgrades
The original ROM-set will restore the main ROM, extended ROM and radio ROM to the defaults.
If the problem is fixed afterwards, and you still feel brave enough to upgrade to WM5, then first repartition your device so that the extended ROM is empty. Instructions on how to do this from within WM2003 are found here :-
http://forum.xda-developers.com/viewtopic.php?t=50628
Figured Out A Solution
I figured out the problem and Im not sure if others have experienced this problem or not. Even if you dont created an extended rom on your Blue Angel when changing from rom to rom, if your screen tends to freezes after saying "tap on your screen to begin using your device" you will have to run the DOC repartitioning tool in the Prepartion Folder of some ROMS. Once running the program as the directions tells you and preform a reset even a hard reset on your device, everything will run fine without freezing.
hi there,
i have a BIG problem, so please, can someone help me?
when i enter the boot load screen (hold down volume buton and press power) it shows something like:
KOVS110
SPL-0.78.0000
MicroP1-787
MicroP2-707
Upgrade ROM code error
Please try again
and whatever i do, the same error ocured. I tried to install hard spl, but it gives an communication error, and it doesn't load, it remains at 0%.
i tried to put a ROM on my micro sd card, put it in the phone, reboot it but it sais "LOADING.....NO IMAGE FILE" and gives me the same screen as sown above.
The ROM version is this k|WWE|Dec 1|.¸¸.·´¯`·.¸¸.Energy.¸¸.·´¯ 6.5|21916 / 6.5.X|23149 * Sense 2019 - xda-developers.
I should mention that i followed some tutorials from this forum about how to reinstall windows step by step. if it metters how i get it broken, i tried to update the software using sony ericsson update service, it loaded the update bar, then all of the sudden, it shut down, and after that it keeps sowing the screen as shown above.
please, can u help me with this problem? thanks a lot, and sorry for my english, is not perfect.
hi there mate, Im no expert but I had the same problem.im no expert and you may have to wait for expert advice,....but......
I reformatted the memory card with MiniTool Partition Wizard Home Edition 5.2 it reformatted the card slowly, you can search the forums for" format card"and download a proper formatting programme.
I also had problems with the actual download once, i kept having the no image error come up over and over, so i re downloaded the file and it worked ,....also when they say take the battery out and wait,...do it for 10 secs.
ionut. said:
hi there,
i have a BIG problem, so please, can someone help me?
when i enter the boot load screen (hold down volume buton and press power) it shows something like:
KOVS110
SPL-0.78.0000
MicroP1-787
MicroP2-707
Upgrade ROM code error
Please try again
and whatever i do, the same error ocured. I tried to install hard spl, but it gives an communication error, and it doesn't load, it remains at 0%.
i tried to put a ROM on my micro sd card, put it in the phone, reboot it but it sais "LOADING.....NO IMAGE FILE" and gives me the same screen as sown above.
The ROM version is this k|WWE|Dec 1|.¸¸.·´¯`·.¸¸.Energy.¸¸.·´¯ 6.5|21916 / 6.5.X|23149 * Sense 2019 - xda-developers.
I should mention that i followed some tutorials from this forum about how to reinstall windows step by step. if it metters how i get it broken, i tried to update the software using sony ericsson update service, it loaded the update bar, then all of the sudden, it shut down, and after that it keeps sowing the screen as shown above.
please, can u help me with this problem? thanks a lot, and sorry for my english, is not perfect.
Click to expand...
Click to collapse
ionut. said:
hi there,
i have a BIG problem, so please, can someone help me?
when i enter the boot load screen (hold down volume buton and press power) it shows something like:
KOVS110
SPL-0.78.0000
MicroP1-787
MicroP2-707
Upgrade ROM code error
Please try again
and whatever i do, the same error ocured. I tried to install hard spl, but it gives an communication error, and it doesn't load, it remains at 0%.
i tried to put a ROM on my micro sd card, put it in the phone, reboot it but it sais "LOADING.....NO IMAGE FILE" and gives me the same screen as sown above.
The ROM version is this k|WWE|Dec 1|.¸¸.·´¯`·.¸¸.Energy.¸¸.·´¯ 6.5|21916 / 6.5.X|23149 * Sense 2019 - xda-developers.
I should mention that i followed some tutorials from this forum about how to reinstall windows step by step. if it metters how i get it broken, i tried to update the software using sony ericsson update service, it loaded the update bar, then all of the sudden, it shut down, and after that it keeps sowing the screen as shown above.
please, can u help me with this problem? thanks a lot, and sorry for my english, is not perfect.
Click to expand...
Click to collapse
hm, not sure if I'm 100% with you, but lets try:
the output you describe (SPL-0.78.0000) clearly shows that you are still on the latest stock spl, which you either got by factory default or through one of your later updates through SEUS (depending on how old your phone is)
this (stock spl) automatically prevents flashing of customizes roms (like the mentioned Energy rom), all you can flash with that are stock roms
there is the hard-spl thread concerning this by olinex which you most probably read and tried
so as I understand it you failed at flashing the hard-spl, then tried to run SEUS which failed as well and now you cannot even start your phone?
after failing at SEUS did you retry to run the SE update utility? it sometimes fails before successfully completing
did you try putting a stock rom on your sd card and flashing this (that would delete personal items and settings not backed up)?
how did you try flashing hard-spl? synching your phone with your pc and launching from there?
Best, DK
hi,
thanks for your post, and for trying to help. i should mention that i have never sync the phone with pc, i never need this. and i tried to hard spl the phone, but also gives error, it shut down. from then i tried several tims to do the update with the sony-ericsson application, it check's the phone and said that i have the latest software, but if there is any problem, try reinstaling the software. i push the reinstall button, it starts reinstalling, but the bar goes between 10 to 25, other time even 60 %, and then gives the communication error, and sais to try again.
i am no expert, this is the first time i try to do this on a phone, so if there is anyone who is so kind to explain step by stpe what i have to do, i shoul thanks him verry much.
So you want to install custom ROM to your phone? you need hardSPL first
If you have it hardSPL it will show 0.7.2.ollinex
then you just flash it. Try google how to hardSPL and FLash
simple mechanism,
X1 (Stock ROM and Stock SPL) -> hard SPL -> X1 (Stock ROM + hardSPL) -> Flash custom ROM (Energy ROM) -> X1 (hard SPL + Custom ROM)
WHY should Hard SPL?
because as DK explained above, SPL is the bios of your X1 and won't accept any ROM beside Stock ROM. so to have your X1, you need to change by doing Hard SPL, it will make your X1 accept any kind of ROM, stock or customed.
is it better to upgrade Stock ROM and Stock SPL to install applications? sorry, i'm just new in SE phone specially x1, so many things to learn here..
outlaw021705 said:
is it better to upgrade Stock ROM and Stock SPL to install applications? sorry, i'm just knew in SE phone specially x1, so many things to learn here..
Click to expand...
Click to collapse
They're both the same. Applications will install fine on a stock rom as well as a custom rom, there's NO difference. Think of it as jailbreaking an iPod Touch or iPhone, they can still install apps from the app store with no problems, NOTHING is changed.
In fact, think of it as a car. An normal car uses petrol. A car with a modified engine ALSO uses petrol. So there's no difference.
The difference between a stock and custom rom however, is huge. A custom rom is basically a stock rom, but modified. Custom roms gives you more customizability, just like jailbreaking an iDevice. Most of the custom roms run more efficiently, and a lot faster than a stock rom.
It's NOT hard to install a custom rom, you just have to read the guides properly and follow the simple steps. It's worth every bit of your time. Just follow the 8 steps here to install hardSPL:
http://forum.xda-developers.com/showthread.php?t=431218
and here if you want video tutorials:
http://forum.xda-developers.com/showthread.php?t=497511
And btw, the SPL thing is just the same as a jailbreak. It's a hack basically. Installing hardSPL will jailbreak your device so that you can install custom roms on it, it's basically "unlocking" the device so you can do whatever you want with it.
Hello,
I am a noob trying to install a rom with aroma installer. But now it has been stuck at the page where it says: The installation wizard has successfully installed *********. Press next to exit.
What do i do? Power off?
Is it definitely stuck? Aroma doesn't always recognise touch events very accurately, and I usually have to tap the "next" button a few times before it registers. Failing that, if it's finished installing whatever you flashed, you should be fine to reboot manually anyway.
Yes,i have tried to push the next button many times but nothing happens. It has been like this for 30 minutes now. The successfully installed text appeared very fast, a second or two maybe after the previous screen. So if it has installed the rom, it was def a fast install.
Anyway, is it safe to try to reboot, even if it was in the middle of the install? Rebot to recovery and try again?
Well, there certainly isn't anything else to be done besides rebooting. I don't know what you were trying to install - if it was a several-hundred-MB ROM, as most things that use Aroma are, you would expect it to take a while. Smaller things can be flashed very quickly. If it _did_ go wrong somewhere, there are a few things:
1. What recovery, and what version thereof, are you using?
2. Did you wipe data before using the installer?
3. Most of all, what were you trying to install? There might be some known issue with certain configurations.
I wouldn't necessarily expect a working OS when you reboot, depending on what you were trying to install and how badly things went wrong, but you should be able to get back into recovery easily enough.
Thank you for your quick reply.
1. I use the CWM recovery in this http://forum.xda-developers.com/showthread.php?t=1914394 thread, not the newest, but 5.5 something i believe.
2. Yes, wiped all data + dalvik.
3. I was trying to install rXTREME on my SGS III lte i9305.
I've rebooted now, and everything works perfect as the phone was before i tried to do the install. No brick. I also tried to flash it one more time, but stuck at the same place again. Rebooted fine at stock rom again. Maybe i should take this as a hint that someone else should be put at the steering wheel.. :laugh:
EDIT: forgot link above
Found out what the problem was.
In Aroma Installer i selected EFS backup both times. The third time i tried i did not do this. And everything went fine. Runs smooth.
my galaxy s3 international version got stuck at 30% of formatting\data partition while trying to flash s4 revolution 4.1 rom
what should i do?
jehad.drarjeh said:
my galaxy s3 international version got stuck at 30% of formatting\data partition while trying to flash s4 revolution 4.1 rom
what should i do?
Click to expand...
Click to collapse
This is I9305 forum is this your phone ??
This thread is about Aroma installer is that your problem ???
Suggest you read the basic faqs and guides first looks like from your post you are either flashing wrong rom to your phone or have hijacked a thread in the wrong forum ./
jje
I was struggling with setup wizard has stopped working and was fed up of this.
So i just went to the setup wizard app and gave it contacts and phone permission and it finally worked.
This error generally comes with CM roms so this fix will work with CM based roms and might work with other ROMs also.
Steps:
1) Flash ROM
2) Flash any gapps
If you get setup wizard error then continue the steps below and yes you need patience to do this because it will keep on popping up until you fix it. You need to keep on tapping and scroll down for a while.
3) When you see setup wizard error pull down notification drawer and open settings
4) Scroll down and tap "Apps"
5) Click on 3 dots at the top right corner.
6) Select show system apps
7) Scroll down until you see 2 Setup wizard.(If you have RESURRECTION REMIX ROM you will see only one)
There will be 2 setup wizard,one wil CM logo and other with android.
8) Select one with android logo.
9) Tap on force stop
10) Select ok
11) Scroll down and enable permissions(Contacts & Phone)
12) Now press the home button
You should now see your home screen :good:
It just a simple fix.
Because of permissions that were needed by setup wizard were not fulfilled this error keeps on popping up.
Hope you guys now have fixed this and got you CM.
Perfect (Y)
Thanks!
After hours flashing different versions of Gapps and getting this error I was about to give up when I found your post. Worked perfectly on my Galaxy S4, thanks man!
Thank you very much!
You saved my day
You're a GENIUS !
wow and WOW !!!! It works as a charm. I was about to throw my SG3 away from the 12th floor.... Thanks again my angel.
I always wipe system before flash rom
N never get error setup wizard
Btw
U genius bro
I can't pull down the notification bar more so that the settings icon appears
You saved my life ! thanks a lot !
You are life saver. Thanks man higly appreciiate this.
I hv force stopped setup wizard in resurrection remix rom ..
But the permissions are already enabled,!!
Help me guyzz i cant come to home screen!!
Cool. Updated my p5210 to latest CM13 and kept getting 'google play services has stopped'. Tried to reflash CM and latest gapps. That's when I got 'setup wizard has stopped' message. Spent a long time wiping and refreshing. Then I found your guide, and now all's honky dory! Thanks a lot
thanx a lot... it solved my headache...
Thank you very much!
Thank you very much!
Massive Thanks
You save my days bro, thank you very much. Im using Mi4 LTE-CT AOSP ROM Android 6.0.1. You solved my problem. Again thank you very much!!!!
Hi .. when i click on permissons it said : unfortunately package installer has stopped and when i push home key setup wizard error appears again please help me.....
Sorry for bad english
I have another problem please help me.. When i install resurrection remix to again marshmallow rom.. Then setup comes and i choose language english then press next.. Suddenly error comes that setup wizard has stopped and back to the language screen again n again same error when i click on english then next button.. Then i come back on resurrection remix again please help im so confused what can i do
Not able to access notofication bar
Hi
This sounds helpful but I'm unable to pull down my notification bar at least and can't do anything further. I'm facing this issue after factory reset. Device name: Spice Android One
Please help me out.:crying::crying::crying:
VenkatGo said:
Hi
This sounds helpful but I'm unable to pull down my notification bar at least and can't do anything further. I'm facing this issue after factory reset. Device name: Spice Android One
Please help me out.:crying::crying::crying:
Click to expand...
Click to collapse
what rom?
if thats custom rom with gapps? then thats gapps issue. just reflash the rom, use opengapps.org for the gapps.
if its stock, then look here, get the stock rom zip and flash it via twrp, a clean install recommended. :good:
Setup Wizard too fast to click anything
I was hoping the solution posted here would solve my problem as well, but it did not.
Clicking the "OK" on my "Setup Wizard" screen dismisses the box for 0.25ms. I have NO chance to click anything else or get to settings to Force Stop it.
Sigh.
Any other suggestions?
FIX :
Flash RR ZF6 via TWRP
Flash Gapps ( Download open gapps x86 6.0 pico only 78 MB)
Wipe
Reboot
And Voila The Wizard Has No Error Again :good:
Hi everyone! I have been suffering with this problem for 2 full days on my S10 (SM-G973F/DS) and now i just have absolutely no idea how to fix it, so I thought it was worth writing about it here.
On stock, I used one old and outdated application that made user certificates system certificates, but which worked. Having tried it on EvolutionX 5.9.1 (Android 11), it brought the phone into a bootloop. I didn’t have a backup and because in order not to go through the installation process on a new one again, I decided that I would try to delete the folders from the data partition ONLY, but after half a day of attempts, nothing happened and I started to install the rom from scratch, but then weird things began to happen: after reinstallation/factory reset, boot animation randomly started (check attached video), which either went into an endless boot, or loaded the system back, but then if boot animation started on loading then this loading become endless, and the buttons (in the system) "Reboot to recovery", "Reboot to bootloader" and etc simply turning off the phone without booting into the recovery or bootloader, and if this happened, then somewhere in 2 minutes after turning it off.
I think i tried almost everything: re-installation according to the instructions, re-installation according to the way I did it before, I even tried to install the stock, and after the recovery again and then rom, but absolutely nothing changes, I cannot use custom rom if it is up to this worked fine and everything started on the same version as I was trying to install like before, I even tried to download the rom installation file again, not installing magisk-patch in boot, installing multidisabler, even find my old backup for TWRP that has every partition, but absolutely nothing changes, maybe someone knows how to fix it?
Thanks in advance!
P.S Stock rom works perfectly (android 11), but i want to use custom anyway (also android 11)