Related
Hi,
I just upgraded to 1.40 rom and noticed that once I turn off wireless from the wireless manager, i can;t turn wireless back on until I reset the device. Is anyone else having this issue?
Thanks,
Skumky
Yes and no.
I've experienced the same problem, but I've also had it with 1.12, 1.22, 1.31 and 1.33 too so I'd comfortably say it's not specifically related to 1.40.
I've also had this problem with the following radios: 1.02, 1.06.02, 1.08, 1.10 and 1.12. (I like to upgrade hehe)
Sorry that wasn't much help, but really just trying to say I think it's more a bug with the operating system itself and not a specific version. Perhaps combination of software affects it and thus you've never had it before. I don't know :-(
I have also upgraded to 1.40 and the wi-fo worls perfectly. I dont face your issue.
I have also upgraded to 1.40 and the wi-fo worls perfectly. I dont face your issue.
I've experienced this with the 1.40 and 1.12 radio.
No problems to report here about the WiFi-module. Works fine. Is it related to the security-level that you run on your WiFi-network? I use an 64-bit WEP-encrypted protocol, and leech on open networks , so more then 64-bit it won't get. Maybe an increased security-protocol causes the system to hang?
No problems here. I did have that problem in an earlier rom combination however.
1.40 WIFI
I had the same problem, so I ran the WLANPatch.CAB from the Cingular update. This cured the problem, so I put it in my extended ROM and did hard reset but the problem came back. As a temporary solution I just rerun WLANPatch.CAB after Hard Reset and no problems so far..
I have that problem all the time. When my wireless manager reads "not connected to network" before I turn it on, it usually works, but after I've turned it on and off again it says "wireless off" instead, and then there's often no way to get it to work again.
I have a feeling this is caused by Omega One Battery Pack's custom "ok" button - I guess it closes the app in an incorrect way. What I usually do is tapping Start->Today instead of "ok" to exit the wireless manager after I've turned wireless on or off. This seems to solve the problem most of the time.
same problem here as well. Was trying for the last hour to turn wifi on, no go. Did a soft reset and wifi was already enabled when it startled back up. This has happened to me with previous roms as well. Guess its a "feature" of the phone.
SBP Pocket Plus will cause this also (customized close)
Has anyone tried my suggestion? Make a habit of just tapping "start :arrow: today" instead of "ok" each time you use the wireless manager and the problem should occur a lot less. If it does occur, the only way out seems to be a soft reset.
Also, does anyone know of a more structural way of actually solving the problem instead of working around it like I do?
Yeah. Don't turn it off!
Don't Turn it Off..
The only problem with that is that when you drive down the road, it tries to connect to everyone's wireless network and keeps popping up those ' Do you want to connect to John's' network' boxes...
Exactly! That's the fun part! And around 70 % of those networks, at least here in Norway, are totally unprotected! :twisted:
Ah!... so now I understand what "free internet" means in those Norweigen commercials :wink:
Hi guys and girls.
I finally plucked up courage to install WM5 and suprisingly, it worked like a charm! not one single problem
There is one cherry on the top that would be very nice if anyone can help.
On the today screen there is a nice little bluetooth icon in the bottom right hand corner; is there any way to get a wifi icon next to it instead if having to go into start > Settings > connections > WLAN to turn it on?
Appreciate any suggestions offered.
Cheers
J
can someone please send me the orginal wirelessmgr.exe file? i tried to load the wirelessmgr.exe from the universal and now i cant turn wireless on or off
Codiac, I have taken a hotkey (camera, I don't use that much anyway, but any key would do) and mapped that to WLAN_MAN. Works very nicely, but I hope there will be a fix for the dissappearing WLAN (and BT, even though that doesn't matter that much to me since I never turn off the unit when I'm using anything BT) in the near future.
I never thought of that works spot on now :lol:
Must remember in future to engage brain before fingers :?
Cheers Mastiff
J
I added the program into O2plus apps tab
Codiac said:
On the today screen there is a nice little bluetooth icon in the bottom right hand corner; is there any way to get a wifi icon next to it instead
J
Click to expand...
Click to collapse
Codiac... how did you get the bluetooth icon on the Today screen? I just upgraded to Mamaich's Patch 5 but I don't have a bluetooth icon
me too..i can't see the bt icon and sometimes i quicly need of it..how can i show it?
Read the Wiki about missing files, patches number 1: http://wiki.xda-developers.com/index.php?pagename=BA_WM5_Patches_ChangeLog
This is wierd?!?
After I did the upgrade the nice little BT icon was on the today screen, never bothered with it because BT is useless. Read these posts and had a look to see if I could work out how it got there and it has dissapeared?!?
The only thing I can think of is that I accidentally uninstalled one of the patches downloaded from wiki.
ill try and get it back on and let you know how I did it
Cheers
J
OOPs, sorry should have read Mastiffs post properly first
Mastiff is right, you need to install ba_wm5_fix_v1
Cheers
J
Well I've installed the BA_wm5 patch, but still have wifi problems. On 2003 my BA used to turn on wifi every time i turned on the unit, great as i have wifi at home and at work, now it always defaults to off and I have to switch it on every time I've turned off my BA. It's driving me nuts as I use email via wifi at work all day. Is there any way to get the wifi always on? Please....?
That's what I've been *****in' about for more than a week now...
Surely there's a way to default wifi to on, here's hoping somebody works it out before i downgrade to 2003.
i douwngraded to wm2003se..wifi on wm5 don't work at all..dosn't connect on my AP (on wm2003se is very fast)..so..because i need it i'll wait a more stable version..perhaps backlight regolation will be fixed
Backlight regulation was fixed more than a week ago! And I don't really know why you have WiFi problems, I have only one problem, that it defaults to off.
Mastiff said:
Backlight regulation was fixed more than a week ago! And I don't really know why you have WiFi problems, I have only one problem, that it defaults to off.
Click to expand...
Click to collapse
The default to off is the problem. I use my BA for work only. At home I use my wifi network to access work schedule appointments, and when in the office I use their wifi hotspot. At present i am having to tun on wifi realistically around a hundred times a day to update my joblist.
Is there a way to add any sort of utility to startup to turn it on at power on maybe?
I've tried everything to make my WiFi work but no luck.
However, I think I'll hold on because I really like WM5. I've ran through all the registry setting but nothing I've tried so far has made a difference. Enev tried downgrading the encryption settings on my MIMO. Furthermore, when I take off SSID broadcast, my BA seems to be able to see the AP but still fails to connect.
It's really annoying because I like to synchronize Avantgo over WiFi and most importantly use my BA when I'm in the bathroom doing you know what. Somebody please help!
Hey Mastiff, what security settings have you got enabled on your Access Point?
Mastiff said:
Backlight regulation was fixed more than a week ago! And I don't really know why you have WiFi problems, I have only one problem, that it defaults to off.
Click to expand...
Click to collapse
Cytrax, did you install activesync 4 to upgrade your rom? You can't sync by wifi on activesync 4 at all, they've removed the option from the program!
cytrax, I have 64 kbit WEP and MAC access control since the 128 kbit WEP was slow to access with another CE unit I have.
Thanks for that info, mastiff.
OK, this is wierd! At this particular point, WiFi works on my BA. However, it only works when I'm at work. The settings configured on Work AP is very similar to what I've got at home. The only difference is I use Netgear MIMO at home while Buffulo Airstation is deployed at work. This is really freaking me out (well, not exactly, but it's annoying).
I also tried with an old Belkin AP last night but didn't get any luck. I think I'm going to try 64bit WEP once I reach home. Watch this space!
Mastiff said:
cytrax, I have 64 kbit WEP and MAC access control since the 128 kbit WEP was slow to access with another CE unit I have.
Click to expand...
Click to collapse
Update on my WiFi problems:
I have now installed windows mobile 2003SE, anmd when I turn on WiFi the yellow light flashes, indicating it is on, however windows mobile doesn't display the wifi icon, or search for networks. The "eggtimer" icon comes up for a few seconds, and I am then taken back to the today screen.
I can't believe it is a hardware problem, as the light is flashing.
Any ideas?
Thanks,
Tom
come on guys, what do I need to do to make it work?
Is it a repair I need? Can you reccomend a company to do this cheaply? (I am only a poor student)
hmm, i know some ppl has problem with wifi but try this.
flash your BA with helmi vanilla version (with no extrom) and try to turn on wifi then.
if it's still not on, time to get it repair.
Could you recommend a good (cheap, reliable) site to get it repaired at?
EDIT: Was this caused by using wm5? If it was, I'd rather not try using it again! Not worth the risk!
Come on guys, surely u can reccomend a site to get it fixed at??????
Or could I buy the part myself?
I've tried it all!! The wifi will not turn on at all. In the settings tab and under connection, the comm manager wifi switch pressed will cause the wait cursor to come up, but after the process it wont turn to on. Can anyone please help me.
how do u know its not on? cant detect wifi?
Is the Wifi antenna icon comes up on the top menu ?
Baronic said:
how do u know its not on? cant detect wifi?
Click to expand...
Click to collapse
Not Sure What you mean.
1. Go to comm manager
2. Hit WiFI and the wait icon starts (should be a quick spin and its on, but the icon goes on for a while).
3. Switch instead of turning green animates back to off.
I have not loaded anything other then SKtools that could change the registry or system in anyway (no other tweaks except Schapp's)
I looked all over this forum and found tricks for other HTC phones, tried one or two, but they are made for other phones. I looked over the GPS and in Google Earth disabled it. I have also done a hard reset. I also get a device.exe error.
Please somebody help us. My diamond's wi-fi doesn't work. I try a lot of tfink. I try a lot of time hard reset. And several times upgrade diffrent roms. Now i use 1.37.401 europa rom. But my diamond's wi-fi still not work.
same here.. any news?...
Juggy said:
same here.. any news?...
Click to expand...
Click to collapse
Did you set your battery for best performance in the wifi configuration? If not, try it and see if it works then
Yes.. the wifi is not working ,... the same for the gps...
Mines the same. Done a soft reset - nothing. Done a hard reset and all seems fine for the mo.
Got my phone from orange.
hard reset u mean erase all and start like new?
with this hard reset.. the same problem... any other option??
No Wify
I have the same problem. No wify. A "device.exe" error appear. Is there any solution?
WLAN Hardware
minlu said:
I have the same problem. No wify. A "device.exe" error appear. Is there any solution?
Click to expand...
Click to collapse
I have the same problem with german htc touch diamond and several roms.
I think the hardware has an error. Bull**** !!!
Has anyone an other idea?
I had this issue with my S710, if you turned the wifi on it would flip to on for a second before going back to off - only happened if I has it hooked up to a pc via usb. Not sure if its the same with the diamond?
I couldn't enable Wifi properly on my last phone despite hard and soft resets. After trying lots of times, I gave up and sent the phone back to Orange. I currently have a Diamond Touch that has no problems enabling, but can't connect to my router using WPA2.
I think I have the solution for wifi / wlan problems on diamond
Over one week i try to start my wifi (100 hardresets, 5 new ROMs) and then i believe it is an hardware error.
Under ...\connection\wifi\ was not the tab "wireless", only the tab "networkcards"
My last try was the solution:
1. In my HTC Kaiser is the same wifi-hardware
2. I export the registrykey "HKEY_LOCAL_MACHINE\Comm\TNETW12511" from the kaiser to a .reg-file
3. I delete this registrykey on the diamond and import the .reg-file from the kaiser
4. Before I can start wifi i make about 5 softresets and try to start
5. But the start was only successful when I make first a connection to the pc with ActiveSync and then a softreset
This is my solution, please answer me when it works for you too
One problem is still there: after an usb connection wifi will not turn on. I must make a softreset but thats no problem for me.
Its the same what "huwwatkins" describe at #13 with the S710
Here is my regfile from kaiser
zmob123 said:
Not Sure What you mean.
1. Go to comm manager
2. Hit WiFI and the wait icon starts (should be a quick spin and its on, but the icon goes on for a while).
3. Switch instead of turning green animates back to off.
I have not loaded anything other then SKtools that could change the registry or system in anyway (no other tweaks except Schapp's)
I looked all over this forum and found tricks for other HTC phones, tried one or two, but they are made for other phones. I looked over the GPS and in Google Earth disabled it. I have also done a hard reset. I also get a device.exe error.
Click to expand...
Click to collapse
I have heard of this... The wifi does not go on but the bluetooth does. I was told it was a bad chip.
same here, called retailer today. told me HTC is working on a fix. will be available in about two weeks. let ya know
Same problem here..
I have the same problem. Tried everything - no luck. Thinking of turning it in for repair - should I flash the original SPL/ROM for warranty reasons or can they tell it's been flashed anyway ?
wifi working fine on mine
i have no problems at all
huwwatkins said:
I had this issue with my S710, if you turned the wifi on it would flip to on for a second before going back to off - only happened if I has it hooked up to a pc via usb. Not sure if its the same with the diamond?
Click to expand...
Click to collapse
Yes my diamond has this also only when plugged with USB.
Grtzzz
Hi all,
I wonder if anyone can resolve/give suggestion for my problem.
Basically i have experience problems connecting via Wi-Fi i.e the after activating wi-fi the phone will scan for available networks and give you the list. I then try to connect to my router (bt home hub which is actually speed touch) it does connect and stays connected for some time then suddenly the connection is dropped and under wifi it says that my access point is unavailable. If i turn wifi off/on again and scan for networks it comes up with "No visible Networks detected" even though there are like 5 access points in my house and i can connect to any of them using my laptop and old nokia e60. If i wait a while it will connect again but will not keep the connection. I have tried at home, work and some public places-every time is the same story.
Things i tried:
Soft reset/hard reset (many times)
Tried disabling phone radio in case3g chip interrupts
I tried with secure networks, open networks, different types of authentication/encryption, different router (more than 10) and every its the same story. I also tried several ROMS and ALL RADIO's available with the same result.
I am currently on Duttys_Diamv2.3 WWE RADIO 1.00.25.08, its a clean flash, nothing else is installed. I also have SPL-1.40Olinex installed (not sure if that could have an impact) The phone is vodafone branded btw (i had the same issue with vodafone rom which is why i decided to try other roms). I wonder if anyone has any thoughts/suggestions and would appreciate any help. Thanks in advance.
The same situation happened to my Diamond. I took it to the local dealer for HTC and after several days, I am told that the main board will need replacement. I am still waiting for it to be repaired as the parts had to be braught in from another country. I was also saud if the phone was less than a month old (which it is not) they would have replaced it with a new phone.
Good luck repairing yours and keep us updated.
omar302 said:
The same situation happened to my Diamond. I took it to the local dealer for HTC and after several days, I am told that the main board will need replacement. I am still waiting for it to be repaired as the parts had to be braught in from another country. I was also saud if the phone was less than a month old (which it is not) they would have replaced it with a new phone.
Good luck repairing yours and keep us updated.
Click to expand...
Click to collapse
Thanks Omar, I was kinda thinking that it may be hardware issue, but I don't anymore, I am trying something else actually as we speak. The only thing I haven't tried before is another hard SPL and I think that's the problem, I installed another version hspl1.34 and it seems more stable now and wifi keep connection, also with another hspl version (it was hspl 1.24) RAM under devise info>hardware showed 128, now it is 192. I will test in intensively and post my results here in case nay one else have the same issue. Hopefully I will not have to send it away for repair. Thanks for your info anyways.
In risk of sounding lame ...
Have ya tried 'Start' / 'Settings' / 'System' 'Wireless LAN'
Under Wireless LAN click 3'rd tab (strømtilstand in Danish - could be power-settings)
On that tab - pull the marker way to the left in order not to minimize the power consumption when tryng to hookup with the WiFi.
I had massive problems to get my local WiFi working at home - until I did this trick.
Best luck, Kindly
Kwasmir said:
In risk of sounding lame ...
Have ya tried 'Start' / 'Settings' / 'System' 'Wireless LAN'
Under Wireless LAN click 3'rd tab (strømtilstand in Danish - could be power-settings)
On that tab - pull the marker way to the left in order not to minimize the power consumption when tryng to hookup with the WiFi.
I had massive problems to get my local WiFi working at home - until I did this trick.
Best luck, Kindly
Click to expand...
Click to collapse
Yes i have thats the first thin you do anyways . I am now more than sure that the issue was with HSPL version 1.34, as soon as i got rid of it (installed hspl 1.24) all is fine.
With my phone, i tired all Hard SPL versions and even went back to stock SPL & Rom 1.37 & 1.93 and it still didn't fix the WIFI issue. it will work for 5-15 minutes then it will not work.
Anyway, I got a replacement phone as apparently they couldn't fix it.
pufeks said:
Hi all,
I wonder if anyone can resolve/give suggestion for my problem.
Basically i have experience problems connecting via Wi-Fi i.e the after activating wi-fi the phone will scan for available networks and give you the list. I then try to connect to my router (bt home hub which is actually speed touch) it does connect and stays connected for some time then suddenly the connection is dropped and under wifi it says that my access point is unavailable. If i turn wifi off/on again and scan for networks it comes up with "No visible Networks detected" even though there are like 5 access points in my house and i can connect to any of them using my laptop and old nokia e60. If i wait a while it will connect again but will not keep the connection. I have tried at home, work and some public places-every time is the same story.
Things i tried:
Soft reset/hard reset (many times)
Tried disabling phone radio in case3g chip interrupts
I tried with secure networks, open networks, different types of authentication/encryption, different router (more than 10) and every its the same story. I also tried several ROMS and ALL RADIO's available with the same result.
I am currently on Duttys_Diamv2.3 WWE RADIO 1.00.25.08, its a clean flash, nothing else is installed. I also have SPL-1.40Olinex installed (not sure if that could have an impact) The phone is vodafone branded btw (i had the same issue with vodafone rom which is why i decided to try other roms). I wonder if anyone has any thoughts/suggestions and would appreciate any help. Thanks in advance.
Click to expand...
Click to collapse
...I have the same problems with you
However, I think the problem may caused by different ROM versions.
My hTC version Diamond initially flashed a Chinese version ROM, and the WiFi connects well, while I changed to Dutty's most updated ROM, this problem comes and I cannot figure out why untill now.
Some friends also suggested to go to the Power Management and change WiFi to "Best Performance", I tried and failed again.
WiFi can open and connect to Routers located in library of my university, nevertheless it cannot open any pages.
I'm also waiting for any person that can solve the problem and then help us figure out why....
thanks in advance!
I got the same problem as most of the people have. and i think "Fail to turn on wifi" is a very common among guyz who got HTC TD.
I dont know what should be done, i almost tried every thing. actually my phone was locked to 3 mobile Sweden and i unlocked it but my wifi was'nt working before unlocking too but i did'nt gave attention to it. Now i noticed it.. is that any one know how to lock it again soo that i can send my mobile for repairs or, any one know what should i do.
I would recommend upgrading your radio and your rom.
Ive been rocking the setup in my sig for some weeks now and its been flawless, stable and fast.
which rom and radio you are using. can you please help me in this matter.
and i think its not a hardware problem because its showing that hardware is connected to my device as its shown in the screen shoot
Hi,
Im using AlphaZero V7 NLD,
Im have 1 wifi point in my house, downstairs.
even when im on the attic i have 80% signal strengt.
My router is a draytek 2820G router.
Wifi for me is very good. .. correctly, AZTOR V7 NLD is very good for me.
im on t-mobile network.
Radio Radio v1.00.25.05 , Radio v1.00.25.08, Radio v1.00.25.16, where all good,
now testing Radio v1.08.25.20, HDSPA signal is bit weaker atm.
my best radia atm i think, v1.00.25.08.
im betting, that the starter of this toppic, who has 5 access points in his house all have the same SSID. This is not the way.
Or make 1 big AP aera, bij connecting the AP's to each other.
of try to set every AP its own SSID, and its own Channel.
Louis
WIFI problem in HTC Diamond.........
I am trying connecting to my home wireless network. It finds the network but unable to connect to it. Any help please? Has anyone managed to get it connected to any Wifi? I ahve already set the power management to "best performace...no succes.......
(My laptop and O2 stealth does get connected to the same network and it an open wifi connection)...........PLZ Help.....
pranavsethi said:
I am trying connecting to my home wireless network. It finds the network but unable to connect to it. Any help please? Has anyone managed to get it connected to any Wifi? I ahve already set the power management to "best performace...no succes.......
(My laptop and O2 stealth does get connected to the same network and it an open wifi connection)...........PLZ Help.....
Click to expand...
Click to collapse
i am also having this problem, it can find the network, and can spend a minute or 2 trying to connect, and nothing happens. you posted this in february, did you find an answer?
Wifi & Bluetooth not detected by HTC Diamond
Someone pl help. My HTC Diamond is not detecting bluetooth devices neither is detecting wifi. It was earlier doing so and working fine however I believe after installing tweak TD & t3d config it has stopped working. I have installed new ROM also but to no avail. Can someone pl help!!!!!!!!
Wintermoonlight said:
i am also having this problem, it can find the network, and can spend a minute or 2 trying to connect, and nothing happens. you posted this in february, did you find an answer?
Click to expand...
Click to collapse
i also have the same problem. it detects a wifi (my router at home Aztech brand), then trying to connect to it, and then it always showed the wifi as "unavailable". i put my phone 2 mm distance from the antenna of my router it also won't connect. i have change dozens of roms, win 6.1, 6.5, 6.5.1, different cook, MTTY, all with no success.
i've looked for internet and google for answers, i seen quite a lot of forum has described this issue, but with no solution. most of the ppl suggest in various forums to pull the wireless slider to "Best Performance", ofcourse i have done that, but is just the same result.
i'm still trying searching for a solution for this, i hope is not a hardware issue because my warranty has already ended. i'm currently using Gen Y R4.1B rom
pufeks said:
Yes i have thats the first thin you do anyways . I am now more than sure that the issue was with HSPL version 1.34, as soon as i got rid of it (installed hspl 1.24) all is fine.
Click to expand...
Click to collapse
Ok consider now wifi will work by re-flashing the spl.
But what is the relation between spl (os/winmo loader) with wifi?
another dang unsolved diamond wifi?
bravo.
same problem with wifi on diamond2
With Original stock WM6.1 i was unable to connect at all, after flashed official WM6.5 upgrade everything worked fine. However i decided to put cooked rom because of battery life and perfomance issues. Dutty HG6 for Topaz seems to be with glitchy radio, it works sometimes, very rare, and i'm still not up to the pattern when does it happen and why. Pretty sure it's not a hardware problem - so everybody relax, we will find the solution.
which rom and radio you are using. can you please help me in this matter.
and i think its not a hardware problem because its showing that hardware is connected to my device as its shown in the screen shoot
wjenya said:
With Original stock WM6.1 i was unable to connect at all, after flashed official WM6.5 upgrade everything worked fine. However i decided to put cooked rom because of battery life and perfomance issues. Dutty HG6 for Topaz seems to be with glitchy radio, it works sometimes, very rare, and i'm still not up to the pattern when does it happen and why. Pretty sure it's not a hardware problem - so everybody relax, we will find the solution.
Click to expand...
Click to collapse
nope, i also put Gen.Y WM6.5 then the problem still arise.
i'll wait any solution until my diamond is totally wrecked