Related
I have installed the 1.12.10 GSM on it after making backups with aWizard. I am happy to report that it does work and that it does speed up the initial connection. Before (with 1.09.11 I beleive) I could log into (enter my PIN) and would still have some time before I would connect and get signal bars. It also seemed to increase refresh rates of the bars. Now the signal is usually found before I even finish entering my PIN muchless the today screen loading.
These tests were made in my basement at my house where I typically have been getting 1-3 bars. now to test 1.13.10 and 2.8 OS to see if it works.
I will say I thought it broke at first because I couldn't get my PC to talk to it after it reloaded, then I did another soft reset and the boot screen the second time didn't list the GSM version, even though the OS did see and use GSM. I re-ran the CID unlock procedure again since I could talk to the phone again. Reset again and GSM ver was on the boot screen again.
I also swapped out the boot screen for a bmp and that worked wonderfully. my only question is if there is a way to swap out the booting screen of the OS and not just the IPL Rom.
cheers,
ET
I have just done the RUU install of 2.16.9.101 which also upgrades IPL/SPL to 2.16. It changed my radio version to 2.7.10 and my protocol version is 413.1.0.3. This ROM date is 2/6/06.
Immediate differences are the battery notification is now at the top where on Cingular's ROM it was at the bottom next to the comm switch program. That and everything is I-Mate branded. No Get Good, but instead now I have I-Mate backgammon and Skype. And instead of the Cingular Mail link now there is an I-Mate mail link.
I will update later with more.
More... OS ver 5.1.195 build 14847.2.0.0 IDK if this is different or not.
Update 11AM: I have tested more. ZPhone themes I can't seem to install... IDK why but with the original Cingular ROM I couldn't either. The original ROM had a bug that used the proxy of the modem setting on the wifi setting making wifi not work unless you went and disabled it since it is enabled by default. This new rom after installing "Cingulcustomize_No_Emails.cab" to get MediaNet back, wifi just works. Even with the Proxy set on the modem connection. My Bluetooh headset (Jabra HT800) works great. Comm Manager is real nice. Even showing you the status of SMS and GPRS/EDGE connection. I want to play with it a little more to see if I can control those two or not. Gone from teh Cingular ROM is the ability to click on the Edge status icon in the notification area and tell it to turn on Wifi. But the Turn on Flight Mode still exists under the Cell Strength bar. Signal strength is comperable to the 1.12.10 radio rom I had before the upgrade. And IDK if it is taking longer to load from a reset or not, but before the Phone radio would be up and running just as I was finishing putting in my PIN unlock. But now it is running and connected before I can even start to input it. Just observation, that extra second doesn't mean anything.
I also have the 8125, so I am curious if the Imate ROM will cause any problems after the upgrade. I am not sure I want to wait a few more months until Cingular gets around to providing their upgrade.
Some other posters with the test/beta Qtek AKU 2.0 rom reported that they had trouble with the device resetting itself and problems with Wi-Fi. Let us know if you experience any issues with this ROM.
How has EDGE speed been, any improvements over the shipped ROM? Have you tried push email?
ok, i updated my 8125 to the new rom and am having two issues atm. first, the phone signal icon and the battery icon on the today screen is cut off so i only see the edge icon. secondly, i cannot start wifi at all, no matter what i do :\ (it looks like it's thinking but doesn't actually turn on ) now i did apply the cingular extended rom to this so i dont know if that caused both issues or not. as for edge performance, i'm in an area with bad signal so i couldnt exactly test it. i'm going to be clearing storage tonight and see if that fixes both issues or not. i haven't tested push e-mail as clubimates servers AREN'T supporting direct push (ie they don't have SP2 installed or have it enabled on exchange).
Locked up
Well I am noticing that it is locking up if I let it sit for a while to where I can't bring it back up. I have disabled the lock code to see if that fixes it.
I would have a feeling that the problems you are having are because of the enhanced rom difference. it won't hurt to try it as is like I did since you are having problems with it.
were can I fine install
I look for the rom in the ftp but there is no RUU install of 2.16.9.101 can you please tell me where can I fin this rom
thank you
Here:
http://forum.xda-developers.com/viewtopic.php?t=42638
Scroll down to HTTP server link.
Cheers
thanks
thank you for giving the info on where to get the link. I have been away from a pc today.
as an update: the phone seems to be stable with the new rom (I am actually using the phone now using edge and it seems faster than my old phone was which was a nokia.)
I haven't had it lock up on me since I uninstalled battery pack pro, disabled lock code, and uninstalled skype & backgammon so take your pick as to what fixed it. I will do some more expereriments to try and figure iit out.
later,
ET
Are you having the same issues as darkjedi who said he's having problems with WiFi and signal strength icon?
after the upgrade i cant find the GPS ICON
even i try to delete the redirect string in the registry like i used to do before
still i cant see the icon on my setting page
please anyone noticed this problem ?
tx
exchguy said:
Are you having the same issues as darkjedi who said he's having problems with WiFi and signal strength icon?
Click to expand...
Click to collapse
i finally fixed the signal strength icon (but don't ask me how), but wifi is still borked
no more problems, lock ups or otherwise
My guess with my problems were related to Battery Pack Pro demo. Even on the original rom I couldn't get it to work right with the assignable hard keys.
Anyway, I did not modify the original EXE one bit like darkjedi said he did. He seems to be much more advanced as I don't know how to do what he did and not that familier with its registry settings yet. But I naver had any problems with Wifi nor with icon placement.
My home wifi does use WPS-PSK TKIP using a Netgear WG302. Battery life seems good, but I do get a little crackle every now and then on my end of the bluetooth handsfree. People I talk to haven't said they hear anything other than perfect clarity. I would have been told if they heard anything since part of my reason to spend the money now rather than later was my voice and signal quality on my old Nokia was getting to be bad and they wouldn't waste a second ragging me if voice and signal problems were re-appearing. But mostly the crackle is few and far between and usually when my headset is on the other side of my body or I am a few feet away from my phone.
i didn't modify the original EXE, i installed it as normal, then after the fact, copied the cingular extended ROM then installed each cab manually. i didn't get a chance to try wifi before i applied the extended rom, but i just might hard reset and try that.
i dnt see the rush to upgrade if u have a cingular 8125 since there goa offer rom upgrades for the unit. with all the bugs i rather just get a ad2 bt plugin (wish they made it) and just do that
what roms do they offer? On my past phones I have had to have major problems before they would flash a new version of the Rom (my last 2 symbian phones).
darkjedi said:
i didn't modify the original EXE, i installed it as normal, then after the fact, copied the cingular extended ROM then installed each cab manually. i didn't get a chance to try wifi before i applied the extended rom, but i just might hard reset and try that.
Click to expand...
Click to collapse
ok... the only cab I installed for Cingular was the one I mentioned earlier. I have since installed spb power plus and their weather app and I am still stable. Not one failuer and my bluetooth is actually acting better from some reason. I was working on my car today with teh phone in the car and I was about 10 feet away without any noise or other problems.
Re: thanks
ethorn said:
thank you for giving the info on where to get the link. I have been away from a pc today.
as an update: the phone seems to be stable with the new rom (I am actually using the phone now using edge and it seems faster than my old phone was which was a nokia.)
I haven't had it lock up on me since I uninstalled battery pack pro, disabled lock code, and uninstalled skype & backgammon so take your pick as to what fixed it. I will do some more expereriments to try and figure iit out.
later,
ET
Click to expand...
Click to collapse
Is there any settings to configure edge? I only see GPRS in the connections section.
This version appears quite stable but's only my second day since upgrading my 8125 from the QTECH 2.8.7.102. I really like the Comm manager and the Push Email icon works great.
Thanks!
name of account
the only thing that I have notice so far is that the name of my celular company (I could see before upgrade) now i only see numbers.
exchguy said:
I also have the 8125, so I am curious if the Imate ROM will cause any problems after the upgrade. I am not sure I want to wait a few more months until Cingular gets around to providing their upgrade.
Some other posters with the test/beta Qtek AKU 2.0 rom reported that they had trouble with the device resetting itself and problems with Wi-Fi. Let us know if you experience any issues with this ROM.
How has EDGE speed been, any improvements over the shipped ROM? Have you tried push email?
Click to expand...
Click to collapse
On the new imate ROM I'm getting between 65 and 110 kbps on edge. Latency is still crap at about 1.5 seconds on average, but that's what it's always been for me.
Direct push is great. Assuming you have Exch SP2 installed, push works without any other changes. I'm averaging between 7 and 10 seconds for an entry to push out after it gets to Exchange. I haven't installed the device management tools yet, but I'll do that soon and let you know how well they work.
I just noticed wifi isn't working. If I enable it in comm manager, the button is ringed in green as if it's on, but the left green led does not blink and it does not detect my open, unsecured access point. I did install the cabs from my original cingular extended rom, and one of those appears realted to wifi, but not sure what it does. I'll mess around some more and see what I can do. I'm not totally heartbroken that wifi is messed up, but it does bug me that I don't know why it aint working.
Need Cingulcustomize_No_Emails.cab file
ethorn said:
I have just done the RUU install of 2.16.9.101 which also upgrades IPL/SPL to 2.16. It changed my radio version to 2.7.10 and my protocol version is 413.1.0.3. This ROM date is 2/6/06.
Immediate differences are the battery notification is now at the top where on Cingular's ROM it was at the bottom next to the comm switch program. That and everything is I-Mate branded. No Get Good, but instead now I have I-Mate backgammon and Skype. And instead of the Cingular Mail link now there is an I-Mate mail link.
I will update later with more.
More... OS ver 5.1.195 build 14847.2.0.0 IDK if this is different or not.
Update 11AM: I have tested more. ZPhone themes I can't seem to install... IDK why but with the original Cingular ROM I couldn't either. The original ROM had a bug that used the proxy of the modem setting on the wifi setting making wifi not work unless you went and disabled it since it is enabled by default. This new rom after installing "Cingulcustomize_No_Emails.cab" to get MediaNet back, wifi just works. Even with the Proxy set on the modem connection. My Bluetooh headset (Jabra HT800) works great. Comm Manager is real nice. Even showing you the status of SMS and GPRS/EDGE connection. I want to play with it a little more to see if I can control those two or not. Gone from teh Cingular ROM is the ability to click on the Edge status icon in the notification area and tell it to turn on Wifi. But the Turn on Flight Mode still exists under the Cell Strength bar. Signal strength is comperable to the 1.12.10 radio rom I had before the upgrade. And IDK if it is taking longer to load from a reset or not, but before the Phone radio would be up and running just as I was finishing putting in my PIN unlock. But now it is running and connected before I can even start to input it. Just observation, that extra second doesn't mean anything.
Click to expand...
Click to collapse
Where did you get the "Cingulcustomize_No_Emails.cab" file? I have searched everywhere and cannot find it! Help?
Which parts of the BA need replacing to repair my WiFi problem?
My plan is to use the BA dissasembling procedure, and replace parts needed.
I have printed the parts list, and can see that a lot of the minor parts of the BA have some kind of WLAN purpose. Is there a separate board that has all functions of WLAN on it?
I presume if there is only one board it will be expensive?
Moving this to another forum.......... maybe they will know.........
description of problem?
WiFi has always worked for me, until I installed WM5. It would not turn on.
I installed windows mobile 2003SE, anmd when I turn on WiFi the yellow light flashes, indicating it is on, however windows mobile doesn't display the wifi icon, or search for networks. The "eggtimer" icon comes up for a few seconds, and I am then taken back to the today screen.
I can't believe it is a hardware problem, as the light is flashing.
I have now reverted back to WM5
Any ideas?
Thanks,
Tom
hardingt0110 said:
WiFi has always worked for me, until I installed WM5. It would not turn on.
I installed windows mobile 2003SE, anmd when I turn on WiFi the yellow light flashes, indicating it is on, however windows mobile doesn't display the wifi icon, or search for networks. The "eggtimer" icon comes up for a few seconds, and I am then taken back to the today screen.
I can't believe it is a hardware problem, as the light is flashing.
I have now reverted back to WM5
Any ideas?
Thanks,
Tom
Click to expand...
Click to collapse
Exactly same problem is with me
Any possible solution?
Nope, no one has any ideas.......
Success, I have solved my problem! I don't know what I did, but WiFi can now be turned on and off via the comm manager!
If I leave it on when I reset, it stays working after!
Only prob I have is that it won't work with Kasuei Hitchiker.
Yeah bit of a pain!
Yes I've found the issue quite annoying , there was a rom I tried which was out which noted that the wifi would not activate except through Comm Manager but , Helmi's latest upgrade seems to have corrected the issue which merely is a setting change,now more oft than not wifi turns on very good rom .
I've tried it all!! The wifi will not turn on at all. In the settings tab and under connection, the comm manager wifi switch pressed will cause the wait cursor to come up, but after the process it wont turn to on. Can anyone please help me.
how do u know its not on? cant detect wifi?
Is the Wifi antenna icon comes up on the top menu ?
Baronic said:
how do u know its not on? cant detect wifi?
Click to expand...
Click to collapse
Not Sure What you mean.
1. Go to comm manager
2. Hit WiFI and the wait icon starts (should be a quick spin and its on, but the icon goes on for a while).
3. Switch instead of turning green animates back to off.
I have not loaded anything other then SKtools that could change the registry or system in anyway (no other tweaks except Schapp's)
I looked all over this forum and found tricks for other HTC phones, tried one or two, but they are made for other phones. I looked over the GPS and in Google Earth disabled it. I have also done a hard reset. I also get a device.exe error.
Please somebody help us. My diamond's wi-fi doesn't work. I try a lot of tfink. I try a lot of time hard reset. And several times upgrade diffrent roms. Now i use 1.37.401 europa rom. But my diamond's wi-fi still not work.
same here.. any news?...
Juggy said:
same here.. any news?...
Click to expand...
Click to collapse
Did you set your battery for best performance in the wifi configuration? If not, try it and see if it works then
Yes.. the wifi is not working ,... the same for the gps...
Mines the same. Done a soft reset - nothing. Done a hard reset and all seems fine for the mo.
Got my phone from orange.
hard reset u mean erase all and start like new?
with this hard reset.. the same problem... any other option??
No Wify
I have the same problem. No wify. A "device.exe" error appear. Is there any solution?
WLAN Hardware
minlu said:
I have the same problem. No wify. A "device.exe" error appear. Is there any solution?
Click to expand...
Click to collapse
I have the same problem with german htc touch diamond and several roms.
I think the hardware has an error. Bull**** !!!
Has anyone an other idea?
I had this issue with my S710, if you turned the wifi on it would flip to on for a second before going back to off - only happened if I has it hooked up to a pc via usb. Not sure if its the same with the diamond?
I couldn't enable Wifi properly on my last phone despite hard and soft resets. After trying lots of times, I gave up and sent the phone back to Orange. I currently have a Diamond Touch that has no problems enabling, but can't connect to my router using WPA2.
I think I have the solution for wifi / wlan problems on diamond
Over one week i try to start my wifi (100 hardresets, 5 new ROMs) and then i believe it is an hardware error.
Under ...\connection\wifi\ was not the tab "wireless", only the tab "networkcards"
My last try was the solution:
1. In my HTC Kaiser is the same wifi-hardware
2. I export the registrykey "HKEY_LOCAL_MACHINE\Comm\TNETW12511" from the kaiser to a .reg-file
3. I delete this registrykey on the diamond and import the .reg-file from the kaiser
4. Before I can start wifi i make about 5 softresets and try to start
5. But the start was only successful when I make first a connection to the pc with ActiveSync and then a softreset
This is my solution, please answer me when it works for you too
One problem is still there: after an usb connection wifi will not turn on. I must make a softreset but thats no problem for me.
Its the same what "huwwatkins" describe at #13 with the S710
Here is my regfile from kaiser
zmob123 said:
Not Sure What you mean.
1. Go to comm manager
2. Hit WiFI and the wait icon starts (should be a quick spin and its on, but the icon goes on for a while).
3. Switch instead of turning green animates back to off.
I have not loaded anything other then SKtools that could change the registry or system in anyway (no other tweaks except Schapp's)
I looked all over this forum and found tricks for other HTC phones, tried one or two, but they are made for other phones. I looked over the GPS and in Google Earth disabled it. I have also done a hard reset. I also get a device.exe error.
Click to expand...
Click to collapse
I have heard of this... The wifi does not go on but the bluetooth does. I was told it was a bad chip.
same here, called retailer today. told me HTC is working on a fix. will be available in about two weeks. let ya know
Same problem here..
I have the same problem. Tried everything - no luck. Thinking of turning it in for repair - should I flash the original SPL/ROM for warranty reasons or can they tell it's been flashed anyway ?
wifi working fine on mine
i have no problems at all
huwwatkins said:
I had this issue with my S710, if you turned the wifi on it would flip to on for a second before going back to off - only happened if I has it hooked up to a pc via usb. Not sure if its the same with the diamond?
Click to expand...
Click to collapse
Yes my diamond has this also only when plugged with USB.
Grtzzz
Hi all,
I wonder if anyone can resolve/give suggestion for my problem.
Basically i have experience problems connecting via Wi-Fi i.e the after activating wi-fi the phone will scan for available networks and give you the list. I then try to connect to my router (bt home hub which is actually speed touch) it does connect and stays connected for some time then suddenly the connection is dropped and under wifi it says that my access point is unavailable. If i turn wifi off/on again and scan for networks it comes up with "No visible Networks detected" even though there are like 5 access points in my house and i can connect to any of them using my laptop and old nokia e60. If i wait a while it will connect again but will not keep the connection. I have tried at home, work and some public places-every time is the same story.
Things i tried:
Soft reset/hard reset (many times)
Tried disabling phone radio in case3g chip interrupts
I tried with secure networks, open networks, different types of authentication/encryption, different router (more than 10) and every its the same story. I also tried several ROMS and ALL RADIO's available with the same result.
I am currently on Duttys_Diamv2.3 WWE RADIO 1.00.25.08, its a clean flash, nothing else is installed. I also have SPL-1.40Olinex installed (not sure if that could have an impact) The phone is vodafone branded btw (i had the same issue with vodafone rom which is why i decided to try other roms). I wonder if anyone has any thoughts/suggestions and would appreciate any help. Thanks in advance.
The same situation happened to my Diamond. I took it to the local dealer for HTC and after several days, I am told that the main board will need replacement. I am still waiting for it to be repaired as the parts had to be braught in from another country. I was also saud if the phone was less than a month old (which it is not) they would have replaced it with a new phone.
Good luck repairing yours and keep us updated.
omar302 said:
The same situation happened to my Diamond. I took it to the local dealer for HTC and after several days, I am told that the main board will need replacement. I am still waiting for it to be repaired as the parts had to be braught in from another country. I was also saud if the phone was less than a month old (which it is not) they would have replaced it with a new phone.
Good luck repairing yours and keep us updated.
Click to expand...
Click to collapse
Thanks Omar, I was kinda thinking that it may be hardware issue, but I don't anymore, I am trying something else actually as we speak. The only thing I haven't tried before is another hard SPL and I think that's the problem, I installed another version hspl1.34 and it seems more stable now and wifi keep connection, also with another hspl version (it was hspl 1.24) RAM under devise info>hardware showed 128, now it is 192. I will test in intensively and post my results here in case nay one else have the same issue. Hopefully I will not have to send it away for repair. Thanks for your info anyways.
In risk of sounding lame ...
Have ya tried 'Start' / 'Settings' / 'System' 'Wireless LAN'
Under Wireless LAN click 3'rd tab (strømtilstand in Danish - could be power-settings)
On that tab - pull the marker way to the left in order not to minimize the power consumption when tryng to hookup with the WiFi.
I had massive problems to get my local WiFi working at home - until I did this trick.
Best luck, Kindly
Kwasmir said:
In risk of sounding lame ...
Have ya tried 'Start' / 'Settings' / 'System' 'Wireless LAN'
Under Wireless LAN click 3'rd tab (strømtilstand in Danish - could be power-settings)
On that tab - pull the marker way to the left in order not to minimize the power consumption when tryng to hookup with the WiFi.
I had massive problems to get my local WiFi working at home - until I did this trick.
Best luck, Kindly
Click to expand...
Click to collapse
Yes i have thats the first thin you do anyways . I am now more than sure that the issue was with HSPL version 1.34, as soon as i got rid of it (installed hspl 1.24) all is fine.
With my phone, i tired all Hard SPL versions and even went back to stock SPL & Rom 1.37 & 1.93 and it still didn't fix the WIFI issue. it will work for 5-15 minutes then it will not work.
Anyway, I got a replacement phone as apparently they couldn't fix it.
pufeks said:
Hi all,
I wonder if anyone can resolve/give suggestion for my problem.
Basically i have experience problems connecting via Wi-Fi i.e the after activating wi-fi the phone will scan for available networks and give you the list. I then try to connect to my router (bt home hub which is actually speed touch) it does connect and stays connected for some time then suddenly the connection is dropped and under wifi it says that my access point is unavailable. If i turn wifi off/on again and scan for networks it comes up with "No visible Networks detected" even though there are like 5 access points in my house and i can connect to any of them using my laptop and old nokia e60. If i wait a while it will connect again but will not keep the connection. I have tried at home, work and some public places-every time is the same story.
Things i tried:
Soft reset/hard reset (many times)
Tried disabling phone radio in case3g chip interrupts
I tried with secure networks, open networks, different types of authentication/encryption, different router (more than 10) and every its the same story. I also tried several ROMS and ALL RADIO's available with the same result.
I am currently on Duttys_Diamv2.3 WWE RADIO 1.00.25.08, its a clean flash, nothing else is installed. I also have SPL-1.40Olinex installed (not sure if that could have an impact) The phone is vodafone branded btw (i had the same issue with vodafone rom which is why i decided to try other roms). I wonder if anyone has any thoughts/suggestions and would appreciate any help. Thanks in advance.
Click to expand...
Click to collapse
...I have the same problems with you
However, I think the problem may caused by different ROM versions.
My hTC version Diamond initially flashed a Chinese version ROM, and the WiFi connects well, while I changed to Dutty's most updated ROM, this problem comes and I cannot figure out why untill now.
Some friends also suggested to go to the Power Management and change WiFi to "Best Performance", I tried and failed again.
WiFi can open and connect to Routers located in library of my university, nevertheless it cannot open any pages.
I'm also waiting for any person that can solve the problem and then help us figure out why....
thanks in advance!
I got the same problem as most of the people have. and i think "Fail to turn on wifi" is a very common among guyz who got HTC TD.
I dont know what should be done, i almost tried every thing. actually my phone was locked to 3 mobile Sweden and i unlocked it but my wifi was'nt working before unlocking too but i did'nt gave attention to it. Now i noticed it.. is that any one know how to lock it again soo that i can send my mobile for repairs or, any one know what should i do.
I would recommend upgrading your radio and your rom.
Ive been rocking the setup in my sig for some weeks now and its been flawless, stable and fast.
which rom and radio you are using. can you please help me in this matter.
and i think its not a hardware problem because its showing that hardware is connected to my device as its shown in the screen shoot
Hi,
Im using AlphaZero V7 NLD,
Im have 1 wifi point in my house, downstairs.
even when im on the attic i have 80% signal strengt.
My router is a draytek 2820G router.
Wifi for me is very good. .. correctly, AZTOR V7 NLD is very good for me.
im on t-mobile network.
Radio Radio v1.00.25.05 , Radio v1.00.25.08, Radio v1.00.25.16, where all good,
now testing Radio v1.08.25.20, HDSPA signal is bit weaker atm.
my best radia atm i think, v1.00.25.08.
im betting, that the starter of this toppic, who has 5 access points in his house all have the same SSID. This is not the way.
Or make 1 big AP aera, bij connecting the AP's to each other.
of try to set every AP its own SSID, and its own Channel.
Louis
WIFI problem in HTC Diamond.........
I am trying connecting to my home wireless network. It finds the network but unable to connect to it. Any help please? Has anyone managed to get it connected to any Wifi? I ahve already set the power management to "best performace...no succes.......
(My laptop and O2 stealth does get connected to the same network and it an open wifi connection)...........PLZ Help.....
pranavsethi said:
I am trying connecting to my home wireless network. It finds the network but unable to connect to it. Any help please? Has anyone managed to get it connected to any Wifi? I ahve already set the power management to "best performace...no succes.......
(My laptop and O2 stealth does get connected to the same network and it an open wifi connection)...........PLZ Help.....
Click to expand...
Click to collapse
i am also having this problem, it can find the network, and can spend a minute or 2 trying to connect, and nothing happens. you posted this in february, did you find an answer?
Wifi & Bluetooth not detected by HTC Diamond
Someone pl help. My HTC Diamond is not detecting bluetooth devices neither is detecting wifi. It was earlier doing so and working fine however I believe after installing tweak TD & t3d config it has stopped working. I have installed new ROM also but to no avail. Can someone pl help!!!!!!!!
Wintermoonlight said:
i am also having this problem, it can find the network, and can spend a minute or 2 trying to connect, and nothing happens. you posted this in february, did you find an answer?
Click to expand...
Click to collapse
i also have the same problem. it detects a wifi (my router at home Aztech brand), then trying to connect to it, and then it always showed the wifi as "unavailable". i put my phone 2 mm distance from the antenna of my router it also won't connect. i have change dozens of roms, win 6.1, 6.5, 6.5.1, different cook, MTTY, all with no success.
i've looked for internet and google for answers, i seen quite a lot of forum has described this issue, but with no solution. most of the ppl suggest in various forums to pull the wireless slider to "Best Performance", ofcourse i have done that, but is just the same result.
i'm still trying searching for a solution for this, i hope is not a hardware issue because my warranty has already ended. i'm currently using Gen Y R4.1B rom
pufeks said:
Yes i have thats the first thin you do anyways . I am now more than sure that the issue was with HSPL version 1.34, as soon as i got rid of it (installed hspl 1.24) all is fine.
Click to expand...
Click to collapse
Ok consider now wifi will work by re-flashing the spl.
But what is the relation between spl (os/winmo loader) with wifi?
another dang unsolved diamond wifi?
bravo.
same problem with wifi on diamond2
With Original stock WM6.1 i was unable to connect at all, after flashed official WM6.5 upgrade everything worked fine. However i decided to put cooked rom because of battery life and perfomance issues. Dutty HG6 for Topaz seems to be with glitchy radio, it works sometimes, very rare, and i'm still not up to the pattern when does it happen and why. Pretty sure it's not a hardware problem - so everybody relax, we will find the solution.
which rom and radio you are using. can you please help me in this matter.
and i think its not a hardware problem because its showing that hardware is connected to my device as its shown in the screen shoot
wjenya said:
With Original stock WM6.1 i was unable to connect at all, after flashed official WM6.5 upgrade everything worked fine. However i decided to put cooked rom because of battery life and perfomance issues. Dutty HG6 for Topaz seems to be with glitchy radio, it works sometimes, very rare, and i'm still not up to the pattern when does it happen and why. Pretty sure it's not a hardware problem - so everybody relax, we will find the solution.
Click to expand...
Click to collapse
nope, i also put Gen.Y WM6.5 then the problem still arise.
i'll wait any solution until my diamond is totally wrecked
I'm having a problem with my Kaiser, WiFi does not turn on. And I don't mean I can't connect, I mean it doesn't turn on. Searching on the forum I found this threads:
http://forum.xda-developers.com/showthread.php?t=420868&highlight=turn+wifi (This one even has a video showing what happens when trying to turn WiFi on)
And
http://forum.xda-developers.com/showthread.php?t=381370&highlight=turn+wifi
But there is no solution for the problem on any of them.
I've already flashed tons of differents SPLs, radios and ROMs, soft/hard reseted and even did a "task 2a" (wich whiped everything, bricking my Kaiser. Thanks jockyw2001 for FrankenKaiser!). None of this made my WiFi work.
On the Hermes forum I've found this thread:
http://forum.xda-developers.com/showthread.php?t=322225
Could this be what happened to my Kaiser? Can anyone help me fix it?
Thanks!
Check out this thread.
http://forum.xda-developers.com/showthread.php?t=511001
ChumleyEX said:
Check out this thread.
http://forum.xda-developers.com/showthread.php?t=511001
Click to expand...
Click to collapse
Thank you, but that guy's WiFi turns on and doesn't find any networks. My WiFi does not turn on. On the other hand, if your pourpose was to tell me that my WiFi is "broken" I would like to know what is broken so I can fix it. Thanks!
The number 3 capacitor is fried on the wifi card.
Maybe my mindset is too simple, but I always think that if (on a device like this) you reload fresh software over and over that is known to work, and the device doesn't work, then the device is broken. There are no dip switchs or knobs to turn, no drivers to reload (because you just reloaded them by reinstalling the ROM). Maybe you can reseat the device. Take a look at the disassemble guide and see.
ChumleyEX said:
The number 3 capacitor is fried on the wifi card. [...] Maybe you can reseat the device. Take a look at the disassemble guide and see.
Click to expand...
Click to collapse
Will do, thanks for the advice!
What about this thread? http://forum.xda-developers.com/showthread.php?t=322225
Don't you think it's worth a try?
I would suggest you ask Drummer10630 or someone like Chainfire, if that is a bad idea. It looks like it could work with the right files.
I wouldn't want to suggest you zap your phone more then it's already zapped.
ChumleyEX said:
The number 3 capacitor is fried on the wifi card.
Maybe my mindset is too simple, but I always think that if (on a device like this) you reload fresh software over and over that is known to work, and the device doesn't work, then the device is broken. There are no dip switchs or knobs to turn, no drivers to reload (because you just reloaded them by reinstalling the ROM). Maybe you can reseat the device. Take a look at the disassemble guide and see.
Click to expand...
Click to collapse
Here you go at it again.
TILT doesn't have a WiFi card or WiFi adapter as you keep on calling it.
Here is an advice for you: if you don't know the answer, don't answer the question.
hth
Oh then what should I call the wireless thing? Does it work on magic?
If you're so freakn smart why isn't your wireless working?
I got same problem which cannot turn on WIFI, almost seach all the solution about this problem and send my device to repair to find the hardware problem , but still cannot work, i give up already. fortunately, I know how to make it work sometime, there has some experience about it,hope it can help you.
. turn on the SYNC connectoin option Allow wireless connection
. pull up battery for 30 second.
. hardrest after refesh new rom.
but those for my device only can work for once, after device sleep cannot turn on again, or freezen and after soft rest, wifi cant turn on again.