ok here is what i did....i installed aku 3.3 and it was fine for coupke of days and now i changed the omap speed to 290 mhz... when i did a soft reset...what happened the screen comes on for "loading windows" it loads then i see the "start" screen and then all of a sudden everything freezes and i cant do anything... i do a soft reset again and same problem.....guys!!!!!!! is there anyway to do a hard reset without turning on the phone or something... when my phone goes to themain screen when i turn on the phone..it freezes instantly and i cant push any buttons... please help
ok hold the comms button and the mic rec button and then power on the device and press the gree button when prompted this will do a hard wipe
you overclocked so hard that it got frozen upon start up. I usually just take out the battery and wait a little bit and everything is fine. if not I will do another soft reset after removing the battery
that worked!! thats a lot buddy...
here is what i did....i holded the comm manager button on the left and the voice command button on the right..... i kept on holding and then i did a soft reset...while holding the 2 buttons after i do a soft reset... i press thenavigation pad "up"...while holding those 2 buttons..then it ask me to press "send"...i pushed the green button
pakirebel19 said:
ok here is what i did....i installed aku 3.3 and it was fine for coupke of days and now i changed the omap speed to 290 mhz... when i did a soft reset...what happened the screen comes on for "loading windows" it loads then i see the "start" screen and then all of a sudden everything freezes and i cant do anything... i do a soft reset again and same problem.....guys!!!!!!! is there anyway to do a hard reset without turning on the phone or something... when my phone goes to themain screen when i turn on the phone..it freezes instantly and i cant push any buttons... please help
Click to expand...
Click to collapse
260 is the highest stable setting that I have seen mentioned anywhere on these forums. People report lockups and loss of stability if they go higher. Of course there is variability from device to device and you may have to go a little lower or might be able to go higher. You will have to experiment with what works the best with your device. As the others have said try resetting and lowering this value. Perhaps even use BatteryStatus to set the clock speed based on the running application.
I use battery status and works fine and stable at 273MHz.
I overclocked it too above 280-290 ... but worse case, it froze and a simple soft reset did the trick. Mabe he enabled overclocking upon boot... That's not a bright thing to do
With BatteryStatus my Wizard works fine on 299Mhz (WM5 and WM6).
clocked to 312 permanently (after soft reset etc)
using molski rom it's the fastest (of all that i've tried) and perfectly stable.
B
Related
Perhaps, all of my expert-friends here can diagnose why my hima often freeze everytime I perform a soft-reset here.
It just freezed, stating Windows Mobile 6 Tofclock. And it never moves.So, I always perform hard-reset afterwards
Anybody can tell me the solution to this problem?
I also got the same problems. I charge my PPC and after sometime (5min-1h) it would run again, but I really hate that
Try to flash your rom again
Or start checking installed software
mine has jsut started doing this too
it's been fine for weeks, but this morning it just wouldnt boot. It hung on the alarm this morning so i couldnt cancel it, soft reset and npow wont reboot. hard-reset....same thing
I noticed that WM6 Hima's can behave very weird when power is very low, including:
-refusing to load battery
-refusing soft reset
-refusing hard reset
-refusing to listen to any hardware button or touch screen
-horizontal lines in screen
-very dim backlight
-not refreshing screen information
That last symptom can be very confusing when you load the battery, battery meter clearly shows 100%, you switch off while some battery draining software is still active (minimized), you switch back on, still see battery near 100% but some or all other symptoms are taking place.
So:
-be sure to have low battery reminder active
-be sure to use a taskmanager and exit background programs
-keep backups
-kee backup
-ke backu
-k bac
Had the same problem with Fresh AKU WM6 Rom.
Flashed my Qtek with another ROM, never had the problem again
The most funny:
If I couldn't soft reset, I have to hard reset.
If I perform a full restore with SPB Backup, and then soft reset, new freeze! So I couldn't restore datas after hard reset
That's why I prefer SPB clone, not meant to be a backup program but a way to fast create a bunch of identical devices, but it's actually the best backup I know. Syncing after restoring a clone always gives an error message once, but I never lost a bit of data. And all reminders between the moment of cloning and the moment of restoring the clone have to be dismissed.
Maggy said:
I noticed that WM6 Hima's can behave very weird when power is very low, including:
-refusing to load battery
-refusing soft reset
-refusing hard reset
-refusing to listen to any hardware button or touch screen
-horizontal lines in screen
-very dim backlight
-not refreshing screen information
That last symptom can be very confusing when you load the battery, battery meter clearly shows 100%, you switch off while some battery draining software is still active (minimized), you switch back on, still see battery near 100% but some or all other symptoms are taking place.
So:
-be sure to have low battery reminder active
-be sure to use a taskmanager and exit background programs
-keep backups
-kee backup
-ke backu
-k bac
Click to expand...
Click to collapse
May be you are right, when the power is very low the behavior of WM6 is very weird. This is a bug ? Any suggestion to overcome this problem?
i figured it might be a software conflict or something that was breaking it so JUST before i re-installed i had a brainwave and tried this :
Hard reset your pda.
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> NO
When done, press DPad and wait until OS starts.
it worked.
I've had a wing for the past 2 months. Over the past 2 weeks, the phone has been acting wierd. Occasionally, it will be working fine and I'll click the power button to turn off the screen (like I do all the time). Then when I go to turn on the phone, the screen stays black and it locks up and is unresponsive to any keys or sliding out the keyboard and I need to pull the battery. It's not the battery because it is fully charged.
The only 'hack' i've done to it since i've had is the pagepool thing. Any suggestions? I'm tempted to reset it/format it to remove any 'hacks' but not sure how to do so. I'm not sure the reset with the 1234 command will remove the pagepool hack
First of all, why are you pulling the battery? All you have to do to reset the phone is a "soft reset" ... which means putting the stylus into the little hole on the left side of the phone under the volume slider.
You should probably try to hard reset it. (hold in both soft keys while soft resetting) and yes, You'll have to set the pagepool back up.
Do keep in mind this will delete everything off your phone, so be sure to backup any important files before doing so (contacts, pictures..etc..)
I've had this happen to me a few times. I can say this though, when I flashed a new rom onto it it stopped.
If you don't want to flash, try looking in settings>system>key lock and set it to "Lock all buttons except Power button" or possible looking into some auto-locking programs, like S2U2 by A_C.
Good luck
phreke
heres a question, what did you set the pagepool to? If you set it to like 32 bajillion or 0, it won't work. also, some of the older pagepool changers don't work with the wm6.1 roms
I just got my Sprint Diamond last night and sure enough I installed a bunch of programs and tweaks on it.
Now when the phone starts up, it just keeps vibrating like crazy and the screen and hard buttons are unresponsive for the most part. The ONLY thing that works on the screen is the Quick Menu on the top right. Tapping the screen anywhere else doesn't do anything. The ONLY hardware keys that work are the D-Pad keys, nothing else works. Also, i get an error message on startup that says "gsen cannot connect to G-Sensor".
Here's what I did before my last soft reset:
1. Installed gsen (the sensor app). I don't think this messed with anything though.
2. Changed the screen pressure value on the "Advanced Configuration Tool" program v3.2 down from the default of 42 to 34. This didn't seem to make any difference so I wanted to see how this would change the sensitivity. I set it all the way down to 2. This is what I think broke it.. I'm guessing the low value means more pressure is required to press.
I've tried a hard reset (vol-down + enter + reset with stylus) and it doesn't do anything at all.. I've tried this many times but to no avail
Does anyone have any ideas about what I could do?
Thanks in advance.
Figured it out, it was definitely the pressure sensitivity. I used CERegEditor to connect to the registry from my computer and changed the value back and restarted the phone and all was well.
Just wanted to post the solution in case this happened to someone else.
for hard reset ( if u need it...or if u will need it)
1. Pres Vol down + d-pad (center button) + soft reset button....then release soft reset button.....and wait till couple of seconds
Hi,
I wonder if I'm the only one having this issue...
sometimes, after a call, the phone freezes and I have to press the Home key to get the TF3D screen back.
But after that, I can't make a new call... nothing happens when I press the "Call" button or when I try to launch the dialer by pressing on the "Phone" soft button.
I try to launch the FdcSoft TaskMgr (wm2005_3.1) in order to see if a process was stuck, it usually loads fast but in this case, it stops loading and nothing was displayed... (I'm still able to see the TF3D background instead of TaskMgr).
Only way to recover from it, is to SR the device...
I switch off the device each nights, I would expect more stability, it's not like I'm running it for more than 2 weeks...
This issue always occurs (when it does) after a call or when I press the hard key "End call".
Oh, funny thing... By 3 times, I was also unable to end a call, the call was still running and I had to SR the device to end the call... very nice !
Anyone with this issue or with an idea ?
It's the only thing that drives me crazy with this phone :|
Rom : 1.93
radio : BS14 currently, but it was the same with previous radios.
is there anybody with a little clue for me ?
Please
Me too.
Panosha: 1.93.405.1 WWE Shine On 2.4 Full
Radio: 1.03.25.18
After calls... Freezes 80% or more. I don't know if maybe it is 100% of the time when the other end hangs up first. (I don't get it with Voicemail!)
I also get freezes some other times. I don't think it is memory related, (before someone suggests it.) Also Please don't tell me to Hard Reset. I have Hard resetted to my heart's content, also directly after every Rom Update (to get GPS working)
try soft reset......i also got that problem....i do a soft reset,works fine...
cheers!?!!!
Hi
It's not the first time I flash my TytnII, but this time, I get worry about my phone...
I've tried to put the kaiser_wwe_shifu_v3.0 rom's.
According to doc, I've upgraded Radio and Hard SPL.
Radio is 1.70.19.09
Hard SPL is 3.29.
The upgrade of ROM was OK, but some stranges things appened therefore. The first boot, OK the device is configuring itself, and rebooting.
After the first reboot, the device is still "fresh installed"! So here we go another time to pre-configure it...(time, touch screen...)
After, it seems to be OK, but in fact, I see there's no more memory to completely startup the phone. Because the phone starts, but finally, a program (don't remember which one) says that it cannot start because lack of memory...)
I reboot, and since, me phone doesn't boot at all....
It display the startup page with radio , hard SPL infos, but no more, it seems to be completly block on these steps.
What could I do?
Thanks a lot
Have you tried to flash another ROM?
You can try this bij holding camera button while booting, you should see the tri-color screen. Connect it to your PC and try to flash again or another (maybe stock-rom?) ROM.
Good luck
No funny multi color screeen appears when pressing camera button while booting...
Can't connect a cd reader on it, and erase flash
thanks
Do a hard reset and see if that works, hard reset is hold down left and right softkeys and and hold in reset button with stylus until you get to a screen about resetting the phone, remember to back up any data on phone memory cos you will lose this after a hard reset
I want to second this problem.
After flashing the Radio to "KAIS_RADIO_ONLY_1.71.09.01" and installing PDA corners newest ROM, everything worked fine. The only bug was that when I wanted to turn off the device by holding the power button, after choosing the turn-off option, it just restarted.
Now the phone doesn't start at all. Seems as if there is no power from the battery, while there was enough charge in it. When I connect it to the power plug, the charging/power led turns almost red, never saw that before.
This is not my first ROM-update, but this is the first time I've encountered this problem.
I tried hard and soft resets, removed the battery, tried to connect it to the pc, nothing worked.
Any ideas?
Thanks.
Press and hold the camera and the power/ on buttons. While ho[ding both buttons, do a soft reset. Once in bootloader ( tri color ) flash your original stock rom.
What I already tried:
- hard and soft resets
- removed the battery
- tried to connect it to the pc
- connected in the power plug, nothing worked.
- tried the power button+camera+soft reset
I download the the same Rom....I I have the same problem.... I Reset with Pressing Camera and Power method....it went to the Hardspl screen and I load a new ROM...its working fine now.