Hello Everybody,
My Qtek 9100, after a upgrading process, don't recognise Usb connection.
The Qtek works normally but only my Usb Connection don't work to charge the battery and to connect to the Pc...
Could you help me, please?
Thanks and best regards.
Does it not work with your wall carger either? What version of active sync are you using what's your device info? (rom, ipl/spl, etc....)
there is a reg tweak. do a search for usb charging registry tweak
Thanks to everybody for the answers...
My qtek don't work neither with wall charger..
I charge my battery with a home-made cut Usb cable connecting directly the battery.
I Use ActiveSync 4.2.
IPL 1.03
SPL 1.03.0000
OS 2.18.9.1.
Yesterday I searched in regisrty tweak usb charging...
HKLM\Drivers\BuiltIn\usbfndrv\EnableUsbCharging = 1 (enable charge)
Maybe with the Upgrade i have destroyed the Wizard !?!?!
I don't ever know what I can do!!
Bye
If you haven't fixed the problem already, try switching it off , pull out your battery, insert the charger and after insert the battery
See if it starts charging
good luck
By the way, what ROM you currently have installed ?
sikario said:
Thanks to everybody for the answers...
My qtek don't work neither with wall charger..
I charge my battery with a home-made cut Usb cable connecting directly the battery.
I Use ActiveSync 4.2.
IPL 1.03
SPL 1.03.0000
OS 2.18.9.1.
Yesterday I searched in regisrty tweak usb charging...
HKLM\Drivers\BuiltIn\usbfndrv\EnableUsbCharging = 1 (enable charge)
Maybe with the Upgrade i have destroyed the Wizard !?!?!
I don't ever know what I can do!!
Bye
Click to expand...
Click to collapse
yeah
It looks like You did't CID unlock before upgrade or You upgraded with G4 rom (without IPL/SPL). You CAN'T HAVE OS 2.xx on IPL/SPL 1.xx
Now You have to back to old ROM, CID unlock him and upgrade with G3 ROM (with IPL/SPL).
Or maybe (corect me if I'm wrong), if You are sure CID is unlocked just upgrade with G3 ROM
maymaymay said:
yeah
It looks like You did't CID unlock before upgrade or You upgraded with G4 rom (without IPL/SPL). You CAN'T HAVE OS 2.xx on IPL/SPL 1.xx
Now You have to back to old ROM, CID unlock him and upgrade with G3 ROM (with IPL/SPL).
Or maybe (corect me if I'm wrong), if You are sure CID is unlocked just upgrade with G3 ROM
Click to expand...
Click to collapse
I think that i had CID UNLOCK... my Rom was 1.8.xx German and now I have Upgraded it in Italian language.
I would to back to my old rom, but without USB Connection, it's impossible!
Maybe the Rom that I've installed is too much new for my device....
and Maybe only the assistance can be solved the problem...
I give up!
Bye
sikario said:
I think that i had CID UNLOCK... my Rom was 1.8.xx German and now I have Upgraded it in Italian language.
I would to back to my old rom, but without USB Connection, it's impossible!
Maybe the Rom that I've installed is too much new for my device....
and Maybe only the assistance can be solved the problem...
I give up!
Bye
Click to expand...
Click to collapse
Just because it is not charging or connecting to Activesync does not mean the USB connection isn't working. While you are on the bootloader screen (red, green, blue screen) plug in your USB cable. If the letters USB appear in the corner you have an active USB connection. From there flash your phone with a 2.x carrier rom (preferably from your own carrier). Then follow the instructions in the unlocking Sticky thread (don't skip any steps no matter how wierd or out of place they might sound--they are all in there for very specific reasons and virtually everyone that follows them don't have issues) Then feel free to upgrade to whichever compatible rom you want. Just be aware that when flashing, a mistake can ruin your phone. Make sure you are prepared for this to happen when considering whether or not you really NEED to flash your device.
sikario said:
I think that i had CID UNLOCK... my Rom was 1.8.xx German and now I have Upgraded it in Italian language.
I would to back to my old rom, but without USB Connection, it's impossible!
Maybe the Rom that I've installed is too much new for my device....
and Maybe only the assistance can be solved the problem...
I give up!
Bye
Click to expand...
Click to collapse
NO.
Now You have to enter the bootloader by keeping camera button and soft reset, then conect USB and You can upgrade.
THANKS to everybody for the suggestions!!
I will try to enter the bootloader in my device (camera button and soft Reset)..
and i read well the "unlocking Sticky thread"....
I hope to do all the things in good way....
......
Thanks........
I enter Bootloader by keeping "Camera button" and "soft reset" with the little pen... but don't appear the Bootloader Screen...
Is it normal?
sikario said:
I enter Bootloader by keeping "Camera button" and "soft reset" with the little pen... but don't appear the Bootloader Screen...
Is it normal?
Click to expand...
Click to collapse
Try turning the phone completely off (hold down the power button until is shuts down)
Then press and hold both the Voice command key and the camera key.
While they are both held down press and release the power button.
Might work with the soft reset button but I always use the main power button.
Zzan said:
Try turning the phone completely off (hold down the power button until is shuts down)
Then press and hold both the Voice command key and the camera key.
While they are both held down press and release the power button.
Might work with the soft reset button but I always use the main power button.
Click to expand...
Click to collapse
OK Zan!
I held both keys and in the same time "on/off Switch"...
but my device only light on the orange led in the right above...
I am trying to do and do.....
Thanks for now!
sikario said:
OK Zan!
I held both keys and in the same time "on/off Switch"...
but my device only light on the orange led in the right above...
I am trying to do and do.....
Thanks for now!
Click to expand...
Click to collapse
Try to keep camera button, then press SR keeping camera button untill bootloader shows.
ok...
with the phone off, hold camera button and key button... after press and release on/off button...
Bootloader is charged!!
tomorrow i will try to re-flash my device...
maybe i will ask you other things....
Bye
Related
MDA has a charge sign at the bottom but its not even plugged in at the USB, the charge is also "unknown." When I updated the rom it didn't include the GSM ROM...
Now it won't recognize with active sync on the computer, so I can't just change the rom. any other way to get to USB MODE or use a SD card to update the T Mobile ROM. The CID is Unlocked for upgrades maybe there will be hope...
oh no... what can I do?
SQL Master
aoakes said:
MDA has a charge sign at the bottom but its not even plugged in at the USB, the charge is also "unknown." When I updated the rom it didn't include the GSM ROM...
Now it won't recognize with active sync on the computer, so I can't just change the rom. any other way to get to USB MODE or use a SD card to update the T Mobile ROM. The CID is Unlocked for upgrades maybe there will be hope...
oh no... what can I do?
SQL Master
Click to expand...
Click to collapse
Same here too...
Need some help
Same happened to me. To fix it:
.- If battery is drained, organize first a battery that has at least 50% power left. Best is fully-charged battery.
.- Switch your phone into so-called bootloader mode (press and hold "Camera" button while powering your phone or reseting it with stylus).
.- In bootloader mode phone can establish a connection with PC via USB. Re-flash then with a ROM image. I suggest to use CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE if possible
I suspect that the described problem might be caused by not successfully finalized CID unlock before flashing. Hope that above guidelines are helpful.
Sincerely
Rafal (Poland)
rafal23 said:
Same happened to me. To fix it:
.- If battery is drained, organize first a battery that has at least 50% power left. Best is fully-charged battery.
.- Switch your phone into so-called bootloader mode (press and hold "Camera" button while powering your phone or reseting it with stylus).
.- In bootloader mode phone can establish a connection with PC via USB. Re-flash then with a ROM image. I suggest to use CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE if possible
I suspect that the described problem might be caused by not successfully finalized CID unlock before flashing. Hope that above guidelines are helpful.
Sincerely
Rafal (Poland)
Click to expand...
Click to collapse
The above procedure works perfectly.. I had the same issue, in my case sometimes the phone doesn't power on, or even charge!!. The case is simple. Mostly just CID unlocking the phone isn't all. The IPL/SPL figures remain at 1.xx which is not compatible with the 2.26 upgrades currently available. Basically it is always better to upgrade the rom using a provider upgrade, which would upgrade all i.e. both IPL/SPL and OS. in my case starting up was an issue so i go straight into bootloader mode by holding down the camera button whilst switching the device on. Connect the device to the computer. and flash as normal.
Urgent helps needed!
So i bricked my Cingular 8125!
I just wanted to upgrade my ROM to the newest AKU 3.2 from Faria.
I did ungrade and errors arised as i described above.
I was told that the fone hadn't been CID unlocked.
I did as what described in lowikiz
-downgrade the rom,
-run enablerapi.cab on my device
-run lowikiz 0.2b
-choose CID unlock
Restarted the fone, what i saw was:
IPL 1.01
SPL 2.25
GSM 2.47.11
OS 3.0.0
There're only two things fulfill me,that's GSM and the OS.I wanted the
IPL and SPL should be 2.26 or later version.
What i did then :
-Downgrade again (hoping that i forgot to SIM unlock)
-run enablerapi on my device
-run lowikiz 0.2b
-choose unlock
And when the fone restart.
What i saw was:
IPL 1.01
SPL 1.01
GSM 1.x.x
OS 1.05.x
when the installation completed, i upgraded the ROM again to AKU3.2
everything went smoothly until it finished.The fone restarted and what i saw was:
IPL 1.01
SPL 1.01
<blank, no GSM version, couldnt believe that>
OS 3.0.0.0
the device kept running until the installation completed.
It restarted again and stopped running.What i can see now is just
nice background and blinking (waited for nearly 15 mins but no futher responses)
IPL 1.01
SPL 1.01
OS 3.0.0.0
It couldn't get further.
I think i bricked my Cingular 8125.
So could you helpers, experienced users help me with that?
Can i fix it?Or can HTC fix it?
Thank you very much!
mod edit;
the title has been changed as you did not have a bricked phone...if you ever brick you phone belive me,,,u cant restore it at home.
regards
faria
It's not bricked. As long as you can go into bootloader mode, and flash it with Cingular clean ROM you should be fine..
Have you ever read the note from faria? He said NOT to upgrade to AKU 3.2 without IPL/SPL version 2.xx.
You can try to take out you're SIM card, go to the boot screen by pushing the cam button and the on button and flash it again with te original ROM.
Good luck
Sorry for my bad English
or you can try it this way: link
just go into bootloader (camera button + soft reset) and flash that 1.5 ROM, which is able to downgrade.
and then
!Do !NOT! install any 2.x ROM (like farias ) for the 1.x bootloader (ipl/spl)!
before it you could flash any official 2.x ROM ;-)
I'm pretty sure that this was resolved in another thread and not updated here...
Dr Puttingham said:
I'm pretty sure that this was resolved in another thread and not updated here...
Click to expand...
Click to collapse
You are correct.
--M
(granted there may be a lot of pages to read through to get to the information...but a solution was posted.)
Yes I was pretty sure I saw it resolved in another thread, might have even helped...
Ahh, the joys of posting across threads... makes me feel oh so nice!
Thanks
Thank you friends for all those things.
Things seem to get worse, I couldn't even turn the fone on.I had full charge of batt. before upgrading .After that "accident", i left the fone alone for one night, when i woke up in the morning, tried to turn on the fone but i failed.Tried to enter bootloader mode but failed.The fone now becomes a brick.
-Do you friends know how to revive my fone?
-Do you know where can i have it revived?
Thanks for all!
Leave the battery out for few days, then try again after full charge in BL mode.
TIA
BL Mode????
almozaffar said:
Leave the battery out for few days, then try again after full charge in BL mode.
TIA
Click to expand...
Click to collapse
------------------Thank you very much almozaffar and friends!But how can i full charge the batt. in BL mode?I just have the wall charger as included in the box, a USB cable.What i need in BL mode?
I find no red LED(indicating that the fone's being charge)when i connect the fone with my wall charger as well as with the USB cable.I realise that the batt. gets hot but i'm not sure if it's charged.
Best regards
Someone just told me to remove the batt. for about 2,3 days then recharge, i'm not sure if that works but i'll try.Thank you!
Same problem here!
I have a Cingular 8125, I tried to update it to MDA with IPL/SPL 2.26. I was successfully flashed it. After it turn on, everything work fine, so I turned it off, so that I can inside my sim card. After I inside my simcard, my phone is now can never turn on again. I tried and tried again, there was no used. I plug in the power to the phone, there is no power. When I unplug the power, I see a flash from the screen, or after I remove the battery I see a flash from the screen. I have no idea what it is doing, but i can't turn the power back on. Can some please please help me!
Thanks,
Bricked fone huh? No way!!!
After researching the Wizard, i know how to revive it and do not have to spend a cent!Anyone interested?Please PM me!I'll post later when i have time the whole procedure.
@unknown84: I send u file on how to revive your fone.
How to revive your 8125.
Friends,
First remove your main battery, then plug and unplug the wall charger connecting to your fone, if the RED LED and your Fone screen flash then you can revive your fone(at least it works with my fone,wish you good luck!)
Read these lines carefully before you proceed to the procudure.That really works with my phone(i'm not sure if it works with your fone but i wish you good luck)
*Preparation:
1.Charge the main batt. for 2 hours long.
2.Remove your main batt., charge without the main batt. for 1 minute.
3.Plug and unplug the wall charger for at least 3 times ( main batt. removed) (you'll find that your fone keep flashing, both LED and your Fone screen, by doing this i hope it'll help with waking up the backup batt.)
4.Download the official Cingular 8125 ROM version 2.25(you can find it everywhere)
-Three ways to enter bootloader mode:
a.Hold firmly CAM + Power until Bootloader Mode appears
b.Hold firmly Voice Dial,Rec Button + Power until Bootloader Mode appears
c.Hold firmly CAM + Voice Rec + Power ........
*Procedures to followremember to remove your main batt. before doing hereafter)
1. Hold simultaneously 3 buttons : the CAMERA button, The Voice Recording Button, and the Power button.(or follow one of three ways to enter bootloader mode listed above)
If this doesnt work, do that again by holding those buttons, plug and unplug the wall charger and still keep holding those buttons
(as PLUG and UNPLUG the wall charger, you'll see the Red LED and the screen FLASH, i guess it's the way to WAKE our backup batt UP)
2. Hold those buttons will start the bootloader mode.
3.When your fone's already in the bootloader mode, put the main batt. in
(I'm sure u know what u'll do next if u can start the bootloader mode!!)
4.Unplug your wall charger
5.Plug in the USB cabble connecting to your PC.
6. Start flashing with your 2.25 ROM.
Note: When your fone's in its bootloader mode you can find out if u have a G3 or G4 chipset easily by
looking up at its IPL and SPL. G3 comes with x.xx( ex: 2.25)in both IPL and SPL.G4 comes with x.xx.001 in both IPL and SPL.
If u have a G3 chipset, do as i told u above. If u have a G4 chipset, just download the official ROM for your G4.
Good luck and don't flash again without reading carefully!
battery trick
Congras.
So the Battery trick works. I learned this trick even from motorola phone and apllied it to my 8125.
Now thank you for the newtrick you just detaled us with, appreciate itvery much.
TIA
almozaffar said:
Congras.
So the Battery trick works. I learned this trick even from motorola phone and apllied it to my 8125.
Now thank you for the newtrick you just detaled us with, appreciate itvery much.
TIA
Click to expand...
Click to collapse
=========
You're welcome almozaffar, you did help me with this to find a solution for our users' troubles here.
Thank you too :-D
I have brick
Could you please write for how long did you repeat the steps that you described, before getting BL screen.
THX
Still bricked
It certainly doesn’t work for me. Screen & led flash when taking out usb plug without battery, but that all.
simmilar problem
My HTC Wizard is having simmilar problems but even following these directions, I still cannot revive it.
I know my battery is almost full because when it died it was full. I don't know anyone else with a Wizard so I can't charge it, and this may be where the problem lies: Weather or not the battery is in my phone, whenever I connect wall power, it displays the message "Press send to restore...." and will not charge
When I plug/unplug the wall power with the battery removed, my screen does flash along with the red LED, but only once when I pull the power. Following the directions I have removed the battery and I'm plugging in the wall power jack in an attempt to enter bootloader screen. But just like every time, about three to four seconds after I plug it into the wall, the phone posts the "Press Send to restore factory, blah, blah blah". I don't know if this is part of the problem but it might be.
I've tried almost everything i found on forums, and what I can think of but still to no avail. I can't get my Wizard to enter bootloader mode. I've also tried every method to enter bootloader mode that I could find :/
any suggestions?
Since I upgraded to "PDAMobiz_Wizard_Crossbow_AKU3.3_v.3311_G3_onl y"
my HTC will not let me upgrade to anything anymore.. once I run the "ROMUpdateUtility_Wizard_NoID.exe" utility for any version of software including the original PDAmobiz file..
the phone will shutdown when it is supposed to but will not restart.
Now if I hit the reset button it will reboot just fine, it will not go to the colored bars but will boot like nothing ever happened.
it seems like it is freezing from automatically restarting.
any ideas?
also.. any ideas why from this version of crossbow I am losing a LOT of incoming calls?
IPL. 2.26
SPL 2.26
GSM 02.47.11
OS 3.0.0.0
G3
Thank you guys..
Bootloader mode
Try entering Bootloader mode manually first, then running the upgrade. And from what I have read about the 2.47 radio ROM, that is the culprit of your missed calls.
TomInMB said:
Try entering Bootloader mode manually first, then running the upgrade. And from what I have read about the 2.47 radio ROM, that is the culprit of your missed calls.
Click to expand...
Click to collapse
How do I do that?
Bootloader mode
Power off the phone. Then, while holding down the camera button, power it back on. You should then get the 3 color bars. Connect your USB cable and you should then see "USB" on your phone. Then run the upgrade on your PC as you normally do.
I find when all other upgrade utilities fail the Italian NOID one comes up trumps.
neonkoala said:
I find when all other upgrade utilities fail the Italian NOID one comes up trumps.
Click to expand...
Click to collapse
GUYS the camera button did the trick..
when I was trying it earlier it was not working, the trick is that I had to actually shut it down with the off button. (I was just pulling out the battery)
Either way it did it ..
Super thanks guys
I dont know what to do... Yesterday i flashed my wizard to wm6 mb rom, everything worked great but today, couple hours ago i tried to upload some stuff by activesync, suddenly pda disconnected and hanged, so softreset and nothing - its stuck on bootscreen where there is info about my components:
ipl 2.26
spl 2.26
gms 02.61.11
os 3.3.0.0 (was something like 10.xxx... but i flashed faria 3.5aku and now is 3.3)
i also tried to format but msg FormatFailed appear :/
it is possible to run in bootloader and charger also charge my wizard
what to do ????
Do you have a copy of the Wizard Love rom? If so, install that in bootloader mode. Remember to plug your USB cable into the phone.
drivex said:
I dont know what to do... Yesterday i flashed my wizard to wm6 mb rom, everything worked great but today, couple hours ago i tried to upload some stuff by activesync, suddenly pda disconnected and hanged, so softreset and nothing - its stuck on bootscreen where there is info about my components:
ipl 2.26
spl 2.26
gms 02.61.11
os 3.3.0.0 (was something like 10.xxx... but i flashed faria 3.5aku and now is 3.3)
i also tried to format but msg FormatFailed appear :/
it is possible to run in bootloader and charger also charge my wizard
what to do ????
Click to expand...
Click to collapse
i am after updating and still wizard hangs up on boot screen. versions has changed and bootscreen logo too, what now ? ;((((
drivex said:
i am after updating and still wizard hangs up on boot screen. versions has changed and bootscreen logo too, what now ? ;((((
Click to expand...
Click to collapse
I would suggest flashing back to a carrier aku2.x rom and ensure that your phone will come up properly on it. If it does then good, it's most likely not a serious hardware issue, if not then you might be out of luck.
looks like a brick to me..
So sorry m8.
I hope you can revive it !
Had similar problem with the Super rom.What worked for me was taking a back up on the memory card and reflashing from the card.Read the Wiki about details on how to go about it.
Try to flash the latest t-mobile ROM found on their site if all the suggested doesnt work..
@ DRIVEX
Try Hard resetting via the harware Buttons Softreset hole method. Here is how:
----------------------------------
While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key.
Hope it helps.
.
I've done. I used method with mtty and i copied os to sd card, after that i reflashed using minisd card and it works. Thx for everyting, u guyz do great job here hehe
Me too !
cyberdrakula said:
@ DRIVEX
Try Hard resetting via the harware Buttons Softreset hole method. Here is how:
----------------------------------
While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key.
Hope it helps.
.
Click to expand...
Click to collapse
I've been trying many times, but when i did "While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key " but screen appeared FORMAT FAIL. Pls help me...
Pls help me !!!
cachep2004 said:
I've been trying many times, but when i did "While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key " but screen appeared FORMAT FAIL. Pls help me...
Pls help me !!!
Click to expand...
Click to collapse
this is dead your flashrom chip in pda. repair only change semiductors or all board.
Pls show me another ways !
UfOuN said:
this is dead your flashrom chip in pda. repair only change semiductors or all board.
Click to expand...
Click to collapse
I'm living vietnam, so i'm trying to find out another ways, but i think they have no equipments.
Bless god for me.............pls
Revive Wizard
you must use youre camera button on the startup if you got error 260.
You see a lot of collors on youre display and then you can flash youre phone again.
Thanks alot !
sleurhut said:
you must use youre camera button on the startup if you got error 260.
You see a lot of collors on youre display and then you can flash youre phone again.
Click to expand...
Click to collapse
Thanks alot my friend, I will do it !
"FORMAT FAIL" again again pls ... help me !
( I've been trying many times, but when i did "While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key " but screen appeared FORMAT FAIL. Pls help me...)
Pls ! Help me...."FORMAT FAIL" again again pls ... help me !
The hard reset doesnt work
I cant even get the screen to go on anymore. When I plug it in the light doesnt even go on to indicate that it is charging. SOmeone help me please.
ecomajor said:
I cant even get the screen to go on anymore. When I plug it in the light doesnt even go on to indicate that it is charging. SOmeone help me please.
Click to expand...
Click to collapse
Hard to help someone that hasn't told us anything.
From the sounds of it your battery has died. Until you get a good rom on there, the phone will NOT charge. You will need to find someone with a similar phone (or maybe go to your cell provider) and get them to charge the battery at this point. Once you have the battery charged then try following this step by step:
http://forum.xda-developers.com/showthread.php?t=298613
If that doesn't work, then come back and tell us more about what happened, what your IPL/SPL is, what type of phone you have, if its G3 or G4, etc... People here will help, but not without information.
mfrazzz said:
Hard to help someone that hasn't told us anything.
From the sounds of it your battery has died. Until you get a good rom on there, the phone will NOT charge. You will need to find someone with a similar phone (or maybe go to your cell provider) and get them to charge the battery at this point. Once you have the battery charged then try following this step by step:
http://forum.xda-developers.com/showthread.php?t=298613
If that doesn't work, then come back and tell us more about what happened, what your IPL/SPL is, what type of phone you have, if its G3 or G4, etc... People here will help, but not without information.
Click to expand...
Click to collapse
I have G3. i think its 2.25. I was trying to flash my rom when this all happened.
is there any way to charge it without a good rom?
ecomajor said:
I have G3. i think its 2.25. I was trying to flash my rom when this all happened.
is there any way to charge it without a good rom?
Click to expand...
Click to collapse
Not that I know of. Thats one of the reasons its recommended you start with a battery that has over 50% charge (personally I never flash with less than 100% in case something goes wrong). Not saying you didn't do that, but you appear to now be trying to work with a dead (or almost dead) battery, and that will only make things worse if you try to flash and then the battery dies in the middle (maybe not worse, but it sure won't help).
Like I said, you'll need to find someone with a similar phone or see if your local cell provider office will let you charge it (or swap it for a charged battery).
I got my ppc back up and I tried reflashing again and I have almost the same issue. It says format is successfull but then it gets stuck at the blue screen.
Hello guys!
Sorry my bad english!
I installed to WM6.5 ROM in my HTC phone in february. I used may months, all day...
And yesterday i switch on my phone, put on my desk, and today, i see , that the screen get white. It dont do nothing, just get white. I restart the phone many times, and remove the battery, the phone do this: i enter my security password (i locked my phone) and then its go to white screen, and dont do nothing. And if i swich on my phone, and dont do nothing, its just go to frozen...
A dont install nothing my phone since many weeks.
Maybe, the WM6.5 ROM was out of date???
I dont know, but if i connected my phone to PC, the PC isnt known my device...
I dont do nothing, my phone was dead, and im a big trouble (((((((((((
PLEASE HELP ME!
did u try to hard reset it?
can u still enter bootloader mode?
if u can still enter bootloader then try flash another ROM
I think there is a timebomb in the Rom you are using.
Go to bootloader menu, connect to usb, and try to flash an other rom by installing via Windows.
okay, but what is the hard reset? Is that a red button on my device back?
if it is, i try this, but it isnt solve my problem.
and how i can go the bootloader menu?
thank a lot.
Don't worry...just try the hardreset:
1. With the device turned off, press and hold the VOLUME UP and VOLUME DOWN buttons, then briefly press the POWER button.
2. Continue pressing the VOLUME UP and VOLUME DOWN buttons until you see this message on the screen:
This operation will delete all your personal data, and reset all settings to the manufacturer default settings. Press VolUp to restore manufacturer defaults, or press other keys to cancel.
3. Release the VOLUME UP and VOLUME DOWN buttons.
4. Press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset.
If this does not work...just flash another rom...it really seems to have this timebomb issue...you don't have a hardware problem...it's just the software.
here's a video instruction for the hard reset:
http://www.youtube.com/watch?gl=DE&hl=de&v=Eqg8XFJyHBY
thanks a lot, the hard reset worked!!!
thanks!!!
i will flash a new 6.5 ROM.
VorosAdam said:
Hello guys!
Sorry my bad english!
I installed to WM6.5 ROM in my HTC phone in february. I used may months, all day...
And yesterday i switch on my phone, put on my desk, and today, i see , that the screen get white. It dont do nothing, just get white. I restart the phone many times, and remove the battery, the phone do this: i enter my security password (i locked my phone) and then its go to white screen, and dont do nothing. And if i swich on my phone, and dont do nothing, its just go to frozen...
A dont install nothing my phone since many weeks.
Maybe, the WM6.5 ROM was out of date???
I dont know, but if i connected my phone to PC, the PC isnt known my device...
I dont do nothing, my phone was dead, and im a big trouble (((((((((((
PLEASE HELP ME!
Click to expand...
Click to collapse
I'm curious wich rom you use?
you CHICKEN >"<
quack quack
vodanh2025 said:
you CHICKEN >"<
Click to expand...
Click to collapse
lol chicken?
Sorry, but its dont solve my problem, all 6.5 ROMs go to freeze a few sec/minutes when i use... And the phone function and network connection also dont work. Big trouble (
and all rom go to 256 depth colour screen, when im swich on my Blackstone...
but when i push the power button, and push again, the screen go to normal.
but, if i use the device, go to freeze all of ROMs...
brühühühüüü
VorosAdam said:
and all rom go to 256 depth colour screen, when im swich on my Blackstone...
but when i push the power button, and push again, the screen go to normal.
but, if i use the device, go to freeze all of ROMs...
brühühühüüü
Click to expand...
Click to collapse
Flash the latest Hard SPL http://forum.xda-developers.com/attachment.php?attachmentid=179550&d=1240516932
I'm curious, what way did you flash these roms. Are you using USPL or HSPL or have you just flashed these straight from stock?
i used an older february HSPL, now, i will put on my device the latest version, thanks the idea!
VorosAdam said:
i used an older february HSPL, now, i will put on my device the latest version, thanks the idea!
Click to expand...
Click to collapse
2 versions of HSPL, 1.14 & 1.56. You will need HSPL 1.56 on your device to be able to use roms based on 1.56+
thanks a lot, i flash the new HSPL, and now, all phone function back to normal!!!
THANKS!!
Impressed by the support
Hello,
I was watching this thread continously and whenever i try to jump in to help you with tips about flashing, someone would have done it already.
I feel somewhat releived to know that your Kit(d) is back on track.
I like this forum very much not just for the solutions but also for the people's attitude.