AT Commands - P3600 Software Upgrading

Hi folks,
can anybody check the output from mtty with:
USB> rtask b
[email protected]
for me and copy the content after 2 minutes (the nmea gps traffic) into a *.txt and send it to me or attach it to a reply? please, please....
Thank you
PS: You must have bootloader <= 1.04, otherwise the commands do not work.

Hi,
okay now, i think i understand why nobody answers me, because nobody have the bootloader 1.04, right?
But maybe anybody could check if it works with a sspl fake bootloader?
Thanks and please write also, if it does not work

Hello.
i try to help you but nothing happend when i write the command,of caurse with sspl. cause my bootloader is 1.7.
command error. both of trye's
so you nead a device with 1.4 b.l.

thanks ausdim!

Related

mtty.exe not working!!!

Hello!
Where I can download mtty for Trinity?
http://wiki.xda-developers.com/uploads/mtty.exe not working!!!!
Hello, so that its it functions is necessary to neutralize (wcescomm.exe) ActiveSync and then to select port USB in mtty.exe.
I have SPL-1.01 MFG, but......
USB> task 32
Level = 0
Cmd>lnb C:\finalsplash.nb 500e0000
:F=C:\finalsplash.nb
:A=501A0000
:O=00000000
:L=FFFFFFFF
start NB image download
Click to expand...
Click to collapse
On this step, process stoped
BE WARNED THIS ROM ADDRESSES ARE FOR HERMES, NOT FOR TRINITY... flashing the wrong address can brick your device!
you have to use mtty 1.16 for the lnb command to work.
Take it from here:
ftp://xda:[email protected]/Hermes/Cooked_ROMs/SPL-1.01MFG_Pack.zip
pof said:
BE WARNED THIS ROM ADDRESSES ARE FOR HERMES, NOT FOR TRINITY... flashing the wrong address can brick your device!
Click to expand...
Click to collapse
Say me, please ROM adress for Trinity!
Sorry, my English very bad....
lvsw said:
Say me, please ROM adress for Trinity!
Click to expand...
Click to collapse
sorry I don't have a Trinity and I don't know what is the ROM layout on it, you can investigate yourself capturing the output of the RUU while flashing a rom with usb monitor, dumping rom parts with rbmc bootloader command, and dumping mmu and parts of mem from gnuharet... but it's a long process until you manage to get all the addresses correctly. You have to compare what you get from the device with the *.nb file extracted from the NBH to see where each part of the ROM starts. Can't really do this without having a Trinity on my hands
Problem using mtty
I have some ploblems using mtty.... I deselect "connect to USB" in pc activesync, then I connect the pocket pc on the usb cable, then I start mtty and I select USB.... I have a the mtty window in which is written CLIENT then, again, CLIENT, and the pocket pc... CONNECTING TO USB... and this situation remain without any changement.... where I am wrong?
pof said:
you have to use mtty 1.16 for the lnb command to work.
Click to expand...
Click to collapse
Actually, the LNB command must be implemented in the bootloader to work. If you connect to Trinity using any version of MTTY (from 1.10 to 1.46) and type LNB, it will just give an "Command error!!!" message.
yes, but seems to be implemented on the MFG bootloader version that is left on the device after unlocking it with imei-check unlocker, isn't it?
can't get MTTY to connect w/ Trinity
dr-jo said:
Hello, so that its it functions is necessary to neutralize (wcescomm.exe) ActiveSync and then to select port USB in mtty.exe.
Click to expand...
Click to collapse
Not that I think it should matter much but in case it does I'll say first that I'm running a PC w/ Vista and not xp or earlier.
Anyway, I can't get MTTY to connect to my Trinity.
The only port that MTTY can open is my Com3. All other ports, inluding the one titled "USB" can not open.
When I have MTTY open on Com3, there is no response to any command so I suspect although the application is occupying the port, it is not communicating w/ the Trinity.
Can anyone provide some insight here or tell me the correct com port settings (parity, baud, stopbits, etc)?
Thanks,
J
I tried MTTY on my WinXP notebook as well. I get the same situation. I downloaded a freeware terminal emulator application also but wasn't able to establish coms w/ the Trinity either.
Can someone confirm their com settings in MTTY?
The same thing has happened to me on p3400i, the New Gene, followed the guide at XDA to every letter, though I knew my device was a new Gene. Now the mtty program opens with some settings window instead of the USB button. Only port accessible is COM3. Flashed and bricked by Olipro SPL.

Rescue for my Trinity...

Hi All, (sorry for my language)
I can not upgrade or use my Trinity. Device freezing while booting-up. And Red NO GSM message appears on the bottom line. When blue Windows Mobile splash screen comings up, device freezing.
I'm trying to re-flash with SD card method (extract nbh file and rename to TRINING.nbh and put to te SD card and start manual bootloader) NOT ALLOW message appears on the upper line.
My device SPL version is 1.05. How can i rescue my trinity?
Thanks in advance...
seem u upgrade wrong version...try flash with original OS ROM, or else return to "them" to repair....
If you can figure out how to compile splxploit, you can fix this, see
http://forum.xda-developers.com/showthread.php?t=308691
@stepw,
Thank you stepw. Problem is "how to compile splxploit" I'm using Windows XP OS on my notebook.
RUU_signed.nbh extracted and waiting for next steps.
What is the next steps, who can explain to me.
Thanks in advance
ya, i try mingw to compiler but doesn't work. or it say error somewhere on file splxploit.c......Just wait for new answer. I brick my dopod810...and i'm waiting for your answer....
tuannghia1985 said:
ya, i try mingw to compiler but doesn't work. or it say error somewhere on file splxploit.c......Just wait for new answer. I brick my dopod810...and i'm waiting for your answer....
Click to expand...
Click to collapse
The issue was resolved for tuannghia1985 in the other thread
I am trying to use the splxploit, but am not at all familiar with Linux. Could do with a few pointers ....
I am using a Live CD of Knoppix on my windows PC. It appears to run very well, and seems to have gcc installed already as default.
What I did was unzip the splxploit.c file to the desktop and then went to the run command and typed "gcc splxploit.c -o splxploit" a console popped up, but gave a message saying gcc : couldn't find file or directory". I tried various combinations e.g "gcc home/knoppix/Desktop splxploit.c -o splxploit" but just couldn't get it to work. I think I am just telling the gcc program to look in the wrong place.
ANy help would be appreciated !!
gaz

can't format extRom..

hi people...
i tried to install a wm5 and a wm6 rom in a qtek 9090 but i can't format and merge ExtRom... i tried to use the rom unlocker found in the a77ila wm5 rom pack but i have a lot of error during unlock.. and when i try to format this error will show: FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed!
i tried with xda-developer unlocker but an unable to find exe file will show..
and repart_doc still not work...
anyone can help me?
my device:
qtek 9090
SO WM2003SE ver. 4.21.1088 (Build 15045.2.6.0)
ROM : 1.40.04ITA
Radio: 1.12.00
Prot Ver: 1337.42
ExtRom ver: 1.40.153 ITA
tnx in advance... and sorry for my bad english
1. You cannot reformat extROM without unhiding and unlocking it first. Follow the procedure step by step. (remeber aboutsoft reset
2. Correct links to both tools as well as the procedure you can find on Wiki (http://wiki.xda-developers.com/index.php?pagename=Helmi - Installation)
3. Report effects.
3b. Your english is OK
here i am...
followed tutorial step by step...
1. installed the unlocker
2. launched unhide
3. soft reset
4. launched unlock
5. system displays a windows named debug showin ERROR: press OK
6.another system window named debug showin FL_IOCTL_BDTL_HW_PROTECTION press ok
7. another window saying a peripheral connected to system in not working press ok
8. a debug window saying extrom unlocked
9. soft reset
10. launched repart_doc
11. error window saying "FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed" press ok
tried also without soft reset at point 9. same results..
i only see Ext_Rom in memory page of Setting but still remain full
------------------------------------------------------------------
Finally solved...
i don't know why but ita extrom can't be formatted...
so i used an escamotage... upgraded qtek9090 with this rom BA_TMNL_14200_119_11300_Ship
After used unlocker and repart_Doc and all goes on....
now go to upgrade to HELMI_BA_WM6_R0_Public
hiya
i cannot format my DOC too, i got the same error ,
i used TASK 28 under MTTY , but still i'm getting this error.
anyone can help with this problem ?
Hiya
I was searching XDA-DEVELOPERS website about 2 days to find a solution for this problem, I have an I-mate PDA2K, i used all EXTROM tools on this website like this:
1- Installed EXTROM_tools,
2- run UNHIDE ,
3- then run UNHIDE,
4- Soft Reset,
5- now i can see Extended_ROM on my file explorer, i can read it , and able to write on it ... copy paste ...
6- run REPART_DOC.exe on my device,
7- tried many sizes like 128kb, 1024, 2048, 512, 61000, .................
but on this step i always get the god damned FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed,
i finally used Task 28 under MTTY but nothing happened, still have this problem,
No Wayyyyyy ! No wayyyyyyyyyy to repart my DOC size, .... noooooooooooo wayyyyyyyyyyyyyyyy
anyone going to help me plzzzzzzzzzzz ?
try it in this order...
1. downgrade to 2003
2. in WM2003 unlock... unhide... softreset
3. then repart_doc...
4. then upgrade to WM5/WM6
PS:
@Borbor...
hmm... i cannot see any part on your post that you tried to UNLOCK the extrom.
mastermoon DID. you need to unlock it first in order to modify it.
unhiding it just simply makes it visible to filemanagers.
SilverSamurai said:
try it in this order...
1. downgrade to 2003
2. in WM2003 unlock... unhide... softreset
3. then repart_doc...
4. then upgrade to WM5/WM6
PS:
@Borbor...
hmm... i cannot see any part on your post that you tried to UNLOCK the extrom.
mastermoon DID. you need to unlock it first in order to modify it.
unhiding it just simply makes it visible to filemanagers.
Click to expand...
Click to collapse
Hiya
I'm not a braincracked one, I'm a computer software engineer and i write CNC machines programs, so i don't need to someone to teach me instructions !!!! i did all, but i got FL_IOCTL_FORMAT_PHYSICAL_DRIVE failed. !
find me a good solution plz !
and i thought landmark's the only one who is bossy...
if you dont need instructions then what are you looking for in here??? duh!!!
you're both at the same level of intelligence... are we downgrading humans now?
P.S.
look at the end of the third post... that is solved.
Everybody is allowed to name themself software engineers nowadays?
Please people start behaving like grown up's we are no longer in kindergarten.
Please:
- listen to each other
- be prepared to be wrong
- try explaining your problem in another way
- but most of all don't try to solve your listening problems by yelling and cussing to each other.
TIA, Flar

Trinity Call duration reset please help??

I install hard spl 1.3 then try to reset my htc p3600 trinity with this command in mtty bat not work , i try this and work in hermes and kaiser bat in trinity not. So can somebody helo me to reset call duration in trinity please and write how and what need to do.
this command in mtty and hard spl1.3 not work i try this:
1) put device in bootloader mode
2) disable activesync usb connections
3) connect to bootloader using mtty.exe
4) when you see "USB>" prompt type this (DO NOT COPY-PASTE):
rtask b
0 <--- wait until you see a "0" here
ate1 <--- enable local echo
atv1 <--- verbose output for return values
[email protected]?1 <--- get outgoing call time
[email protected]?0 <--- get incoming call time
[email protected]=270F,270F reset both counters BAT RECEIVED ERROR??
In hermes 100% work with hard spl1.2 and in kaiser when security unlock also work bat why this not work in TRINITY . Is any solution that can help me to reset call duration .plaase do not sent message that hard reset will remove call duration .!!! this also not work As i can see i need special bootloader i mean hard spl that this command work..So who can help???
try with hard spl1.2
try with hard spl1.2 - radio upgrade will also not work with hard spl1.3 on the trinity -
Carlo626 said:
try with hard spl1.2 - radio upgrade will also not work with hard spl1.3 on the trinity -
Click to expand...
Click to collapse
With hard spl 1.2 command rtask b in mtty not work ,so plase only write if you try and know that work.
i tried without success.maybe no way to reset it until now
Finaly work after use trinity unlocker and hard spl 1.3
Cmd>rtask 4
Cmd>rtask 7
Enter Radio Image
AT-Command Interpreter ready
0
atv1
OK
[email protected]?1
@TALK: 00003B3F
OK
[email protected]?0
@TALK: 00005176
OK
[email protected]=270F,270F
OK

HELP plssss...

HI... can any body help me on my problem....
HERA100 After HARD SPL it does'nt Power ON (only Bootloader )
IPL. 1.08.0001
SPL. 1.08.0001
any solution PLS...
i saw this >>> http://forum.xda-developers.com/showthread.php?t=417930 <<< thread, but some links there are not available...
can anybody have this, and put it here???
thanks in advance
oasisnhoa
Hmmm have you read stickies?
ai6908 said:
Hmmm have you read stickies?
Click to expand...
Click to collapse
Thanks, just only now, and i am also a newbie, and have dial up connection only ...
And what i find is, if anybody has a solution for this.... or give easiest solution how to make this.
And, if someone who tried that GOLDCARD, Pls. upload the file here....
Thanks In Advance
oasisnhoa08 said:
Thanks, just only now, and i am also a newbie, and have dial up connection only ...
And what i find is, if anybody has a solution for this.... or give easiest solution how to make this.
And, if someone who tried that GOLDCARD, Pls. upload the file here....
Thanks In Advance
Click to expand...
Click to collapse
You can't upload the Goldcard as it is dependant on the HARDWARE serial number on your SD card.
ivanmmj said:
You can't upload the Goldcard as it is dependant on the HARDWARE serial number on your SD card.
Click to expand...
Click to collapse
ahhh ok...
but you have some files there that can i use by making a GOLDCARD??? like this
4) Crypt-DES and XdaDevelopers-NbfUtils PERL packages
5) typhoonnbfdecode.pl PERL program
6) itsutils tools
Thanks In Advance...
Try http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard
ivanmmj said:
Try http://wiki.xda-developers.com/index.php?pagename=Elf_GoldCard
Click to expand...
Click to collapse
Hi...
i am sorry for my late reply, cause i find my friend who have WM...
Now my problem is... How can i see the SERIAL No. of memory card???
I try to use this application >>> http://www.wizcode.com/downloads/pocket_mechanic_professional,,, but it doesn't work...
pls... everybody help me for my problem... tnx
bR
Hello...
I am here again, forcing to make my HERA100...
I make a goldcard on QMAT and it says successful...
and check it to MTTY...
and here's the logs...
Code:
Cmd>set32
Invalid command : set32
For a help screen, use command ? or h
Cmd>password BsaD5SeoA
Pass.
+ SD Controller init
- SD Controller init
+StorageInit
SDInit+++
PL_SDSetSlotNumber() - MPUIO_SDIF_SEL1=0, MPUIO_SD_IF_SEL=0
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDCmd8 Command response time-out. MMC_STAT = 80
SDInit - SD ver1.0
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SDCmd1 Command response time-out. MMC_STAT = 80
SD clock to 24MHz
***** user area size = 0x1E580000 Bytes
SDInit---
SDInit OK
Unlimited time!
GetDeviceCID: Error - InitDecoder
g_cKeyCardSecurityLevel = 0
HTCEType (0x1)(Operation mode flag): cOpModeFlag=(0x0).
Type (0x2)(Back color flag): cBackColorShowFlag=(0x1).
Type (0x5)(Background color value): g_wBColor=(0xC618) (0xC0C0C0).
RUURUN fail
HTCSF
so whats wrong about that???
pls.. Help us..
bR

Categories

Resources