Related
Does it need to downgrade SPL/IPL first to version 1.xx ?
When I try to upgrade ROM in my SPV m3000 from ver 2.x to another one ver 2.x I always need to do following tasks:
1. Downgrade IPL/SPL to ver 1.01 using wizBackup tool
2. Afetr that I'm unable to upgrade ROM using ROMUpdateUtility_Wizard_NoID.exe (connection error), I have to restore original ROM ver 1.3.1.15 from SD card (from my backup)
3. After ROM is restored (ver 1.3.1.15, IPL/SPL v1.03), I'm able to upload new ROM (any newer)
But this procedure is too much complicated. Maybe, there is another solution (trikc) to save time.
Thanks in advance
Krzychu
ksalawa said:
Does it need to downgrade SPL/IPL first to version 1.xx ?
When I try to upgrade ROM in my SPV m3000 from ver 2.x to another one ver 2.x I always need to do following tasks:
1. Downgrade IPL/SPL to ver 1.01 using wizBackup tool
2. Afetr that I'm unable to upgrade ROM using ROMUpdateUtility_Wizard_NoID.exe (connection error), I have to restore original ROM ver 1.3.1.15 from SD card (from my backup)
3. After ROM is restored (ver 1.3.1.15, IPL/SPL v1.03), I'm able to upload new ROM (any newer)
But this procedure is too much complicated. Maybe, there is another solution (trikc) to save time.
Thanks in advance
Krzychu
Click to expand...
Click to collapse
- Downgrade to 1.xx rom
- CID unlock the phone with lokiwiz 0.2b (NOT 0.3a!!!)
- Install whichever rom you like
You don't need to repeat the CID unlock every time you change rom. CID unlock is needed only once. Once you have CID unlocked, you can install whichever rom you like by simply running the rom's executable.
bye
Amny thanks,
I did it at the begining (few times - SIM unlock, CID unlock, using lokiwiz0.2b) and I was able to upgrade from my original ROM (1.x) to any other (2.x). But then I was unable to upgrade to another one (2.x) - I got message from RomUpdateUtility about errors in the middle of upgrading.
But from yestarday, this problem disappear, I don't know what happened. I did another few attempts to unclok SID, but using aWizard (enable RAPI then unlock) instead of lokiwiz - maybe I had problem with disabled RAPI - does lokiwiz 0.2b enable RAPI?
Fortunately, right now I don't have such problem
MANY THANKS FOR HELP
ksalawa said:
Amny thanks,
I did it at the begining (few times - SIM unlock, CID unlock, using lokiwiz0.2b) and I was able to upgrade from my original ROM (1.x) to any other (2.x). But then I was unable to upgrade to another one (2.x) - I got message from RomUpdateUtility about errors in the middle of upgrading.
But from yestarday, this problem disappear, I don't know what happened. I did another few attempts to unclok SID, but using aWizard (enable RAPI then unlock) instead of lokiwiz - maybe I had problem with disabled RAPI - does lokiwiz 0.2b enable RAPI?
Fortunately, right now I don't have such problem
MANY THANKS FOR HELP
Click to expand...
Click to collapse
lokiwiz 0.2b and awizard use the very same procedure to CID unlock the phone so both require to enable the RAPI. Maybe you didn't enable it when you used lokiwiz the first time.
Anyway i'm glad that it finally worked! Bye
ksalawa said:
Amny thanks,
I did it at the begining (few times - SIM unlock, CID unlock, using lokiwiz0.2b) and I was able to upgrade from my original ROM (1.x) to any other (2.x). But then I was unable to upgrade to another one (2.x) - I got message from RomUpdateUtility about errors in the middle of upgrading.
But from yestarday, this problem disappear, I don't know what happened. I did another few attempts to unclok SID, but using aWizard (enable RAPI then unlock) instead of lokiwiz - maybe I had problem with disabled RAPI - does lokiwiz 0.2b enable RAPI?
Fortunately, right now I don't have such problem
MANY THANKS FOR HELP
Click to expand...
Click to collapse
lokiwiz 0.2b and awizard use the very same procedure to CID unlock the phone so both require to enable the RAPI. Maybe you didn't enable it when you used lokiwiz the first time.
Anyway i'm glad that it finally worked! Bye
Hi people. I have updated my Wizard with wm6, and it works great for weeks. Today, i have to reinstall the rom because one error... I installed that correctly but the ppc turns on and shows: HTC IPL:2.18, SPL:2.18... And dont go on! I can access to bootloader mode, but nothing it all. What i should do?
It is possible that you didn't unlock properly before flashing.
If you CID unlocked your Wizard when IPL is 2.18, then it is NOT unlocked. Follow the unlocking stickies in this forum and use Button's 1.05 ROM to unlock again.
If you are sure that you unlocked CID in IPL 1.xx, then just start RUU in bootloader mode and everything should be fine (You may need to disable USB connection in ActiveSync for RUU through bootloader to work properly)
He can't do that. Phone doesn't go past the bootloader and is indeed CID locked and also doesn't accept any flash.
But then again, button rom might do the trick...
No, my Wizard used to be the same situation. As soon as IPL not upgraded to 3.08, there is a high possibility to flash Button's 1.05 ROM into the device without problems.
Problem solved! I downloaded a ROM from here, whitch downgraded my IPL and installed WM5.. Now im waiting for the orders of mestrini
Hello
For first i had installed 1.30 oilpro and Radio 1.50xxx
Than i had installed SSPL.
Is it normaly that when im flashing rom apears the bootloader sspl (by des), and when i enter the bootloader manualy i see the oilpro 1.30 ecc.
the only problem is that the rom update aborts after starting bootloader, and i must restart the setup in bootloader mode.
How to reset the phone to original Bootloader and radio, and where to find it?
Need i SSPL or can i work only whit spl (Oilpro)??
What are the kommands to reset and format it complete in original status?
Sorry by my bad english
i'd also like to know
Your english is good.
I also have some problem to upgrade the rom.
I did so many test, that like you I'd like to go back to intial satge.
http://forum.xda-developers.com/showthread.php?t=377502
Let's wait some help
!!! USE THIS GUIDE ONLY IF YOU KNOW WHAT YOU ARE DOING !!!
!! READ THE END OF THE GUIDE FIRST(Very Importnat)
Aplication Unlock - lets you run unsigned software
SSPL - Software Second Program Loader is a boot loader after IPL (Initial Program Loader) often seen on smart phones and PDA:s.
- Lets you flash any rom on the phone
SPL 1.09 http://rapidshare.com/files/106089565/MTeoR_-_EUR1.09SPL.rar.html
[B]official HTC ROMS[/B]
RUS
http://rapidshare.com/files/106091396/RUU_MTeoR_1.34.261.1_1.38.00.10_HTCRUS_SHIP.rar.html
UNLOCK TOOLS
http://rapidshare.com/files/105133496/Unlock_HTC.rar.html
1. Folder "1"
put the file "SP_AllowCertificateInstall.cab" into the temp folder on you mobile phone (use active sync)
to connect. Execute the cab file on your phone.
2.Folder "2"
make sure you are connected to the phone threw active sync. Now run "EnableRAPI.bat" it will say if
it has succeded.
3.Folder "3"
make sure you are connected to your mobile phone through active sync. Start "MobileRegisteryEditor.exe"
Now go to SPV_C600 than HKEY_LOCAL_MACHINE than Security than Policies than Policies
so that you are in HKEY_LOCAL_MACHINE\Security\Policies\Policies
Now dubble click 00001001 (the first one after (Default)) and change the value to 1
Now dubble click 00001005 (the second one after (Default)) and change the value to 40
4.Folder "4"
put the file "Cert.cab" into the temp folder on you mobile phone (use active sync)
to connect. Execute the cab file on your phone.
5.Folder "5"
install and run HTC Security Manager.msi
select Security Off
Wait
YOUR PHONE IS APPLICATION UNLOCKED
6. Restart the phone
press and hold CAMERA+POWER while powering
you should see spl version
NOTE THAT VERSION
PULL OUT THE BATTERY AND POWER THE PHONE
7.1 Try to flash wwe rom directy
if you have wwe use sspl 1.01 http://forum.xda-developers.com/attachment.php?attachmentid=38680&d=1178637546
WWE rom
http://rapidshare.com/files/106091341/RUU_MTeoR_1.34.251.1_1.38.00.10_HTCEUR_SHIP.rar.html
after this you need to begin from step 1 till you see spl 1.10
now you have SPL 1.10 and CID HTC__Z12
jump to step 8
7.2 If 7.1 does not work try
7.2.1.SPL 1.09 http://rapidshare.com/files/106089565/MTeoR_-_EUR1.09SPL.rar.html
now you have SPL 1.10 and CID HTC__A07
7.2.2.you need to run the RUS update
RUS
http://rapidshare.com/files/106091396/RUU_MTeoR_1.34.261.1_1.38.00.10_HTCRUS_SHIP.rar.html
after this you need to begin from step 1 till you see spl 1.10
jump to step 8
8.flash any rom
now to flash an rom use SSPL 77.7 http://rapidshare.com/files/106072098/SSPL.rar.html
Copy the coresponding SSPL to the ROOT of the PHONE not the SD-CARD
run SSPL on the phone and immediatly press CAMERA+POWER
YOU SHOULD SEE TRI-COLOR SCREEN displaying spl 77.7
This SPL is allowing you to flash latest radio
or to Flash any rom usin sspl 77.7
Run the update from the PC
VERY IMPORTANT
i found a way to installl hardspl
1. unplug phone from usb
2. take out the battery/put it back
3. enter bootloader (press camera+power)
4. check for spl if it sais 2.05 you can go further if not read the fisrt guide
5. enter in windows
6. extract and copy to device root http://rapidshare.com/files/138396463/breeze_HARDSPL.rar.html
7. copy to storage card root BREEIMG.NBH
8. it should say SPL-1.01
9. follow onscreen instruction for the update
10.enter in windows and delete BREEIMG.NBH from card
11.enter bootloader (press camera+power)
12.it should say spl 7.77
13.be happy now you have hardspl and you can flash any rom (without sspl)
BEST REGARDS
i don't know whats the problem with appunlocking... there are 5 Regkeys that have to be set,... it stands all in wiki
http://wiki.xda-developers.com/index.php?pagename=Breeze_Registry
Application Unlock
http://wiki.xda-developers.com/uploads/Policies.reg
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"00001017"=dword:00000090"00001005"=dword:00000028"00001001"=dword:00000001after doing this run SDAunlock app (google for it) or
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101b"=dword:00000001
Running unsigned Apps without confirmation!
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101a"=dword:1
GREATLY APPRECIATED! finally some good explainations. so let me get this straight,
SSPL = application unlock? (im asking this because i already have my phone app unlocked using SDA security unlock software)
i have a dopod 595 and,
my IPL is 0.90 (do i need to update this?)
SPL is 2.05 (so i need to use the SPL>1.09)
radio is 1.06.00.10 (do i need to update this?)
RIL is 2.002
do i need to update anything before i try your WM6.1? which is the latest versions (IPL,Radio) you would recommend and can you please provide the links too. also, will the forward facing video call camera work with your ROM?
from wiki, it looks like there is the Radio:1.38.00.10 Protocol:32.71.7020.12H RIL:2.002 SPL:1.10.0000 ROM, and other older Radio ROMs but with newer SPL. so in order to update my radio, do i need to flash the entire ROM into my phone, or can i just use a Radio ONLY rom updater?
Please bear with me, because i really do not want to brick my phone.
Admin, please make this thread sticky. cheers
alexnvidia said:
GREATLY APPRECIATED! finally some good explainations. so let me get this straight,
SSPL = application unlock? (im asking this because i already have my phone app unlocked using XDA unlock software)
i have a dopod 595 and,
my IPL is 0.90 (do i need to update this?)
SPL is 2.05 (so i need to use the SPL>1.09)
radio is 1.06.00.10 (do i need to update this?)
RIL is 2.002
do i need to update anything before i try your WM6.1? which is the latest versions (IPL,Radio) you would recommend and can you please provide the links too. also, will the forward facing video call camera work with your ROM?
from wiki, it looks like there is the Radio:1.38.00.10 Protocol:32.71.7020.12H RIL:2.002 SPL:1.10.0000 ROM, and other older Radio ROMs but with newer SPL. so in order to update my radio, do i need to flash the entire ROM into my phone, or can i just use a Radio ONLY rom updater?
Admin, please make this thread sticky. cheers
Click to expand...
Click to collapse
i had 2.05 spl
i flashed the 1.09 spl from first topic
i flashed the latest wwe rom
now i have 1.10 spl
radio 1.38 from oficial rom
app unlocked
sspl
flashed wm6.1
jerpelea said:
i had 2.05 spl
i flashed the 1.09 spl from first topic
i flashed the latest wwe rom
now i have 1.10 spl
radio 1.38 from oficial rom
app unlocked
sspl
flashed wm6.1
Click to expand...
Click to collapse
im going to flash to WWE now with this version : HTC MUI BREE100 1.34.251.1 1.38.00.10 32.71.7020.12H 15673.3.3.1 3.3.1 2.002 1.10.0000 , then update to your WM6.1.
am i doing the steps right?
OK, i've done all the steps you provided in post no.1 (great instructions by the way). problem, when i run SSPL on the root of the device, the screen close blank and nothing happens even though im still pressing the camera+power button. what should i do now?
OK, i've done all the steps you provided in post no.1 (great instructions by the way). problem, when i run SSPL on the root of the device, the screen goes blank and nothing happens even though im still pressing the camera+power button. i had to unplug the battery to restart the device. am i doing anything wrong here?
Update : Now i got it. i had to run the SPL link, not the SSPL.exe as written in the first post. must be a typo.
Update2 : Success!! flashed to WWE. now proceeding to your WM6.1!!
Update3 : Running WM6.1 B1 now! thanks jerpelea! you're the man!
Admins please make this thread sticky.
I have I-Mate SPJas. I have tried several unlock tools including HTC Unlock toll, resgistry edit, SDA Unlock....
My original SPL version was 2.05 and after I ran SPL file I had IPL=SPL by des and SPL=7......
I have also applied other methods and my phones seems to be application unlock. But when I try to upload a new rom the phone goes to blank. I could never prevent this condition.
Is there a way to update Imate SPJas to Win 6.1? Which ROM works?
caglar_altan said:
I have I-Mate SPJas. I have tried several unlock tools including HTC Unlock toll, resgistry edit, SDA Unlock....
My original SPL version was 2.05 and after I ran SPL file I had IPL=SPL by des and SPL=7......
I have also applied other methods and my phones seems to be application unlock. But when I try to upload a new rom the phone goes to blank. I could never prevent this condition.
Is there a way to update Imate SPJas to Win 6.1? Which ROM works?
Click to expand...
Click to collapse
all roms work
follow the guide and will work
rom
I have gone through all of the steps of ROM update.
When the rom update utility prepare for installing, after I press "ENTER" the device closes immediately and the connection with ActiveSync stops.
In three color screen I see:
IPL SSPL by des
SPL : 1.01
Enter
When I go through root directory and enter to SSPL.exe, the phone again shut down and I have to removE/install battery to start the phone.
Please help!!
caglar_altan said:
I have gone through all of the steps of ROM update.
When the rom update utility prepare for installing, after I press "ENTER" the device closes immediately and the connection with ActiveSync stops.
In three color screen I see:
IPL SSPL by des
SPL : 1.01
Enter
When I go through root directory and enter to SSPL.exe, the phone again shut down and I have to removE/install battery to start the phone.
Please help!!
Click to expand...
Click to collapse
Hi, I had the same issue. Try pressing camera & off' buttons AND Enter all together.
rom update
1- I have updated the current rom to origininal config by manufacturer's original ROM.
2- I applied HTC unlock tool..
3- My first attempt to update rom gave #262 error. Second attempt was succesful.
thanks.
futureshock said:
i don't know whats the problem with appunlocking... there are 5 Regkeys that have to be set,... it stands all in wiki
http://wiki.xda-developers.com/index.php?pagename=Breeze_Registry
Application Unlock
http://wiki.xda-developers.com/uploads/Policies.reg
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"00001017"=dword:00000090"00001005"=dword:00000028"00001001"=dword:00000001after doing this run SDAunlock app (google for it) or
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101b"=dword:00000001
Running unsigned Apps without confirmation!
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101a"=dword:1
Click to expand...
Click to collapse
there are 5 keys unless you have the official security configuration manager
that is setting the other keys for you
BR
HARDSPL
hy all
i found a way to flash hardspl to breeze
this will allow to flash any rom from any cid so that you will not break devices due to wrong cid
BR
is there anyway to hard spl without going into windows? my device is stuck at windows 2nd boot screen (windows mobile 5 logo)
jerpelea said:
hy all
i found a way to flash hardspl to breeze
this will allow to flash any rom from any cid so that you will not break devices due to wrong cid
BR
Click to expand...
Click to collapse
That sounds interesting..!
alexnvidia said:
is there anyway to hard spl without going into windows? my device is stuck at windows 2nd boot screen (windows mobile 5 logo)
Click to expand...
Click to collapse
no
you must get to windows
what is your current cid?
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine. then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
alexnvidia said:
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine. then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
Click to expand...
Click to collapse
you can not do anithing
your ipl does not know how to load spl1.09
send the phone to repair and flash hardspl when it returns
there are many people with your problem
till now we have found not found any solution
BR
my phone is out of warranty, so sending for repair will cost me a lot. we'lll keep our fingers crossed and hope you guys can find a solution for us soon. thank you
i think, SPL version is very confusing. 2.05 is older than 1.09?
Would be good to have compatibility list between SPL and IPL versions to not mess and brick device.
I guess i was lucky, because i updated my breeze to resently posted HardSPL (thanks to jerpelea) and device still alive.
I found that RUUUpdateUt.exe i've used for DES SoftSPL is not working with HardSPL anymore. It cost me a bunch of my nerves (no body mentioned this fact!). Again luckily i found that stock RUU upgrade utility works fine with HardSPL (i just removed all dialogs except first for convenient use).
Well, at last, now i don't need to flash stock firmware (with radio ROM update which is extremely dangerous) every time when one of my cooked ROM refuses to work normally.
Needed
1.an BREEZE device[The phone must be able to enter bootloader (3color screen)]
2.TerraTermPro http://rapidshare.de/files/39206549/TeraTermPro.rar.html
3.An rom matching to your device
GUIDE
1.Disable active sync - uncheck
file->connection settings->allow usb connection
2.Put the phone in bootloader mode
power the phone pressing power and camera keys
read and note all displayed info
3.Launch TerraTermPro on the pc
un the connection window check serial and choose USB
in the new open window type
info 2
and note the information
RIGHT - HTCSQTEK_A07„§m»HTCE
WRONG - HTCSF kEØ(HTCE
close terra term
4.Figure out wich rom you need
till now i have roms for
Russian Rom
QTEK_A07
HTC__A07
http://rapidshare.com/files/109782599/RUU_BREE100_1.34.261.1_1.38.00.10_HTCRUS_SHIP.rar.html
WWE Rom (QTEK,HTC,Dopod,OCH)
QTEK_Z12
HTC__Z12
http://rapidshare.de/files/39206931/RUU_MTeoR_1.34.251.1_1.38.00.10_HTCEUR_SHIP.rar.html
DOPOD001 - Chinese Rom
http://www.megaupload.com/se/?d=YD49L7JD
5.
Flash the rom corresponding to your CID
6.
Boot the phone and application unlock it
7.
Run SSPL and UPGRADE to 6.1 rom and latest radio version
8.
Save the rom that saved you for latter - it colud help you again
IF YOU CANT FIND THE CID AND ROM HERE WAIT TILL SOMEBODY POSTS IT.
IN CASE OF "HTCSF kEØ(HTCE" IN TERRATERM IS VERY HARD TO REPAIR DUE TO DAMAGED BOOTLOADER
you can repair it using this guide
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
wich requires some advanced skills
OTHER ROMS - wich i dont have
i_mate_SP_JAS_1.15.301.0.exe
RUU_BREE100_1.15.71.6_1.06.00.00_OCH_Ship.exe
ruu_bree100_1.15.707.3_dopodwwe_ship.exe
ruu_bree100_1.15.709.3_dopodcht_ship.exe
Please help me to improve this list sending me CID's and ROM's
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
what do you mean by very hard to repair? it's impossible?
this is the ROM i flashed back to my phone (although the flashing is 100% completed successfully, it is still stuck at 2nd boot WM logo screen)
RUU_BREE100_1.15.707.3_DopodWWE_SHIP.exe
i just uploaded th dopod rom in case anyone needs it
http://rapidshare.com/files/109798242/RUU_BREE100_1.15.707.3_DopodWWE_SHIP.exe
alexnvidia said:
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
what do you mean by very hard to repair? it's impossible?
this is the ROM i flashed back to my phone (although the flashing is 100% completed successfully, it is still stuck at 2nd boot WM logo screen)
RUU_BREE100_1.15.707.3_DopodWWE_SHIP.exe
i just uploaded th dopod rom in case anyone needs it
http://rapidshare.com/files/109798242/RUU_BREE100_1.15.707.3_DopodWWE_SHIP.exe
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
use this wisely
jerpelea said:
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
use this wisely
Click to expand...
Click to collapse
how do i put breeze into KITL Mode? is it the camera+power button tri-colour thing?
reads what stands on hermes wiki page...
maybe i'm talking ****, but i think too enter kitl mode you must have a running windows mobile...
just find the kitl mode "reset" on hermes its "now for your Hermes: hold the Comm button and soft reset and wait for the KITL dialog to appear, now is the CRITICALLY missed step; you need to press the small OK button on the LEFT of the device to activate USB KITL. "
futureshock said:
reads what stands on hermes wiki page...
maybe i'm talking ****, but i think too enter kitl mode you must have a running windows mobile...
just find the kitl mode "reset" on hermes its "now for your Hermes: hold the Comm button and soft reset and wait for the KITL dialog to appear, now is the CRITICALLY missed step; you need to press the small OK button on the LEFT of the device to activate USB KITL. "
Click to expand...
Click to collapse
exactly.. that's the worrying part for me now. i have no idea how do i enter KITL mode in breeze. any ideas?
alexnvidia said:
exactly.. that's the worrying part for me now. i have no idea how do i enter KITL mode in breeze. any ideas?
Click to expand...
Click to collapse
no
i did this on my hermes once
having the same problem as you have on breeze
hermes and breeze share the same platform
we have to find the answer
How did you manage to screw the bootloader
can you provide us a list of what you have flashed on the device?
what is the brand,model(herm 100/herm160),vendor,region of your device
i am triing to figure an solution
all others upgraded succesfully to 1.34 rus getting HTC__A07 CID and after that radio and wm 6.1
what did you do ?
BR
jerpelea said:
no
i did this on my hermes once
having the same problem as you have on breeze
hermes and breeze share the same platform
we have to find the answer
How did you manage to screw the bootloader
can you provide us a list of what you have flashed on the device?
what is the brand,model(herm 100/herm160),vendor,region of your device
i am triing to figure an solution
all others upgraded succesfully to 1.34 rus getting HTC__A07 CID and after that radio and wm 6.1
what did you do ?
BR
Click to expand...
Click to collapse
ok. i have no idea hoiw i screwed up the bootloader too. this is what happens.
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine. then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
what should i do now? i really appreciate you/anyone taking the time to look into this issue. thank you.
have you tryed a hardreset??
and did you cid is now screwed up??
alexnvidia said:
ok. i have no idea hoiw i screwed up the bootloader too. this is what happens.
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine.
Click to expand...
Click to collapse
here you needed the sspl to flash official rom
i think that i have this im my tread
then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
Click to expand...
Click to collapse
here you screwed the botloader
now you have an older ipl that does not know how to load the new SPL
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
what should i do now? i really appreciate you/anyone taking the time to look into this issue. thank you.
Click to expand...
Click to collapse
did you try to hard reset?
the two "-" keys and power
???
futureshock said:
have you tryed a hardreset??
and did you cid is now screwed up??
Click to expand...
Click to collapse
yes. i tried hard reset (two soft keys+power then press 0) many times. doesnt work. tried the mtty to format the phone, doesnt work.
here you screwed the botloader
now you have an older ipl that does not know how to load the new SPL
ok, firstly, when i loaded up the SPL1.09, the phone boots up fine. it only got stuck when the flashing to WWE1.38 failed. at this point i still have the new IPL.
the old IPL was flashed in during the recovery attempt when i tried to flash the old official WM5 ROM back hoping it would also downgrade the SPL, but it didnt. it only downgrade the IPL to 0.9. SPL remains 1.09
alexnvidia said:
here you screwed the botloader
now you have an older ipl that does not know how to load the new SPL
ok, firstly, when i loaded up the SPL1.09, the phone boots up fine. it only got stuck when the flashing to WWE1.38 failed. at this point i still have the new IPL.
the old IPL was flashed in during the recovery attempt when i tried to flash the old official WM5 ROM back hoping it would also downgrade the SPL, but it didnt. it only downgrade the IPL to 0.9. SPL remains 1.09
Click to expand...
Click to collapse
im my guide i wrote to use sspl
if you use sspl you finish the 1.34 upgrade from spl 1.09 and is everything fine
if not no
from here you had spl A07 so you could flash ONLY original htc Rus rom
you flashed an older ipl instead
an older ipl that does not load correctly the new spl
the spl can not be downgraded from 1.10(1.09) to 2.05
here is the problem
and as long as you dont have an rom with your CID od HARDSPL the phone can only be flashed using my hermes guide if we find the buton combination on breeze
BR
jerpelea said:
im my guide i wrote to use sspl
if you use sspl you finish the 1.34 upgrade from spl 1.09 and is everything fine
if not no
from here you had spl A07 so you could flash ONLY original htc Rus rom
you flashed an older ipl instead
an older ipl that does not load correctly the new spl
the spl can not be downgraded from 1.10(1.09) to 2.05
here is the problem
and as long as you dont have an rom with your CID od HARDSPL the phone can only be flashed using my hermes guide if we find the buton combination on breeze
BR
Click to expand...
Click to collapse
so what you mean now is my IPL 0.9 is WWE and my SPL is 1.09 Qtek A07? and this is causing the problem? so can i flash the IPL on the phone to the lastest one in tri-colour mode so that it can read the 1.09 SPL? can u please provide me with the SPL upgrade file and utility?
any solutions so far? guys?
alexnvidia said:
so what you mean now is my IPL 0.9 is WWE and my SPL is 1.09 Qtek A07? and this is causing the problem? so can i flash the IPL on the phone to the lastest one in tri-colour mode so that it can read the 1.09 SPL? can u please provide me with the SPL upgrade file and utility?
Click to expand...
Click to collapse
no
your problem is that ipl 0.9 cant load spl 1.09
the memory load address differs and it cant load it correctly
i havent found an solution
you need an valid spl loaded to flash
you can try all the original roms (don't edit them)
and see if any one of them tries to push ipl and spl before actualy flashing
also try the official 1.09 spl flash
BR
nowaday, I found this thread useful. thanks
what happened? I was upgrading to futureshock ver. 4 and during phone'd swiched off ... I was looking for original ROM posted here in Breeze forum, but I didn't find it ... after read this 1st post I recoginze, that Czech ROM official is RUS .. that news for me (of course good ).
KITL Hermes
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried hard reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
I tried KITL Hermes unbrick method but same problems like had others on this forum, I don´t know how to turn my MTeoR to KITL debug mode because device is different like Hermes so key combination doesn´t matches with Breeze. MTTY - info 2 command show me CID: waiting interpreter failed...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
DOPOD601
which RUS update rom can i use?thanks
HTCSDOPOD601in眘HTCE
which rom?
can somebody email to : [email protected] or [email protected] ?
thank you