Upgrade problem with Explode's ROM - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Dear Explode:
i have read all wiki, all guides but no luck to work.
i currently have your R1 installed.
i'm using windows vista ultimate, i can sync normally between laptop and blueangel but i cannot use the upgrade
i have downloaded the OS builder and used the default like you said but when the upgrade tool launches it cannot see the phone (tried both when i put in bootloader mode and when not in bootloader mode)
i get connection error.
when i press on upgrade tool and click next (without bootloader mode on) it can identify current ROM and radio. and when i press next it restarts phone with no progress at all in USB mode.
when i press on upgrade tool and click next (after i put device in bootloader mode) (tried before and after i click) it just gives error 150.
kindly need help.
thx

Read this Thread: http://forum.xda-developers.com/showthread.php?t=291723

I can not support vista because HTC does not support it, the upgrade tools are written to work on windows XP, but you may try to run them with XP compatiblity mode

thx guys i'll give it a try and post back the results

Related

Vista ROM flashing

I have a wierd problem that I haven't seen discusssed here before. My PC runs Vista and has the Windows Mobile Device Center software on it. When I plug the phone in to a USB connection cable to try and flash a new ROM, the phone is recognized. When I start the ROM updater program though, suddenly the phone is "disconnected" (no longer shows as connected and dissappears from the listing of attached devices in My Computer also).
So, the ROM Updater says it cannot find the required file. How can I get the phone to stay connected long enough to run the whole update processs?
Try to put it into bootloader before flashing.
First of all check out the Hermes wiki about Vista flashing.
Second. Try to put your device into botloader mode, then run the flash. This works for me everytime.
Cheers,
Chris
I flash from Vista Ultimate x64 without issue.
NotATreoFan said:
I flash from Vista Ultimate x64 without issue.
Click to expand...
Click to collapse
Same here. However, for ROM flashing I suggest flashing from the SD card. It's safer and quicker. Read up on it here: http://forum.xda-developers.com/showthread.php?t=336158&highlight=flash+sd+card

SOLVED! Bootloaders as far as it goes...Will not load any flash with SSPL or HSPL.

About a year-ish ago windows stopped working on my spv3600 m700 Trinity. I looked into reflashing the phone & put a copy of schaps 4.30 striaght onto the fone no problems.
I now want to upgrade the rom again & can get it into the bootloader screen ok. My problem is that this is as far as I can get. I've even tried the minisd trick but I see loading box very briefly flash up on the screen & thats it...still in bootloader mode with serial but nothing else happens.
The fone is not bricked & if I reset it will load windows. I've tried the original flash & bootloader. Soft (SSPL) & hard Bootloader technique but to no avail.
Has anyone got any other solutions? Many thanks in advance, its sending me crazy!!
Ok I sorted the first problem of using SDcard to flash .MBH files. It was down to the miniSD card format not being FAT32. I reformat the card as FAT32 & then bootloader progressed to installation stage.
...now I have a new problem... i'm stuck in bootloader mode SPL 1.07.0000 IPL 0.50 after I used SSPL from my mobile in windows mode to get the 1.07ds override bootloader. This allowed me to flash the Radio to the latest chinese version. I then used this program again to Flash to windows 6.5 & then half way through it rebooted to the bootloader tricolour screen.
The problem is that now that windows is gone I can only run the standard bootloader SPL 1.07.0000 with the phone. If I try & upgrade a cooked ROM it comes up with an error code on the mobile. If I try an official version it checks the ROM & then says "not allowed".
Is there a way I can change the bootloader through the card SD? I can't either get the bootloader to change from serial msg to usb...doesnt matter how many times I plug in the USB & i'm using XP. Is there a way to force it into USB?
I've tried putting "Des crash proof SPL" ,"Hard SPL", "Hard SPL 1.20" onto SDmini card as TRINIMG.NBH bootloader loads then comes up with 00068002 error i presume on screen
I've tried putting official upgrades "RUU Trinity DOPODA SIA WWE...Ship.EXE rom" & "RUU Trinity HTC WWE .........GPS.exe rom" onto SDmini card as TRINIMG.NBH, bootloader loads, . . .checking, then displays "not allow" & "00028002" on screen! Now i'm really stuck!
Any help would be greatly appreciated!
looks pretty much the same like my trinity right now...
help would be very appreciated
Solved.
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Still on bootloader with error 0068002
can't ran anything.
Please help......
SOLVED:::::::: sorry
Trinity bricked , pls help ...
steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Hi , there ,
I am finding myself into the same situation but I do not realy get you : how You managed to get out of the bootloader mode where it says :
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Can you , pls, be more specific , cause I am a newbe who bricked his Trinity a week ago :::
Blocked with error 0068002
Hello, after I install nAr.23016.FRA.IE8-CHOME on my sfr s300+, I'm blocked on the first page HTC, etc...When I put the S300+ under bootloader (photo and power button action), I plug the USB and I itry to flash;result is a reboot. I try with TRINIMG.NBH and result is error 0068002.
I need help to resolve this problem.Can u help me? Regards.
dan (excuse my bad english)

[Q] Possibly bricked Trinity, help please!!!

Hello!
I have this problem:
I've installed WM6.5 on my Trinity, and it worked well, but today I wanted to try WM6.1 (0.4.9.0 digital) also. The following happened:
Everything worked fine, but at 54% flashing my brother lifted the phone, possibly it lost the USB-contact, because the flasing stopped with an error message (unfortunately can't remember the error number). Since then if I try to flash it with WM6.1 or WM6.5, after 1% the phone resets itself, and the RUU gives a 270 error.
I have the original WM5 ROM also, but if I try installing it, after "Verifying information on your PDA Phone" screen I get a connection error 260.
What can I do???
After the phone resets itself, I can see the HTC logo, and the red letters and numbers, but that's all.
If I try HardSPL, I also get a 260 error.
Can you enter bootloader manualy?
If you can than see SERIAL change to USB when connected to PC it should be OK.
if you have a SD card, you can also try to flash "manualy".
- put your RUU... NBH at the root of the card,
- rename it trinimg.nbh,
- reinsert the card in the phone,
- enter in bootloader (power+cam+reset)
you will have a grey screen asking to push "power", do it and that's it.
if USB is well working, maybe you just need to reflash the hardspooler.
Thank you for your replies.
Fortunately I solved the problem.
I did the following:
1. To be sure, do all the stuff on a Windows XP machine
2. DISABLE "Allow USB Connection" in Active Sync so you see a small red X symbol next to the Active Sync symbol
3. Start the device into Bootloader mode (Cam+Power+Reset) and connect the device to your PC and make sure USB is written on the bottom of your screen (NOT Serial!)
4. Download splxploit (http://forum.xda-developers.com/atta...0&d=1180043588) and execute unlock on your PC
5. Follow the instructions
6. Download HardSPL (http://forum.xda-developers.com/atta...8&d=1185364317) and follow the instructions
7. Finally (to be sure) restart into Bootloader mode and check if SPL is showing "SPL-1.30.Olipro) - if this is the case you've done it !
8. Flash your preferred ROM via miniSD or USB connection
I m glad you solved this. Every day another new way of solving the flash problems.
Hi to All guys
i've got a trinity from my work and it has a custom rom.
I wanted to changed the rom so i download a wm 6.5 and erase the trinity with mtty. After that i try to install the rom with he RUUUupdate, but it get error 270.
Only in that moment i read on the bootloader and see that it haven't olipro or another HARDSPL installed.
So i looked for a solution and i try the unbrick with the splxploit. I did it and i get olipro on the bootloader, but i don't know how go on with install, if i use the exe i get 260 connection error.
Can you help me?

My Head hurts....

I am trying to install 6.5 on my HTC touch HD.
i have looked at the guides, but i am getting nowhere......stuck at 0% on the flashing.
I want to flash Energys rom onto my phone.
Phone is currently
SPL 1.14.000
Radio 1.09.25.14
Rom 1.19.61.1 WWE
what do i need and how do i do it ?
i have downloaded
HSPLWrapper_Blackstone_156OliNex,
SSPL-Manual-TouchHD,
Unsigned_HardSPL_for_Blackstone_OliNex,
Energy.BLACKSTONE.29018.Sense2.5.Cookie.2.0.Apr.18
i have tried on both WinXP and Win 7 Systems, same error 262
1- have you tried installing the htc usb sync drivers manually? -->google
2- do you ever see the tri-color bootloader screen? If not you could try to put it in bootloader manually? you can do that by holding vol down+power button. You do have to turn it of first, and you have to remove the usb cable. WARNING: do not pull out the usb cable while its flashing, you won't be able to start your phone then (you can still flash roms though)
hope this helps
when connecting device to pc does bottom of bootloader (tri colour screen) change from "serial" to usb"? If not you need to either update drivers (see link in Dummies Guide) or open activesync and ensure that "allow usb connections" is enabled in connection settings
If above is all ok then you need to follow guide and get yourself HSPL
If getting stuck at 0% try trouble shooting section and use SSPL
Either way, please post further queries regarding flashing in Dummies Guide thread
Thread closed

HTC HD 7 unable to downgrade spl

hi i m unable to download the spl
device info
HTC hd 7 T9292
Firmware 2250.21.51101.707
Radio software 5.71.09..2a_22.51.50.21u
Radio hardware A.102.0.D4
Bootloader 5.11.2250.0(134400)
i followed the steps give by DFT
i entered the tricolor screen and connected my htrc hd7 but the usb didnt appear at the botton but the qualcom drivers for my phone got nstalled
please help
follow steps by sh4d0w86 ...best instructions.
usb somtimes dosnt show up... been spoken about allready...dont worry about it.
did u download nodo rom with the same region as yours? wont work if you havent
cheers and have a gr8 day
Source: http://forum.xda-developers.com/showthread.php?t=1195647
Launching RSPL
DFT_RSPL_WP7FG1_LAUNCH allows you to load RSPL on the device:
1. Extract ALL files from RAR archive.
2. Run DFT_RSPL_WP7FG1_LAUNCH (with administrative rights to access USB)
3. Mindfully reads information text. Press “Next” button.
4. Reset your device and hold “Volume Down” button during reset to enter OSPL mode.
5. Connect your device to PC via USB cable.
6. Now you may need to install proper USB drivers. They come with Active Sync / Windows Mobile Device Center.
7. Install drivers if required.
8. Make sure device show “USB” at the bottom instead of “Serial”.
9. Press “Next” button in the wizard. It should detect your phone.
10. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
11. After successful connection it should show device codename and allows to choose installed OSPL version.
12. You should look at the screen and select OSPL version in drop down list box. You need do this because it’s not possible to detect installed version via USB.
If your current SPL version doesn't present in the list, you can choose nearest version, BUT ONLY IF IT HAS SAME FIRST NUMBER!!
Example: You have 4.XX on the device. Do NOT choose 1.XX 2.XX 3.XX.
13. Press “Next”. Wait until comes final page.
14. Read and close window.
15. Look at the device – it must reboot to RSPL.
16. If you see RSPLX.Y.Z and “CotullaRSPL” on the screen – the task done! Otherwise, please report in this thread about your problems.
17. Put some feedback in this thread for community and developers.
Installing HSPL
DFT_HSPL_WP7FG1_INSTALL allows you to install HSPL on the device:
1. Launch RSPL on the device like described above.
2. Be sure that you close RSPL wizard window.
3. Run DFT_HSPL_WP7FG1_INSTALL.exe (with administrative rights to access USB).
4. Mindfully reads information text. Press “Next” button.
5. Proper drivers already must be installed in RSPL step.
6. Press “Next” button in the wizard. It should detect your phone.
7. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
8. After successful connection it should show device codename and allows to choose HSPL or OSPL version to install. OSPL means you install stock SPL back.
9. Check device codename, if something wrong turn off computer and run to the nearest forest. Grab some water with yourself.
10. Press “Next”. Wait until comes final page.
11. Device will reboot and start to boot OS.
12. Reset it and enter SPL mode again. Be sure there HSPLX.Y.Z and “CotullaHSPL” appear.
13. Put some feedback in this thread for community and developers.
hi tclong
why would you put all that up?
its wrong!
vithichuvan has bootloader 5.11... which means what you have just told vithichuvan to do wont work
he has to downgrade first and then follow those instructions
cheers and have a gr8 day
jhonny said:
hi tclong
why would you put all that up?
its wrong!
vithichuvan has bootloader 5.11... which means what you have just told vithichuvan to do wont work
he has to downgrade first and then follow those instructions
cheers and have a gr8 day
Click to expand...
Click to collapse
sorry my bad overlooked bootloader 5.11
so vithichuvan should follow this
http://forum.xda-developers.com/showthread.php?t=1295068
Yup..it is better to do a Y cable image.. zune backup sucks anyway, I have yet to hear from anyone that has sucessfully reverted bootloader via Zune backup
Did anyone come out with an HSPL/RSPL for HTC HD7
bootloader version:
5.10.2250.0 (132968); PD29110
thanks
@Santa
Follow tclong's link in post #5...if Bootloader version is 5.xx
please help
friends I following the steps given in http://forum.xda-developers.com/showthread.php?t=1597837
SCHUIMG.nbh for Schubert (HD 7)
Rom-download: http://forum.xda-developers.com/showthread.php?t=1427890 NOT WORKING
AND THIS TOO NOT WORKING
http://click.xda-developers.com/api...d/or custom wires! - xda-developers&txt=http:
%2F%2Ful.to%2Fulcjku60&jsonp=vglnk_jsonp_13771504910138
Ii downloaded the rom from http://forum.xda-developers.com/wiki/HTC_HD7/Shipped_Roms
downloaded this Asia WWE 1.57.707.02 HTC HD7 T9292 7.0.7004.0 2250.09.15702.707 5.52.09.16_22.33a.50.10U 1.57.2250.0(113571) and remaned to SCHUIMG.nbh
and formatted the 2gb sd card to fat32 and copied the SCHUIMG.nbh and entered the usb host mode and my phone says Loading.... and I can see lights in my card reader image attached
please help
I think my phone is already half bricked

Categories

Resources