Database Develop

P3600i Flashing Problems

Hi
I am following the guides at
http://trinityguides.info/index.php?option=com_content&task=view&id=25&Itemid=66
and
http://forum.xda-developers.com/showthread.php?t=399827
Now I downloaded HardSPL 1.20 mentioned at
http://trinityguides.info/index.php?option=com_content&task=view&id=25&Itemid=66
and also tried the one at http://www.mediafire.com/?yxz2pu1oytg
I have installed USB driver on VISTA as per guide. my Bootloader shows USB.
But whenever I try to install either of the SPL it gives me an error
ERROR [270]: UPDATE ERROR
The image file is corrupted. Please check your Update Utility
Click to expand...
Click to collapse
Please help me with this

Ok Fixed problem
Perfect solution here
http://forum.xda-developers.com/showpost.php?p=2298295&postcount=6
Connect to your PC and make sure activesync has run properly and your phone is on.
Open Hard SPL and run the ROMupdate. Your phone will go to tricolour and it will come up with a communication error.
disconnect from PC but leave the phone in tricolour....DO NOT reset it.
Cancel our of the ROMupdate. connect the phone to the pc again and run ROMupdate again.
This time it will go all the way through and you will have HardSPL on your phone.
Check it by entering bootloader and it should show Olipro 3.2.
You can then flash away....make sure you always put the phone into bootloader before flashing.
Click to expand...
Click to collapse
Flashing now and will update soon

Big Problem with Diamond

Hi,
i've a big problem with my diamond
it starts normally, but after htc splash screen, it tries to load windows but after 1-2 seconds it restart.
i was using cooked rom gen.Y D2 rev.Y with radio 1.09.25.23
G 52.51.25.26H
i've tried with original rom 2.03 but the problem still remains.
What can i do to resolve this problem?
Where can i find original radio and G (what does it stand for?) to put inside my htc with original rom for probably warranty assistence (i hope)
i've also olinex1.40 spl, how can i remove it?
Thank you in advance
Gianluca

SOunds like a bad flash to me. Try using MTTY to reflash. Should work fine
http://forum.xda-developers.com/showthread.php?t=540290

how can i run this procedure:
Connect Device to PC via Active Sync, Once Connected Uncheck USB Connections,DISCONNECT DEVICE then Reboot Computer
if the device can't start completely?

Flash from your System not the Internal Storage. Read the 4th post.

i can't install drivers on my win7 x64 because i can't follow the first post "how to install drivers" so with the mtty.exe it doesn't find the usb driver

In that case see if you can get into bootloader.
(Reset + Hold Vol Down), this will show the Red, Blue, Green screen showing "Serial"
Then plug your usb cable in and you should get it showing "USB".
You then need to Hard SPL and reflash.

yes i've succesfully installed drive on win7 x64
i've run mtty.exe, followed the instructions, all ok.
then i've disconnected the diamond from usb and made an hard reset (it says press vol.up to restore manufacturer default, vol. down to restore and format movinanand, i press vol. up, and after vol.up again: is it the hard reset or is it another menu?)
but after restart the htc has same problem..it continues to restart by itself

i've decided to return htc to stock software and firmware in order to send him in warranty to delaer.
so, i've installed last official rom htc 2.03, it includes the radio.
Now after that, because system doesn't want to start completely, also after mtty.exe format ecc., the last thing i've to do is install official spl right?
i've found the guide:
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
1. download the stock spl package from this post (pick one of the attachments) in this thread.
2. also download the RUU-SSPL-withoutNBH.zip from the attachments in this post.
3. pick the SPL you want to reflash to (ONLY FOR WARRANTY REASONS), it's a .NBH file, put the NBH in the extracted RUU-SSPL-withoutNBH package.
4. run the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to black screen), it goes to 100%, reboots, done.
+5. to verify, volume down + reset, see version number on tricolour screen.
that's it.
what official spl have i to install? 1.23 1.34 1.37?

i've tried with all the 3 spl but nothing changed i think, because when i open the bootloader it still saying 1.40olinex

Need Help Please With My HTC P3600 Hardspl error (260)

Hi, i would like to somebody helps me, i got my htc recently and i can't do it a hardspl i do all the steps and when it comes to almost finish gave an error i've tried with many different hardspl and nothing, i will show you the erros that gaves me... please help me with this problem, cause i can't do anything to my htc...

Hi
I have the some problem, I have follow this guide :
Step 2 - Upgrade to Hard SPL
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Before you proceed, check which SPL is on your device. Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If your SPL is 3.20.Olipro then you already have Hard-SPL on your device and can skip this step and proceed to upgrade your ROM or radio.
1. Download the Hard-SPL for P3600i (do NOT use any of the Hard-SPL's for Trinity/DoPod)
* Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
2. Unzip the Files, and click on ‘ROMUpdateUtility.exe’
Image Missing
3. Check the checkbox, and click ‘next’
Image Missing
4. Follow the directions in the window, and establish an activesync connection with your device
* Make sure the activesync icon is be green (finished synchronizing)
* Make sure your battery is charged
Image Missing
5. Check the checkbox, click ‘next’
Image Missing
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
Image Missing
7. After the version number has appeared, click next
Image Missing
8. In the following window, click ‘next’
after you click this, the flash will begin, so do not disconnect your device or do anything stupid on your computer
Image Missing
!NOTE! (quoted straight from Jon's post on first page)
WHEN FLASHING HARDSPL, IT WON'T WORK THE FIRST TIME - YOU WILL GET AN ERROR (CODE 260). THIS IS EXPECTED.
Quote:
Originally Posted by joncgde2
This is what happens.
You go to flash HardSPL like the guide says. LOOK AT THE SCREEN ON YOUR PHONE, YOU MIGHT HAVE SECURITY PERMISSIONS AND NEED TO MANUALLY ALLOW THE PROGRAMS TO RUN.
It looks like it's about to flash and then errors. BUT your phone is on the 3-colour bootloader screen! How odd. Well KEEP YOUR PHONE ON THE BOOTLOADER SCREEN, and unplug it from your computer. Exit the HardSPL program, RUN IT AGAIN, and FLASH THE PHONE AGAIN WITH HARDSPL (obviously connect your phone and stuff back to your PC).
The point here is this: the first time it will fail, but at least manage to get the bootloader up. With this bootloader up, exit the flashing program, restart it, and then you should be able to run the flashing program and have it complete.
DOUBLE CHECK YOUR PHONE HAS THE OLIPRO HARDSPL INSTALLED after completion, by soft-resetting (hold the power and camera buttons at the same time AND use the stylus to press the putton at the bottom of the phone. You might not get it the first time, but with practice you'll get the hang of it).
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated.
Image Missing
Image Missing
10. Once your device is finished updating, it will automatically soft reset. Click the ‘Finish’ button to exit the RUU program.
Image Missing
To confirm is Hard-SPL is on your device, manually enter Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If successful you will see the tri-colour screen and the following will be displayed
Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
but also after restart a lot of time HARDSPLromupdateutility.exe, I still have the same problem!
anybody may help me?

Now I have stratos image,
maybe is this the problem?

Hi
Pls I need help, I tried to upgrade my HTC P3600 then my computer crash so now every time I try to start my phone all what I got is a picture (HTC start mobility) and then nothing.
Pls help me.
Thanks

Hi gys, I think that this is my first post, but I want to share some solution for with you. The most important think with "connection" errors is to have HSPL installed correctly. I was trying to install on my HD2 universal ones, like Hard spl v7 and 9, but problems occured. So after trying everything, I found HSPL (on this forum) just for HD2. After that, everything wass like a charm

Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior

base167 said:
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
Click to expand...
Click to collapse
You have choice a wrong HardSPL !!!
Olipro 3.10 and 3.20 are for HTC P3600i and no working for TRINITY P3600.
So, now probabily you don't see "USB" on Bootloader when you connect you trinity on PPC.
Solution:
You must reload your H-SPL With SD CArd.
It's very simple:
searching for a Hard SPL for trinity device, example Olipro 1.20 and rename file "RUU_signed.nbh" ---> "TRINIMG.nbh".
Then copy file "TRINIMG.nbh" in a SD CARD and insert it on your Trinity; After that , make a Soft reset with stylus reset +power+camera.
Power bottom for update your Bootloader.
Now you would see your trinity working again
Davide

SOLVED! Bootloaders as far as it goes...Will not load any flash with SSPL or HSPL.

About a year-ish ago windows stopped working on my spv3600 m700 Trinity. I looked into reflashing the phone & put a copy of schaps 4.30 striaght onto the fone no problems.
I now want to upgrade the rom again & can get it into the bootloader screen ok. My problem is that this is as far as I can get. I've even tried the minisd trick but I see loading box very briefly flash up on the screen & thats it...still in bootloader mode with serial but nothing else happens.
The fone is not bricked & if I reset it will load windows. I've tried the original flash & bootloader. Soft (SSPL) & hard Bootloader technique but to no avail.
Has anyone got any other solutions? Many thanks in advance, its sending me crazy!!

Ok I sorted the first problem of using SDcard to flash .MBH files. It was down to the miniSD card format not being FAT32. I reformat the card as FAT32 & then bootloader progressed to installation stage.
...now I have a new problem... i'm stuck in bootloader mode SPL 1.07.0000 IPL 0.50 after I used SSPL from my mobile in windows mode to get the 1.07ds override bootloader. This allowed me to flash the Radio to the latest chinese version. I then used this program again to Flash to windows 6.5 & then half way through it rebooted to the bootloader tricolour screen.
The problem is that now that windows is gone I can only run the standard bootloader SPL 1.07.0000 with the phone. If I try & upgrade a cooked ROM it comes up with an error code on the mobile. If I try an official version it checks the ROM & then says "not allowed".
Is there a way I can change the bootloader through the card SD? I can't either get the bootloader to change from serial msg to usb...doesnt matter how many times I plug in the USB & i'm using XP. Is there a way to force it into USB?
I've tried putting "Des crash proof SPL" ,"Hard SPL", "Hard SPL 1.20" onto SDmini card as TRINIMG.NBH bootloader loads then comes up with 00068002 error i presume on screen
I've tried putting official upgrades "RUU Trinity DOPODA SIA WWE...Ship.EXE rom" & "RUU Trinity HTC WWE .........GPS.exe rom" onto SDmini card as TRINIMG.NBH, bootloader loads, . . .checking, then displays "not allow" & "00028002" on screen! Now i'm really stuck!
Any help would be greatly appreciated!

looks pretty much the same like my trinity right now...
help would be very appreciated

Solved.
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.

steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Still on bootloader with error 0068002
can't ran anything.
Please help......
SOLVED:::::::: sorry

Trinity bricked , pls help ...
steve54321 said:
Finally worked out why my phone would not change from serial to usb on the bootloader screen. Its all down to the power from usb lead...luckily I have a double usb lead which I use for an external hard drive. Two usbs plugged into my laptop provides twice the current...as soon as I used this lead tadaaa, the phone comes on & is recognised by windows xp even when its in bootloader mode. If you don't have a lead try using a different computer...just incase the usb output is crap!
From here I then ran the unbrick / exploit program which you have to run two/three times but then this will put the phone into a bootloader which allows you to flash the phone with any ROM.
Hope this info is of any help.
Click to expand...
Click to collapse
Hi , there ,
I am finding myself into the same situation but I do not realy get you : how You managed to get out of the bootloader mode where it says :
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
Can you , pls, be more specific , cause I am a newbe who bricked his Trinity a week ago :::

Blocked with error 0068002
Hello, after I install nAr.23016.FRA.IE8-CHOME on my sfr s300+, I'm blocked on the first page HTC, etc...When I put the S300+ under bootloader (photo and power button action), I plug the USB and I itry to flash;result is a reboot. I try with TRINIMG.NBH and result is error 0068002.
I need help to resolve this problem.Can u help me? Regards.
dan (excuse my bad english)

error 262 update error

I have T-Mobile touch pro2,when i m instaling the hard-spl,i have the error 262 update error.

Doing a quick search for this error I found 20+ threads with the answer to your problem. I would be nice and give you the solution but it does not look like you even tried searching.
Some tips:
1. this issue does not only occur on your device but others too (ie. search all threads not just the Rhodium thread).
2. never state that you are new to a device or topic, and explain what you have done to help find or try to resolve your issue. Other wise you will not be treated with proper respect and will never get a good answer.
There are more tips than just the above two for any forum (not just this one) that will get your answers in no time at all.

I did all what you said,but no help plz help me.

I tried "Search this forum" and so forth, and couldn't find anything either. But if you click on the "Search" button at the top (next to "QuickLinks") then you can search all the forums with Google, and that seems to work a lot better. You will find a lot of results if you search for "error 262", with several people seeming to report that removing and reinstalling ActiveSync worked for them.

I tried more than 2 computer.

At which point in the HardSPL process did this happen?
1) download newest Hard-SPL package from Rhodium-HardSPL_V2_00R3_185HSPL.zip attachment, extract to an empty folder.
2) you must Have Phone Synced with PC in Windows Mobile!!! I mean it has to be connected to activesync or WMDC via USB cable. and it must not be in Flight/Airplane mode (i.e. radio should be on).
3) NEW: internet access is required as the program checks online for updates and license.
4) run Rhodium-HardSPL_V2_00R3.exe on PC, make sure it's launched from a local drive (not through network drive, etc.). XP requires Admin logon, and Vista/Windows 7 will automatically prompt to allow it to run in Admin mode, allow it please. if you get an antivirus warning, please ignore it, it contains no harmful code (just used a packer to compress it).
5) follow steps as prompted in the Hard-SPL program. if this is the first run of Hard-SPL on a device after hard reset, you must select Automatic flash mode (the first button in Welcome screen).
notes: you should usually go for Automatic flash mode; the Manual flash option is only to be used as noted below and you must only attempt the Manual mode option if Automatic flash mode or SSPL-Manual.exe already put device in black screen. any other errors triggered while running in Autoflash mode will have to be fixed as instructed in the error message.
6) it will ask you to wait while it prepares for the flashing, press OK.
7) now it should go through without any error messages, if one does pop up, then please follow the instructions included in the error text. if no specific instruction is shown, then ask for help in the thread, but this should not ever occur (as this means a really fatal error occurred).
8) at this point the device did hopefully went to a black screen (reporting version as 1.10.C-SSPL only using "info 7" in mtty), this is the SSPL version, which is temporary. then RUU will instantly launch.
9) some notes: when RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
10) SPL flashes, device automatically reboots, job done.
11) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.85.OliNex, which is the Hard-SPL version.

Update Error on second TP2
I have two Verizon HTC TP2. One of them i have flashed the rom multiple times from my computer. It currently has the November 27 release of the Energy rom.
I went to go put that same Energy Rom on the other phone and every time i try to flash it i get a 262 error.
It is correctly connected to active sync. The phone that won't flash currently has the standard Windows Mobile 6.1 installed on it that came from Verizon.
I have also tried different roms as well none of them seem to work, it goes through the process of trying to upgrade, gets past the 4 colored screen to the progress bar and at 0% it throws the 262 error.
I have tried to run RhodiumW-HardSPL_V1_10R3 on my computer multiple times but i don't think the problem is with my computer given that i can flash my other phone easily.
If anyone has any suggestions or tips that would be great. I am pounding my head against a wall on this one.
A couple other things to note: radio is on when i try to flash, i have left the sim card in, i have also tried adjusting the connection settings on the phone for active sync such as turning off "enable faster data synchronization" with no luck.

HI
You can't HARD SPL more than one device, otherwise you have to give a drink to the developers, about 4.5€ to let the hard spl works on a second phone.

I have tow phones,in the first one i was using the hard-spl a lot of times and in the scened one i got the error 262 update error.I tank if the problem it was about the developers donation,i could not hard-spl my first phone many times?

unable to hardspl tp2
ScooterG said:
At which point in the HardSPL process did this happen?
1) download newest Hard-SPL package from Rhodium-HardSPL_V2_00R3_185HSPL.zip attachment, extract to an empty folder.
2) you must Have Phone Synced with PC in Windows Mobile!!! I mean it has to be connected to activesync or WMDC via USB cable. and it must not be in Flight/Airplane mode (i.e. radio should be on).
3) NEW: internet access is required as the program checks online for updates and license.
4) run Rhodium-HardSPL_V2_00R3.exe on PC, make sure it's launched from a local drive (not through network drive, etc.). XP requires Admin logon, and Vista/Windows 7 will automatically prompt to allow it to run in Admin mode, allow it please. if you get an antivirus warning, please ignore it, it contains no harmful code (just used a packer to compress it).
5) follow steps as prompted in the Hard-SPL program. if this is the first run of Hard-SPL on a device after hard reset, you must select Automatic flash mode (the first button in Welcome screen).
notes: you should usually go for Automatic flash mode; the Manual flash option is only to be used as noted below and you must only attempt the Manual mode option if Automatic flash mode or SSPL-Manual.exe already put device in black screen. any other errors triggered while running in Autoflash mode will have to be fixed as instructed in the error message.
6) it will ask you to wait while it prepares for the flashing, press OK.
7) now it should go through without any error messages, if one does pop up, then please follow the instructions included in the error text. if no specific instruction is shown, then ask for help in the thread, but this should not ever occur (as this means a really fatal error occurred).
8) at this point the device did hopefully went to a black screen (reporting version as 1.10.C-SSPL only using "info 7" in mtty), this is the SSPL version, which is temporary. then RUU will instantly launch.
9) some notes: when RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
10) SPL flashes, device automatically reboots, job done.
11) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 0.85.OliNex, which is the Hard-SPL version.
Click to expand...
Click to collapse
got error after 10mins and 0%
ps i gave the 4ec donatation and have not been able to flash still

jrange1 said:
got error after 10mins and 0%
ps i gave the 4ec donatation and have not been able to flash still
Click to expand...
Click to collapse
You need to post in the HardSPL thread on this

Please post your question on the Hard-SPL thread.
However, what you have been told is correct, you can only flash one phone per Hard-SPL license. If you want to flash more than one, you have to contact the author OliNex and get a second license. Sending him a donation will not automatically get it for you.
Thread Closed.
Russ