Big Problem with Diamond - Touch Diamond, MDA Compact IV General

Hi,
i've a big problem with my diamond
it starts normally, but after htc splash screen, it tries to load windows but after 1-2 seconds it restart.
i was using cooked rom gen.Y D2 rev.Y with radio 1.09.25.23
G 52.51.25.26H
i've tried with original rom 2.03 but the problem still remains.
What can i do to resolve this problem?
Where can i find original radio and G (what does it stand for?) to put inside my htc with original rom for probably warranty assistence (i hope)
i've also olinex1.40 spl, how can i remove it?
Thank you in advance
Gianluca

SOunds like a bad flash to me. Try using MTTY to reflash. Should work fine
http://forum.xda-developers.com/showthread.php?t=540290

how can i run this procedure:
Connect Device to PC via Active Sync, Once Connected Uncheck USB Connections,DISCONNECT DEVICE then Reboot Computer
if the device can't start completely?

Flash from your System not the Internal Storage. Read the 4th post.

i can't install drivers on my win7 x64 because i can't follow the first post "how to install drivers" so with the mtty.exe it doesn't find the usb driver

In that case see if you can get into bootloader.
(Reset + Hold Vol Down), this will show the Red, Blue, Green screen showing "Serial"
Then plug your usb cable in and you should get it showing "USB".
You then need to Hard SPL and reflash.

yes i've succesfully installed drive on win7 x64
i've run mtty.exe, followed the instructions, all ok.
then i've disconnected the diamond from usb and made an hard reset (it says press vol.up to restore manufacturer default, vol. down to restore and format movinanand, i press vol. up, and after vol.up again: is it the hard reset or is it another menu?)
but after restart the htc has same problem..it continues to restart by itself

i've decided to return htc to stock software and firmware in order to send him in warranty to delaer.
so, i've installed last official rom htc 2.03, it includes the radio.
Now after that, because system doesn't want to start completely, also after mtty.exe format ecc., the last thing i've to do is install official spl right?
i've found the guide:
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
1. download the stock spl package from this post (pick one of the attachments) in this thread.
2. also download the RUU-SSPL-withoutNBH.zip from the attachments in this post.
3. pick the SPL you want to reflash to (ONLY FOR WARRANTY REASONS), it's a .NBH file, put the NBH in the extracted RUU-SSPL-withoutNBH package.
4. run the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to black screen), it goes to 100%, reboots, done.
+5. to verify, volume down + reset, see version number on tricolour screen.
that's it.
what official spl have i to install? 1.23 1.34 1.37?

i've tried with all the 3 spl but nothing changed i think, because when i open the bootloader it still saying 1.40olinex

Related

[TUT] Dummies guide: flashing 1.56+ roms [v 2.0] - [HSPL][USPL]

First of all you will need .NET installed if you do not have it already. I would recommend .NET 3.5. You can download it from Microsoft here.
The most important part about flashing a rom is knowing what SPL version your phone has and what rom you want to use before you begin flashing. If you are at a point where you have already begun flashing and are now getting a green, distorted screen, having huge issues with the phone not responding and airplane mode being stuck on, that is because you have done the process wrong. Don't fret, you can simply start over with this guide. You can still place your phone into the bootloader so you are ok.
The first thing to do is check what your SPL version currently is. To do this you need to enter bootloader by:
Turn it off.
Hold the volume down button while you press the power on button.
You should see a tri-color screen with some text (This is bootloader).
Plug in your phone to your computer via USB. At the very bottom of the screen it should show USB.
Once you know what your SPL version currently is you need to decide whether you want to use USPL or HSPL to flash roms.
The difference between USPL and HSPL:
HSPL is an user-modified SPL that you have to flash to your phone. It overwrites the existing SPL on your device with a "hacked" one so to say. It allows you to bypass the HTC certificate check and flash unsigned or CID-mismatching roms to your phone. You only have to flash it once and then you can flash roms anytime.
USPL is a temporary solution. It takes advantage of an exploit in the existing SPL and then loads a modified one to memory, effectively allowing the same thing as HSPL. However, since this is only memory-resident you have to do it each time you want to flash unsigned or CID-mismatching roms to your phone, because this exploited state is lost upon reboot. With USPL you must still have the right version of the HTC SPL that is compatible with the rom you want to use.
Now that you have decided which route you want to go as far as SPL's go, temporarily disable or uninstall your virus scanning software as 90% of them will conflict with flashing.
If you wish to use HSPL and it shows your current SPL as:
Anything but 1.56.OliNex - go to step (HSPL1) on post 2
1.56.OliNex - go to step (HSPL4) on post 2
If you wish to use USPL and it shows your current SPL as:
Anything but 1.54.0000 - go to step (USPL1) on post 3
1.54.0000 - go to step (USPL5) on post 3
If you are getting errors during the RUU process, read this guide for descriptions of the error codes and associated solutions/suggestions!
If you need to update your USB drivers, read this guide for step-by-step instructions!
MOD EDIT (01/10/09)
Video guide to help newbies out with loading ROMs
HSPL Method
Use this method only if you selected the HSPL route from the first post!
HSPL1 - Downloads
(HSPL1a) HSPLWrapper_Blackstone_156OliNex.zip
(HSPL1b) A 1.56+ based rom - Your end result rom, i.e. rom you want on device which is based on 1.56+
(HSPL1c) BlackstoneRUUWrapper.zip
(HSPL1d) SSPL-Manual-TouchHD.zip
(HSPL1e) Extract each item to its own folder
HSPL2 - Flash new SPL (1.56.OliNex)
(HSPL2a) Place your phone into its bootloader.
(HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
(HSPL2c) If successful, go to step HSPL3. If the flashing process sits at 0% and you get Error [260] connection after some time, go to step (Troubleshooting).
HSPL3 - Check SPL version
(HSPL3a) Place your phone into its bootloader.
(HSPL3b) When the bootloader appears it should show SPL v 1.56.OliNex. If it does go to step (HSPL4). If it does not something happened so repeat step (HSPL2).
HSPL4 - Flash new 1.56+ rom
(HSPL4a) Place your phone into its bootloader.
(HSPL4b) If the rom you downloaded from step (HSPL1b) does not include BlackstoneRUUWrapper.exe then use the download from step (HSPL1c). Make sure the .nbh file from step (HSPL1b) and BlackstoneRUUWrapper.exe are in the same folder.
(HSPL4c) Run BlackstoneRUUWrapper.exe and follow it as normal.
(HSPL4d) Hard reset afterwards. Once or twice- up to you. Twice has been recommended. Turn off your phone. I personally do it right after flashing completes and I see the "Smart Mobility" screen. I just yank the battery out instead of waiting for it to boot up all the way and go through customization process just to hard reset Hold the volume down button and volume up button while you press the power on button. You should see a message saying "This operation will delete all your personal data, and reset all settings to the manufacturer default settings. Press VolUp to restore manufacturer defaults, or press other keys to cancel." Do exactly what it says...
You are done!
Troubleshooting - manual SSPL
Boot up your phone.
Copy SSPL-Manual-TouchHD.exe to your phone. In a file browser on your phone browse to where you copied SSPL-Manual-TouchHD.exe and run it.
Your phone will reboot into its bootloader and should show SPL v 1.07.OliNex.
When it shows USB at the bottom then run HSPLWrapper_blackstone_156OilNex.exe from your computer again.
Go to step HSPL3 if successful.
USPL Method
Use this method only if you selected the USPL route from the first post!
USPL1 - Downloads
(USPL1a) RUU_Signed_Blackstone_stockSPL154.zip
(USPL1b) HSPLWrapper_Blackstone_156OliNex.zip
(USPL1c) USPL GUI v 2.5.zip
(USPL1d) A 1.56+ based rom - Your end result rom, i.e. rom you want on device which is based on 1.56+
(USPL1e) BlackstoneRUUWrapper.zip
(USPL1f) Extract each item to its own folder
USPL2 - Updating HTC USB Sync driver
(USPL2a) Follow my guide here on updating the HTC USB Sync driver.
USPL3 - Flash new SPL (1.54.0000)
(USPL3a) Place your phone into its bootloader.
(USPL3b) Run USPL.exe from the download in step (USPL1c). Remember to disable your antivirus for this. Some provide a false positive that it is a virus/trojan. When the application appears click on Run USPL.
(USPL3c) Your phone should reboot and return to its bootloader but saying SPL v 1.15.USPL and USB at the bottom. If it does not show USB after some time, disconnect and reconnect the USB cable from your phone.
(USPL3d) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (USPL1b). Do not click any buttons on the screen when the application appears.
(USPL3e) Copy RUU_Signed.nbh that you extracted from the download in step (USPL1a) and overwrite the one in the directory where you ran HSPLWrapper_Blackstone_156OliNex.exe from. If you get an error message saying that the file is already in use that is because you clicked one or more buttons in the HardSPL application window once it appeared. If that happens to you, exit from it, start it again, and DO NOT CLICK ANYTHING YET.
(USPL3f) Now you can continue in the HardSPL application and follow it as normal. Basically what you are doing is flashing the stock 1.54.0000 SPL to your phone by overwriting the HardSPL's .NBH file with the stock one.
USPL 4 - Check SPL version
(USPL4a) Place your phone into its bootloader.
(USPL4b) When the bootloader appears it should show SPL v 1.54.0000. If it does go to step (USPL5). If it does not something happened so repeat step (USPL3).
USPL 5 - Flash new 1.56+ rom
(USPL5a) Place your phone into its bootloader.
(USPL5b) Run USPL.exe from the download in step (USPL1c). Remember to disable your antivirus for this. Some provide a false positive that it is a virus/trojan. When the application appears click on Run USPL.
(USPL5c) Your phone should reboot and return to its bootloader but saying SPL v 1.15.USPL and USB at the bottom. If it does not show USB after some time, disconnect and reconnect the USB cable from your phone.
(USPL5d) If the rom you downloaded from step (USPL1d) does not include BlackstoneRUUWrapper.exe then use the download from step (USPL1e). Make sure the .nbh file from step (USPL1d) and BlackstoneRUUWrapper.exe are in the same folder.
(USPL5e) Run BlackstoneRUUWrapper.exe and follow it as normal.
(USPL5f) Hard reset afterwards. Once or twice- up to you. Twice has been recommended. Turn off your phone. I personally do it right after flashing completes and I see the "Smart Mobility" screen. I just yank the battery out instead of waiting for it to boot up all the way and go through customization process just to hard reset Hold the volume down button and volume up button while you press the power on button. You should see a message saying "This operation will delete all your personal data, and reset all settings to the manufacturer default settings. Press VolUp to restore manufacturer defaults, or press other keys to cancel." Do exactly what it says...
You are done!
Dude, this is tight!!! Awesome Yo!
Loveleh!
I am so frustrated!!!!!!!!! I have followed these instructions to a T, and I still get an error when trying to flash to 2.8. I keep getting the error: [240] File Open.
Can someone please help me???
Thanks!
You've been a busy boy!!!
Excellent post mate, was getting sick of posting this process myself. Now all I have to do is direct them all here, or to the wiki
Awesome stuff. I wish this was around the other night when I spent hours and hours reading and reading before finally sorting it out.
I failed at your step 7 however as I think it was 2am and I was passing out in front of the PC whilst rebooting and hard resetting over and over. Beer tonight then!
Cheers
This guide totally saved my life (A.K.A phone).
Thank you very much.
Wow... excellent mate!
Thanks!
Thanks for this great work.
Unfortunately Im stuck at step 5d
USB connection in Activesync mode is off.
My phone is in bootloader, "Serial" change to "USB" aswell
However when I launch blac_uspl.exe in command prompt (in windows XP) I have the following error : D:\Mes documents\Downloads\uspl_2.5>blac_uspl
HTC Blackstone USPL version 2.5, Apr 5 2009
Opening USB port \\?\usb#vid_0bb4&pid_00ce#5&381252ce&0&1#{25dbce51-6c8f-4a72-8a
6d-b54c2b4fc835}...
ERROR: USB port could not be opened!
Verify that device is connected and SPL boot mode is active,
disallow USB connections in ActiveSync settings and try again.
If I need to install "vista usb drivers", please kindlly state how to.. in XP as the folder c:\winnt\inf contains .inf & .cat files.
Thnx a lot.
Multani004 said:
Thanks for this great work.
Unfortunately Im stuck at step 5d
USB connection in Activesync mode is off.
My phone is in bootloader, "Serial" change to "USB" aswell
However when I launch blac_uspl.exe in command prompt (in windows XP) I have the following error : D:\Mes documents\Downloads\uspl_2.5>blac_uspl
HTC Blackstone USPL version 2.5, Apr 5 2009
Opening USB port \\?\usb#vid_0bb4&pid_00ce#5&381252ce&0&1#{25dbce51-6c8f-4a72-8a
6d-b54c2b4fc835}...
ERROR: USB port could not be opened!
Verify that device is connected and SPL boot mode is active,
disallow USB connections in ActiveSync settings and try again.
If I need to install "vista usb drivers", please kindlly state how to.. in XP as the folder contains .inf & .cat files.
Thnx a lot.
Click to expand...
Click to collapse
Yes, download the USB drivers from above and extract them to a folder. Mind where you extract them. Follow these steps:
(1) Start -> Run -> devmgmt.msc
(2) Look for HTC USB Sync
(3) Double-click it and click the Driver tab
(4) Click Update Driver
(5) On new screen tell it not to use Windows Update
(6) Install from a specified location
(7) Check only box that says "Include this location in the search"
(8) Click Browse and locate the extracted drivers you downloaded
(9) After selecting click next and select the new driver
(10) After it is updated reboot and try USPL again
Let me know how it works.
damian.r.smith said:
Awesome stuff. I wish this was around the other night when I spent hours and hours reading and reading before finally sorting it out.
I failed at your step 7 however as I think it was 2am and I was passing out in front of the PC whilst rebooting and hard resetting over and over. Beer tonight then!
Cheers
Click to expand...
Click to collapse
LOL, good deal!
pierce97 said:
I am so frustrated!!!!!!!!! I have followed these instructions to a T, and I still get an error when trying to flash to 2.8. I keep getting the error: [240] File Open.
Can someone please help me???
Thanks!
Click to expand...
Click to collapse
What is giving you this message? The RUU? What step are you at in my guide? Do you get USPL run successfully? Does your bootloader on your phone show 1.15.USPL and USB when it's connected to your computer?
Keep up the good work bro and you'll be a MOD soon enough!!!
Fallen Spartan said:
Keep up the good work bro and you'll be a MOD soon enough!!!
Click to expand...
Click to collapse
haha... that's a big job on this forum!
Thanks for the quick reply.
Up to step 5, everything is ok.
but It wont let me update saying its impossible to update the drivers.
1 more thing i want to mention is that i found those inf & cat files already present in c:\winnt\inf folder. ofcourse the size is not the same.
I will try to update the drivers again though Im starting to assume that my windows dont see a different between already present files and new extracted files.
Multani004 said:
Thanks for the quick reply.
Up to step 5, everything is ok.
but It wont let me update saying its impossible to update the drivers.
1 more thing i want to mention is that i found those inf & cat files already present in c:\winnt\inf folder. ofcourse the size is not the same.
I will try to update the drivers again though Im starting to assume that my windows dont see a different between already present files and new extracted files.
Click to expand...
Click to collapse
You can force Windows to accept the new driver files. You just have to tell it that you "Have Disk" and locate those files. Once you do it will show a dialog where you can select the device and it should overwrite your current driver with the one from the download.
Good picture step-by-step guide for updating drivers can be found here
Fallen Spartan said:
Good picture step-by-step guide for updating drivers can be found here
Click to expand...
Click to collapse
Nice, I'm going to edit that into my guide instead of my half-assed directions

Need Help Please With My HTC P3600 Hardspl error (260)

Hi, i would like to somebody helps me, i got my htc recently and i can't do it a hardspl i do all the steps and when it comes to almost finish gave an error i've tried with many different hardspl and nothing, i will show you the erros that gaves me... please help me with this problem, cause i can't do anything to my htc...
Hi
I have the some problem, I have follow this guide :
Step 2 - Upgrade to Hard SPL
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Before you proceed, check which SPL is on your device. Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If your SPL is 3.20.Olipro then you already have Hard-SPL on your device and can skip this step and proceed to upgrade your ROM or radio.
1. Download the Hard-SPL for P3600i (do NOT use any of the Hard-SPL's for Trinity/DoPod)
* Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
2. Unzip the Files, and click on ‘ROMUpdateUtility.exe’
Image Missing
3. Check the checkbox, and click ‘next’
Image Missing
4. Follow the directions in the window, and establish an activesync connection with your device
* Make sure the activesync icon is be green (finished synchronizing)
* Make sure your battery is charged
Image Missing
5. Check the checkbox, click ‘next’
Image Missing
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
Image Missing
7. After the version number has appeared, click next
Image Missing
8. In the following window, click ‘next’
after you click this, the flash will begin, so do not disconnect your device or do anything stupid on your computer
Image Missing
!NOTE! (quoted straight from Jon's post on first page)
WHEN FLASHING HARDSPL, IT WON'T WORK THE FIRST TIME - YOU WILL GET AN ERROR (CODE 260). THIS IS EXPECTED.
Quote:
Originally Posted by joncgde2
This is what happens.
You go to flash HardSPL like the guide says. LOOK AT THE SCREEN ON YOUR PHONE, YOU MIGHT HAVE SECURITY PERMISSIONS AND NEED TO MANUALLY ALLOW THE PROGRAMS TO RUN.
It looks like it's about to flash and then errors. BUT your phone is on the 3-colour bootloader screen! How odd. Well KEEP YOUR PHONE ON THE BOOTLOADER SCREEN, and unplug it from your computer. Exit the HardSPL program, RUN IT AGAIN, and FLASH THE PHONE AGAIN WITH HARDSPL (obviously connect your phone and stuff back to your PC).
The point here is this: the first time it will fail, but at least manage to get the bootloader up. With this bootloader up, exit the flashing program, restart it, and then you should be able to run the flashing program and have it complete.
DOUBLE CHECK YOUR PHONE HAS THE OLIPRO HARDSPL INSTALLED after completion, by soft-resetting (hold the power and camera buttons at the same time AND use the stylus to press the putton at the bottom of the phone. You might not get it the first time, but with practice you'll get the hang of it).
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated.
Image Missing
Image Missing
10. Once your device is finished updating, it will automatically soft reset. Click the ‘Finish’ button to exit the RUU program.
Image Missing
To confirm is Hard-SPL is on your device, manually enter Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If successful you will see the tri-colour screen and the following will be displayed
Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
but also after restart a lot of time HARDSPLromupdateutility.exe, I still have the same problem!
anybody may help me?
Now I have stratos image,
maybe is this the problem?
Hi
Pls I need help, I tried to upgrade my HTC P3600 then my computer crash so now every time I try to start my phone all what I got is a picture (HTC start mobility) and then nothing.
Pls help me.
Thanks
Hi gys, I think that this is my first post, but I want to share some solution for with you. The most important think with "connection" errors is to have HSPL installed correctly. I was trying to install on my HD2 universal ones, like Hard spl v7 and 9, but problems occured. So after trying everything, I found HSPL (on this forum) just for HD2. After that, everything wass like a charm
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
base167 said:
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
Click to expand...
Click to collapse
You have choice a wrong HardSPL !!!
Olipro 3.10 and 3.20 are for HTC P3600i and no working for TRINITY P3600.
So, now probabily you don't see "USB" on Bootloader when you connect you trinity on PPC.
Solution:
You must reload your H-SPL With SD CArd.
It's very simple:
searching for a Hard SPL for trinity device, example Olipro 1.20 and rename file "RUU_signed.nbh" ---> "TRINIMG.nbh".
Then copy file "TRINIMG.nbh" in a SD CARD and insert it on your Trinity; After that , make a Soft reset with stylus reset +power+camera.
Power bottom for update your Bootloader.
Now you would see your trinity working again
Davide

Need assistance please

Hi,
I have a Rhodium and so far I have successfully flashed a lot of Roms untill today...
I am trying to flash another Rom via ActiveSync, so I have connected my phone to my PC, than run the CustomRuu.exe like always, but I am stuck at 0%.
I decided to flash using the SDCard and renamed the ruu_signed.nbh to RHODIMG.nbh and than I´ve enter in the BootLoader Mode, the device tries to load the Rom, but I´ve got a white screen saying "loading..." and stays like this forever.
I cannot even HardSPL the device. I run the Rhodium-HardSPL_V2_00R3.exe but i can not get the device properly synced.
I though I had an internal memory problem so I´ve formated it using a new tool found here: http://forum.xda-developers.com/show...12&postcount=1.
But now I´ve lost everything and I can not flash any Rom with activesync, always the same problem, stuck at 0% and then the message - "Error [276] : update error.", and if I flash from SDcard a white screen saying "loading..." and stays like this forever.
EDIT:
Can not HardSPL automatic flash, because could not get the device properly synced.
Can not HardSPL with Manual flash, stuck at 0% and then the message - "Error [276] : update error.#
Any help please.
Thanks
I have a Rhodium and so far I have successfully flashed a lot of Roms untill today...
Click to expand...
Click to collapse
Then I assume you already have hard-spl on your device installed. So trying to install it again will fail.
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it) and verify the screen shows 0.85.OliNex, which is the HardSPL version* Is this the hard-spl version that you have?
You didn't mention which rom you tryed to flash. Did you try other roms?
Lennyz1988 said:
Then I assume you already have hard-spl on your device installed. So trying to install it again will fail.
*Go into BootLoader Mode (do a Soft Reset while holding the "volume down" key on the left side of the device. Keep holding the "volume down" key until you see tricolour screen which is the bootloader mode, then release it) and verify the screen shows 0.85.OliNex, which is the HardSPL version* Is this the hard-spl version that you have?
You didn't mention which rom you tryed to flash. Did you try other roms?
Click to expand...
Click to collapse
Thanks for your reply,
Yes , you are right I have already HardSPL installed - SPL-0.85.0linex.
I have tried several Roms even the Rhodium stock Rom. If I flash via activesync I get stuck at 0% and if I flash from the SDCard (RHODIMG.nbh) I get a white screen saying "loading...." with no action.
This is strange as I´ve flash so many roms so far
Have you reset both your device and computer before connecting?
Just leave it in Bootloader mode and connect it to your computer and then try flashing.
As long as you put the device in bootloader mode, you do not have to get it to sync. I've done this many times when a flash didn't go right for some reason (like I forgot something when I cooked it ).
jaxboater said:
Have you reset both your device and computer before connecting?
Click to expand...
Click to collapse
rgb-rgb said:
Just leave it in Bootloader mode and connect it to your computer and then try flashing.
As long as you put the device in bootloader mode, you do not have to get it to sync. I've done this many times when a flash didn't go right for some reason (like I forgot something when I cooked it ).
Click to expand...
Click to collapse
I did both things with no luck.
I have put the device in bootloader mode connected to the computer then I´ve run the customRUU.exe but I am always stuck at 0%
This is the info I have in the tricolor screen:
RHOD100 32M SS-BC
SPL-0.85.0linex
MicroP(LED) 0x0A
MicroP(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
501,529 794,848
797,208 217,213
210,853 Calibrated
I will put the device in the AC power all night to see if this is a battery issue.
Thanks
have you used a different usb cable just a suggestion
jaredcg said:
have you used a different usb cable just a suggestion
Click to expand...
Click to collapse
I had the same thought and I have used a different cable but the results are the same.
just my 2 cents i have done it before try to uninstall the driver from computer when you are in tri-color mode in the device manager then unplug the usb and replug in the same usb port if doesnt work try other usb port
JEANRIVERA said:
just my 2 cents i have done it before try to uninstall the driver from computer when you are in tri-color mode in the device manager then unplug the usb and replug in the same usb port if doesnt work try other usb port
Click to expand...
Click to collapse
I would try this first as posted by jeanrivera.
Also maybe you're customruu is somehow broken? Try downloading a new one. Also I don't know if it helps but when you flash via customruu do you have the image named ruu_signed.nbh? I don't know if it matters what kind of name it has, but it's just a thought

[Q] Possibly bricked Trinity, help please!!!

Hello!
I have this problem:
I've installed WM6.5 on my Trinity, and it worked well, but today I wanted to try WM6.1 (0.4.9.0 digital) also. The following happened:
Everything worked fine, but at 54% flashing my brother lifted the phone, possibly it lost the USB-contact, because the flasing stopped with an error message (unfortunately can't remember the error number). Since then if I try to flash it with WM6.1 or WM6.5, after 1% the phone resets itself, and the RUU gives a 270 error.
I have the original WM5 ROM also, but if I try installing it, after "Verifying information on your PDA Phone" screen I get a connection error 260.
What can I do???
After the phone resets itself, I can see the HTC logo, and the red letters and numbers, but that's all.
If I try HardSPL, I also get a 260 error.
Can you enter bootloader manualy?
If you can than see SERIAL change to USB when connected to PC it should be OK.
if you have a SD card, you can also try to flash "manualy".
- put your RUU... NBH at the root of the card,
- rename it trinimg.nbh,
- reinsert the card in the phone,
- enter in bootloader (power+cam+reset)
you will have a grey screen asking to push "power", do it and that's it.
if USB is well working, maybe you just need to reflash the hardspooler.
Thank you for your replies.
Fortunately I solved the problem.
I did the following:
1. To be sure, do all the stuff on a Windows XP machine
2. DISABLE "Allow USB Connection" in Active Sync so you see a small red X symbol next to the Active Sync symbol
3. Start the device into Bootloader mode (Cam+Power+Reset) and connect the device to your PC and make sure USB is written on the bottom of your screen (NOT Serial!)
4. Download splxploit (http://forum.xda-developers.com/atta...0&d=1180043588) and execute unlock on your PC
5. Follow the instructions
6. Download HardSPL (http://forum.xda-developers.com/atta...8&d=1185364317) and follow the instructions
7. Finally (to be sure) restart into Bootloader mode and check if SPL is showing "SPL-1.30.Olipro) - if this is the case you've done it !
8. Flash your preferred ROM via miniSD or USB connection
I m glad you solved this. Every day another new way of solving the flash problems.
Hi to All guys
i've got a trinity from my work and it has a custom rom.
I wanted to changed the rom so i download a wm 6.5 and erase the trinity with mtty. After that i try to install the rom with he RUUUupdate, but it get error 270.
Only in that moment i read on the bootloader and see that it haven't olipro or another HARDSPL installed.
So i looked for a solution and i try the unbrick with the splxploit. I did it and i get olipro on the bootloader, but i don't know how go on with install, if i use the exe i get 260 connection error.
Can you help me?

My Head hurts....

I am trying to install 6.5 on my HTC touch HD.
i have looked at the guides, but i am getting nowhere......stuck at 0% on the flashing.
I want to flash Energys rom onto my phone.
Phone is currently
SPL 1.14.000
Radio 1.09.25.14
Rom 1.19.61.1 WWE
what do i need and how do i do it ?
i have downloaded
HSPLWrapper_Blackstone_156OliNex,
SSPL-Manual-TouchHD,
Unsigned_HardSPL_for_Blackstone_OliNex,
Energy.BLACKSTONE.29018.Sense2.5.Cookie.2.0.Apr.18
i have tried on both WinXP and Win 7 Systems, same error 262
1- have you tried installing the htc usb sync drivers manually? -->google
2- do you ever see the tri-color bootloader screen? If not you could try to put it in bootloader manually? you can do that by holding vol down+power button. You do have to turn it of first, and you have to remove the usb cable. WARNING: do not pull out the usb cable while its flashing, you won't be able to start your phone then (you can still flash roms though)
hope this helps
when connecting device to pc does bottom of bootloader (tri colour screen) change from "serial" to usb"? If not you need to either update drivers (see link in Dummies Guide) or open activesync and ensure that "allow usb connections" is enabled in connection settings
If above is all ok then you need to follow guide and get yourself HSPL
If getting stuck at 0% try trouble shooting section and use SSPL
Either way, please post further queries regarding flashing in Dummies Guide thread
Thread closed

Categories

Resources