HELP!! - 8125, K-JAM, P4300, MDA Vario Software Upgrading

I flashed radio rom 2.40 and it is screwing up my phone BIG TIME. i am using Faria's WM6 but this rom is killing it.
I cannot get to the bootloader screen even if I press the 2 buttons on the right and the Reset button but I cannot get to the loader screen.
Anyone know another way to get to the bootloader so that I can go back to the original 1.19 ROM.
Thanks,
Mike

ok, i read this in this forum because just 2 days back the same thing happened to my 8125... ok Charge ur phone with the battery still in it for 2 hours....then after thats done take out the battery and charge the phone without the battery.....Then pull the plug out and push back in for like 3 times (ur screen and orange led light should flash)...then without putting the battery back in hold the camera, power, and voice buttons at the same time until the bootloader screen comes up. Finally put the battery back in and unplug the charger, put the pc charger in and flash ur old rom....hope this helps, because it worked for me! Good Luck!
Arjun

ajdesidevil said:
ok, i read this in this forum because just 2 days back the same thing happened to my 8125... ok Charge ur phone with the battery still in it for 2 hours....then after thats done take out the battery and charge the phone without the battery.....Then pull the plug out and push back in for like 3 times (ur screen and orange led light should flash)...then without putting the battery back in hold the camera, power, and voice buttons at the same time until the bootloader screen comes up. Finally put the battery back in and unplug the charger, put the pc charger in and flash ur old rom....hope this helps, because it worked for me! Good Luck!
Arjun
Click to expand...
Click to collapse
damn it...didnt work. splash screen keeps appearing and disappearing and no bootloader screen.
Thanks,
Mike

HA....all is good.
I just followed these instructions from this thread and got bootloader to come on.
http://forum.xda-developers.com/showthread.php?t=294107
Basically, the only thing I did was remove my SD/MMC card and it went through no problem.
I flashed 2.19 Radio Rom back on my MDA so hopefully, everything is good.
Thanks for trying to help....
Regards,
Mike

Related

Xda IIi Dead???! Help Please!!!

Okay heres what happened. Last night whilst flashing my xda IIi to the 1.162 with O2 stripped out and camera fix rom, the winbloze bsod came up when it was part way through the CE part of the flash(the third part). The phone said it was complete but woudlnt boot up so I rebooted the pc and went through the whole flashing process again, which worked ok. I restored my backup and all was working well. This morning on the way to work I was using it with the wireless connection in operation and all was well. I switched it off and put it in the inside pocket of my jacket, to get off the bus to go to work and when I got into work I went to put it in the cradle and realised that it was very warm. Further more it would not switch when the power button was pressed. I took the battery out and tried my fully charged spare battery and whilst the boot up screen did come on quite clear initially, then it faded to blank white and now the screen is black and there is no response.
I tried a hard reset but still no response and the charging light does not come on when I put it in the cradle. If I take the battery out and put it in the cradle I get a flashing red light where the charging light is but otherwise, no other response. Is it dead? Is there nothing else that I can do? Please help someone as I am very attached to that device.
TIA
BTW the flashing red light when there is no battery in..... it flashes in a certain sequence of flashes. Does anyone know if these are error codes, pretty much like a pc will give a certain amount of beeps if there is a boot up error? amd does anyone know how to interpret them.
Once again, thanks in advance for your help.
are you try another bettery I think your bettery die
I have two original batteries, both do not work .
are you try to go to bootloader and flash it again I think 1.11.171 is the best rom
Update!!! Its life Jim but not as we know it!
Okay after leaving it on the cradle without a battery in for about an hour and a hard reset, it booted up to the windows mobile screen. After setting up the screen and such I was able to access the pda and restore a backup however
there is still a problem. It phased out a few times(screen faded to grey/white) and after setting up again it remained on but upon checking the power status I found that although the main battery was charging well the backup battery is on Zero and not charging. It has been so now for the last
3 1/2 hours sooooo that means that if the main battery loses power then I lose everything, also the bootloader has gone missing
I have this problem too with 2 of my xda II's its definatley not the battery as the battery works fine in my spare that i dare not update any fix for this yet?
helping you
hi im noel
can i know if any one help or did solve your problem in your xda 2i? i can help you just pm me...

Kaiser won't power up completely

I installed the Diamond Series L26 ROM and ran it fine for about 4 days. Then with no reason I can find windows started to respond badly and the screen didn't build up like it should.
I did a soft reset and after the phone came up. But after I entered my pincode the windows pretty quick gave a battery warning and went dead again. While I was pretty sure I had enough battery.
So at home I pluged it in (wall socket, original charger), the amber light went on. I booted it again and still no go. So I left it pluged in and waited a while it was 'charging'. But it still didn't react when I wanted to turn it on.
When I removed it from the charger and turned it on it booted again with the same result as the first time. I checked two text messages and the battery warning came again, and the phone turned itself off again.
After a couple of tries I tried a hard reset. No difference. Now my phone will boot until the message shows it is going to go back to factory settings, I hear a beep and it turns itself off.
I tried:
- Reinsert the battery (left it out overnight)
- Tried entirely different battery (fully charged)
- Plugged it in the original charger
- Plugged it in without the battery
- Took out SD card
- No SIM card inserted
- 'Powercharge' the battery with wires to the plus and minus contacts
- Rapidly pressing the battery against the contacts on the phone hoping to 'revive'something.
- Tried my battery in a different phone > it was fully charged.
Can it be the software thinking the battery is dead while it isn't?
...... help
Is a bump alowed the next day?
Anyway, is my problem that obscure...? Or is my post too long?
I don't want to know what T-mobile will ask for the repair without any waranty.
have you been playing around with Android?
Heb je met Android gespeeld?
Dust2Dust said:
have you been playing around with Android?
Heb je met Android gespeeld?
Click to expand...
Click to collapse
Nope. Just the L26 Kaiser Diamond ROM.
Sounds broken to me, try to send it back.
ChumleyEX said:
Sounds broken to me, try to send it back.
Click to expand...
Click to collapse
Yeah, but I know what happeneds next:
"We see you installed another ROM. Therefore voiding your warranty. That wil be EUR 300."
I am trying to avoid that scenario.
But perhaps I wasn't as techsavy as I thought. I read this in another post:
Steps before running the upgrade:
1. take out the battery to make the phone go off, unplug usb cord if you have it plugged to your pc.
2. put battery back in
3. Press and hold the camera button all the way in, then press the power button while still holding the camera button.
4. This will make your phone boot in to tri-color screen.
5. Now look at the bottom white area, when it says USB, connect your phone to your pc through usb cord.
6. Now you can just go ahead, open the rom you just downloaded and follow the steps.
Click to expand...
Click to collapse
That sounds like it is still an option for me as well. I was under the impression I wouldn't be able to reflash my phone because it wouldn't power up. I can try this, right?
hmm, maybe try that or flashing from the SD card. Either way go for broke, if you need to screw the phone up to the point that they can't tell what rom you have then go for it.

Is it bricked

I searched and searched. I was reflashing my AT&T tilt on a tmobile net, using the memory card method. I am not exactly sure what i did wrong. I flashed it once tonight and didnt like it even though it worked fine. I flashed it again and when I did the soft reset I think i took the memory card out to soon. Now the phone will not turn on at all. I love this phone, someone please help a brother out
Hard SPL
If I recall correctly, unless you were flashing the SPL, you just need to re-attempt the flash by engaging Hard SPL again.
It's been forever... but I seem to recall that with Hard SPL, you can always recover, unless you are in the middle of re-writing / overwriting SPL.
Erbid
(Tell us you do have Hard SPL installed.)
I cant get the thing to turn on at all I think I have tried every thing. I have flashed twice before without problem. But it just wont turn on now. I guess what im trying to say is I believe hard spl is on it. I ran boot loader from the phone using camera and soft reset. I accomplished the task once already and loaded the newest hyperdragon and didnt like it so about 10 minuts later i did the same thing and tried to install an old dutty one and the phone will not turn on. I loaded every thing and then reset. I think i may have pulled the memory card to early because i dont remember the phone saying it was clearing storage or coming back on. Sorry if this seems longwinded.
Sorry if this is a stupid question but is the battery fully charged? Try charging for a few hours - check that the charge light is on etc. Normally with a bad flash, even if the phone is completely bricked, you will see something try to light up or go brighter on the screen - unless the battery is dead or the screen ribbon disconnected.
It worries me a bit that you 'think' you have hardspl. Either you do or you don't. The process is simple enough to do but has enough steps that you'd definately remember doing it.
Ok, so I think you are sorta right. I put a fully charged bat into the phone but still nothing coming on. Turns out the old battery was dead though. Strange considering it was being charged all day while in the car. phone still wont turn on. anyone know if there is someone who fixes these?
[email protected] said:
Ok, so I think you are sorta right. I put a fully charged bat into the phone but still nothing coming on. Turns out the old battery was dead though. Strange considering it was being charged all day while in the car. phone still wont turn on. anyone know if there is someone who fixes these?
Click to expand...
Click to collapse
okay the phone isn't turning on but are there any led's lit up? (red, green, orange??) because that indicates there is still life in the phone and recovery is possible. This can be when you turn it on or on charge etc.
Very unlikely you bricked it. More likely a problem with the battery or charger not charging the battery.
When you plug the charger into the phone does a yellow light appear at the top to indicate the unit is charging? If not you have a faulty charger.
Can you get into the BootLoader screen? Try the following:
> Take you battery, sim card (re-lock the cover after taking it out) and storage card out
> make sure all contacts on the battery are clean and replace it
> Hold the camera button in fully and then press the power button for a few seconds (the Bootloader screen should appear)
If the Bootloader screen comes up then read the 2nd line down which starts SPL and report back with the version.
If no Bootloader screen appears then take the Battery out and plug the charging cable into the phone. Then with the battery still taken out, try to get back into the Bootloader screen by holding the camera button in while pressing the power button.
If that gets you into the Bootloader then then problem is with your battery.
If the phone still does not go into the Bootloader screen the problem is most likely with your charger.
thanx, i have since bought another tilt. I put the old battery in the new tilt and it was dead. I put the fresh battery in the old tilt and nothing yet. I didn't try the bootloader yet. I did try charging the phone on the old battery though and no lights what so ever. even with new battery on charger. I will get back to you on the bootloader trick
Bootloader trick didnt work. Thank you though. Looks as if I now have a parts phone that My wife hates me for.
[email protected] said:
Bootloader trick didnt work. Thank you though. Looks as if I now have a parts phone that My wife hates me for.
Click to expand...
Click to collapse
Have you tried the charger from your new tilt in the phone that doesnt work? If you connect the charger then the charging light should come on at the top. If thats not happening but it works on your new tilt then the problem lies in the phone. You can try checking contacts and connections but if you have no life after swapping bits over from your new tilt to the old one then ur pretty much buggered. Can you not send it back as faulty or is it out of warranty?
No warranty. I bought it used. Im on Tmobile. Thank you for everything though. I did try the new charger and got nothing.

[HELP] Flashing gone wrong???

It looks like that i bricked it.
Here is what I have done.
I used Hard SPL Utility and got it to say 0.72.Olinex
After that I used TouchIT 4.5 to flash it. it went through but after going through calibration it now keeps rebooting. Sony Ericson screen comes on. disapears and reboots.
Please anyone help
hard reset didnt work either
flash it with other rom and see. boot to tri color screen and start your flashing, computer can recognise it
tried that I am getting update error 262
ok its official the phone is dead. it gave me 270 error then rebooted. and done. doesnt even want to power on.
mprielozny said:
It looks like that i bricked it.
Here is what I have done.
I used Hard SPL Utility and got it to say 0.72.Olinex
After that I used TouchIT 4.5 to flash it. it went through but after going through calibration it now keeps rebooting. Sony Ericson screen comes on. disapears and reboots.
Please anyone help
Click to expand...
Click to collapse
I just want to tell you that flash hard-spl is something different then flash a rom...
Each one has his own software for flash...
So first is to hard-spl your xperia...
And then i recommend you to flash the rom phone via the microSD
Just rename the touch-it 4.5 to KOVSIM.nbh and put it to the root of the MicroSD..Then restart your phone with Volume down and power button together...And then follow on screen instructions
Note maybe you should try to read this thread, study a little and then flash.....
http://forum.xda-developers.com/showthread.php?t=477801
Good luck....
well I have used the one inlucded in X1_HardSPL_Utility.zip from one of threats here.
then I used the Touch-IT_v4.5.rar
i even tried X1_RUU_ROM_UpdateUtility
dont know what I did wrong.
now it doesnt even power on.
mprielozny said:
well I have used the one inlucded in X1_HardSPL_Utility.zip from one of threats here.
then I used the Touch-IT_v4.5.rar
i even tried X1_RUU_ROM_UpdateUtility
dont know what I did wrong.
now it doesnt even power on.
Click to expand...
Click to collapse
Satrange i have like 10 times and no problem...
Just pull the battery out try it on again...
Maybe you should download and official rom...or original are the same
The ones ins PavelX1 thread...
And Flash with ones of them via MicroSd...
MicroSd method is much safe than rom update utility...Remember to have at least 50% battery....This is very important..
Dont worry you phone is not broken...
try flashing using SD card, search the forum for the method
edit : too late for the reply, hope you get it working.
Try booting to tri-color boot screen (decrease volume button + power on button)
thing is it doesnt power on now
removed battery, put it on power only nothing.
--sorry double post---
mprielozny said:
thing is it doesnt power on now
removed battery, put it on power only nothing.
Click to expand...
Click to collapse
It won't boot without the battery no matter what you try.
Leave the phone on charge overnight then try flashing a new rom using the SD method.
Did you make sure you had a decent battery level (>50%) before you started flashing your rom??
it had 100% it flashed and I even calibrated the screen on reboot. but after that it started rebooting continuosly. I dont know if it juiced it out. well I will leave it on charge for some time to see if that helps.
mprielozny said:
--sorry double post---
Click to expand...
Click to collapse
Maybe try to recharged it?????
Mybe battery is empty
It may sound like a joke but charged the phone...?
Does it make something when you connected to the wall charger?
If so wait until it recharges about 4 hours and then try it again...
If it flashes then your xperia is not broken....
Some others users have this same issue with that rom...
So maybe try and official rom trust me flash it via microSD method always
Rename the official rom to KOVSIMG.nbh and the copy to the root of the microSD memory
shoudl something blink or is there is indicator if it is charging when plugged in the wall charger?
mprielozny said:
shoudl something blink or is there is indicator if it is charging when plugged in the wall charger?
Click to expand...
Click to collapse
yes, the LED above the USB connector on your mobile should be blinking.
if the battery went flat completely, it will take some time to start blinking.
mprielozny said:
shoudl something blink or is there is indicator if it is charging when plugged in the wall charger?
Click to expand...
Click to collapse
It shouldt blink on sides or it shouldt turn red the power button ...
But sometimes you have to wait some minutes
mprielozny said:
shoudl something blink or is there is indicator if it is charging when plugged in the wall charger?
Click to expand...
Click to collapse
Not sure... might dep the rom.
Normally my led's flash/glow... but I haven't had a look at it charging whilst the phone is off.
Charge it for half an hour or so and then try to get the boot loader up (hold power and volume down to turn on).
If the boot loader (striped screen) starts you should be able to fix a bad flash.
Turn the phone off and charge it overnight
get a rom you know (the .nbh or .image file) and rename it "Kovsimg.nbh"
put the Kovsimg.nbh file on the root directory of your storage card (you might want to take the card out of your phone and put it in a card reader to do this)
boot your phone in boot loader mode (hold power and volume down)
follow the prompts to install the good rom.
After its complete, reset your phone (either by putting your stylus in the reboot hole or taking the battery out)
All should be good
well 30 mins and no flashing lights, power button doesnt work. connecting to PC doesnt work. I am out of ideas.

N1 not booting up...LED flashing orange-green-green

Hi,
i need some help trying to figure out what do i need to do to get my N1 to function again.
I had KiNgxKxNexus Desire2Nexus (v1) ROM loaded on my N1. i don't know for what reason i tried to load latest intersectRaven's Kernel(20100421_2237-the update.zip version)on top and that's when i start having issues. After i loaded the .zip file, phone rebooted and it was stuck/looping on the HTC screen for about 10 min.
I removed the battery and since then i cant get it to boot. all i get is a flashing LED (top right side)--looping on orange-green-green.
removed battery, SIM, SD card.
I plugin the wall charger(with no battery) and same issue.
when i put battery back in, i get the LED red, and if i try to power it on, i get same loop - orange-green-green.
tried to connect N1 to PC, and use adb, but PC its not seeing the phone.
Any help is appreciated.
Thanks.
Just go into recovery and wipe then flash your desired ROM.
You get a similar sequence, when you try to start the phone without the battery pack (with just the charger). I tried that to help someone in another thread, so just remember the phone won't start without its battery.
I don't remember the exact orange/green sequence in my case (and don't have the charger with me right now), but i guess that either your battery pack died coincidentally or that there is some other low-level hardware problem. The red light could also indicate an empty battery (that maybe broken and won't charge).
Can you borrow a battery from someone? I wouldn't try to use your battery in another phone to be safe though.
SiNJiN76 said:
Just go into recovery and wipe then flash your desired ROM.
Click to expand...
Click to collapse
How? Phone's dead (at least for now)
SiNJiN76 said:
Just go into recovery and wipe then flash your desired ROM.
Click to expand...
Click to collapse
i cant go into bootloader or recovery. tried the power+trackball, power+vol down... no luck. - my PC doesn't see the phone to use adb.
when i turn the phone on, my screen its black...i don't get anything on the screen.
i got it to work.
over nite i left the battery out of the phone. this morning i put the battery in, plug in the wall charger, and turn the phone on (power+trackball) and i got to bootloader. from there i was able to go in recovery and fix my phone.
hey, thats great! please have a look at the battery from time to time, if the phone gets hotter than normal.
I have the same problem, but not because i flashed , but I put strange extra battery in , that didn't worked, And N1 was just flashing orange, green , orange, green, 1 sec interval ...
I put new one in and worked like a charm.
Don't buy from 4U-kidi. Dead battery!

Categories

Resources