Database Develop

WM05 AKU2 to BA - test

I need someone to test this ROM, because I dont have a BA.
OS 5.1.195 (Build 14847.2.0.0)
STOP !!! ROM IS NOT WORKING
"ftp://xda:[email protected]/Uploads/BLueAngel/WM5_BA_-_AKU2 TEST.rar"
It is possible that you have to reflash the old rom!

Is this based on the Himalaya rom?

How likely is it to turn my BA into a paperweight? LOL
I am donloading it now mate.. Will post any results in about 2 hours
Gruß aus Malta!
Juggs

I used the the newest QTEK Wizard Rom.
There would not be any difference between Him or Wiz OS. Same build same files.

bepe said:
I used the the newest QTEK Wizard Rom.
There would not be any difference between Him or Wiz OS. Same build same files.
Click to expand...
Click to collapse
?? no omap or xscale code optimalisation ?? files can not be the same :|

I ported the German Wizard rom successfully to my Himalaya and I did the same with the WWE version at this rom.
But there could be differences. In this case, the rom would not work.

First Impressions..
OK.. bearing in mind that i only installed the Ivan Rom about 3 hours ago.. My MDAIII is getting a beating tonight.. However...
Ok.. Standard stuff.. Bootloader mode.. Set operater..
The update was relatively quick.. only took about 8 minutes,
Formatted the hive and storage OK..
And it hang on the Windows Mobile Screen!
and it keeps on hanging on the windows Mobile Screen.. :?
No New device Setup.. No shimmer of life.. No backlight.. Just the on/Off button Works
Sorry mate.. Back to the drawing Board!

I have not changed the drivers, only the OS.
I compared a Univesal and Wizard rom and the OS is exactly the same.

That may well be bepe.. But it doesnt install past teh windows Mobie screen...
Something is wrong mate.. normally it should give you that screen you get when the device need to be setup the fist time.. and it doesnt.. It just hangs..
Sorry..

Ok thanks and I'm sorry.

Ahh well! Thanks for your attempt Bepe. It seems he got to the same stage as Mamaich & Tuatara.

bepe said:
I need someone to test this ROM, because I dont have a BA.
OS 5.1.195 (Build 14847.2.0.0)
"ftp://xda:[email protected]/Uploads/BLueAngel/WM5_BA_-_AKU2 TEST.rar"
It is possible that you have to reflash the old rom!
Click to expand...
Click to collapse
***NOTE: To all wanting to test this, the ROM will not finish the BOOT sequence. This is the same or similar problem both mamaich and I have had with undertaking the Himalaya AKU2 Port to date. ***
The device will initialize, gets to the 'boot splash' screen, runs that ...
The "coldinit.exe" is started, since we hear the 'ding' happen ...
At this point the device locks - an animated "dialog" appears to want to be displayed.
The boot process proceeds no further. Presumably crashed.
Additionally, the LEDs are dead/disabled so I can not tell if the phone (RIL, BT, etc.) is still available/operating. Power button or screen taps do NOT relight the backlight, or enable the screen. Presumably locked up.
Ok ... excellent work so far, however the same problem(s) seems to be arising which both mamaich and I have run into when using the Himalaya AKU2 port.
My guess is that this is probably due to the same missing DLL interface calls being available in coredll.dll. There are now 5 additional entry points in the XIP portion of this DLL, and this could be causing the 'hang'.
It looks VERY promising though ... I'm definitaly going to be taking a VERY close look at this ROM as well. The boot sequence is quite dramatically different, and may lead to some possibilities in merging ROMs to avoid the requirements of changing XIP section modules.
P.S> TuMa v1.4 will be out shortly ... it's now combining elements from the Wizard, Himalaya 1.7x & 2.0, Jasjar, Atom, Acer, and the original v3.1 BA from mamaich now. Trying to merge the 'best' of the available elements for a well performing and stable device.

Not a problem.. Just let me know when you want another one tested!
Gruß Aus Malta..

OT: has anyone tried porting Universal rom? is it possible?

@Saintraziel:
Would be the same result.
And a lot more work to do because of the VGA resources.

aku2
Would this give AKU2 functionality for blueangel? (PH20B)
If so I would be happy to test any builds, I am dying to get my hands on a working WM5 with push email on BA.
Cheers...

[Download Link Added] Syed Ather WM6 AKU 1.0.0 (real) RAMDISK 80MB

Syed Ather's Windows Mobile 6 for Hima​
1. Information:
ROM date: 11/11/2007
Program: 61.25MB
Storage: 30.53MB (after running HimaDOC tool)
RAMDisk: 79.64​
2. Supported device:
O2 XDA II, T-Mobile MDA II, Qtek 2020, iMate Phone Edition, TSM500, and other PH10 device
3. Illustrative pictures :
3. Main Functions:
WM6 CE OS 5.2.2000 (Build 20000.1.0.0 ather90)
Comm Manager 6 buttons.
Windows Media Player for PPC Version 11.2 (Build 20000)
Device Lock Today Plugin
HTC Action Screen
BT Explorer v 1.2
Office 2007
Default Keyboard Selector
Keyboard skin (Black and White)
Download : http://rapidshare.com/files/69004141/SA_WM6_AKU_1.0.0.rar

Looking forward to it ...
But... what about the pagepool? The Ramdisk is way too big to have enough performance in my opinion.
Gonna test this right away

No the rom speed is good...i am uploading right now

(real)AKU1.0.0??
@ather90
what It can reflect the AKU1.0.0(real)?
How can get the 80M Ramdisk？The Program: 61.25MB??128-80=48M(60.25)??
and the pagepool is it loss??

the term "real" was meant for RAmdisk....the RAMdisk isnt affecting any feature of the ROM..first u guyz were complaining about low ramdisk and now Biger RAMdisk
Just test it out and u i'll know the difference

I will test it soon as I have time for it. Thank for your work

after a soft reset the ram disk loses all data.
not good, sorry.

This one is still based on the very old WM6 Wizard ROM.
It has lots of ghost-files in it.... (like touch.dll; *.dsm; ... )
Curious if this one is more stable then the others !
Thx for your effort... appreciate it (really)

Thank u guyz ..really appreciated it

Files in ramdisk lost after softreset
Hi ather90,
I've installed your ROM, its fast..
one problem though i find programs installed in ramdisk dissappeared after soft reset ...
Any chance for a quick fix ?
-Erman

What is your pagepool size and how did you manage to squeeze-in so much RAM Disk.

would it be possible that you release a 32mb ramdisc version?

Carkit not functional with this rom
Syed,
is the carkit functionality builtin this time? This because after flashing your newest rom there is no sound from the carkit speaker. I used wavedev2.dll and edited the register with taskmanager for wm6. This gives no result. Can you help me?
Greetz Frotter

i will see what i can do
@wertzui
I will release A.S.A.P

thanks, but could you also do something about the problem, that the ramdisc gets erased everytime, a soft-reset is done?

Little question:
What are the differences between AKU 0.7 and 1.0.0?
Thx.

does it have the problem of lost sms?
mine is a T-mobile MDA. I had 696 wm6(chn) rom and got lost sms. Is this new one ok with this issue? thx.

Hi, ather90! First, let me congratulate: nice good job!!! But, one question: this ROM is the only one i see with OS version number 5.2.2000. is that real or a 'personalization'? i'm searching for a kitchen to make my own cooked ROM, but i found only TofClock one... in case, have you planned a your kitchen for n00bs like me?

Hi mates...can i upgrade my WM2003 SE to WM5 or 6 in a Qtek 2020i???
Thanks

Macedo said:
Hi mates...can i upgrade my WM2003 SE to WM5 or 6 in a Qtek 2020i???
Thanks
Click to expand...
Click to collapse
There is no version of WM5 or 6 available for 2020i and there probably never will be.
BTW I do advice you, next time you visit a forum, first browse it so that you know that you're in the right section. 2020i is known here as Alpine and has its own section here http://forum.xda-developers.com/forumdisplay.php?f=249 to clearly seperate it from Himalaya. In that section your question has been asked and answered over and over again

HTC MTeoR WM 6.1 A4 ENG (Beta 1 - B1)

Hello all
Wm6.1 alpha 1 Ver.5.2.1711 (Build 19202.1.0.0)
Many bugs (high instability)
WM6.1 alpha 2 Ver.5.2.1711 (Build 19202.1.0.0)
Many Bugfixes (Usable)
Accesibility-working
Comm manager-working
T9-working
Power-NOT WORKING (you have to regedit)
WM6.1 alpha 3 Ver.5.2.1711 (Build 19202.1.0.0)
Many Bugfixes (Very Usable)
Accesibility-working
Comm manager-working (without bluetooth) - fix in progress (A4)
Bluetooth working - separate menu
ad2p fixed - proper version
T9-working
Power-working
Suspend -working
XIP - Rebuilded
Caller ID -working
HSPDA-working
GPRS-working
GPS-working (external device)
MMS - working
2 beam in control pannel !!!! - fix in progress (A4)
Please test and tell me if is anything wrong and if you find fixes
WM6.1 Beta 1 Ver.5.2.1711 (Build 19202.1.0.0)
Many Bugfixes
Accesibility-working
Comm manager-working (COLOR with BLUETOOTH)
Bluetooth working - separate menu
ad2p fixed - proper version
About - FIXED
T9 - working
Power - FIXED
Suspend - working
XIP - Rebuilded
Caller ID - working
HSPDA - working
GPRS - working
GPS - working (external device)
MMS - working
2 beam - FIXED
Windows Live - FIXED
you must update Windows Live to latest version
http://rapidshare.com/files/106073863/Windows_Live_10.6.34.2500.cab.html
ROM Links
http://rapidshare.com/files/105874292/MTeoR_-_WM6.1_-_A3.rar.html
http://rapidshare.com/files/106079473/MTeoR_-_WM6.1_-_B1_-_ok.rar.html
Please test and tell me if is anything wrong and if you find fixes
Also released the A4 kitchen
Many thanks to
Bepe - Tools
Mamaich - Tools
Dr Martin Gonzo - support
Garmin - support
futureshock - Test and bugreport

Hi, from where comes the Wm6.1 Roms?!
when you give it me i will try to made other languages too of it

jerpelea said:
Hello all
This is the alpha version of wm6.1
Please test and tell me if is anything wrong and if you find fixes
http://rapidshare.de/files/39013516/MTeoR_-_Splash_Screen.rar.html
http://rapidshare.com/files/98157272/WM6.1_Segoe.cab
http://rapidshare.com/files/104652554/MTeoR_-_WM6.1_-_A1_-_ok.rar.html
tomorow i will release the rom kitchen
and vanilla wm6 & wm6.1 roms
Many thanks to
Bepe
Mamaich
Dr Martin Gonzo
Garmin
for their tools and suport
Click to expand...
Click to collapse
how cook chines ROM?

good job! thanks very much!

Wow Cooooool man good job thanks

hello,jerpelea !
I find this rom in "seting", "Power Management","Accessibility" is bad."regional settings" locale is russian,and lose "systerminfo"
my english is poor,wish you can understand.

Hello lyf1998
fixed accesibility
working on power settings
i know that locale is in rus (is normal)
Where did you find sistem information ?(it is not included in this rom)
I will not cook chinese rom
please learn english, read forum and learn gow to cook or add locales.
I will release the Kitchen so that you could cook yorself an rom
Thanks

jerpelea said:
I will release the Kitchen so that you could cook yorself an rom......
Click to expand...
Click to collapse
Thanks.
呵呵，谢谢。

released
till monday i will release an A3 version

jerpelea is KING!
Hey jerpelea. Thanks so much for getting this out, I loaded it up as soon as I got home Friday night. Observations so far:-
Pros:-
-Very fast loading, much faster than latest WM6.0 out for Mteor
-Very fast running, including loading apps.
-Visually, complete makeover. Much happier with this Today screen than any plugin I've seen.
-All software attempted to far works fine- Route66, Google Maps, Skype (as well as it does on the mteor anyway!).
Issues:-
-msn messenger not installed, however Today screen expects that it is there. When selecting to sign in from Today screen, it comes up with a connectivity issue immediately, however no connectivity issue exists. I can install WLM seperately, but would be ideal to have the sign in from the Today screen as intended. Also when I've installed the latest WLM, there is a strange issue where I cannot do backspace- the 'back' key does not delete text and move the cursor backwards. Makes MSN virtually unuseable for me.
-Phone intermittently does not resume from standby- is frozen. It is still flashing to say that it's on and connected, however no buttons will revive it- the only way to revive is to remove battery and reboot. When phone restarts new messages and emails come in- leads me to believe phone was frozen.
-Phone intermittently wakes up for no reason- have had the phone sitting next to me for a night, and it lights up brightly at random intervals.
I am blown away with this release- it's made my Dopod 595 my favourite phone to carry again, over my Hermes and Asus Halley. A few issues to be resolved obviously, but it's exciting that we're getting such recent builds of WM6 for our Mteor's.
Keep up the great work, holding my breath for the A3 release!!!

does it work with dopod 595 variants with forward facing camera? and also, can you please point us to SuperCID unlock guide? thanks

Dopod 595 & WM6.1 A2
alexnvidia said:
does it work with dopod 595 variants with forward facing camera? and also, can you please point us to SuperCID unlock guide? thanks
Click to expand...
Click to collapse
It sure does work with the 595, albeit with the issues mentioned in my previous post. I'm honestly not sure about the front-facing camera, hadn't tried it yet. Will try tonight and advise.
In terms of getting around the CID issues, there will be 3 registry edits you will need to make (need to copy regedit to phone and run to make changes), and also a piece of software to application unlock. This will make your phone Application Unlocked.
You then put Des' SSPL on the phone, run it and immediately press the power and camera buttons. It will then start with the special SSPL, which gets you around the CID locking. You can in theory update via the update software (RUU) after this, however I have always upgraded via putting the rom onto the memory card as "BREEIMG.NBH". There is packaging software that will allow you to put your own choice of radio, rom, splash-screen's etc together.
In terms of the SSPL process, this is very well documented on the forum. Just take a look. I would not attempt the SuperCID process suggested- which involves loading the Hermes unlock tool to the phone. The hardware may be the same, however the command to enter the bootloader is not, I have bricked my Dopod 595 TWICE doing this- both times having the board replaced (under warranty luckily!). Up to you to attempt if you like- however I just don't see that it's really worth it until there is a dedicated and foolproof process.
Remember that these rom upgrades don't include the radio upgrade- so if you are upgrading your firmware for the first time, best to flash the most recent HTC WM5 upgrade first (incl. radio 1.38.x). Or an extracted Hermes radio rom. Just ensure it includes HSPDA.
If it's your first upgrade, and you don't like the idea of upgrading many times, I'd perhaps wait until a more final WM6.1 for Mteor is released (perhaps A3 or a RC).
I'm far from an expert, but have played with these, and my Hermes a lot. If I can perhaps answer anything else, please let me know...

MMS
jerpelea can u add MMS program to your A3 release???

stuartmclean said:
It sure does work with the 595, albeit with the issues mentioned in my previous post. I'm honestly not sure about the front-facing camera, hadn't tried it yet. Will try tonight and advise.
In terms of getting around the CID issues, there will be 3 registry edits you will need to make (need to copy regedit to phone and run to make changes), and also a piece of software to application unlock. This will make your phone Application Unlocked.
You then put Des' SSPL on the phone, run it and immediately press the power and camera buttons. It will then start with the special SSPL, which gets you around the CID locking. You can in theory update via the update software (RUU) after this, however I have always upgraded via putting the rom onto the memory card as "BREEIMG.NBH". There is packaging software that will allow you to put your own choice of radio, rom, splash-screen's etc together.
In terms of the SSPL process, this is very well documented on the forum. Just take a look. I would not attempt the SuperCID process suggested- which involves loading the Hermes unlock tool to the phone. The hardware may be the same, however the command to enter the bootloader is not, I have bricked my Dopod 595 TWICE doing this- both times having the board replaced (under warranty luckily!). Up to you to attempt if you like- however I just don't see that it's really worth it until there is a dedicated and foolproof process.
Remember that these rom upgrades don't include the radio upgrade- so if you are upgrading your firmware for the first time, best to flash the most recent HTC WM5 upgrade first (incl. radio 1.38.x). Or an extracted Hermes radio rom. Just ensure it includes HSPDA.
If it's your first upgrade, and you don't like the idea of upgrading many times, I'd perhaps wait until a more final WM6.1 for Mteor is released (perhaps A3 or a RC).
I'm far from an expert, but have played with these, and my Hermes a lot. If I can perhaps answer anything else, please let me know...
Click to expand...
Click to collapse
you sound pretty much like a guru here.. it will be very helpful if you can provide the links to the documentation of the CID, SSPL, ROM, or anything relevant here. i know i can do a search, but my 595 is out of warranty and it wouldnt want to risk killing the phone with the wrong process or procedure.. unlike the startrek thread, the superCID and unlocking process are well pointed(links) and explained in the ROM update packages. i find that Breeze's threads are a bit fragmented here..
so if it's not too much of trouble, maybe you can start a new thread explaining the unlocking, CID, SSPL, and Radio upgrades in detail. im sure the admin will make this useful thread sticky for nobs (like me). cheers.

have you looked into wiki?! there are many infos...
CID Unlocking isnt researched sofar that you can use it without starting the sspl from a running device... so that means theres no HARD SSPL yet...
and i think there would never be..
i have tested to flash devs sspl but it didn't worked...
i'm also on the side that the mteor is a smartphone thats not really widly in use... so theres no big community behind they develope!
DEv has done so much with his sspl...
and with wm6 and wm6.1 yet i think thats much more i have ever imaginaryed!

thank you again! but i still do not run rom Kitchen.

is it possible to put in the neo-plugin today app from the mteor wm6.0 roms?

lyf1998 said:
thank you again! but i still do not run rom Kitchen.
Click to expand...
Click to collapse
cant help
i have
.net 2.0
.net 3.5
visual c redistributable
windows XP sp2
Does not work on vista
BR

Hmm....
was what I got trying to upgrade...

techdev said:
is it possible to put in the neo-plugin today app from the mteor wm6.0 roms?
Click to expand...
Click to collapse
Yes but NO i will not include it
You have the kitchen you can include it if you like
This is a vanilla version
I will try to clean it of bugs
Everybody who wants an localisation or an software will have to add it
BR

Dumping standard shipped ROM

Is there anyone who has succesfully dumped the Official Shipped ROM that comes with the European models ?
I'm sure that apart from me, there are other members who would like to revert to the offical ROM just in case something happens with the device. (need to send it back for a reparation)
I'm going to flash just right now anyway, as I'm positive that there will be someone in the future dumping the offical ROM.
\cheers, now pressing start
EDIT : After flashing I keep the high pitched noise that almost everyone is Reporting. I can't get rid of it. Be aware with this ROM,. you might get stuck with a hissing device that won't stop I'll wait for some solution and then flash again, can't use Winmo anymore

me too...please help us - i cannot use my device due to constant noising...

up0grading the EC chip drivers
I saw some remarks about the EC Chip driver update from HTC - will try that now, see if it helps anything at all.. For now, the device always hisses like a snake when Vista is active.
Without Vista active, it's mostly quiet, but gives no sound in WinMo, however, if you try to make a sound in WinMo, sometimes, after a few seconds, it will hiss and pitch for the duration of the sample played...
This is really annoying

hi,
i did a backup pof's way, so i have now part00.raw - part04.raw and SPL.nbh.
Rebuild Part02.raw and uploaded again. Working like a charm. Problem is: my original ROM is in German. anyone interested?

german but quiet is much better than english with noise.
please provide links.
Thanks

GERMAN..?
That sounds wonderful: need the the german ROM very urgent, can`t work with my beloved shifty...
Please share the ROM, thanks so much!

Me too!
I installed the GPS Bios pack - Easy BUT:
The noise only appears while staring after reinstalling the battery - just restart SnapVue after Vista is up and the noise is gone.
Also gone is the German keyboard under SnapVue - Regional settings don't change that!
GPS work in SnapVue and Vista (using ActiveSync & GPSgate - after test period ~30€).
Overnight SnapVue need app. double the energy than before!!!
Using GPS in Vista means NO internet/mail!
Wrong keyboard layout and battery drain tempt me to reinstall an original German ROM and to continue using my dear old eTrex with USB together with my Vista progs.
So, how and where2 can I find the German ROM?
Thanks,
Axel

Send the Rom-Link to a victim already. Waiting for an OK before i publish.

Victim report Nr. 1:
@tece: Thanks a lot, man, good job, it works fine..!
Regards and thanks a lot.
Alex

great!!
i noticed that pocketie is already installed and that \Windows\StartUp\PKG.exe and BlockTitleBar.exe are already removed.(like i did as described in this: http://forum.xda-developers.com/showthread.php?t=377441 thread before backing up the original ROM). Now I'm looking to get the registry preconfigured to not start Snapvue. Liberated German ROM will get released this weekend. If you can't stand waiting for that ROM send me or traumrakel a PM for the rapidshare link.

If you could include the liberation into the new ROM I would prise your name... ;-)

and here it is: http://forum.xda-developers.com/showthread.php?t=417901

I have rom dumps of:
- 1.30 WWE
- and whatever rom the CDMA shifts have.
does anyone need either?

cmonex said:
I have rom dumps of:
- 1.30 WWE
- and whatever rom the CDMA shifts have.
does anyone need either?
Click to expand...
Click to collapse
hello cmonex,
i m running the german rom as i do not have my original french dump, i would be very happy to install 1.30 WWE!!
even if tece rom is great in order to learn some german word

cmonex said:
I have rom dumps of:
- 1.30 WWE
- and whatever rom the CDMA shifts have.
does anyone need either?
Click to expand...
Click to collapse
Do you have the reconstructed ROM of version (original UK Shift): 1.30.405.0 WWE ? Can u post it/send it? Then I don't have to rebuild it myself, because I'm not that experienced it rebuilding myself. Also in case my rebuilded rom fails to work.
Many thanks!

cmonex
Could you please share the 1.30WWE
Thanks
Ram

You have it, it's the one having gps and sound bugs with european radios.
I'm using 1.22 because it's a stable base. Later version doesn't give you much, as graphic drivers are disabled anyway.

thaihugo
Cool. I followed pof's suggested way of dumping the original rom. Now I got all the raw files with correct start addresses. I am wondering whether I did correctly or not for SPL.NB. because the file size is 256 KB since I passed the same length 262114 as read in pof's post. When I used KaiserKitchen to reconstruct, I don't have baseRom and if I ignore that, I am not gettting the NBF file. I want to backup my CHT ROM and install your's (1.22 with GPS and sound). Could you please shed some light?
Thanks
Ram

Hi Cmonex ;
I need the non-touched 1.30 WWE rom for shift ; can you share please ?
Safak

Thaihugo , Saiweb
Do you have 130 WWE non-touched original rom ? I ve downloaded one from the forum but it is the "telenav"ed orig one , which i can not use at all...
Can you share if you have ?

Swedish unlocked htc 3600 pro upgrade confusion, help appreciated

Hi, I´m new in this forum and would like to start off with a big thanks to all the developers and home-cookers on this forum for their great job doing what they do
I recently bought a new unlocked HTC p3600 (pro) which apperently came from
the swedish provider 3. This package also included TomTom 6 but is yet not installed on the trinity.
Of course i would like to update my trinity to wm6 or a stable wm6.1 and after reading in alot of forums and different guides I think I´ve got a good handle on how it will go down, so I´m pretty confident how to update my machine
First of all I´d like to post the speccs of the htc 3600:
I bootloader mode it says:
(Red stripe) TRIN 100
IPL -0.50
SPL -1.07.0000
(Green
and blue Clear
strip)
(White stripe) SERIAL (becomes USB when connected to PC)
----------------------------------------------------------------
In deviceinfo the speccs are as follows:
ROM version: 1.23.413.2
ROM date : 03/13/07
Radioversion: 1.16.00.00
Protokoll version: 32.53.7018.01H
ExtRom version: 1.23.413.9700
------------------------------------------
The Rom version appears to be same htc-europe has on their site
since the file there says: driver date 2008-09-17
Windows Mobile 5_ROM Upgrade_Swedish (1.23.413.2)
And the tomtom6 (driver date 2008-09-09) is also available for download there so no need to upgrade that I think?
As far as I understand from this forum, trinityguides.info, Ruslan Trifonov's blog, http://forum.lowyat.net/topic/717790 and of course the upgrade guide for vista users here:
http://www.4winmobile.com/forums/htc-trinity/12987-solved-problem-upgrading-trinity-vista.html
I need to flash the original spl to a hard spl either using
olipros 1.20, 1.30 or des´s crash proof spl
with RUU and so on. Same goes for the Radio and the wm6 ROM I would like to use
My questions now are these.
1. what hard spl will be most suited for this proceedure? (since the phone is unlocked, i can put alot of different sim-cards in it like Tele2, Telia, 3 and so on) BUT.. I´m not sure if the phone still has CID lock and I´m too stupid to properly use mtty.exe
2. What Radio version is most compatible with the hard spl and the wm6 or wm6.1 ROM´s ?
3. What ROM of wm6 or wm 6.1 should I use ?...preferably a swedish one if there is but also a good stable english one will do :I know there are alot of them but some swedish users may have an answer..
Since the most guides and forum posts are from 2007 I really want to make sure I got this all right. I also plan to write a good guide in english/swedish/german if everything goes ok. So all help would be mucho macho appreciated.
You can also PM me if you like and I´ll be happy to give you more info on how it all goes..
Many thanks
cheers