Related
I have never flashed this phone with any kind of alternate firmware, yet when I go to run the official one from HTC, I get this at 8-% exactly, on 2 diffrent phones:
_______________________________________________________________
ERROR [326]: INVALLID COMMAND
This NBF file cannot be used with for your PDA Phone. Please check you NBF file.
_______________________________________________________________
Then the phone turns into a brick. All it does is show the Tri-Color test looking screen untill try to flash again...
Any suggestions?
What phone do you have?
Whoops....
Sorry... I posted this in the wiz forum and didnt even think to put my phone model....
Cingular 8125
Thank you!
Re: Official Cingular 8125 2.25 Update ---Problem---
pittaman said:
I have never flashed this phone with any kind of alternate firmware, yet when I go to run the official one from HTC, I get this at 8-% exactly, on 2 diffrent phones:
_______________________________________________________________
ERROR [326]: INVALLID COMMAND
This NBF file cannot be used with for your PDA Phone. Please check you NBF file.
_______________________________________________________________
Then the phone turns into a brick. All it does is show the Tri-Color test looking screen untill try to flash again...
Any suggestions?
Click to expand...
Click to collapse
If you are attempting to flash the official ROM on an 8125 and getting this error, there's some bad juju goin on.
Just to be sure, you got the following ROM, correct?
http://www.htcamerica.net/support/software_downloads_8125.htm
I’ve downloaded that so many times my browser is upset at me. There must be a lot of bad JuJu... because It has tanked 2 different phones.....
I’ve taken your 2.3 update, and ran it... It went though... got to 98 and turned red on the phone... finally went to 100% and rebooted... but it was still at 1.8... but at least the phone works again... I really need the push e-mail though... and would prefer to use the official update... or a close derivative..
You should CID unlock first before you apply any ROM found in this forum.
If your phone is virgin, i.e. never been updated to a non official ROM, you will be fine going from 1.8 to this ROM and you would not need to CID unlock. I have gotten an nbf error before, but it was from an attempted downgrade to the stock 1.8 ROM from Summiter's 2.17 release.
Check your OS version and report back.
I know it says you have never upgraded before... If you're still having problems, just take it back to the store, we bricked a phone stuck on the 2.17 ROM and returned it with no problems. Apparently the 8125 does not like animated themes (not my idea, but it did have entertainment value).
Could there be something up with my PC if it bricked 2 seperate phones? WOuld it be possible to fix em with a diffrent PC? and do you think a Cingular store would update the firmware on the phone if it wasnt broken already?
pittaman said:
Could there be something up with my PC if it bricked 2 seperate phones? WOuld it be possible to fix em with a diffrent PC? and do you think a Cingular store would update the firmware on the phone if it wasnt broken already?
Click to expand...
Click to collapse
There's always the possibility of a virus causing issues, but it's exceedingly remote.
If the phone is working you should be able to bring it into any Cingular store and have them do the update for you.
pittaman said:
Could there be something up with my PC if it bricked 2 seperate phones? WOuld it be possible to fix em with a diffrent PC? and do you think a Cingular store would update the firmware on the phone if it wasnt broken already?
Click to expand...
Click to collapse
I concur with gamescan that it might be a virus, or some crappy spyware. I don't think however that you've "bricked" your phones as you WERE able to install sumitter's 2.23 OK. Of course since you didn't SID unlock you didn't get the full upgrade. I disagree with those who insist that you don't need to unlock. Mayhaps you don't need to but I know that sumitter and the other ROM gawds here have always suggested so. If I was you I'd downgrade to the 1.05, unlock, then upgrade. I'd also scan your PC with Spybot, maybe AdAware. Also I'd delete my temp files, in the c:\documents and settings\%username%\local settings\Temp. Also empty your temporary internet files. I've seen large temp folders on PC's create all kinds of grief. Just a suggestion.
Steven
chow
Well... I appriciate all your help thus far.
I called Cingular Yesterday ant they sent out 2 replacement phones for free, and I got them today... With the update already in place, so I dont think I'll be playing with unlocking again LOL... But this information is very helpful, as my Uncle has the same phone and needs the push email more than I do. If his phone gets toasted, Ill be here with the results...
Thank you all very much... this is my new favorite place!!!
Not A virus .... its the phone
Apparantly the newer phones have a new flash chipset G4 which is not compatable with the current crop of cooked roms on this site. I think summiter has one that will work but it didn't work for me. I returned my phone for a replacement hoping to get the g3 chipset but to no avail all the new ones are G4 and are unable to be flashed to the custom roms. also you should be able to sim unlock with no issues but to cid unlock you may need to look elsewhere
Re: Not A virus .... its the phone
alynch75 said:
Apparantly the newer phones have a new flash chipset G4 which is not compatable with the current crop of cooked roms on this site. I think summiter has one that will work but it didn't work for me. I returned my phone for a replacement hoping to get the g3 chipset but to no avail all the new ones are G4 and are unable to be flashed to the custom roms. also you should be able to sim unlock with no issues but to cid unlock you may need to look elsewhere
Click to expand...
Click to collapse
First, the OP was using the OFFICIAL CINGULAR UPDATE not a custom Rom.
Second, He was upgrading from 1.8 which is a 1.x Rom, this means his phone is indeed a G3 variant as the 1.x Roms only have G3 IPL/SPL.
I had this same experience from a virgin HTC 8125....
I had stop all apps running and recharge my battery. Then disable my sleep and screensaver then it worked.
I recently attempted to update the ROM in my Cingular 8125. The process stopped at 95% and I received an "Internal Error". Now, when I turn on the phone, it gets as far as the color RUU screen, and nothing else.
How can I find out if I can repair this situation myself or if I need to take it back to Cingular.
Hopefully you'll give Cingular a little more info regarding this than you gave us.
My psychic advisor is STILL on vacation so I can be of very little help to you, sorry!
What ROM were you running before and what ROM were you trying to flash it with? Did you CID unlock before you flashed?
Sorry - When I posted the 1st message, I was in a hurry...
I am not sure what ROM version was on the device before I attempted to update (I know, I should have paid attention, but I was not). The phone was new from Cingular and I had not done anything else to it besides load a couple of apps (Skype & Agile).
I attempted to run the file RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship.exe that I downloaded from the HTC site. The update go to 95% and I received the error "ERROR [326]: INVALID COMMAND" - This NBF file cannot be used for your PDA Phone. Please check your NBF file." (I have attached a screenshot of the error to this post).
I am not sure what to do at this point.
Thanks,
Chris
Some folks at the Cingular forum are having the same issue with no solution offered.
I'd suggest putting the device into bootloader mode (Holding Record and Camera buttons while soft reseting) and then reflashing. Make sure not to launch any programs while flashing. I also don't touch the device at all as I've noticed the USB connection might slightly disconnect.
Good luck and let us know what happens.
I just tried reloading from the bootloader screen - no luck. Exact same error at 95%. Would it work to try to reload an original earlier ROM? If so, how would I go about trying that?
Chris
I had this same problem.....I went to the cingular site after having the problem. Before installing I stopped all applications then soft reset.
THen after it boots up install the file from cingular. It worked from their site. Not sure what changed but I am not having any problems now with the new ROM.
I had this same problem.....I went to the cingular site after having the problem. Before installing I stopped all applications then soft reset.
THen after it boots up install the file from cingular. It worked from their site. Not sure what changed but I am not having any problems now with the new ROM.
I have re-downloaded the ROM file from the Cingular site (actually it just redirects to the HTC site). Same problem. I cannot get to the point to even shut down any programs because the phone OS does not even load at this point. When I do a soft reset, I get the following (sorry for the blurry image - as you can see my good phone with the good camera is dead...)
I had a similar problem. I posted the fix on another thread and ppl said i was wrong, this wasnt it...but heres what worked for me.
Are you using a usb port on the front of the computer? if so, try pluggin into the ports on the back of your computer. I tried flashing the official rom from cingular a few times using front port and it stopped at the exact same % each time. got the same thing as you, colored bars.
Someone had mentioned to me that front usb ports don't work as well as back ones. give it a try. good luck
from the picture, it looks you have the G4 chip(u can see 2.25 0001)
Thanks to everyone for their input. From the suggestions above, I have tried various USB ports on my laptop and I always get to the same point. I have also called HTC tech support and they are pretty sure I have bricked my phone. I talked to Cingular and they have agreed to replace it. I have also researched the G4 chip issues (looked at the post: http://forum.xda-developers.com/viewtopic.php?t=56408).
Now I have the following question - When I get my new phone (which I will assume will have the G4 chip as well), the Cingular rep told me that it will already have the latest 2.25.0001 ROM on it. What are my options at that point to SIM unlock my phone. Will I be able to? From the post I referenced above, it sounds like I may not be able to with the G4 chip.
Chris
xtreme23 said:
from the picture, it looks you have the G4 chip(u can see 2.25 0001)
Click to expand...
Click to collapse
I second this observation! :shock:
This makes a major difference on wether or not you can even upgrade.
Search for G4 issues.
The .0001 in the IPS/SPL number will tell you which one you have.
The way I understand it is:
2.25 - G3
2.25.0001 - G4
I think this is the proper way to identify it.
slapper said:
Now I have the following question - When I get my new phone (which I will assume will have the G4 chip as well), the Cingular rep told me that it will already have the latest 2.25.0001 ROM on it. What are my options at that point to SIM unlock my phone. Will I be able to? From the post I referenced above, it sounds like I may not be able to with the G4 chip.
Chris
Click to expand...
Click to collapse
Chris, LokiwizMSL ( http://forum.xda-developers.com/viewtopic.php?t=50768 ) can SIM Unlock your device. Be sure to read the instructions.
Well - Now I have a new problem. So far, Cingular is refusing to replace my phone - saying that the ROM upgrade voided the warantee. I am still fighting that, but just in case I loose, is there any way to get my phone fixed once it has been "bricked"?
slapper said:
Well - Now I have a new problem. So far, Cingular is refusing to replace my phone - saying that the ROM upgrade voided the warantee. I am still fighting that, but just in case I loose, is there any way to get my phone fixed once it has been "bricked"?
Click to expand...
Click to collapse
If you installed an unofficial ROM then they are correct. You should never admit that you used a ROM that was not provided by HTC.
There are warnings all over this site about VOIDing your warranty.
Since you used the Official Update they are wrong.
Same problem with official Cingular 8125 ROM
I tried to flash the official Cingular ROM from the HTC site here:
http://www.htcamerica.net/docs/RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship.exe
I got the same error at 95%:
"Error [326]: INVALID COMMAND This NBF file cannot be used for your PDA Phone. Please check your NBF file."
When I reset the phone I get the RGB bootloader screen and nothing else.
My phone is a G4 and was running ROM version 2.25.11.1 WWE before. The reason I tried to apply this ROM is because there was apparently no Extended ROM. None of the customization cabs executed on a hard reset. Also, in Device Information, there was no "ExtROM" listed.
This is the second phone that this has happened on. I thought the first time was just a fluke thing and I had a bad phone. But now I think there is an issue with this ROM.
Anyone have any idea what is going on here with this ROM? Does the fact that there was no Extended ROM have anything to do with this ROM not flashing properly?
Is there anything else to try or do I need to try to return the phone (AGAIN)?
how to fix the problem
read this thread carefully. The upgrade problem seems to be occuring on G4 chipped Wizards with the most current IPL/SPL.
http://forum.xda-developers.com/viewtopic.php?t=56088
take the official update. run it, when it finishes extracting look for the extracted NBF file in your
C:\Documents and Settings\yourusernamehere\Local Settings\Temp\the newest directory just made
find the NK.NBF file
extract it using the tutorial in the post above you will be flashing with the official cingular components sans IPL/SPL.
flash it and your are back up and running
I would have posted this earlier but i had to make sure it worked and was repeatable.
I think the problem with the new update is the new IPL/SPL version checking. It seems that if the patcher sees the same version already running it will give you that error at 95%. I've seen it on 3 phones already and I have been able to fix them by doing what i've told you above. You are already in bootloader mode and your phone is ready to accept a new rom anyways. My solution may not be the best for your phone and take no responsibilites but you are already desperate and need a fix. Good Luck!
Thanks for the reply, evilito. Since I hadn't gotten any replies for a few days, I decided to go ahead and try to exchange the phone at the Cingular store. They were baffled that this was the second phone I had returned for the exact same problem, but gave me a new phone anyway. I wish now that I had waited so that I could try evilito's solution to see if it works. As it is now, I am too scared to try any flashing on this new phone after my results with the first two. I would really hate to have to try to return a third phone
Can anyone else verify that there is a problem with the latest Cingular ROM when flashing a G4? Or did I really have two bad phones?
slapper said:
Now I have the following question - When I get my new phone (which I will assume will have the G4 chip as well), the Cingular rep told me that it will already have the latest 2.25.0001 ROM on it. What are my options at that point to SIM unlock my phone. Will I be able to? From the post I referenced above, it sounds like I may not be able to with the G4 chip.
Chris
Click to expand...
Click to collapse
Thats good to know, I thought that when we unlocked it and updated the ROM we lost Warentee Support. Where can you get the official Cingular 2.25 ROM. I am still on 2.17.
i have recently bought a htc p4300. it came with wm5 and as u can tell from the title im tryin to upgrade. i have unlocked the cid using m3000v4unlock from a website. i was told that i have to use it since i have a g4. i have used three different roms for this and all it says after about ten seconds of the upload bar is: error 300, update tool somthing. my goal is to upgrade my phone to an extremely stable wm6 on an american tmobioile network. can anyone lend me a hand. i really need help. also, if anyone can hook me up with a seriously detailed install readme file with the software that would be great.
shastri said:
i have recently bought a htc p4300. it came with wm5 and as u can tell from the title im tryin to upgrade. i have unlocked the cid using m3000v4unlock from a website. i was told that i have to use it since i have a g4. i have used three different roms for this and all it says after about ten seconds of the upload bar is: error 300, update tool somthing. my goal is to upgrade my phone to an extremely stable wm6 on an american tmobioile network. can anyone lend me a hand. i really need help. also, if anyone can hook me up with a seriously detailed install readme file with the software that would be great.
Click to expand...
Click to collapse
Can't you just read the "How to flash a new ROM to your Wizard... a little tutorial!" sticky ?
C'mon, is it that hard ?
i did read the tutorial. but when i put it in tricolor and i use the software to unlock it, it works. then i have to restart the phone, and i open the upgrade software and run the ruu. but when i do it i get to a screen that saws" 300 error" i dont know if in doing it wrong or if its the software im usng
Dear all Kaiser anchestor,
I have a problem with my Kaiser. I really hope that all of you can help me. Ok? Please....
This is the problem :
At the begining, My HTC Kaiser run so slowly, sometimes freezing (Condition WM 6.1 with it's SPL 1.56)
After I read the same problem in jockyw2001 thread, then I tried to flash My device SPL to 3.28 (with the step in front of that thread and the SPL from that thread too)
Flashing the SPL to 3.28 was successfully and my device run fast now
BUT!!! I can't Enabled my WiFi!
Next, I tried to Re-Flash my SPL to 1.56 again, and it's done successfully. But, the WiFi still can't be enable.
Next step, I tried to downgrade the ROM to WM 6, and WHAT!
I still can't Enable my WiFi!
Now, I'd upgrade to WM6.1 again (official ROM from HTC website). But, the WiFi still can't be enable.
The condition when I enable the WiFi is loading then turn off by itself. What's the problem?
I really need all of your help for this.
This is my Device Information:
ROM Version :3.29.707.0 WWE
ROM Date : 05\07\08
Radio Version :1.65.16.25
Protocol Version : 25.83.40.02H
After upgrade to WM6.1, My Bootloader now is:
KAIS130
SPL-3.29.0000
CPLD-8
I'm stress already. Hope all you may spare some of your time for help me to solve the problem. Thanks before. For more detail, just watch the video that I record when tried to enable the wifi.
The url is : http://www.andrylim.com/others/WifiProblem.wmv
Whats wrong with running the HTC upgrade on your HTC original TyTN II?
andrylim said:
After upgrade to WM6.1, My Bootloader now is:
KAIS130
SPL-3.29.0000
CPLD-8
Click to expand...
Click to collapse
Since you're interested in running the official HTC WM 6.1 version on your TyTN II then why not simply run the HTC Upgrade program which will reinstall everything required (SPL, Radio and ROM) in one easy go rather than have to upgrade this and that, bit by bit? If you have an official TyTN II you can get it from HTCs e-Club/Support or you can also download it from the XDA Kaiser Wiki ROM page. Note that my SPL is 3.28.0000 and thats all through the official upgrade path so maybe your SPL has something to do with it? See if the official upgrade installs on your device otherwise you'll have to revert to the correct SPL before trying again. Note that the newest WWE ROM upgrade now also comes with a (slightly) better radio as in my sig. Remember to take your sim and memory cards out before attempting the flash.
***Edit*** Just realised you're running the SEA rather than WWE HTC ROM I'm using so yes 3.29 looks to be the right SPL for your ROM, the rest still applies though.
Hmm...
Sorry Mr Flying Kiwi, I think you didn't read the message completely. I've already re-flash from OFFICIAL ROM WM6.1 from HTC e-Club. But, the same problem. It's not fix yet. I've reflash over than 5 times, downgrade to WM6 over than 2 times. an the result is the same. My WiFi Cannot be enable. I hope you can play the video that i record from the links up there (440kb only), so you will know my problem.
Thanks for your reply Boss!
or this one
The url is : http://www.andrylim.com/others/WifiProblem.wmv
Flying Kiwi said:
Since you're interested in running the official HTC WM 6.1 version on your TyTN II then why not simply run the HTC Upgrade program which will reinstall everything required (SPL, Radio and ROM) in one easy go rather than have to upgrade this and that, bit by bit? If you have an official TyTN II you can get it from HTCs e-Club/Support or you can also download it from the XDA Kaiser Wiki ROM page. Note that my SPL is 3.28.0000 and thats all through the official upgrade path so maybe your SPL has something to do with it? See if the official upgrade installs on your device otherwise you'll have to revert to the correct SPL before trying again. Note that the newest WWE ROM upgrade now also comes with a (slightly) better radio as in my sig. Remember to take your sim and memory cards out before attempting the flash.
***Edit*** Just realised you're running the SEA rather than WWE HTC ROM I'm using so yes 3.29 looks to be the right SPL for your ROM, the rest still applies though.
Click to expand...
Click to collapse
Use the official upgrade package - not just the rom file
andrylim said:
Sorry Mr Flying Kiwi, I think you didn't read the message completely. I've already re-flash from OFFICIAL ROM WM6.1 from HTC e-Club.
Click to expand...
Click to collapse
I read it alright but as you've not done it *using the officially supplied HTC upgrade package (not just the ROM file within it from HTC e-Club)* I reccomend you give that a try. No special hard spl version is reqd and as long as you have an official ROM to start with and you're upgrading or reinstalling the same ROM version, it's simply a case of running one file and following the instructions. Once you've got the reflash to run that way and completed the process, simply hard reset and then test your Wifi before installing anything further.
But, the same problem. It's not fix yet. I've reflash over than 5 times, downgrade to WM6 over than 2 times. an the result is the same. My WiFi Cannot be enable. I hope you can play the video that i record from the links up there (440kb only), so you will know my problem.
Click to expand...
Click to collapse
Perhaps the capturing program over Activesync may be interfering with things (but I did view your wmv). What I am sure of is that if you have the correct ROM matched to your device and correctly installed with the right spl and radio, Wifi should work fine. Running the official upgrade is the easiest way to get this but if there is something non-official about your current setup, the upgrade program may refuse to run. Let us know if that happens. It's clear that you didn't do this in the beginning because you ended up with the wrong spl version for your rom so it's time to do it the official 'HTC Customer' way.
Hahaha.... thanks for your information. I'd tried yesterday. And still no response. ugh.... Btw, I've read from another thread (Athena). They said that someone ever got a problem like this. The cause is the WiFi MAC Address is missing/erased? Is it possible? I thought that MAC Address is a serial number of WiFi such as an IP, where saved in WiFi chip/device and cannot be erase. If do so, how to set an MAC address to the WiFi module? Do you have an idea? I'd tried to have a silly search about that address in Registry, but I cannot find any key that sounds about MAC Address. (Mac Gyver maybe?)
Flying Kiwi said:
I read it alright but as you've not done it *using the officially supplied HTC upgrade package (not just the ROM file within it from HTC e-Club)* I reccomend you give that a try. No special hard spl version is reqd and as long as you have an official ROM to start with and you're upgrading or reinstalling the same ROM version, it's simply a case of running one file and following the instructions. Once you've got the reflash to run that way and completed the process, simply hard reset and then test your Wifi before installing anything further.
Perhaps the capturing program over Activesync may be interfering with things (but I did view your wmv). What I am sure of is that if you have the correct ROM matched to your device and correctly installed with the right spl and radio, Wifi should work fine. Running the official upgrade is the easiest way to get this but if there is something non-official about your current setup, the upgrade program may refuse to run. Let us know if that happens. It's clear that you didn't do this in the beginning because you ended up with the wrong spl version for your rom so it's time to do it the official 'HTC Customer' way.
Click to expand...
Click to collapse
More specifics needed
andrylim said:
Hahaha.... thanks for your information. I'd tried yesterday. And still no response. ugh...
Click to expand...
Click to collapse
I was offering serious advice not pulling your leg. Now, when you say 'still no response yet' - precisely what do you mean (exactly what did you try and what happened)? I've flashed my Kaisers ROM a couple of times now using HTC official ROM upgrading packages and it's gone perfectly fine. As far as the MAC address goes, I know there are ways of changing it (because there is an extremely small possibility that you may end up with two identical MAC adresses on the same network and this will cause problems) but this won't be the culprit in your case. I think (again) the first thing to do is to use the official package (and only that - no additional tools/utilities are reqd) to get everything in order and let us know how that goes and what versions of everything you end up with.
This is the information that appears in my device now after re-upgrade the official ROM from HTC e-Club:
File name : RUU_Kaiser_DOPODASIA_WWE_3.29.707.0_radio_sign_25.83.40.02_1.65.16.25_Ship.exe
KAIS130
SPL-3.29.0000
CPLD-8
ROM version : 3.29.707.0 WWE
ROM date : 05/07/08
Radio version : 1.65.16.25
Protocol version : 25.83.40.02H
Btw, may i ask a question? I found something strange about a MAC address. Yesterday I'm not intention open the "Wireless LAN" from Settings > Connections > Wireless LAN
In Advance tab, there are Status, MAC, and IP. My Question is is the MAC address serial appears even you didn't enable a WiFi? In my device it's empty.
Btw, bro... I've been search a problem like this in this website. I've found the same problem in Athena thread. They said that the MAC address is missing, but some one make a fix but only for Athena.
this their URL: http://forum.xda-developers.com/showthread.php?t=387454&highlight=Athena+WiFi+Problem&page=5
Thanks & sorry if i waste your time in solving my wifi problem
Flying Kiwi said:
I was offering serious advice not pulling your leg. Now, when you say 'still no response yet' - precisely what do you mean (exactly what did you try and what happened)? I've flashed my Kaisers ROM a couple of times now using HTC official ROM upgrading packages and it's gone perfectly fine. As far as the MAC address goes, I know there are ways of changing it (because there is an extremely small possibility that you may end up with two identical MAC adresses on the same network and this will cause problems) but this won't be the culprit in your case. I think (again) the first thing to do is to use the official package (and only that - no additional tools/utilities are reqd) to get everything in order and let us know how that goes and what versions of everything you end up with.
Click to expand...
Click to collapse
andrylim said:
This is the information that appears in my device now after re-upgrade the official ROM from HTC e-Club:
File name : RUU_Kaiser_DOPODASIA_WWE_3.29.707.0_radio_sign_25.83.40.02_1.65.16.25_Ship.exe
KAIS130
SPL-3.29.0000
CPLD-8
ROM version : 3.29.707.0 WWE
ROM date : 05/07/08
Radio version : 1.65.16.25
Protocol version : 25.83.40.02H
Click to expand...
Click to collapse
That looks right to me but if you haven't yet ran the upgrade file above to flash to ROM you need to do it the official way and try that. If Wifi is still behaving as in your video do a hard reset and try again (before loading any additional software).
Btw, may i ask a question? I found something strange about a MAC address. Yesterday I'm not intention open the "Wireless LAN" from Settings > Connections > Wireless LAN
In Advance tab, there are Status, MAC, and IP. My Question is is the MAC address serial appears even you didn't enable a WiFi? In my device it's empty.
Click to expand...
Click to collapse
In mine it's empty too but if you go back in after enabling Wifi, theres a MAC address in there. I really don't think your problem has anything to do with the MAC address but if you've tried all of the above and still can't get it working, as you appear to have an official setup, it's time to contact Tech support and get them to go through some checks over the phone with you. Maybe someone else has thoughts on this......
Hahaha... thanks. Btw, I have another problems.
I bought this device from other country (Singapore). My friends said, the Singapore HTC can view the device history. They can see if the device already being flash how many times and anything unofficial program such as SPL or radio, then the warranty wil be void. Because, my friends already have such a problem also with his device Dopod U1000 (Even he revert to his original SPL or radio).
I think i should throw this device or sell it out and buy the new one. Hiks...
Flying Kiwi said:
That looks right to me but if you haven't yet ran the upgrade file above to flash to ROM you need to do it the official way and try that. If Wifi is still behaving as in your video do a hard reset and try again (before loading any additional software).
In mine it's empty too but if you go back in after enabling Wifi, theres a MAC address in there. I really don't think your problem has anything to do with the MAC address but if you've tried all of the above and still can't get it working, as you appear to have an official setup, it's time to contact Tech support and get them to go through some checks over the phone with you. Maybe someone else has thoughts on this......
Click to expand...
Click to collapse
andrylim said:
I think i should throw this device or sell it out and buy the new one. Hiks...
Click to expand...
Click to collapse
Doesn't it make sense to at least try what's been suggested first? What have you to loose? The hardware company have no need to know what 'ROM Action' has occurred in the past and who knows what any people you've leant your TyTN II to may have done with it..... They only need to know how it is now and whether it's currently official (ie flashed using the HTC upgrader).
andrylim said:
I think i should throw this device or sell it out and buy the new one. Hiks...
Click to expand...
Click to collapse
I'll give you $50 for it.
The same problem
Im having the same problem... my wi-fi do not turns on! I have flashed this a lot of times, and sometimes works, sometimes dont.
Does anyone have any ideia about this? im stressed becouse i have the same problem... could anyone tellme a good radio in order to try to solve this issue? thanks
Wi-Fi issues
This has worked for me, dont know if its the same case with you or not.
My device was never able to connect to my Wifi n/w at home. If I went to start -> setting -> connections -> Wifi, it would show my home n/w as available, when I tried to connect to it, the status changed from Available to "connecting" then became available again.
In my home n/w I had access type authentication as WEP keys + Mac address filtering. My device was added to the MAC address list so that was not a problem. The issue was access point authentication which was set to WEP keys type authentication on my router. Once I changed from WEP keys to WPA-PSK (data encryption type TKIP) my WM was able to connect to the router.
I have HTC tytn II and its wifi is not searching any other wifi devices or router even in very close range , but wifi is turning on and the green light is also blinking
So, is there a hardware problem?
I did 3.29 hard spl , hard reset ,hard spl 3.34 , but the result is same.
and in network adapters IEEE 802.1b/g goes down and down in the list of network adapters , please HELP.! and sorry for my bad english
try a newer radio
mfsr98 said:
try a newer radio
Click to expand...
Click to collapse
Currently the Radio Version is 1.70.18.02
before this Radio Version I had 1.65.*.*
Ok, so I tried installing the WM6 rom on my device without knowing it was in fact a Harrier and not a Blue Angel. I now realize I was very stupid in doing this. Now when it boots I get the stripes on the screen and "No GSM, D 5.60.00 WWE" written in the bottom right corner of the screen.
Does any one have an original Harrier rom they could upload so I can flash it back to the original WM2003?
If no one has that, is there a way to copy the rom from another, identical device?
xplode has a great firmware archive, where you can find about any original shipped rom, for the harrier, you find it here: http://firmware.atspace.com/Harrier.html
Thanks Chef_Tony. Thats got it working again perfectly.
i have the same problem it now says no gsm ....
what software do i need to make it work again ?
thx
andy
gripperwod said:
i have the same problem it now says no gsm ....
what software do i need to make it work again ?
Click to expand...
Click to collapse
Hit the link that Chef Andy listed, find your carrier in that list and download the latest one available
what i meant is which 1 do i download from the link chef andy left do i just use the upgrade tool or radio if so how do i find out which version i need ?
thanks
andy
gripperwod said:
what i meant is which 1 do i download from the link chef andy left do i just use the upgrade tool or radio if so how do i find out which version i need ?
Click to expand...
Click to collapse
Again, find your carrier (I'm assuming that the phone was running the official ROM that it shipped with for your carrier) in that list and download the latest one available. No one can tell you which one to download as no one else but you knows who your carrier is.
The radio version doesn't matter in this situation as the OS is coded to deal with a CDMA radio stack, and most, if not all, official ROM flashers will flash the radio stack with the OS. You are going to have to flash it back to whatever OS and build (usually WM2003 for the Harrier) is provided in the archive. If there are multiple versions of the ROM/radio available, generally the newer ones are the better ones.
You shouldn't need anything special for this as you will be flashing the official ROM for the phone. Download, run the executable and follow the on screen instructions.
ok ive downloaded all from these links and it tells me each flash ..
the rom image is not designed for your device . error code is wrong country code !!
i tried simunlock and now have no gsm showing in boot .
it was on uk orange network the phone is spv m2000
thx
well, your device is a blueangel, this thread is about the harrier. it deals with people trying to recover their CDMA devices after a bad flash, you have a GSM device, a completely different phone, and also, the source of your problem is not the same. thank god, the flash did not work, or your phone would be bricked for good.
you need to do a completely different procedure:
1. you go to xplode's BLUEANGEL firmware archive at http://firmware.atspace.com/Blueangel.html and download any rom in your language / from your country. then you put your device into bootloader mode and flash the device using maupgradeut_noid, found here: http://rapidshare.com/files/322928773/Chef_Tony_RUU.zip
2. then, when you have wm2003 back, please post back for further steps to go.
thank you i will do as you said and report back thx mate , ps are you realy a chef because i am lol i have been a chef around 26 years.
ok downloaded the orange uk but its file is corrupt so executable failed ...
looks like im not going to win ..
tried other orange uk files further down the list but still says country error code.
yes, the country id error is the reason, why you need to extract the 40mb exe file, put maupgrade in there, from the link i provided earlier, another thing to avoid the country id error, is to put the device into bootloader mode before starting the upgrade process, so, before you put the blueangel into the cradle, you press record+power+reset, until the display shows "Serial" and "V2.0x" where x is a number from 5 to 7, then you connect the device and start maupgradeut_noid.exe, which has to be in the same folder as the nk.nbf and all the other needed files. using the maupgrade instead of the BAupgrade and using the bootloader mode avoids nearly all the errors, like country id, device id and so on.
EDIT: btw. i am not a chef, i am a system administrator, the avatar and username are just my regular online name, named after the most ridiculous chef on american tv ^^
gripperwod said:
thank you i will do as you said and report back thx mate , ps are you realy a chef because i am lol i have been a chef around 26 years.
Click to expand...
Click to collapse
Tony is right, your phone would have been bricked.
For future reference, when you post, make sure to list your carrier and the exact model of phone. Anyone in these forums needs this info to attempt to offer the correct information to help.
In my posts, as Tony mentioned, this thread was dealing with Harriers, the CDMA version of the Blue Angel. When you jumped in, I thought that you were talking about a Harrier as well.
Keep in mind that each phone has it's specific ROM designed for that single model of phone alone, they are not interchangeable.
hi
after long time thought i might have another go ...
all the links you have supplied dont work eg: file is corrupt is the message im getting when trying to install software to pc.
i need the factory cd rom for the : orange spv m2000
i have no gsm on the phone since i upgraded the phone to wm6.5
ce os 5.2.21169 (build 21169.5.0.0)
please help
thx