I was trying to flash my trinity but i am having problems,
I can get the phone into the bootloader mode without any problems
and the software see the phone ok but the update only gets 1% before it fails with "error 270 image is corrupt" i have tried many different image but the same occurs with them all.
My phone now only goes to the splash screen
is there any think i can do?
take a look at this thread, it may help you unbrick your Trinity...
thanks but no , my phone is not stuck in the bootloader just will not flash
Go HERE they might have a solution there!
Please don't double post! It will not give you a solution twice as fast
Hi. I had the same issue and solved it. feel free to send a MP if you still need help
Thanks still can not get working.. sent a pm to tonio94 thanks mate
Error 270
Hi m8,
Your error 270 is because your phone is still locked and the ROM(s) you are trying to flash are not natively signed for use on your particular phone!
You can either...
1. Pay to get your phone unlocked
2. Set your phone with Hard-SPL (see the related sticky on this very Forum)
3. Extract the .nbh file from the ROM you are trying to flash and flash it using the SoftSPL (SSPL) - again see the sticky on this very Forum.
Not being funny, but you really must do a bit of background reading before you start messing with these new ROM's on your phone.
I hope this helps - PM me if you need more detail.
Moz.
Same problem
Hello,
I've followed the thread to unlock cid/sim my 3600, but I can't upgrade nothing. I can't upgrade hardspl to.
With all roms, the phone stay on tricolor screen after "Yes" to allow enterbootloader.exe, and the rom tell me that the device is not connected.
Active sync was ok, the phone battery to.
Help?
I've 1.23.406 rom actually, and spl 1.07 ds.
EDIT: I've the soluce. I use the SSPL-TRIN for each upgrade, before the hard spl, before passing in 1.41, et now before the ROM, and it runs!!
I had not understood the thread about sspl-trin to bypass, so I didn't use properly.
Now it's ok...
Related
I have a stuck image on my 8125. The phone "boots" but only shows a white screen, and is unusable.
The "a2sd all" restore option mentioned in the forums doesnt work for me. I have read on several forums that I should be able to reflash the OS from the bootloader, though I cant find any instructions on how to do this
Could someone point me in the right direction for how to flash an OS VIA bootloader?
Thx
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Mirek - not to be totally ignorant, but the step 4 is what I'm having problems with .... where can I find either a providers ROM, or something that I can actually use while in bootloader mode?
Thanks!
NM ... Found it!
For anyone reading this .... You can get the provider ROM for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
Thanks for your help!
mirekluza said:
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Click to expand...
Click to collapse
Dear Readers,
I'm having problem with my Dopod 900(,Qtek 9000,HTC Universal,O2 Xda Exec,Jasjar ). Can somebody please tell me what to do?
Before this, every time somebody called, the PDA lost the network bar and start to search or network and reject the calls automatically and also i wasn't able to send SMS. Now, i tried to install WM6 crossbow, the phone even cannot be on !!! even when i connect it to the charger, even the light will not be on. the only page that i can see is a white page asks Press 0 to Restore factory default or press X to exit. either perss 0 or X, the phone will be off and i cant turn it on with power key....
Please tell me what can i do ?? I really need your help.
PLEASE REPLY, PLEASE.
[email protected]
Warm Regards to All
G-Jorji
brick?
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
WHAT did you downgrade from?
Did you re-unlock your G3?
How's your battery?
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
IPL/SPL 2.08? Does that exist? Do you mean 3.08?
Are you sure your device is a G3? Or you killed it when flashing Button's ROM?
plz help me .after i try to hard spl my phone ( i did it wrong way) i am stuck in boot menu
i download several rooms but it give me error 300 and a message say get a newer update utility
my original room was ger and orange
where can i find such room plz help me
this is another story of bricked Herald device
there's no solution for that you have to wait
halder said:
plz help me .after i try to hard spl my phone ( i did it wrong way) i am stuck in boot menu
i download several rooms but it give me error 300 and a message say get a newer update utility
my original room was ger and orange
where can i find such room plz help me
Click to expand...
Click to collapse
what part is it stuck on, the white screen?
Provide more information
hey bro, he's saying about error 300, pls get newer update utility
flash area is screwed so you may think in a customized ruu update to ignore cid check and get your phone on
my friend updated it he didint install the 3 cab before doing the ruu utility .he stuck in white screen for long time then ..we are in bootloader menu now...
error 300 is beyond my knolage
plz help how to custimize the ruu ..
i know how to do it for wizard but not for herald is it the same way or there another way ..
thank you in advance
htc p
ipl 1.08.0001
spl 1.08.0001
model hera100
bro.. error 300 means "supposed" you have to flash your device with a newer flash tool (newer? there's no newer utility!) so we have to find the way to recover OS part first- I think by recovering OS and booting up device again we can find a way to recover CID area and unbrick our devices
the problem is, nobody wants to help
jockyw2001 --> he's a great coder/programmer but he doesnt look for those areas
Olipro --> he didnt say a word about that. We're expecting hardSPL unbrick tool
POF --> no words too
so, these are the 3 great programmers here, but no words from them.
What can we do? I think nothing... Bcoz Im stucked in "Invalid Certificate" screen and no reply from anyone... I think the brick problem here is from everyone cuz we dont get any reply
Pls.. I know we get devices from several months ago.. I think we can get all opinions, suggestions, everything and get herald unbricker.. come on!
tramuyo.... while your answer is technically correct, theres a better answer.
From what i understand, he attempted to flash a custom rom via hardspl or USPL. This is a no-no if the SPL is lower than 4.
so for now my phone is bricked .
i tried to flash it with my original rom. still error 300
.thank you guy for u replay
the problem is, we need Olipro help to get our devices recovered. At least, recover OS part
true. maybe we can somehow lure him into the forum. let's assume he searches his name on a semi-regular basis (i do, but i digress)
Olipro Olipro Olipro Olipro Olipro Olipro Olipro Olipro Olipro Olipro
thats probably enough
Olipro doesnt reply our messages. I think he have the clue to solve our problems, but i dont know why he doesnt want to publish it or something
can we start to donate for man who can solve this problem?
can we start to donate for man who can solve this problem?
i can donate 100$
me too
just help as we will do evey thing
till now my phone is in bootloader menu
no can do
but i heard that if i hard spl it it will work is it correct.
any idea
i have also such problem. 1st i have make hard spl and write patched rom in to p4350. after i try 2 write oficial rom and got only boot menu.
as i understant the only solution 4 it is writing native rom on it but problem is that i dont know what rom was there before. my mistake . another problem is that hard spl works only in normal mode via instaling cab files and patching spl. so does exist hard spl 4 this model which is writing via boot mode or patching rom whithout cid checking?
I don't know if there's anything you can do, but try this. It hasn't been tried on the Herald, that I know off, but it's worth a try.
halder said:
till now my phone is in bootloader menu
no can do
but i heard that if i hard spl it it will work is it correct.
any idea
Click to expand...
Click to collapse
This is a wild guess, but if your able to get to the boot menu.
What about trying to download a micro rom and copy it over to your sd card.
Then perform a soft reset as you would to enable the boot loader menu.
I think it's worth a try.
has there been an update on how to exit from a tri-color bootloader screen?
I ran into this problem today and have searched for hours with no clue as to a way to resolve the issue.
I notice also that right before the tri-colored screen appears I see a flash of a white screen and I believe it says it cannot detect SD card... if that helps
I encountered this problem only after having flashed to the new 7.7 open touch and my phone no longer being recognized on my PC for activesync
problem (300) bootloader
I have problem the same. exists somebody that helps me? urgent
i have same phone hera100 and same problem still in tricolour display.how solve this problem
b.r
bahri
I am new to completely flashing a custom ROM. I've been trying to flash a new ROM on my tilt, with the latest AT&T updates(ROM 1.62.502.0 Radio 1.27.14.09). Each time I try to flash a custom ROM I get Error 262 Update Error. The progress bar never gets past 0%. I've tried multiple PCs and tried reinstalling ActiveSync. Am I missing something, or do I have to do something first before being able to flash the new ROM?
Any help is greatly appreciated!
Steve
i suggest u read all the wiki's and stickies regarding flashing a custom rom before taking any action...u obviously havent read it or havent got a good understanding of it which is why ur getting this error...and btw..i also suggest u search for solutions rather than just posting a thread like this which can be answered through a brief search of the forums.
I am about 100% sure you searched, didn't you?
Here, baby boy, let me spoon feed you and you can ask your mommy if she can whipe your drool:
http://www.digwin.com/view/schaps-wm6-pro-roms-update-error-262
bapssystupr3m3 said:
i suggest u read all the wiki's and stickies regarding flashing a custom rom before taking any action...u obviously havent read it or havent got a good understanding of it which is why ur getting this error...and btw..i also suggest u search for solutions rather than just posting a thread like this which can be answered through a brief search of the forums.
Click to expand...
Click to collapse
I have searched the forums over the past week or so. The solutions suggested such as soft reset, hard reset, reinstall activesync, switch USB ports, etc have not done anything. I also came across this thread:
http://forum.xda-developers.com/showthread.php?t=370205
which would suggest that I there is an incompatibility. I was hoping someone could point me in the direction of which radio version etc I would need to update to in order to update to a WM 6.1 ROM.
edit:yes I have run CID unlock.
Steve
AT&T 1.62.502.0 w/ 1.27.14.09 radio should flash fine on any Tilt even without CID unlock, since it's signed by AT&T. While I'm glad to hear your phone is CID unlocked, it's still strongly suggested that you flash HardSPL & Security Unlock your device.
Regarding your current issue, have you:
* Tried another computer to flash from?
* Entered tri-color bootloader mode on your phone prior to flashing? You can find out how to on the wiki.
Hope this helps!
_Alex_ said:
AT&T 1.62.502.0 w/ 1.27.14.09 radio should flash fine on any Tilt even without CID unlock, since it's signed by AT&T. While I'm glad to hear your phone is CID unlocked, it's still strongly suggested that you flash HardSPL & Security Unlock your device.
Regarding your current issue, have you:
* Tried another computer to flash from?
* Entered tri-color bootloader mode on your phone prior to flashing? You can find out how to on the wiki.
Hope this helps!
Click to expand...
Click to collapse
Thanks Alex! Tri-Color mode worked!
Steve
My error 262 fixed
I don't know if this is the best place to put this, but I didn't want to open a new thread.
I too had been getting repeated error 262. And I spent a couple of hours searching for answers, and while there have been many questions raised on this subject, there have been few clear solutions (and certainly none that worked for me).
I have the HTC branded Kaiser installing from Vista. (By the way I am new to this, but as I had such a hard time working this out, I thought I should at least post what worked for me.) I unlocked the CID with pof's Hard-spl v1 tool. Then (as I want to stay with Mobile 6.1) I upgraded the hard spl to v3.28 by JockyW. I then downloaded a number of Roms I wanted to try. That is where the trouble started.
Each ROM I tried would get past the tri-color screen with no problem. Then it would hang at the 0% until finally showing the error 262. A soft reset would reload my previous rom unchanged. I tried many things: removing all USB's, firewall, virus protection, hard reset, reboot windows, every suggestion I could find (and understand).
While the hard spl I had should have worked, I thought I should try version 3.29. When trying to upgrade to that I had a similar problem with error 260 this time. Looking over spl update instructions I realized I had forgotten to uncheck "disable usb connections" in "Activesync" at the proper stage. Once that was unchecked, the new spl loaded. After that I was able to load the cooked roms with no problem.
It appears there was something wrong with the HardSPL v3.28 I was using or in how I installed it. The tricolor screen was showing 3.28. In any case, after I reinstalled a new hard spl (this time 3.29), I had no more error 262.
A bit long-winded, but hopefully this might help someone else.
I think I've been a total idiot and messed up my HD. I hope there's a way to salvage the situation!
I was attempting to flash a 1.56 ROM so tried to downgrade to SPL 1.54; this was going along nicely until it encountered an error and tried to re-start the flash. Now the device is stuck on "Loading..." before begining the flashing process.
If I soft-reset the device, the SPL has changed to 1.54.0000 according to the Bootloader screen but it says "Upgrade ROM code error Please try again".
I've googled that error message and found a few hits but none of them presented a solution; just people asking this question.
Since that, I've tried to Hard-Reset but it brings me back to the same Bootloader error.
I've tried to flash a ROM but the device can't connect to Activesync to use the RUU_Wrapper and flashing via the BLACIMG.nbh on my SD card won't work either; it just goes back to the same Bootloader error screen and gets stuck on the "Loading..." again.
I've also tried to flash the new HSPL which is 1.56 capable but that suffers the same problem.
Anyone have any suggestions? Please? Never encountered anything like this in years of flashing my Blueangel and Tytn.
Full details from my bootloader screen:
RUUNBH
BLAC100 32M
SPL-1.54.0000
MicroP-Blackstone (LED) v6
Upgrade ROM code error
Please try again
Serial
Please use "Search" function before you posting a new thread.
http://forum.xda-developers.com/showthread.php?t=502167
That doesn't seem to be the same problem as the one I'm encountering. I found that thread via Google as I said I had searched in my post and flashing the stock HTC ROM that came with my device did nothing to solve the problem; 3 machines here, one running XP, one running Vista and one running 7 all fail to connect to the device to allow for any sort of flashing and flashing via an SD card does not provoke a response either.
--Edit--
Sorry - realised that my reply sounded a little stroppy! Blame it on the stress of having a possible brick on my hands! Thanks for the attempt to help but, like it says above, that solution hasn't worked for me
dom_mitchell1 said:
That doesn't seem to be the same problem as the one I'm encountering. I found that thread via Google as I said I had searched in my post and flashing the stock HTC ROM that came with my device did nothing to solve the problem; 3 machines here, one running XP, one running Vista and one running 7 all fail to connect to the device to allow for any sort of flashing and flashing via an SD card does not provoke a response either.
--Edit--
Sorry - realised that my reply sounded a little stroppy! Blame it on the stress of having a possible brick on my hands! Thanks for the attempt to help but, like it says above, that solution hasn't worked for me
Click to expand...
Click to collapse
Have you tried reading cRaCKwHoRe's guide for flashing 1.56 roms. Can be found in my signature. If you follow his steps, you should have no problems
dom_mitchell1 said:
That doesn't seem to be the same problem as the one I'm encountering. I found that thread via Google as I said I had searched in my post and flashing the stock HTC ROM that came with my device did nothing to solve the problem; 3 machines here, one running XP, one running Vista and one running 7 all fail to connect to the device to allow for any sort of flashing and flashing via an SD card does not provoke a response either.
--Edit--
Sorry - realised that my reply sounded a little stroppy! Blame it on the stress of having a possible brick on my hands! Thanks for the attempt to help but, like it says above, that solution hasn't worked for me
Click to expand...
Click to collapse
Hi, dom_mitchell1...did you manager to fix you HD ? I have encountered the "exact" same problem...I went from 1.56 to 1.54...and now I am stuck on the bootloader at "Loading...." If you have a fix...can you please let me know...and save my HD as well....thx
If you use USPL you will be able to flash everything you want.
Fallen Spartan said:
Have you tried reading cRaCKwHoRe's guide for flashing 1.56 roms. Can be found in my signature. If you follow his steps, you should have no problems
Click to expand...
Click to collapse
That's what I was following when things went wrong. Don't know what I did but during the downgrade process the flash "encountered an error" and had to restart....only it never did and just left me stuck in the bootloader with an error message.
It's fixed up now though and I'm running Dutty's shipped version quite happily. To fix it I tried different .msi packages from HTC and eventually one of them managed a successful flash. From there I was able to continue with cRaCKwHoRe's guide.
i had a similar problem i was upgrading to 1.56 so i to my thinking reverted to a stock rom them loaded 1.14 stock spl where my phone started showing the error screen i investigated and found that the stock rom id downlosded from the stock rom section must have been tampered with as the signarure was incommplete. so now the spl was reading 114000... as it was stuck in tri screen the data had loaded to my device it justxwasnt signed so wouldnt work i dowladed the appropriat 1.56 rom from htc which includdes the new 1.54spl started it and there i whent stock 1.56 rom with stock 1.54 spl. i than loaded olinexs new hspl im running vista so had to use the manual tool but othere than that installed ok.
i hope that helped in short as long as ur screen is reading a stock spl u can install an apropriat 1.56 rom from htc i belive the issue is caused by impropper signage of some stuff marked as stock here.
I've been lurking with the XDA forum for quite sometime now and its my very first posting and I'm having difficulties finding answers on search box I just simply give up looking for appropriate answer to my question. Since I like to use the good old Winmo 6.1 rom (Davideuck_V-7_MSVC to be exact)my bad is I forgot to SPL to earlier version 1.15 so got a green kinda thing on my screen, so I apply Restore_Stock_SPL_115 and everything went fine. (I know I'm stupid ) Unfortunately after I update the Time and Date it suddenly appear " This concludes the beta test for this software release....... blah, blah,.... guess what? its a time bomb can't do anything on screen but to reset. So I decide to re-flash it again but I got stuck at 0% on bootloader mode and got Error 262, I tried to understand whats the meaning of it and I did, but never got any solution how? I tried to flash it with HSPLWrapper_Blackstone_156OliNex to restore Winmo 6.5 but I got stuck again on 0%. something unusual I tried to reflash more roms and it didn't work. All the Roms I've wont reach 1% Even flashing on SD card trick wont load. And my spl ver 1.15 can't flash anything. So I that's why I need your help desperately...
Near enough the exact same situation as me! I think that 1.15 file may have issues.
wayneroughneckz said:
I've been lurking with the XDA forum for quite sometime now and its my very first posting and I'm having difficulties finding answers on search box I just simply give up looking for appropriate answer to my question. Since I like to use the good old Winmo 6.1 rom (Davideuck_V-7_MSVC to be exact)my bad is I forgot to SPL to earlier version 1.15 so got a green kinda thing on my screen, so I apply Restore_Stock_SPL_115 and everything went fine. (I know I'm stupid ) Unfortunately after I update the Time and Date it suddenly appear " This concludes the beta test for this software release....... blah, blah,.... guess what? its a time bomb can't do anything on screen but to reset. So I decide to re-flash it again but I got stuck at 0% on bootloader mode and got Error 262, I tried to understand whats the meaning of it and I did, but never got any solution how? I tried to flash it with HSPLWrapper_Blackstone_156OliNex to restore Winmo 6.5 but I got stuck again on 0%. something unusual I tried to reflash more roms and it didn't work. All the Roms I've wont reach 1% Even flashing on SD card trick wont load. And my spl ver 1.15 can't flash anything. So I that's why I need your help desperately...
Click to expand...
Click to collapse
If you are getting an Error 262, you need to run manual sspl in order to resolve this. Read this post for the steps (post #2) and sspl tool (post #1) - http://forum.xda-developers.com/showthread.php?t=505377. You can also get all of the steps needed to successfully flash. if you have questions, please post them in that thread.
It seems when I restart my phone normally, I noticed that the message about " This concludes the beta test for this software release....... blah, blah" the manila interface was behind it when I press the task manager and the volume buttons it responses means its not bricked (hope so) maybe the reason why I cant flash anything? Or whatever...Well that's my observation..... Please guys I needed my phone badly tomorrow
Did you not read my post . You can flash another rom, error 262 is common. You just need to use sspl before flashing to hspl 1.56.
if ur stuck with hspl and cant flash that than try uspl or try stock rom.... they get installed without hspl or uspl installed.... its available in the blackstone wiki section
and with stock rom get through tomorrow . than try hspl or uspl with custom rom later on when u have free time
Upgrade the ROM with latest official HTC release it upgrades the bootloader to ver 1.54 as well. Then you can install the newest version of HSPL or just use USPL to flash whatever cooked ROM you want.
Apologies on replying again here instead of posting on the designated thread , but forgive my innocence the thread says "" launch SSPL-Manual.exe from attachment, run it, wait until 1.07.OliNex tricolour screen says "USB" on it, then run the HardSPLWrapper_Blackstone.exe on the PC. "" how exactly that's going to be done? Currently I got the tri-color screen saying SPL-1.15.0000 and a USB on the bottom and when I flash either hspl or uspl I always end up on gray screen with a 0% that doesn't move at all, how can I manually apply SSPL? I cant access Manila interface because of time bomb message? My life's getting complicated!
If possible try flashing from an XP box, Vista/7 might give you some additional trouble if you don't use the right drivers. But if you get to the 0% screen, the issue shouldn't be with the SPL... so don't worry, I doubt the phone is bricked
So: try XP and/or using the drivers provided in the Flashing-thread
zerozed said:
Upgrade the ROM with latest official HTC release it upgrades the bootloader to ver 1.54 as well. Then you can install the newest version of HSPL or just use USPL to flash whatever cooked ROM you want.
Click to expand...
Click to collapse
I tried the Official one Blackstone_WWE_1.56.405.1 and got Error[294] Invalid Vendor ID
wayneroughneckz said:
I tried the Official one Blackstone_WWE_1.56.405.1 and got Error[294] Invalid Vendor ID
Click to expand...
Click to collapse
Did you downloaded the ROM from the HTC site? If the ROM is from the official site try again using USPL.
I seach the wiki page and found the latest version which is "Blackstone_WWE_1.56.405.1" and I can't find it on the official site, it should be "WWE" not specifying on certain countries, so I manage to download it from Rapidshare link. and for the SSPL I don't think I can do that coz I can't access my phone coz it has tim bomb probably the main culprit here.
Any flashing problems should be posted in Dummies Guide thread.
Thread closed