I flashed my 8125 which i thought was a g3, but clearly as it hung at 99% of the flash It is a g4 that has been flashed with a g3rom..... now I has read about some users reflashing their phones... how do i do that since i can no longer establish an activesync connection? i power up the device... shows the color coded screen (ipl 2.24 spl 2.25) there is a USB text in the grey bottom section, but windows, and different flashing exe's don't respond to me plugging/unplugging the device. Please help
8125 help
whats the trick to get into the bootloader? i've tried reseting, and pressing the camera button a dozens times now, now help
I think you have to hold both the voice messaging button as well as the camera button to get into the bootloader.
In your first post you were already in the bootloader -- "color coded screen" as you put it. First thing. Take the battery out before you discharge it too much to continue. It cannot charge in the state you are in and will discharge very quickly until useless.
[email protected] said:
I flashed my 8125 which i thought was a g3, but clearly as it hung at 99% of the flash It is a g4 that has been flashed with a g3rom..... now I has read about some users reflashing their phones... how do i do that since i can no longer establish an activesync connection? i power up the device... shows the color coded screen (ipl 2.24 spl 2.25) there is a USB text in the grey bottom section, but windows, and different flashing exe's don't respond to me plugging/unplugging the device. Please help
Click to expand...
Click to collapse
if you see the USB in the corner of your bootloader screen you should be able to flash a G4 compatible rom back into your phone from there.
Just boot the phone so that you can see that screen and then start the install process on your computer. You will need a ROM that doesn't include the bootloader. So make sure it is a G4 compatible ROM.
I by no means am an expert but I was recently in a similar situation with my G3 (flashed a 2.xx rom that didn't include a bootloader with a 1.xx bootloader)
and this is what I had to do because I couldn't connect to Activesync, or communicate with Windows in any way with that messed up flash.
I'd try flashing the latest stock 8125 ROM from here: http://www.htcamerica.net/support/docs/RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship.exe
ahhhhh yeah
okay... i was confused about just what the bootloader was... and i was in the bootloader... thanks for the help several attempts at detecting the device didn't work... i tried with summiters Cingular_Custom_AKU2.3_Combo_Installer_V1.exe and it finally detected it... which i guess means i have a g3... anyway all is working now, thanks for the help
Hi, I also had problems with USB after 3.2 rom update. I always get a USB not recognized and I can't flash with any exe ROM. Even in bootloader it was not recognized. Did you have the same problems with the phone?
Hi guys, i've been around sometime in the "qtek" world and had owned some of them in the past, now i own a wizard and i expect to begin mastering the thingie..
The problem is that after some experiments i have this problem :
I think it is not bricked.. it boots the OS but it is so sloowww with stops everywhere, takes like 4times the time to open "settings" than before. and it does not turn the charge light on and is not recognized by usb port so it does not sync and i'm unable to re flash it..
What i did was to downgrade it with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
and then i stick the AKU3.2-1.0RC1
It has been cid unlocked by me yesterday and was working fine with another rom..
I was thinking of entering bootloader manually and then somehow flash it..
Please Help
thanks !
i'm glad i solved the problem.. just entered manually in bootloader then flashed a original qtek rom and it fine now
thanks anyway, hope this help other people in this very situation
bye
cheers from portugal
W4R_M4ST3R said:
Hi guys, i've been around sometime in the "qtek" world and had owned some of them in the past, now i own a wizard and i expect to begin mastering the thingie..
The problem is that after some experiments i have this problem :
I think it is not bricked.. it boots the OS but it is so sloowww with stops everywhere, takes like 4times the time to open "settings" than before. and it does not turn the charge light on and is not recognized by usb port so it does not sync and i'm unable to re flash it..
What i did was to downgrade it with CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
and then i stick the AKU3.2-1.0RC1
It has been cid unlocked by me yesterday and was working fine with another rom..
I was thinking of entering bootloader manually and then somehow flash it..
Please Help
thanks !
Click to expand...
Click to collapse
You can't go from 1 to 3. Re-flashing a stock ROM was a good move.
--M
Hi W4R_M4ST3R!!!
I think i have exactly the same problem as you had!
I have installed new ROM, and my T-mobile MDA Vario working veeeery slow, and i could not connect it to my computer!!!!!!
Tell me please (in details) what did you do with your phone.
Thanks!
zorrozorro said:
Hi W4R_M4ST3R!!!
I think i have exactly the same problem as you had!
I have installed new ROM, and my T-mobile MDA Vario working veeeery slow, and i could not connect it to my computer!!!!!!
Tell me please (in details) what did you do with your phone.
Thanks!
Click to expand...
Click to collapse
This topic has been discussed in length all over the forum. But, here we go again. This will be based on you having a G3 device.
1. Make sure that your device is CID unlocked. if not follow the sticky thread at the top of this forum. and read through all of it BEFORE you begin
2. make sure that you have ipl/spl 2.x
3. Now upgrade to any rom you want.
_Nomad_ said:
This topic has been discussed in length all over the forum. But, here we go again. This will be based on you having a G3 device.
1. Make sure that your device is CID unlocked. if not follow the sticky thread at the top of this forum. and read through all of it BEFORE you begin
2. make sure that you have ipl/spl 2.x
3. Now upgrade to any rom you want.
Click to expand...
Click to collapse
How can i upgrade my ROM if i could not connect my phone to the computer! The main problem is that i could not syncronise my phone and my PC.
enter bootloader mode... press the two buttons (camera & voice command) while resetting the device. you should get a screen that's red, green and blue. from there you can reflash your device. if that doesn't work, your phone is bricked
_Nomad_ said:
enter bootloader mode... press the two buttons (camera & voice command) while resetting the device. you should get a screen that's red, green and blue. from there you can reflash your device. if that doesn't work, your phone is bricked
Click to expand...
Click to collapse
Thank you!!
Could you explane me a bit more precise what does it mean bootloader and reflash? Does it mean that i can syncronise phone and computer when i have RGB on my screen?
When you've got your device in bootloader mode just plug it in and start the upgrading procedure
_Nomad_, thank you!
It works now!!
zorrozorro said:
It works now!!
Click to expand...
Click to collapse
Like music to my ears
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Adding additional info
My phone is a G3, CID and SIM are unlocked, desktop is using Windows XP, SP2 and ActiveSync is Ver. 4.5.0
phone isnt bricked, your getting into bootloader fine. you need to turn it on, get it into bootloader i mean. if needbe press camera and soft reset (power button) then plug it in USB. You then need to flash your phone with the operator ROM, or the ROM you want to flash it with. Your phone is by far bricked, G3 ones are really difficult to ruin. I learnt that first hand
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
jphuffs said:
At 56%, the desktop went to a blue screen and said an error had occurred and the system must be restarted. The screen asked if I had installed any new programs, check with the adminstrator, etc. The only program recently installed is the program for this ROM revision. When it crashed, the phone had a completion bar in the top 1/3rd, showing 56% completion. The rest of the screen was white. I restarted the desktop and was unable to establish a sync connection. I then preformed a hard reset on the phone. When it restarted, it showed 4 color bars, red on top, green, blue and white at the bottom. Since I cannot restablish a sync connection, how do I finish the modification. I am now concerned that I have "bricked" the phone. I am reluctant to try this mod on another phone until I can determine what went wrong.
Click to expand...
Click to collapse
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
akashastrega said:
http://forum.xda-developers.com/showthread.php?p=1560272#post1560272
Think I may have done just that...bricked my phone. G3 wiza200, IPL/SPL 2.26
Cannot get it to read a usb connection at all. Help please?? Thanks in advance
Click to expand...
Click to collapse
hi
i have read ur situation at thread u have mentioned here,well i can assure u it's not bricked,cuz as sometimes it's able to go to bootloader mode.
The only problem to me seems the usb connectivety problem.
does it charge ?,if not then clearly it' a usb connectivity,if u can manage to get another usb cable and check out,hope it wud clear this doubt
zabardast_1 said:
hi
ur phone is certainly not bricked,cuz ur desktop crashed therefore the phone upgrade cudn't be completed,nothing to worry as long u can get to bootloader mode(Tricolor Screen)
Ok,listen, u do not require active sync connection,to flash a rom,do as I say and it'll be working fine,follow these steps to complete ur upgrade:-
1.Switch on,go to bootloader mode (Tri colored screen).
2.Connect usb cable to the phone and PC
3. After connecting usb cable,u will notice small 'usb' showing on the corner at the bottom of the bootloader screen of ur phone,if it shows,ur r ready to flash and upgrade
4.start the upgrade RUU_ rom u want the to upgrade with
5. complete the flash,let it reboot
let me tell u,u dont need active sync connection to upgrade
cheers
Click to expand...
Click to collapse
I just had this happen to me as well, I got stuck a 29%
Now when I get to bootloader it shows the IPL 2.26 and SPL 2.26 and also a RUU in the top right hand corner. Plug in USB and I get USB at the bottom left but then when I try to launch the RUU with the rom I want to flash I Invalid update tool, download new tool... It wont "Verify information on the device"
**EDIT
Nevermind, I just got Titanium to take... I may be ok... I think the RUU in the vanilla download I got is messed up or something...
Currently ripping through the rom update now. Damn I just got this phone yesterday I was gonna be pissed if I killed it.
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
ok when u swith on the phone what happens ?
does it go to bootloader mood ? or u force it to go bootloader by keeping camera button pressed and doing soft reset ?
well,after geting to bootloader mode,don't reset again just establish usb connectivity and when it show usb in the lower part of the bootloader screen launch ruu and start the flash.if it still stops with an error,post that error,then it means u had a bad flash or no flash at all.are you pretty sure you got it CID unlocked ?
tell you what you do,go to this link download WST tool and apply it,than post the data info it gives here,this will give the present status of your phone,ok
http://forum.xda-developers.com/showthread.php?t=329170
read this sticky:http://forum.xda-developers.com/showthread.php?t=298613
jphuffs said:
Okay, I have the tricolor screen with IPL 2.25 on the left top of the red bar, SPL 2.25 on the left bottom of the red bar, RUU on the right top of the red bar and USB on the bottom left of the screen.
I push the camers button, do a soft reset and launch the ROM update. First window says "Verifying information on your PDA phone. Please wait." After a few moments I get a window that says "ERROR (300) This update utility cannot be used for your phone. Please get newer update utility."
If I try again, I get a window with "ERROR (264) CONNECTION" And an additional message about the USB connection not working. I am using a USB charge/sync cable and not a cradle.
What now?
Click to expand...
Click to collapse
download the wizar-love rom
flash it using the ruu provided..
ftp://xda:[email protected]_Novii+CF2.rar
it should work.....
read this sticky
http://forum.xda-developers.com/showthread.php?t=298613
G4.1 Does you're device start normally (yes) or is it stuck on the three-colored bootloader screen (no)? YES... go to step G4.4, NO go to step G4.2
G4.2 Turn off you're device totaly. Remove the SD card and disconnect the USB cable from you're device. Turn on the device while holding the camera button. You will get into bootloader mode (3 colored screen). Connect the USB cable to the computer and you will see USB at the bottom of your screen above the left softkey (Activesync will not connect in bootloader mode, but you can flash from this screen!). go to G4.3
G4.3 Download wizard_love rom and flash it to your device. Your device should startup again after doing this. Go to G4.4.
G4.4 Is your device CID-unlocked (note: it's not the same as SIM-unlocked!)? YES... go to step G4.7, NO OR DON'T KNOW go to step G4.5. (note: CID-unlocking a G4 is only possible by paying for it at imei-check!)
G4.5 Download enable-rapi.zip. Transfer Cert_SPCS.cab and EnableRapi.cab to your phone. Run Cert_SPCS.cab FIRST and EnableRapi.cab SECOND. Turn your device off and on or wait 5 minutes before soft resetting. Done? Go to G4.6.
G4.6 Follow this great thread by the-equinoxe: [solution] G4 SoftSPL Flash any ROM to CID locked G4 [UPDATED] and load the softSPL on your device using his method. Make sure you take a G4 safe rom (see the thread for details). After the steps you'll have the rom of your choise on your device!
G4.7 You're reade to flash the AKU2, AKU3, WM6 rom of you're choise IF the rom DOESN'T contain IPL/SPL. AKU3 and WM6 roms normally don't contain IPL/SPL. If you want to flash an AKU2 rom, make sure you take the G4 version. If you get an error 300 (invalid update tool) while trying to flash your device look at this thread!
NOTE: If you tried to flash a G3 rom with IPL/SPL in the rom on a G4 you probably will have a bricked device! DON'T flash the new 3.08 and 3.09 IPL/SPL to your G4!
NOTE2: If you got problems flashing with softSPL: Follow this great thread by mun_rus: Solutuion found: how to flash any rom to CIDLOCKED DEVICE. If your device won't start after flashing you can use step G4.2 and G4.3 and try again. Also look at this thread by eddieitman: Faria G4 Step by step installer with instructions to make sure you did all the necessary steps!
Crashed during flash
It has been suggested that I download Wizard Service Tool. OK, I did that. The Wizard Service Tool says to connect to ActiveSync. Can't do that. Phone is locked in Bootloader. It boots up into Bootloader. Any action requiring ActiveSync won't work as long as the phone is locked in Bootloader. Any suggestions as to procedures at this point. Remember, that trying to flash the ROM at this point, I get a message 300 that says I need to get a newer update utility.
Crashed during update
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
jphuffs said:
It has been suggested that I flash with wizar-love rom. Did that. Got a message 300, my phone need a newer update utility.
Click to expand...
Click to collapse
go to the G4 section and look for the HardSPL thread. Once there get the MUNRUU file from first post and use it with the ROM you wish to flash as it might do the trick of the ERROR 300
crashed during flash
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796
jphuffs said:
It was suggested that I go to G4, first thread, HardSpl and down load file, munruu. Didn't find any such file. Went to second thread, by mun_rus, but was unable to download file.
My 8125 is locked in bootloader and I don' know what to do.
I still need help!!
Click to expand...
Click to collapse
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
(mestrini;1565518]this is the thread. and the link is there......
http://forum.xda-developers.com/showthread.php?t=332320
or another thread with link...
http://forum.xda-developers.com/showthread.php?t=334796)
My phone is a G3. These links are pretty adamant about being for G4 only
jphuffs said:
My phone is a G3. These links are pretty adamant about being for G4 only
Click to expand...
Click to collapse
I'm talking about the, so called, 'MUN RUU' which are the files used to upload the nk.nbf. You just have to replace those for the ones you're using now; NOT THE nk.nbf, just the others...
zabardast_1 said:
download latest Official Rom from carrier official site, establish usb connection while in bootloader flash,it will start working,after that follow the procedure of unlocking and upgrade
or if you have put in Sdcard,remove it and then switch on the device,it might get ok.It's seen in many cases that some Sdcards create problem while upgrade and bootloader screen gets stuck,by removing it,it starts to work fine
good luck
Click to expand...
Click to collapse
What is "Official Rom from carrier official site"?
The SIM card was removed.
Hope this helps
jphuffs said:
What is "Official Rom from carrier official site"?
The SIM card was removed.
Click to expand...
Click to collapse
For instance, if you are (like me) with TmobileUS, go to the Tmo site and go to the page that gives you the download to rom 2.26. I have that rom, if you are with Tmo, but won't be able to upload it until later...
http://tmobile.infospace.com/tmweb/...wnloadCenter/DeviceDownloads.aspx?deviceID=24
THAT^^^ is for TMOUSA...it is the official Tmo rom. If you are with cingular/att, you need to access their website and download their official rom, etc.
After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???
kevinalmere said:
After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???
Click to expand...
Click to collapse
Always post the data of your your phone,to get help.
secondly you had a bad flash,perhaps your phone is CID locked. Which rom were you trying to flash ?
Now to recover,download the official carrier's rom and flash it while in bootloaders.The phone will start working again in default status,then,Read and understand the unlocking method and the flashing guide,read the stickies carefully and perform the method correctly.
cheers !
i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....
Help!!!
I have same Problem with TNE-V1.0n_4mb.exe
IPL 3.08
SPL 3.08
kevinalmere said:
i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....
Click to expand...
Click to collapse
If you can go to boot loader, most likely you will be ok. When you plug in the usb port, does the words in the screen change from serial to USB? Once it changes, then flash your official, and then CID unlock your device (this is different from SIM unlock). Then flash to the ROM you want!!
PS: Go read wiki about how to unlock and flash and understand more about your device. http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?
kevinalmere said:
The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?
Click to expand...
Click to collapse
Vista dont like upgrading and stuff...but there is a work around, search the forum and see if you find it. Or try using XP.
okee problem solved working again
thanks for your help!!!
kevinalmere...
How did you resolve the issue I'm having very simular problems and believe it's my Vista OS causing the problem..
Orange SPV M600 G4
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 4.0.0.0
Sorry should explain my issue incase anyone can help.
I attempted an upgrade to WM6 using an Upgrade .Bat from this site. I was slightly impatiant due to not being able to complete the downgrade first anyway the upgrade frose, after a while I canceled the update and carried out a hard re-set... Since then I'm not able to boot nor connect to my desktop via Active sync (WMDC (Vista))
I've followed every instruction I can find but only to be meet with RUU Errors saying can't connect or file open. I can however acces my Bootloader screen and when connection is made the USB symbol shows on the screen of my phone...
Any help would be greatly recieved......
i got a wiza200 G3 IPL/SPL 1.0.6 that is locked to T-Mobile, now the problems are:
1) that i cannot access the Bootloader, i hold down the keys but it just resets and no bootloader comes on.
2) tried hard resetting it, the procedure goes just fine, but does not reset.
3) In addition to my problem the phone has a password set at the boot of windows but i do not know the password
4) when i connect the usb nothing happens(i tried all the possible solutions for this one but i think my usb slot is broken)
5) its SIM/CID locked
6) theres no way of fixing this isnt it?i have searched the whole forum for a possible CID unlock through an SD Card
but as I can see noone has found a solution about that yet..and probably never will..
Update: I managed to hard reset it and it gets in Windows now but the usb still does not work, I have established a connection with ActiveSync through Bluetooth and im trying to use WST and i do 'Enab RAPI + Unsigned Apps' and get good results:
Uploading files...
Running Cert_SPCS.cab to change Unsigned
Prompt policy...
Running EnableRAPI.cab to remove restrictions
on RAPI communications...
All Done!
You can fully use this service tool now.
Repeat procedure only after a hard-reset.
Click to expand...
Click to collapse
but the problem is when i try to CID Unlock i get this error:
Warning!
A device was detected but one (or both) of RAPI
Communications and Applications Policy isn't
enabled.
Use first button for that purpose and try again
Click to expand...
Click to collapse
Update 2
I Fixed this by manually put EnableRapi in the windows folder of the device and running it.
I used Lokiwiz and tried to CID/SIM Unlock it, but im not sure if it worked, after each step the device rebooted just
like it said in the 'readme' file, now is there any chance to put custom ROM to the device through bluetooth?
any help is much appreciated, thanks in advance
also i have another HTC wizard with custom WM6 if that helps..but its G4
Okay, first of all, your post is somewhat confusing, but it appears you are trying to get a custom rom onto your G3, right?
You already hard reset your phone, so now to deal with the bootloader problem...
1. turn your phone off, and remove the battery just to be sure.
2. hold the camera button on your phone.
3. insert USB cable into the phone.
Now your phone should be in the bootloader mode, and you are ready to start the flashing process!
Flash to the most recent Official ROM. Then follow whatever tutorial you found to flash your phone.
Oh, and I am not sure, but I do not think you should use the bluetoth connection to do the lokiwiz stuff. Use the USB cable. Also, I would suggest you find and learn to use the Wizard Service Tool. It does more, and I think the GUI might be just right for you.
thanks for the reply, but the problem is that my usb port is damaged and i cant get it to work. i managed to unlock cid/sim through lokiwiz using bluetooth, i tried flashing the rom with bluetooth but it wouldnt work and that is normal because when you use a custom ROM installer the installer makes the device go to the RPG mode and there it loses the bluetooth connectivity, is there any other way to install the ROM?maybe with SD Card or something? I have the searched the forums but cant find a solution that actually works
I did a search myslef, and all I came up with was this: http://forum.xda-developers.com/showthread.php?t=366894
My only problem is this: I have never been able to sync a phone through bluetooth without first making a USB connection.
I do not want to upset you, I just want to make sure you don't give up on a possibly working phone.
i can make a connection using bluetooth and unlocked my sim/cid, now i just need a solution to flash the rom without the usb
then you will have to find someone with a G3 that is willing to do what is described in the link I posted above.
can anyone from here help me make this backup sd card?