Windows Rom on SD Card - 8125, K-JAM, P4300, MDA Vario Software Upgrading

Does anybody hav a rom image that i could save to my SDcard since i cant connect the mda to my active sync

mikethegreat45 said:
Does anybody hav a rom image that i could save to my SDcard since i cant connect the mda to my active sync
Click to expand...
Click to collapse
If you haven't already, you can try putting the mda into bootloader mode directly. That way you don't need to use activesync. Then reflash your mda with a known working rom. Disconnect your mda from the usb, then do a ctrl-alt-delete, to pull up the windows task manager. Go to the processes tab, and select the wcescomm.exe process and then end the process. Now, put your mda in bootloader mode by pressing the camera button in and resetting with the pin hole. After a few moments, the bootloader (colors) screen will come on, and you can let go of the camera button. Now plug in the usb to your computer, and you should be able to flash your rom.
Good luck!,

sorry i tried that, unfortunately that didn't work either, is there any other way to update, im still on the factory rom it came with.

Related

Battery Problem after upgrading with new uk t-mobile rom

Hi,
i upgraded my charmer with the new uk t-mobile rom and my nproblem is that the battery does not charge,and i don't know how to do
have you some suggestions???
Waiting your answer,thanks a lot,Antonio
Hi did you get a answer
Hi I have the ssame problem, did anybody come up with any ideas ?
Cheers
TBW
Battery Problem
Hi, I have too this problem with wm6 rom have you some suggestions??? pleas
Hi...nobody can help us???
Try plugging in the charger and when its plugged in, hit soft reset button with your stylus. Wait for the system to boot and see if it charges.
vlodeck said:
Try plugging in the charger and when its plugged in, hit soft reset button with your stylus. Wait for the system to boot and see if it charges.
Click to expand...
Click to collapse
i have the same problem and doesn«t work for me
Then my guess is you flashed a ROM not intended for your device.
now how i can solve this?
Reflash a charmer rom? And if that doesn't work, try a prophet WM5 rom.
it says that i don't have enough battery, is lower than 50%
Use the NO_ID RUU version instead.
i already try a few roms and i can't flash the pda with none of them
You will need to reboot in BootLoader mode first (powerkey+camera+reset).
hello!
a downgrade my Charmer and now the battrery is 0%, when i connect to usb phone don't want to start, on charger it startet but battery dont want to charge. help pls ...
Hi,
I have solve this problem but I'm not sure how I've done this.
1. dowlnoad cab from this link http://forum.xda-developers.com/showthread.php?t=327988
2. I have use program Wizard Service Tool and clear everything what is possible including format.
3. reset
4. format after strart camera+record+soft reset
5. after reset bootloader mode, and first time my phone has connet in BLmode with USB.
6. Then I have run original T-mobile RUU and it's working
My battery has been on 0% in system as well but after downgrade battery states about 70%
have a same problem.
did anybody else solve this problem? anybody used SD flashing method?
i've solved problem partly - now battery charges, but i can't start it without power supply. so what have i done:
1) i've downloaded ShellTool_bugfixed.zip (you can easily find it google).
2) unpack it.
3) copy Cert_SPCS.cab and EnableRapi.cab to you WM and install
4) extract nk.nbf from original Charmer ROM into ShellTool folder
5) start ShellTool.
6) press Get ROM Info
7) press Extract OS
10) press Flash OS
11) press ОК
Followed all this steps, now i've got an original charmer os, but bootloader is still from previous crap ROM. so there is trouble with starting it up. If you phone doesn't start even when you charging it from power socket, so try to wet contacts on battery - it should work.
now i thinking how to re-flash bootloader, cuz it cannot enter into bootloader witout power supply from socket. It's no possible to flash it from PC, cuz it cannot enter a booloader plugged into USB port. It seem that there is not enough power impulse to startup.

SD-Card Rom for Charmer

Hi guys,
I have a big problem with my charmer.
At the begining I tried to work with my charmer and it was OK, but after a short time it resets from alone. It was the same situation everytime, when the charmer was starting and I did the calibration of the touch screen it was reseting always as soon as I pressed the cross on the right bottom.
Next step was to flash the ROM - it was sucessful, but the same situation
-> Reseting at the calibration.
I did once again a flash but it resetet during flashing and now I have the situation, that I can enter boot loader but as soon as I connect it resets.
Battery I checked -> It is OK.
So does anybody have a Rom on SD card ? -> I have no other joice, this is my last chance to get it running again.
Thanks for your help in advance
Best regards
Helldriver
Hi
1. Kill (task manager) wescomm.exe (this is related with activesync installed on your PC).
2. Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
3. Now connect your USB cable to your phone
4. Download T-Mobile compactii_aku2.0_05-2006 rom and Flash it works for me
jerry
Not working with USB
Thanks for your comment, but it is not working, due to the fact that the MDA tripps as soon as I connect the USB cable (even if I kill the wecomm.exe).
Therefore my only chace is the SD-card
So if anybody has a ROM on SD card, please help me getting my Charmer running again.
Regards
Helldriver
Hi Gents
is there somebody who can help me ?
I really need a SD-card rom
Thanks
Helldriver
Sorry ,but I am noob. How can i flash it??? And how can i kill wescomm.exe???
Rom backup
Hi all,
Still searching for the SD ROm image... Can someone upload?
Please...

Big Problems!!! System is freezing all the time!

Hello,
now the time is come that I really need your help.
Everytime when I try to turn on my MDA Vario 3 the system is crashing after the Bootscreen. I could do nothing exept turn of the device.... I already tryed it with a lot of hard and soft resets but it still wont work.
When the PPC is connected to my PC its going to freeze in the main menu from Active Sync (I dont know why this pops up even before I could enter the PIN code)
and when the device isn't connected to the PC the system is going to freeze in the HTC Home screen (at the point before you enter the Pin code normaly).
I also couldn't flash the rom because even wehen Active Sync pops up the device could not connect to the PC...
So when somebody have an Idea which coul help me, just let me know!
PS: Sorry for the bad english
DerGregen said:
Hello,
now the time is come that I really need your help.
Everytime when I try to turn on my MDA Vario 3 the system is crashing after the Bootscreen. I could do nothing exept turn of the device.... I already tryed it with a lot of hard and soft resets but it still wont work.
When the PPC is connected to my PC its going to freeze in the main menu from Active Sync (I dont know why this pops up even before I could enter the PIN code)
and when the device isn't connected to the PC the system is going to freeze in the HTC Home screen (at the point before you enter the Pin code normaly).
I also couldn't flash the rom because even wehen Active Sync pops up the device could not connect to the PC...
So when somebody have an Idea which coul help me, just let me know!
PS: Sorry for the bad english
Click to expand...
Click to collapse
Flash from bootloader. Make sure you're hard SPL though, or that it's a compatible ROM for your CID.
have you tried:
Start->Settings->Connections->Usb to PC and clear the 'Enable advanced network functionality' checkbox ?
manuv1615 said:
have you tried:
Start->Settings->Connections->Usb to PC and clear the 'Enable advanced network functionality' checkbox ?
Click to expand...
Click to collapse
Hello,
I could not try this option because I couldn't do anything exept restart/turn off the device.....
Now I found out that I can flash the Rom with the bootloader but the problems still where the there with every rom... And I tryed a lot...
After the 3. or 4. restart with the new rom the problem pops up again....
DerGregen said:
Hello,
I could not try this option because I couldn't do anything exept restart/turn off the device.....
Now I found out that I can flash the Rom with the bootloader but the problems still where the there with every rom... And I tryed a lot...
After the 3. or 4. restart with the new rom the problem pops up again....
Click to expand...
Click to collapse
You said that you could enter bootloader menu right?
now tell me, whats written there?
i'll wait here,.
Theres a 4 colour screen (red, green, blue and white)
And in the red bar is a text with a yellow font:
KAIS139 MFG
SPL-1.0.0liPof
CPLD-8
And below in the withe bar stands "Serial" or "USB.
What rom did you use?
try HardSPL 3.56 by jockyW,.
then reflash your ROM,.

How to install a rom please help

I am trying to install a rom to my wing from over 3 days couldn't do it , I need to know where to put the files and how to set the files up , This maybe easy for you but not for average person like me , Please help.
reply
sorry i dont have a answer for you.but, i feel your pain i am going through this same stuff and i is pissing me off. i had my friend do everything but he is getting pissed off now because i keep calling him on ****. i need help too.
Well, we need to know what you are doing first!
What ROM are you flashing?
Do you have HardSPL already on? Or do you have no idea? haha
Thanks for your respond , I will like to install ROM HERALD WWE 6.1 BUILD 20764.1.4.3 (Blue clear) , I have no idea what is HardSL !! but i will learn if you give me a little direction .
tazzam72 said:
Thanks for your respond , I will like to install ROM HERALD WWE 6.1 BUILD 20764.1.4.3 (Blue clear) , I have no idea what is HardSL !! but i will learn if you give me a little direction .
Click to expand...
Click to collapse
How to Flash HardSPL
1) Find out your IPL
-- Do a Soft Reset (Push Button under volume w/Stylus)
-- While doing Reset, hold the Camera button, it should bring up the Bootloader menu and list your IPL (I think, it has been a while since I haven't been running HardSPL)
2) Verify your IPL is 4.xxx or Higher!
3) Boot your phone Again
4) BEFORE Hard-SPL--go to Settings->Connections->USB to PC and check that checkbox
5) Download HardSPL:
http://rapidshare.de/files/38148213/HardSpl_WM6.rar.html
6) Transfer these files to the phone:
--- a) install canonyang.cab
--- b) install aserpolicy.cab
--- c) install disablesecurity.cab
7) Soft Reset again
8) Run ROMUpdateUtility.exe
9) screen will become white - WAIT until it reboots itself (Should be like 10-15 min)
10) Phone will boot back to your main ROM
11) Soft Reset, Hold Camera button, check if SPL is 4.70.yang
Okay, now HardSPL is on
12) Download Your ROM
There are 2 ways of doing this now, either
1) Run ROMUpdateUtility.exe - When finished, go to Step 8.
-OR-
2) Put RUU_signed.nbh on your SD-Card and call it HERAIMG.nbh
3) Soft Reset, hold the Camera button
4) It will say: PRESS KEY TO INSTALL or something like that...
5) Press the volume button down or up
6) The ROM should begin to Extract/Install
7) When it finishes, do a Soft Reset
8) You should have your new ROM now!
Good Luck!
Original HardSPL Thread:
http://forum.xda-developers.com/showthread.php?t=358225
Thanks will try now
I followed the instructions, however when I turn on the phone holding down the camera button I get a white screen that states searching for SD Card (the white screen disappears quickly) then a new screen with RED, Green, Blue, White stripes with the IPL & SPL INFO, there is no option to press up to install the ROM. The ROM is in the Root of the Storage card named written as such in your walk through.
Tom in AZ said:
I followed the instructions, however when I turn on the phone holding down the camera button I get a white screen that states searching for SD Card (the white screen disappears quickly) then a new screen with RED, Green, Blue, White stripes with the IPL & SPL INFO, there is no option to press up to install the ROM. The ROM is in the Root of the Storage card named written as such in your walk through.
Click to expand...
Click to collapse
What size Card are you using?
I cannot get my 4GB or 8GB Card to flash... I have to use a 2GB card (I think it is SDHC Drivers not loading in BootLoader)
That is most likely your problem.
Try to get a hold of a smaller one (Maybe borrow one)
Fenopy said:
What size Card are you using?
I cannot get my 4GB or 8GB Card to flash... I have to use a 2GB card (I think it is SDHC Drivers not loading in BootLoader)
That is most likely your problem.
Try to get a hold of a smaller one (Maybe borrow one)
Click to expand...
Click to collapse
I had a 4gb in there, so that might be part of the problem, as time went on there was more going on it seemed. I finally got it to go back to that flash that came with the HardSPL software.
In order to do it, I started off by taking your advice. First I put in an older Lexar 2gb chip into the phone (Non-SDHC), then re-installed the three cabs that come with the hardSPL (installing them to the device, not the SD card). Then had to put the phone into the mode with the 4 different color bars (press and release the soft reset button while holding down the camera button till the bars showed), and finally I started the RUU from the PC since it still did not see or take the NBH file off of the root directory of the 2gb Micro SD.
I hope it does not get flippy like that again. The darn phone was deleting its own files as it was unhappy on the last build. Thanks for the tip on the SD swap. I'll be sure to keep that in my bag of tricks should it happen again.
Tom
where do i transfer the files to on the phone how do i install them
hankf said:
where do i transfer the files to on the phone how do i install them
Click to expand...
Click to collapse
HERAIMG.nbh go on the Root of the SD-Card.
All instructions are right in this thread:
http://forum.xda-developers.com/showpost.php?p=3321535&postcount=5
these files go to the root of the sd card: Transfer these files to the phone:
--- a) install canonyang.cab
--- b) install aserpolicy.cab
--- c) install disablesecurity.cab
Thanks for the help super n00b have been reading but still lost dont want to mess my phone up once I hard sl my phone can I still run my old rom or do I need to install a new rom right away
mmmm...
Damn Phone...
hankf said:
these files go to the root of the sd card: Transfer these files to the phone:
--- a) install canonyang.cab
--- b) install aserpolicy.cab
--- c) install disablesecurity.cab
Thanks for the help super n00b have been reading but still lost dont want to mess my phone up once I hard sl my phone can I still run my old rom or do I need to install a new rom right away
Click to expand...
Click to collapse
Those CABs can go anywhere. You need to put them somewhere (root of the SD works for simplicity)
So put the CABs on the root of the SD Card
Use File Explorer or Total Commander (Whichever you have on the phone) to navigate to your SD Card and run the 3 CAB files (Order does not matter) - Install them to the phone (Not the SD Card)
Then run the Installer from your PC as stated in the instructions.
*Note: Installing HardSPL will also install a New ROM (It is some old version of PDAViet I think)
As for installing your old ROM again, you would use a different method.
Similar to installing HardSPL, there is a PC-Based installer for the stock ROM, this ROM will revert you to T-Mobile default OS and back to SoftSPL.
I can upload this ROM later when I get home if you would like...
I think i got the CAB part understood.
When I do the HARDSPL I should have a ROM ready to install correct may I ask what you reccommend I have never used any of them so all new to me.
Could you please upload the stock rom to revert back to t-mobile, the installer and softSPL or what ever I need.
hankf said:
I think i got the CAB part understood.
When I do the HARDSPL I should have a ROM ready to install correct may I ask what you reccommend I have never used any of them so all new to me.
Could you please upload the stock rom to revert back to t-mobile, the installer and softSPL or what ever I need.
Click to expand...
Click to collapse
I would have the ROM you want ready, otherwise you would be stuck with the HardSPL ROM (Which you probably don't want to use)
I would suggest Just2Clean.
It is customizable & fast. (Can be found in the ROM Dev forum)
Stock ROM:
http://www.mediafire.com/?2nq9iu0a2nt
so with the stock rom I can go back to my t-mobile theme at any time or do I need to get rid of the HARDSLP first?
1 more question my phone is Windows Mobile 6 Pro so do I need to stick with wm6 rom or can I do like wm6.1
hankf said:
so with the stock rom I can go back to my t-mobile theme at any time or do I need to get rid of the HARDSLP first?
1 more question my phone is Windows Mobile 6 Pro so do I need to stick with wm6 rom or can I do like wm6.1
Click to expand...
Click to collapse
The Stock ROM installer puts SoftSPL back on the phone.
Windows Mobile 6.1 is just modified version of Windows Mobile 6.
It doesn't matter.
got the phone HARDSLP tried installing rom just2clean of the sd card having the same problems as in post #7 tried different size microchip 2gig with no luck so i installed touchFLO 2d and now my phone just keeps rebooting tried connect back to the pc but it sees no phone any ideas
hankf said:
got the phone HARDSLP tried installing rom just2clean of the sd card having the same problems as in post #7 tried different size microchip 2gig with no luck so i installed touchFLO 2d and now my phone just keeps rebooting tried connect back to the pc but it sees no phone any ideas
Click to expand...
Click to collapse
Try using Flash Center (http://rapidshare.com/files/202330180/Flash_Center.rar.html)
1) Put the phone in BootLoader (Make sure it says SPL 4.70.yang)
-- To get in BootLoader: Do a Soft Reset while holding down the Camera Button
2) Put the ROM in the 'RUU' folder (Name it anything [No spaces/special characters]) and try flashing using ROMUpdateUtility
If SPL is not 4.70.yang:
Try Re-Flashing HardSPL
If it won't stay connected long enough to flash (Gives an error upon flashing)
- When the Phone reboots itself, try holding the Camera button again, it sometimes will keep going
If you STILL can't get it going..
- Search desperately for a different SD Card (Make sure it is formatted in FAT32/FAT16)

Reboots when Usb connected

Flashed today my GT-I9000 to TO froyo I897UCJI6. I know i should not have done that now. But i really got pissed today at the gps of my phone and when i saw and update for galaxy s i just went for it, haven't checked the phone variant version. Thing is now my phone has no gps whatsoever it boots up fine but, sound only shows when i plug my headphones, accelerometer dont work correctly and so on....
So i though i`ll flash it back to stock. But the thing is once i connect the usb cable the phone just reboots and stays dead until the usb is disconnected.
I read the other threads but found no similar issues.
Here is a brief video of my problem
-http-://-www-.youtube.-com/-watch?v=MtcCvfCbAFk-
Remove all "-"
since i can`t post links
Anyone has any ideas how to get me back to stock?
Thanks!!
Damn i can`t even charge it!
Kinda weird indeed, try to remove the battery, wait a little, insert the battery and go to download mode (volume - / home / power) then start odin, put all files needed, and connect the usb, if it doesnt reboot hit start...
you got to enable adb debugging on your phone then open a command window and type: adb reboot download connect the usb to the phone and hit the enter key for the adb command before your phone fall asleep, then you are in download mode an can flash any rom with odin.
hope this helps, i flashed the same wrong firmware from the Vibrant.
Thanks Franklin, i tried the battery trick to no luck.
This is i cannot put my phone back to download mode because my "HOME" button is not mapped to do anything, seems like the "RETURN ARROW" button does the fuction when the system is loaded.
Any other ways to flash it back? Sd card or something?
Thanks for replies ;]
please try it my way it worked for me and i think it will work for you
I open the cmd navigate to c:\androidsdk\tools\ type in adb reboot download hit enter, it mounts daemon tools i plug in usb cable and 3 seconds later the phone goes blank and it stays unresponsive(no 3 key combination, not even the power button can turn it back on) i unplug the usb cable and the phone automaticaly shows the AT&T logo and starts up. The same happens when i plug my charger in!. Does that mean my SGS usb port is fried or something? Is there another way to flash my pnoe back to stock ROM?
I am so sorry i tried to make it better :[
Any clues?
no this is NOT a defective phone, its the result of the ROM and the 3 Button combo can´t work oh and you dont really mean deamon tools? and you musst plug the usb cable in the phone right before you hit enter or it can´t work!
I did that too. Like i said the phone turns it self off once the usb cable is attached.
Here is a brief video of my problem
-http-://-www-.youtube.-com/-watch?v=MtcCvfCbAFk-
remove all "-" from url.
dainiuxxx, this thread belongs in the Q&A section, not in development. Take a moment and read the "STOP, READ THIS BEFORE POSTING" thread at the top of both of these sections, it has clear guidelines for proper thread placement.
Sorry for that sirphukee.
Any help? Anyone?
Anyone that can help?
have you tried plugging it into another PC or Laptop?
Yup tried amothe laptop, reboot.
Wall charger, reboot.
So i`m kinda out of options?
yes, return it to the store, to get an exchange
a normal working SGS does not reboot when plugged into any USB port/charger
it's Shorted (damaged) for some reason
ok, return sounds good to me, but what will i have to say when they`ll switch on the phone and see the AT&T logo?
I`m in UK and my network is Orange UK.
Will they accept it back with no problems, i kinda doubt that....
uhh... you are in quite a pickle ...
try to remove the evidence, intentionally use a Update.zip ROM flash to kill the flash
or flash it to stock if you find a good ROM via Update.zip
use the WiFi to download the Update.zip ROM flash to the root of the internal SD to flash it.
ROM Manager can get the same results, you can WiFi install it from Market
AllGamer said:
uhh... you are in quite a pickle ...
try to remove the evidence, intentionally use a Update.zip ROM flash to kill the flash
or flash it to stock if you find a good ROM via Update.zip
use the WiFi to download the Update.zip ROM flash to the root of the internal SD to flash it.
ROM Manager can get the same results, you can WiFi install it from Market
Click to expand...
Click to collapse
Installed ROM manager from market, but seems it needs the phone rooted, right?
And rooting can be done only via usb cable, right?
Where do i find a Update.zip ROM via Wifi? and what are the procedures when i do find it?
OK,
so obviously the question now is HOW DO I F...k up my phone completely so no one could see what was done to it. When i`ll take it back to the shop.
dainiuxxx said:
Installed ROM manager from market, but seems it needs the phone rooted, right?
And rooting can be done only via usb cable, right?
Where do i find a Update.zip ROM via Wifi? and what are the procedures when i do find it?
Click to expand...
Click to collapse
you can ROOT the phone within the phone itself
by downloading Ryzaa One click lag fix from the market
instead of installing the lag fix, select the option to ROOT the phone
Same issue here. Amazing how easy it is to mess this phone up when you are really stupid. Oh well....
Tried the one click lag fix to root it, but cannot find a way to get into download or recovery mode. Tried every button combo I have seen suggested, but either gets stuck in a loop on the AT&T screen or just boots into the OS.
At the moment I feel my only option if we cannot find a way to get into download mode is to format the internal SD card and send it back to o2 (my provider), tell them it fried when Kies tried to do an update, cross my fingers and hope they send me a new one.

Categories

Resources