SD-Card Rom for Charmer - MDA Compact II Software Upgrading

Hi guys,
I have a big problem with my charmer.
At the begining I tried to work with my charmer and it was OK, but after a short time it resets from alone. It was the same situation everytime, when the charmer was starting and I did the calibration of the touch screen it was reseting always as soon as I pressed the cross on the right bottom.
Next step was to flash the ROM - it was sucessful, but the same situation
-> Reseting at the calibration.
I did once again a flash but it resetet during flashing and now I have the situation, that I can enter boot loader but as soon as I connect it resets.
Battery I checked -> It is OK.
So does anybody have a Rom on SD card ? -> I have no other joice, this is my last chance to get it running again.
Thanks for your help in advance
Best regards
Helldriver

Hi
1. Kill (task manager) wescomm.exe (this is related with activesync installed on your PC).
2. Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
3. Now connect your USB cable to your phone
4. Download T-Mobile compactii_aku2.0_05-2006 rom and Flash it works for me
jerry

Not working with USB
Thanks for your comment, but it is not working, due to the fact that the MDA tripps as soon as I connect the USB cable (even if I kill the wecomm.exe).
Therefore my only chace is the SD-card
So if anybody has a ROM on SD card, please help me getting my Charmer running again.
Regards
Helldriver

Hi Gents
is there somebody who can help me ?
I really need a SD-card rom
Thanks
Helldriver

Sorry ,but I am noob. How can i flash it??? And how can i kill wescomm.exe???

Rom backup
Hi all,
Still searching for the SD ROm image... Can someone upload?
Please...

Related

Windows Rom on SD Card

Does anybody hav a rom image that i could save to my SDcard since i cant connect the mda to my active sync
mikethegreat45 said:
Does anybody hav a rom image that i could save to my SDcard since i cant connect the mda to my active sync
Click to expand...
Click to collapse
If you haven't already, you can try putting the mda into bootloader mode directly. That way you don't need to use activesync. Then reflash your mda with a known working rom. Disconnect your mda from the usb, then do a ctrl-alt-delete, to pull up the windows task manager. Go to the processes tab, and select the wcescomm.exe process and then end the process. Now, put your mda in bootloader mode by pressing the camera button in and resetting with the pin hole. After a few moments, the bootloader (colors) screen will come on, and you can let go of the camera button. Now plug in the usb to your computer, and you should be able to flash your rom.
Good luck!,
sorry i tried that, unfortunately that didn't work either, is there any other way to update, im still on the factory rom it came with.

Battery Problem after upgrading with new uk t-mobile rom

Hi,
i upgraded my charmer with the new uk t-mobile rom and my nproblem is that the battery does not charge,and i don't know how to do
have you some suggestions???
Waiting your answer,thanks a lot,Antonio
Hi did you get a answer
Hi I have the ssame problem, did anybody come up with any ideas ?
Cheers
TBW
Battery Problem
Hi, I have too this problem with wm6 rom have you some suggestions??? pleas
Hi...nobody can help us???
Try plugging in the charger and when its plugged in, hit soft reset button with your stylus. Wait for the system to boot and see if it charges.
vlodeck said:
Try plugging in the charger and when its plugged in, hit soft reset button with your stylus. Wait for the system to boot and see if it charges.
Click to expand...
Click to collapse
i have the same problem and doesn«t work for me
Then my guess is you flashed a ROM not intended for your device.
now how i can solve this?
Reflash a charmer rom? And if that doesn't work, try a prophet WM5 rom.
it says that i don't have enough battery, is lower than 50%
Use the NO_ID RUU version instead.
i already try a few roms and i can't flash the pda with none of them
You will need to reboot in BootLoader mode first (powerkey+camera+reset).
hello!
a downgrade my Charmer and now the battrery is 0%, when i connect to usb phone don't want to start, on charger it startet but battery dont want to charge. help pls ...
Hi,
I have solve this problem but I'm not sure how I've done this.
1. dowlnoad cab from this link http://forum.xda-developers.com/showthread.php?t=327988
2. I have use program Wizard Service Tool and clear everything what is possible including format.
3. reset
4. format after strart camera+record+soft reset
5. after reset bootloader mode, and first time my phone has connet in BLmode with USB.
6. Then I have run original T-mobile RUU and it's working
My battery has been on 0% in system as well but after downgrade battery states about 70%
have a same problem.
did anybody else solve this problem? anybody used SD flashing method?
i've solved problem partly - now battery charges, but i can't start it without power supply. so what have i done:
1) i've downloaded ShellTool_bugfixed.zip (you can easily find it google).
2) unpack it.
3) copy Cert_SPCS.cab and EnableRapi.cab to you WM and install
4) extract nk.nbf from original Charmer ROM into ShellTool folder
5) start ShellTool.
6) press Get ROM Info
7) press Extract OS
10) press Flash OS
11) press ОК
Followed all this steps, now i've got an original charmer os, but bootloader is still from previous crap ROM. so there is trouble with starting it up. If you phone doesn't start even when you charging it from power socket, so try to wet contacts on battery - it should work.
now i thinking how to re-flash bootloader, cuz it cannot enter into bootloader witout power supply from socket. It's no possible to flash it from PC, cuz it cannot enter a booloader plugged into USB port. It seem that there is not enough power impulse to startup.

help me: Your OS ROM isn't customized for your hardware.

help meeee, i just flashed my diamond with this rom: RUU_Diamond_Dopod_CHS_1.39.706.1_Radio_Signed_Diamond_52.29.25.12_1.00.25.05_Ship.exe and after the restart it brings the message:
Your OS ROM isn't customized for your hardware. Please reflash the proper ROM code or contact the service center.
I've read in other posts concerning this message that i just need to take out the battery and wait 10-15 minutes. does not work for me. i still get the message:
Your OS ROM isn't customized for your hardware. Please reflash the proper ROM code or contact the service center.
I tried to flash it again, but the problem is that the diamond is not recognized on my computer anymore it looks like it doe sent have any usb connection capability any more.
Please help me.
Thank you soo much in advance.
P.s. Is there a combination of buttons to press so i can get the diamond in a flash mode so i can flash the proper OS on it?
come on guys, did i really brick my phone? does anyone have any idea what i should do now?
i had this same problem - take the battery out for about 2 minutes and then power it back on. that _did_ work for me. if you have done it and it didnt work i dont know.
simple question
do you have an original diamond or a dopod?
if you have an original diamond .... you flashed a dopod ROM on it..., did you put a HardSPL on it?
if you have a dopod...really dont know what happens with those ): sorry
Mariano.
i have an original diamond.
yes hardspl was on it.
i can go to the hardreset options by presseing home, vollume down and reset button. but this still doesent let me flash the orignal OS on the system.
what can i do, i really need your help guys!
i just found the solution by my self. the diamond must be shut down. just plug in the usb cable and plug it in in your computer. now, push the power on off button and vollume down at the same moment. the 4 collor flas display with the USB message comes, now flash your OS on it.
tataaa its done!
gmesut said:
i just found the solution by my self. the diamond must be shut down. just plug in the usb cable and plug it in in your computer. now, push the power on off button and vollume down at the same moment. the 4 collor flas display with the USB message comes, now flash your OS on it.
tataaa its done!
Click to expand...
Click to collapse
I had the same problem
and your solution (dear gmesut) works on it
only i can say thanks
gmesut said:
i just found the solution by my self. the diamond must be shut down. just plug in the usb cable and plug it in in your computer. now, push the power on off button and vollume down at the same moment. the 4 collor flas display with the USB message comes, now flash your OS on it.
tataaa its done!
Click to expand...
Click to collapse
good tip,it responded in my hd mini
thanks gmesut

Phone Struck on Tri Color Screen

Hello Guys,
I'm not sure if this is a right place to ask this question, but X1 is struck on tri color screen. Didn't do anyting, but since this morning... it's just not turning up.
Whenever I boot it up... shows tri color screen & say "loading"... cums back saying no image file & then again shows as following
KOVS110
SPL-0.78.0000
MicroP1-787
Microp2-707
Not sure if anyone else had this problem, but I'd appreciate if you can direct me to a place where it's already been fixed by someone else!
Thanks
Sachin Ghai
Try removing the battrey and wait for 10 seconds...if that helps ok, otherwise, U go in thr tri bootlader screen YOURSELF, (volume down+ power button) Do nothig, just go i the mode and come back..AGAIN< IM NOT AN EXPERT..IM JUST TRYING TO HELP U WITH UR PROBLEM....PLZ TAKE AN EXPERT'S ADVICE..
boLUCK!
Did the exact same thing...still struck at tri color screen...
All SM & Experts..I request you to get me out of this trouble..
Thanks in Advance
try to plug it to your computer via usb.. it happened to my diamond once.
I've already mailed you this
Hallo Sachin,
read the first post of this: http://forum.xda-developers.com/showthread.php?t=431218
You can use two methods, first your pc synced with your device and second the microsd procedure. i prefer the last one.
Here's the procedure for microsd: http://forum.xda-developers.com/showthread.php?t=445662
After you have done this, you can flash any rom you like, read this: http://forum.xda-developers.com/showthread.php?t=446070
So basically what you do is:
1) download hard spl
2) place it on a microsd card ( put it back in your device)
3) Hardspl from microsd ( is also in tricolorscreen)
4) Now you have hardspl'd your device.
5) download a preferred rom
6) put it on the microsd card
7) Flash.
Now your device must work again.
If you have any questions, mail me.
Greetz
If you are trying to flash a custom ROM you need hard-SPL. Follow the instructions the guy above gave to you.
Cheers!
cristidotro said:
If you are trying to flash a custom ROM you need hard-SPL. Follow the instructions the guy above gave to you.
Cheers!
Click to expand...
Click to collapse
I'm not trying to FLASH rom. I'm that techie to do all this.....However... thanx for ur efforts guys...Fortunately...the bootloader came in to normal mode & booted up in normal way... however I'm scared to off it again, as I'm not sure if it'll turn up in normal way again or not.
What do you guys think?
SHALL I HARD RESET or SOFT RESET my phone? WIll either of these solve the problem?
I don't want to play with ROM thing.... just lil scared not to turn my x1 in useless crap..

[Q] Stable release (20141018) of CM11.0 by NovaFusion causes a hard brick on my phone

Hi guys,
First of all sorry for my English.
I have a big problem after upgrading (l always did it without any problem until now) to New stable release (20141018) of CM11.0 (by NovaFusion) for S3 Mini via TWRP. Everything gone well until I rebooted the phone (as the installer asked to). Now, my phone has a boot looping and the TWRP doesn’t boot either - just stuck on at “teamwin” logo (recovery's logo). It seems, my phone is dead and has a hard brick. The only thing what is working on it is offline charging. PC doesn't recognise my phone via USB.
Please help me - what can I do in this case? Or my phone is incorrigible and the only thing I can do is throw the phone into the trash?
Thank you for your help!
Best Regards,
Barni
fdfrs said:
Hi guys,
First of all sorry for my English.
I have a big problem after upgrading (l always did it without any problem until now) to New stable release (20141018) of CM11.0 (by NovaFusion) for S3 Mini via TWRP. Everything gone well until I rebooted the phone (as the installer asked to). Now, my phone has a boot looping and the TWRP doesn’t boot either - just stuck on at “teamwin” logo (recovery's logo). It seems, my phone is dead and has a hard brick. The only thing what is working on it is offline charging. PC doesn't recognise my phone via USB.
Please help me - what can I do in this case? Or my phone is incorrigible and the only thing I can do is throw the phone into the trash?
Thank you for your help!
Best Regards,
Barni
Click to expand...
Click to collapse
Follow these steps:
1-take out the battery of your phone and wait 20 seconds.
2-reinsert battery.
3-firstly hold volume down then home key and at the last press power button (while holding volume down and home)
you will see your phone gets into download mode then flash stock rom with odin go here for stock rom type your phone model and download www.sammobile.com
qasim799 said:
Follow these steps:
1-take out the battery of your phone and wait 20 seconds.
2-reinsert battery.
3-firstly hold volume down then home key and at the last press power button (while holding volume down and home)
you will see your phone gets into download mode then flash stock rom with odin go here for stock rom type your phone model and download...
Click to expand...
Click to collapse
Thank you for your quick reply. After I finished downloading the firmware from the site you linked me, I will try your steps. Thank you very much.
One more question: do I need anything else before flash the stock rom via odin? For example kernel, bootloader, etc...
Thanks.
Edit:
Dear Qasim799 ,
Thank you for your help - everything gone like a charm .
Thanks for your help to solve my problem .
I am grateful to you .
Regards,
Barni
fdfrs said:
Thank you for your quick reply. After I finished downloading the firmware from the site you linked me, I will try your steps. Thank you very much.
One more question: do I need anything else before flash the stock rom via odin? For example kernel, bootloader, etc...
Thanks.
Edit:
Dear Qasim799 ,
Thank you for your help - everything gone like a charm .
Thanks for your help to solve my problem .
I am grateful to you .
Regards,
Barni
Click to expand...
Click to collapse
Your welcome.Kindly press ? thanks button uder the posts.

Categories

Resources