Related
Hello people,
I rarely see a burnt in (like old crt screens) image on the bottom of the screen.
For example when I change the volume, the softkey labels of the today screen are still visible, along with a white line. Most times it is normal so I don't worry very much but I'm wondering if someone else has the same issue.
I've tried many versions of hardspl (because they seem to be connected with some screen issues) but the problem still exists.
Hi i have the exact same issue, i put a post up a month ago not had any response on it. I have a MDA compact IV, not updated any ROM or HARDSPL yet. I was tempted to update to see if the problem could be rectified.
Have you update to a cooked rom? I might send mine back to have it fixed if its a screen issue.
Mine only holds the "burnt in image" along the right of the screen from top right corner to bottom right corner around 3cm in.
Also i have noticed the "Burnt in image" seems to get stronger when the device heats up. If i use GPS or 3G, this seems to affect the screen.
My background is black which makes it really noticable, i think if i stick with the orginal t-mobile white background it's probably not that noticable.
mmm
Perhaps the units you bought where like demo units. Those units that are displayed all day long turned for people to look at them. I have read in another forum that perhaps that distortion is caused by extreme temperatures, cold or heat.
well i'm still trying to figure out what is causing it, as I notice it only once in maybe a week. Maybe temperature is the most probable cause. For me I notice the defect only in gray background (e.g. when changing volume or launching opera).
My unit was from the first batch from expansys (origin htc asia)
It's possible your handsets have screens which are somehow susceptible to heat damage from inside the phone. This would be no fault of your own, but a manufacturing defect.
I'd suggest returning the phone to the retailer, HTC or the operator depending on your situation.
However, if you're using the phone in extreme conditions, ie low temperatures, you may very well find the LCD slow to refresh or have some level of image retention.
Let us know the outcome
i also have a ripple effect when pressing, but its more apparent with black. its also a first gen model, so i think ima make a phone call to htc. maybe a can get a new device.
for the burn in, try this:
1. Go to power settings, deselect automatic backlight management.
2. Pull up backlight level to maximum.
3. Reselect automatic.
You should be ok!
If not, faulty device!
tnyynt said:
for the burn in, try this:
1. Go to power settings, deselect automatic backlight management.
2. Pull up backlight level to maximum.
3. Reselect automatic.
You should be ok!
If not, faulty device!
Click to expand...
Click to collapse
Ok I will try this although I can't see how the backlight can affect the screen. In order to repair it with warranty I would have to send it to expansys uk (because it is not a European device) and I bet it would take long
Have you tried removing the battery for a while - some lcd screens can get the memory effect, and cutting power for long enough normally cures it.
My phone actually holds the previous menu under the current menu.
Example i'm on the home screen, goto messages and send a text using the qwerty keyboard. Back to the home screen, i can see a very faint image of the qwerty keyboard under the Programs hotkey.
When the PIN lock comes on the bottom right is "MENU", i can see a faint "programs" letters icon underneath it.
I will try and leave the battery out for a few hours, if not a call to t-mobile!
ok, i have the same "problem". even after a soft-reset the words CommManager
and Programs are still slightly visible in the boot screen.
but: as mentioned above, turning the device off for a couple of minutes cures
this, and the screen is dark as hell again!
really seems to be some kind of memory effect!
regards,
markus
Left the battery out for a few hours, made no difference. I guess is not a software problem.
will be giving t-mobile a call tomorrow!
:-(
I guess every htc device must have a flaw...
when it does it again I will try to take a photo of it and post it here
Hi same problem here.... See my post below..
http://forum.xda-developers.com/showthread.php?t=417629
I thought it was due to Spb Shell but no, now i'm happy i'm not alone..
But what solution for this??
I'm not worried about the burn in looks.. My worry is whether this behavior of the screen will progressively damge the screen???
I have been using the Diamond at full backlight.. Last few days i've put it down to minimum, but the problem persists!!!
ok, I think it happens when it overheats.
So that is why it is caused when charging.
wtf?
No its not due to overheating, coz LCD screen are supposed to tolerate temperatures upto 80degree C... Dont know if its related to electro magnetic radiation, may be looks like it's more after i use the network...
Hi another mate has this problem Andrew...
http://forum.xda-developers.com/showthread.php?p=2684406&posted=1#post2684406
Hi,
i sent my phone back to T-Mobile hoping they will fix this issue with the screen. Just received the phone and it looks like they have done nothing On the job sheet all it says is "Software updated"? The problem is still there!
I dont think there is a fix as such, it looks like this is the cause
http://www.practical-home-theater-guide.com/image-sticking.html
I'll try if i can get a completely white background and leave the screen on for a while at the brighest setting, if this will erase the screen issue?
the problem appears more often now on my device....
It does not have to do with heat afterall.
Why would the image "stick" when the phone is off? I mean that many times I see the symptoms right after I switch the phone on.
Do we have any screen experts in the forum?
viperone88 said:
Hi,
i sent my phone back to T-Mobile hoping they will fix this issue with the screen. Just received the phone and it looks like they have done nothing On the job sheet all it says is "Software updated"? The problem is still there!
I dont think there is a fix as such, it looks like this is the cause
http://www.practical-home-theater-guide.com/image-sticking.html
I'll try if i can get a completely white background and leave the screen on for a while at the brighest setting, if this will erase the screen issue?
Click to expand...
Click to collapse
After calling up T-Mobile and made a complaint saying nothing had been done by the repair centre, they gave up and agreed to give me a handset replacement. Received the handset today, looks like a refurbed one? Anyway my problem is now fixed. Left the phone on a while and it got pretty hot, no ghosting on the screen
The restore was a pain, Wifi didn;t work, the HSDPA didn;t work. But after a few hours messing around it's all up and running so far.
I know that many of you have disabled the "Fast Sleep" mode while making a phone call. Well what I'm wanting to do is just the opposite, disable (or lock) the touch screen entirely while making a call. The problem I'm having is that when talking on the phone I always end up touching the screen with my cheek and either accidentally end the call, call someone else, or whatever. I would like to have a utility which would lock the touchscreen maybe 5-10 seconds after a call is established. One of the hard keys or an i-pod type slider function would unlock the screen.
Does anyone know of a utility like this?
I do have the "fast sleep" mode enabled within Kaiser Tweeks. However, while the fast sleep mode turns off the screen to save battery power, it still wakes back up with just a touch.
I have an AT&T Tilt.
I've seen some discussion of S2U2 on this forum, but it appears that S2U2 is a whole new today screen. I would like to keep my today screen unchanged. I only want the screen to lock during a call.
NZuercher said:
I've seen some discussion of S2U2 on this forum, but it appears that S2U2 is a whole new today screen. I would like to keep my today screen unchanged. I only want the screen to lock during a call.
Click to expand...
Click to collapse
It is a lock not a today replacement. That is what I use.
Thanks parleyp, I guess I'll give s2u2 a try. The info that I've seen just seems rather complicated when all I need is a simple lock utility. Why is there discussions on s2u2 affecting the weather tab, clock display, background, etc?
Which version are you using on your tilt?
Would you be interested in something like that??
If so search for opal dialer in kaiser Rom development subforum.
I am fairly certain that you can just press the "power" button and shut the screen off. When you are ready to hang up, just hit the end button. This is not automatic, but it works for me.
yea, i was gonna say: what's wrong with just pressing the power button?
Calling all X1 medics, surgeons and miracle workers
Ok so last night the when i got out my car my X1 hit the ground in my pouch (leather ones) it beeps and i think nothing of it. When i take it out of my pouch i notice the screen is white.
So I do the following..
I try to reset via the power button..... no luck
Next i remove the battery, so obviously it works, so the phone boots up.
Now the interesting part, phone boots up completely when it comes the enter password numerical pad the touchscreen does not want to work.
So I use the qwerty to enter my code. Its works but still my screen it dead to touch.
So next i do a hard reset( maybe was not the best idea dunno?) and this where i am cause i cant get pass the "touch the screen to activate windows" bit to do the setup of windows.
I even tried installing the ROM again but still end up at the same screen.
So anyone got any ideas where the problem lies?
You guys think my touch screen has gone to heaven?
Anyone know if I can do a soft reset and upload to the stock ROM without using the touch screen and can it be done now that i cant get pass the set up screen?
Thanks guys
i believe there are some roms that doesn't require you to touch the screen to continue.
examples are roms using wm6.5. sometimes you have to confirm something, but you might get it done with the ok button.
Does the screen NEVER show any image or does it look normal until the touch-the-screen-exercise?
Hi
Well the touch screen comes up and seems to be active cause when the screen dims and you touch the screen it goes bright again.
Like i said i did a hard reset so now when i boot up i get to the screen alignment exercise and i cant get further than that.
It basically boots up as normal just cant use the touch screen.
When i rebooted the first time after it feel i managed to use the qwerty to log into the phone but i no able to use the touch screen.
I could see everything as per normal but the screen touch ability is gone.
Do any of you guys know if there is another url where i can find a UK Generic rom besides rapidshare as it looks like its going in for repair number 2.
I am just hoping i will able to to soft reset.
I did download a exe ROM file from the ftp site but got a file corrupt error when i tried extracting the file. I also noticed the file would have extracted as a image file. Is this correct as its the first time i have seen this.
Thanks
Are you using a screen protector?
i'm affraid to say, that it's broken digitizer
It doesn't do this every time, but quite often and it seems to be random as I can't make it happen by doing one thing in particular. So, I used the phone for whatever, and then put it down, wait for the screen to go off and then in between the screen powering off and the always on display coming on, I get what you see in the photo below, and also in the bottom left corner in tiny writing, it says something about screen powering down and then something else that flashes on too quickly to read.
What do you reckon? Thanks.
Apologies for the screen protector, not got round to fitting the Whitestone dome yet.
I tend to get that whenever I open the keyboard for the first time after opening an app like WhatsApp or Snapchat. I don't get it when turning off.
I also get it when I press the middle button to go home from within an app.
But then again, I also have the taskbar to swipe up whenever I need it, so I'm not sure if this is relevant to me.
I.e I don't have the taskbar set to be static
Non rooted, T mobile branded 3 month old note 8. No water damange, no drops etc.
Using chrome one miniute, set the phone down to watch a movie on my tablet, picked up the phone to check messages and boom. Screen is off. The phone works, I can even answer calls because I know where the answer button is on the screen, haptic feedback works, all indicator lights work. The phone screen remains off.
Tried a soft reset (tried hard reset too the best I could being I cant see the screen) and the phone seems to reset based on the vibration and indicator light patters but the screen remains off. It's as if a physical connection between the screen and the brains of the phone has been severed. Literaraly the weirdest thing that has happened to me in a decade of Android phone ownership.
Googled all the black screen issues with these phones and most of them are resolved with just a soft reset... some said that the phone is in it's lowest dimmed state and go to a dark room and i'll see it faintly and then can increase brightness... no luck...
Has anyone experienced this?
I would say it's a warranty job, just tried turning my brightness to zero and you can still see the screen.
I did have a similar problem on an old note that had root and custom rom though but I had somehow set the volume rocker to control brightness and it had lowered itself to minimum in my pocket
KEVIN88GT said:
Non rooted, T mobile branded 3 month old note 8. No water damange, no drops etc.
Using chrome one miniute, set the phone down to watch a movie on my tablet, picked up the phone to check messages and boom. Screen is off. The phone works, I can even answer calls because I know where the answer button is on the screen, haptic feedback works, all indicator lights work. The phone screen remains off.
Tried a soft reset (tried hard reset too the best I could being I cant see the screen) and the phone seems to reset based on the vibration and indicator light patters but the screen remains off. It's as if a physical connection between the screen and the brains of the phone has been severed. Literaraly the weirdest thing that has happened to me in a decade of Android phone ownership.
Googled all the black screen issues with these phones and most of them are resolved with just a soft reset... some said that the phone is in it's lowest dimmed state and go to a dark room and i'll see it faintly and then can increase brightness... no luck...
Has anyone experienced this?
Click to expand...
Click to collapse
Try pressing and holding Volume down and power button for 5 to 7 seconds to force power off, then try to boot to download mode Volume Down + Bixby + Power button and see if the download mode screen shows......if not then probably a bad screen.
Sent from my God Mode 8
Tried it......nothing.....warranty job it is.... Bummed to have some refurnished phone in exchange for a Brand new 900 dollar phone just a few months back?
KEVIN88GT said:
Tried it......nothing.....warranty job it is.... Bummed to have some refurnished phone in exchange for a Brand new 900 dollar phone just a few months back?
Click to expand...
Click to collapse
Yeah that sucks, i can imagine..... i too hate the idea of refurbished units being swapped for warranty....bs, should be brand new unit!
Sent from my God Mode 8
so I had it replaced under warranty through T mobile. Refurb phone will come in today. One quesion. Should I let the Tmobile techs do the data/settings transfer from old phone to new one or just do everything myself from scratch (which will obviously take longer).
This happened to my phone twice for the past month or so. (both in Nougat and Oreo - Non rooted) Black screen but phone seems to be responding -- I can receive calls and notifications etc -- And force reboot doesn't fix it. I've also tried drainging the phone when it first happened to me but doesn't work. HOWEVER, it gets okay so randomly. Like I just left it for couple of hours and it just worked when I hit the power button.
I did tried bringing the device to Samsung but what they did is to just manually upgrade/reset the software in their end which I could have done in my part but I just let them do it. They told me to come back if it happens again which is kinda BS.
I can conveniently say this is a Hardware issue. I will wait for it to happen again on my phone and request for a replacement. Phone is 4 months old when it first happened.
I have the same issue with blank screen but phone is working.
It started couple of weeks after i dropped my phone on the ground. There is black dot on my screen and broken glass but phone was working ok and was still pretty usable. But then it started:
Display works fine but when i switch display of, lock the phone or display switched because of its timer it didn come switch on... But phone works, i can use it with blank (black) screen.
I had to do force restart so the display will turn on with samsung logo and booting screen, and keep on till another switch of.
I was trying every setting (but no hard reset) and then i found a little hack:
When you turn on the "Always On Display" (AOD) function you can let the screen switch off or do it manually, wait for 1-2 sec and always on display will come up to the screen. Then when you press home button or lock button screen will swtich on normally. YOu can type pin and use phone witch screen working. But when you try to unlock from "AOD" with your finger or your eyes it unlock but with screen black.
So i was using it like this. everytime you need to wait second untill AOD comes up, but it was working fine.
Problem nu 2 is that now it stop working, AOD is working but when i want to switch screen on from AOD it shows black screen and phone is working on blind.
So everytime after my screen goes black or to AOD i have to unlock the phone blindly and "Force restart" it and have to keep waiting until boot, and then have to never let phone to screen of.
Its not usuable.
¨
Now what do you think? Is it hardware problem or software problem? Because screen is working but randomly. The black dot of dead pixels on the screen is getting slightly bigger in time (about 1 year) but its like 1.5cm round. Maybe this cause the problem? And why hack with AOD was working for half a year and then stoped working? There wasnt any updates right before, but i tried to install some apps (non display related) so ill try to uninstall them.
Hawe you got any idea if i can repair it on my own even if i loose the waterproofability?
Or can it be replaced for free if i have a warranty? (I dont have insurance)
Thanks for your tips guys.
Reprocrastinator said:
I have the same issue with blank screen but phone is working.
It started couple of weeks after i dropped my phone on the ground. There is black dot on my screen and broken glass but phone was working ok and was still pretty usable. But then it started:
Display works fine but when i switch display of, lock the phone or display switched because of its timer it didn come switch on... But phone works, i can use it with blank (black) screen.
I had to do force restart so the display will turn on with samsung logo and booting screen, and keep on till another switch of.
I was trying every setting (but no hard reset) and then i found a little hack:
When you turn on the "Always On Display" (AOD) function you can let the screen switch off or do it manually, wait for 1-2 sec and always on display will come up to the screen. Then when you press home button or lock button screen will swtich on normally. YOu can type pin and use phone witch screen working. But when you try to unlock from "AOD" with your finger or your eyes it unlock but with screen black.
So i was using it like this. everytime you need to wait second untill AOD comes up, but it was working fine.
Problem nu 2 is that now it stop working, AOD is working but when i want to switch screen on from AOD it shows black screen and phone is working on blind.
So everytime after my screen goes black or to AOD i have to unlock the phone blindly and "Force restart" it and have to keep waiting until boot, and then have to never let phone to screen of.
Its not usuable.
¨
Now what do you think? Is it hardware problem or software problem? Because screen is working but randomly. The black dot of dead pixels on the screen is getting slightly bigger in time (about 1 year) but its like 1.5cm round. Maybe this cause the problem? And why hack with AOD was working for half a year and then stoped working? There wasnt any updates right before, but i tried to install some apps (non display related) so ill try to uninstall them.
Hawe you got any idea if i can repair it on my own even if i loose the waterproofability?
Or can it be replaced for free if i have a warranty? (I dont have insurance)
Thanks for your tips guys.
Click to expand...
Click to collapse
If you're under warranty it will likely be a free repair, unless they find other damage. Like moisture damage.
As far as fixing it yourself, it's just about as cheap to have Samsung do it than it is to buy the parts yourself. It's $229 for Samsung to do it, and you'll maintain the water resistance rating.
same has happened to me
KEVIN88GT said:
Non rooted, T mobile branded 3 month old note 8. No water damange, no drops etc.
Using chrome one miniute, set the phone down to watch a movie on my tablet, picked up the phone to check messages and boom. Screen is off. The phone works, I can even answer calls because I know where the answer button is on the screen, haptic feedback works, all indicator lights work. The phone screen remains off.
Tried a soft reset (tried hard reset too the best I could being I cant see the screen) and the phone seems to reset based on the vibration and indicator light patters but the screen remains off. It's as if a physical connection between the screen and the brains of the phone has been severed. Literaraly the weirdest thing that has happened to me in a decade of Android phone ownership.
Googled all the black screen issues with these phones and most of them are resolved with just a soft reset... some said that the phone is in it's lowest dimmed state and go to a dark room and i'll see it faintly and then can increase brightness... no luck...
Has anyone experienced this?
Click to expand...
Click to collapse
This has just happened to my note 8 too. I was about to update it and had started it. set my phone down and picked it up and phone screen is black but can hear the haptic feedback.
I can only see the lock screen and the notifications. Everytime I try to unlock my phone I only get to see a glimpse of the notescreen and then the screen turns black. Even when I try to go to camera through the lock screen the screen goes black too. When I charge my phone it heats up so I haven't really charged it as well. Has this also happened to anyone? It seems as if the phone's sensitivity still works in all places but when I unlock it the screen just goes black.
I also have problem of freezings and always rebooting. Tried soft and hard resets/factory reset. Still same problem. This phone has hardware issue. Do not buy.
I realize this thread is quite old but I have this exact same issue now. I have managed to discover some other information by playing around with various settings which are noted below. To begin with, I was able to used the AOD hack posted above for a while but it no longer works. The only way I can get my screen to come back is with a soft reset - but as soon as the screen times out or i turn it off, it goes black, with or without AOD enable. All the on screen buttons still work as well as the haptic feedback - I just can't see anything.
Now on to what I have found:
One thing I have found is if I turn off adaptive screen brightness and crank the brightness slider to the right, when it goes black I can faintly see some of the buttons - enough that I can turn the phone off or restart it from the power menu (If I switch the default setting to night that also helps to see the buttons a bit better). Also, if I enable night mode I can also see the brightness slider faintly but when I slide it left, it just makes the screen completely black and when I slide it right, it only returns it to the very faint brightness level.
So at this point I am stuck. To summarize the issue:
1. When the screen either times out or turns off, it is still "alive" but goes black. It will not return to normal brightness.
2. Turning off adaptive brightness and cranking brightness slider to right allows you to see faint buttons after screen times out but won't return to normal brightness.
3. Enabling night mode helps to see the faint buttons, in particular the brightness slider a bit better. However the screen still cannot return to normal brightness.
4. The only way to get the screen back to full brightness (albeit temporarily until the next timeout) is to turn off the phone or reset from the power menu; or soft reset holding volume down + power simultaneously.
Hopefully someone else has figured out a way to recover this. I am on Android 9 with Samsung UI 1.0
Phone is completely stock, never rooted and completely out of warranty.