Related
Hello Everyone,
My BA is stuck at the Splash Screen, I suspect that the Bootloader is corrupt. Does anyone know how to flash it?
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
imatrix
imatrix's suggestion.
@imatrix
Followed the steps before, and followed them again.. I'm still stuck.
Something interesting happened though:
There are two horizontal stripes across the splashscreen now.
I already tried to flash the OS, It doesn't work with the standard imate flash executable (It used to work before) and now I'm getting a 'MODEL ID ERROR' when I try to flash it using the BAupgrade... executable.
I tried with the MAupgradenoid tool, it flashes but I still get stuck on the splashscreen...
Thanks,
Wadih
BlueAngel Bootloader
Anyone has a way to either dump a bootloader file for the BA (Providing the file of course) or alternatively directives to copy it from another device (From the same make, i.e. Imate PDA2K) ?
Many thanks,
Wadih.
try this
http://forum.xda-developers.com/viewtopic.php?t=49611&highlight=model+id+error
imatrix
@imatrix
imatrix said:
try this
http://forum.xda-developers.com/viewtopic.php?t=49611&highlight=model+id+error
imatrix
Click to expand...
Click to collapse
I did, but as I specifed in me earlier post, eventhough the MAUpgradenoID flashes the files, I still get stuck at the splashscreen.
Interesting point: After flashing witht the MAUpgradenoID, I try reflashing back with the BAupgradeid.. I get the Model Error ID error back..
Something in the BA is wrong, and I believe it may be in the Bootloader. So, is there a way to replace the bootloader itself?
EDIT: By the way, I can't seem to be able to place a WM5 rom instead of the WM2003, although the flashing procedure starts, it quickly ends (i.e. without the percentage bar appearing) and says that the flashing worked successfully... But nothing gets actually flashed.
Many thanks for the help imatrix.
Regards,
Wadih.
hey,
check this out http://buzzdev.net/component/option,com_remository/Itemid,100/func,select/id,38/
but i have to warn you, replacing a booter is very dangerous, anything goes wrong during process will kill your device. so please handle with care.
imatrix
@imatrix
imatrix said:
hey,
check this out http://buzzdev.net/component/option,com_remository/Itemid,100/func,select/id,38/
but i have to warn you, replacing a booter is very dangerous, anything goes wrong during process will kill your device. so please handle with care.
imatrix
Click to expand...
Click to collapse
Thanks for the link, but how do I copy/get a clean boot bin file? (Which app, syntax, etc...)
Cheers,
Wadih.
BlueAngel froze on isalling wm6.5
much respect 2 all.I'm new here.i tried installing wm6.5 on my Blue Angel i tried putting it on a memory card i pressed power reset hold Camera and Record no luck. i didn't noticed this rom is for the Touch Diamond.i opened the file in the memory card and there was many files.i installed a few files i clicked one file and it froze.what i got is message serial on the top the screen and on the bottom of the screen is v1.02.i also tried sync it with computer no luck.can some one please help me and direct me 2 get wm6.1 because when Blue Angel 6.5 i was directed for the Touch Diamond rom.much respect.thanx a million thanx in advance.lol.
---------------------------------------------------------------------------
Learn 2 live & live 2 learn.learn 2 listen & listen 2 learn.Live 2 love & love 2 live.
We live 2 die & we die living.
life is what u make of it
BlueAngel froze on installing wm6.5
much respect 2 all.I'm new here.i tried installing wm6.5 on my Blue Angel i tried putting it on a memory card i pressed power reset hold Camera and Record no luck. i didn't noticed this rom is for the Touch Diamond.i opened the file in the memory card and there was many files.i installed a few files i clicked one file and it froze.what i got is message serial on the top the screen and on the bottom of the screen is v1.02.i also tried sync it with computer no luck.can some one please help me and direct me 2 get wm6.1 because when Blue Angel 6.5 i was directed for the Touch Diamond rom.much respect.thanx a million thanx in advance.lol.
---------------------------------------------------------------------------
Learn 2 live & live 2 learn.learn 2 listen & listen 2 learn.Live 2 love & love 2 live.
We live 2 die & we die living.
life is what u make of it
100/100 work
imatrix said:
try this for whoever get stuck at boot screen or in bootloader mode
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into Bootloader Mode by pressing Power + Record Button and Soft Reset.
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
imatrix
Click to expand...
Click to collapse
thaks br very good
Hi, I have the problem, that windows does not recognize the Blue Angel any more, so no "WCEUSBSH001" available. Any help??
Thx
Hi,
Can anybody please help me with this proble,
I am freaking.
I bought the phone SX 66 (Cingular) a week back and thought will download some cool things in the weekend.
I thought of upgrading the Rom.
The sequnce was confusing.
So I downloaded BAUpgradeUt file , EntelBL, GetDeviceDte, HTCRUU.DLLHTCRUU.cnf and xda3nbftool files on to a temp folder.
I guess I executed the BAUpgradeUt file (with Activesync on) and the phone was on the cradle connected to my laptop.
It restarted and went to a mode where the screen started showing USB v2.07
I removed the battery and tried restarting by pressing the power button, it showed serial V2.07 (as it was not connected to the cradle)
I waited for the battery to dry down but nothing is happening.
Now when i connect it back to cradle, it says USB V2.07
I am really worried.
Its a little difficult to understand fro the XDA forums, so can anyone help me step by step on how to fix this.
I mean which file do i need to execute.
Should i disconnect anything?
Pls explain in detail as i will miss out again and dont want to loose this.
I have unlocked this successfully erlier
Awaiting the earliest reverts
Thanks
Abhi
[email protected]
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Hi Midget, Thank you for the patience and being there.
I am sorry but I am still stuck with this.
Like mentioned by you,
1. downloaded mtty1.42.rar onto a temp fold on my laptop
2. Stopped wcescomm.exe from taskbar(the rapimgr was not running so dint get it)
3. Device was put into cradle (was saying USB v 2.07)
4. I executed the mtty1.42 extracted file(application)
("This is where I got stuck")
I got
open port setting popup
a. Asked me for Port (options were COM1,2,3 and USB)
I selected USB
b. Asked me for Baud:
I selected 115200
c. Databits = 8bits
d. Stopbits = 0bits
e. Localecho=No
f. Flow Control=None
e.Parity=None
When I say Ok, It opens me a window of Multi Port TTY Version 1.42 and within that there is another window that is opened that says
USB115200 N-8-1 and its a blank notepad kind of a file
(Do I need to type in anything into this and save and and download?)
5. U have instructed me to
a. Choose WCEUSBSH001 (where do i choose this from?)
b type "set 14 0" without the quotes to tell bootloader to boot the OS after reset. (where do I do this)
c. type "task 28" to get your device formatted (where)
d. type "task 0" to ask your device reboot (where)
6. take the device out of the cradle, and manually reset it if it does not do that already(I was not able to reach this stage).
Please take a little time in guiding me and sorry if I have been troubling you with basic questions and I m very worried and want to fix this sooner.
Also is it required for the phone to be charged suring this process and is it mandatory that I should ensure that it reads USB v2.07 while it is on the cradle?
Awaiting ur instructions and Thanks again s much
Abhi
Midget_1990 said:
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Click to expand...
Click to collapse
everything is fine, just type what i said into the 'notepad' window, pressing eneter after each line and removing the quotes, then remove from cradle and hard reset your phone
Hi,
I am very sorry, but I need help.
I am unable to fix this.
I am trying my best to follow the instructions and dont know where am i going wrong.
Like U said,
I went again with the Multi Port TTY utility and in the new USB text file window, ((stopped the wcescomm.exe application from taskbar)
I tried entering
set 14 0
USB>task 28
USB>task 0
USB>
Saved the file as USB
The phone in the cradle was still showing USB v2.07
I took the phone out of the cradle, removed the battery and inserted it back into the cradle
and i again starts showing USB v2.07
Where am i going wrong..
I also tried
USB>set 14 0
USB>task 28
USB>task 0
USB>
but in vain...
Please help in resolving this
Thanks
Abhi
Midget_1990 said:
everything is fine, just type what i said into the 'notepad' window, pressing eneter after each line and removing the quotes, then remove from cradle and hard reset your phone
Click to expand...
Click to collapse
I got same problem couple of days ago.
i tried this way, and it works for my PDA. but the only thing is my siemens sx66 bluetooth does not work any more, and tell me the license is expired. anyone knows the reason? i think the exrom wrong.
thanks.
andy xia
Midget_1990 said:
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Click to expand...
Click to collapse
I ****ed my BA like this guy and found this solution via google.
It worked perfectly. God bless you sir.
Stuck in Serial
The BA that I have killed is stuck in "Serial, v2.07". Placing it in a USB cradle does nothing. I have tried to connect using a cable I purchased, but I think I need a straight thru cable and I only have a null modem.
I want to verify that I should be able to connect via serial and do the same process?
Thanks.
padapa
i had ewhat a similar issue, my problem was caused by windows vista....not sure if thats what your issue is, but if you are running vista try this...
http://forum.xda-developers.com/showthread.php?t=291723
still in stuck serial
After a long break, I'm back to trying to recover this BA that is stuck in bootloader. I've read wiki's and forum posts till I'm blue in the face. I have two BAs, one with WM2003 and the "stuck one".
If I put the good BA into the cradle, it starts Activesync and the USB driver and I can connect via mtty and see the good BA, the "stuck one" does not start anything.
If I plug in my serial cable and put in the good BA, I see the "CLIENT" message. When I put in the "stuck one", I see nothing and typing the codes does nothting.
Any ideas would be greatfully appreciated.
Padapa
check the bottom PC IO/Connector of the BA physically for broken "pins"
Midget_1990 said:
1. Download mtty v1.42 from http://files.pdamobiz.com/ROMs/XDA/mtty1.42.rar
2. Stop ActiveSync, by Task Manager (press Ctrl + Alt + Delete)
kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
good luck.
Click to expand...
Click to collapse
Not working bro :S
had the same prob here.
im back after a break. i gave up.
i think what i did wrong was using the usb hub. and since you had the issues w the cable... maybe....
im still looking for an answer.
lets see if we can make it.
follow the instructions as they may help.
these brains are good.
i posted this thread but im sure you already know.
http://forum.xda-developers.com/showthread.php?t=346510
Hello!
Where I can download mtty for Trinity?
http://wiki.xda-developers.com/uploads/mtty.exe not working!!!!
Hello, so that its it functions is necessary to neutralize (wcescomm.exe) ActiveSync and then to select port USB in mtty.exe.
I have SPL-1.01 MFG, but......
USB> task 32
Level = 0
Cmd>lnb C:\finalsplash.nb 500e0000
:F=C:\finalsplash.nb
:A=501A0000
:O=00000000
:L=FFFFFFFF
start NB image download
Click to expand...
Click to collapse
On this step, process stoped
BE WARNED THIS ROM ADDRESSES ARE FOR HERMES, NOT FOR TRINITY... flashing the wrong address can brick your device!
you have to use mtty 1.16 for the lnb command to work.
Take it from here:
ftp://xda:[email protected]/Hermes/Cooked_ROMs/SPL-1.01MFG_Pack.zip
pof said:
BE WARNED THIS ROM ADDRESSES ARE FOR HERMES, NOT FOR TRINITY... flashing the wrong address can brick your device!
Click to expand...
Click to collapse
Say me, please ROM adress for Trinity!
Sorry, my English very bad....
lvsw said:
Say me, please ROM adress for Trinity!
Click to expand...
Click to collapse
sorry I don't have a Trinity and I don't know what is the ROM layout on it, you can investigate yourself capturing the output of the RUU while flashing a rom with usb monitor, dumping rom parts with rbmc bootloader command, and dumping mmu and parts of mem from gnuharet... but it's a long process until you manage to get all the addresses correctly. You have to compare what you get from the device with the *.nb file extracted from the NBH to see where each part of the ROM starts. Can't really do this without having a Trinity on my hands
Problem using mtty
I have some ploblems using mtty.... I deselect "connect to USB" in pc activesync, then I connect the pocket pc on the usb cable, then I start mtty and I select USB.... I have a the mtty window in which is written CLIENT then, again, CLIENT, and the pocket pc... CONNECTING TO USB... and this situation remain without any changement.... where I am wrong?
pof said:
you have to use mtty 1.16 for the lnb command to work.
Click to expand...
Click to collapse
Actually, the LNB command must be implemented in the bootloader to work. If you connect to Trinity using any version of MTTY (from 1.10 to 1.46) and type LNB, it will just give an "Command error!!!" message.
yes, but seems to be implemented on the MFG bootloader version that is left on the device after unlocking it with imei-check unlocker, isn't it?
can't get MTTY to connect w/ Trinity
dr-jo said:
Hello, so that its it functions is necessary to neutralize (wcescomm.exe) ActiveSync and then to select port USB in mtty.exe.
Click to expand...
Click to collapse
Not that I think it should matter much but in case it does I'll say first that I'm running a PC w/ Vista and not xp or earlier.
Anyway, I can't get MTTY to connect to my Trinity.
The only port that MTTY can open is my Com3. All other ports, inluding the one titled "USB" can not open.
When I have MTTY open on Com3, there is no response to any command so I suspect although the application is occupying the port, it is not communicating w/ the Trinity.
Can anyone provide some insight here or tell me the correct com port settings (parity, baud, stopbits, etc)?
Thanks,
J
I tried MTTY on my WinXP notebook as well. I get the same situation. I downloaded a freeware terminal emulator application also but wasn't able to establish coms w/ the Trinity either.
Can someone confirm their com settings in MTTY?
The same thing has happened to me on p3400i, the New Gene, followed the guide at XDA to every letter, though I knew my device was a new Gene. Now the mtty program opens with some settings window instead of the USB button. Only port accessible is COM3. Flashed and bricked by Olipro SPL.
I Recentley Tried To Upgrade To The Latest ROM So I Went To The O2 UK Website And Downloaded Xda_IIs_Upgrade_v140242.exe, About Half Way Through The Upgrade My Computer Froze And I Had To Re-Start It.
Now My XDA IIs Wont Turn On And When I Put It In Its Cradle The Power Light Turns Red....Not Orange But Red. I Have Tried Running Xda_IIs_Upgrade_v140242.exe Again But I Just Get;
ERROR 101: CONNECTION ERROR
Is There Anything I Can Do Or Is It Terminal?
Thanks
huh!
can u enter into bootloader mode? press POWER + NOTES + RESET BUTTONS? if it does, it can be upgraded again........ try it
No Luck
Just To Make Sure, The Notes Button Been To The Left Of The Speaker? I Have Tried Holding All 3 At Once And Nothing Happens. I Dont Have My Mains Cable In, Will That Matter?
Fingers Crossed
After Removing The Battery And Re-Inserting It And Following Your Instructions I Am Doing An Upgrade At The Moment, I Will Let You Know How It Goes....Thanks For Your Help
Error 112 : Ce Rom Update Error
ERROR 112 : CE ROM UPDATE ERROR
Any Ideas?
i see!
remove the battery for about 30 mins. after that reconect and then see if it has power! try POWER + RESET. f no luck, then the problem is in the boot process mode! i think there is a way to revive it somewhere here........ just try to search the forum...... gud luck let me know if you found a way!
error
colhatty said:
ERROR 112 : CE ROM UPDATE ERROR
Any Ideas?
Click to expand...
Click to collapse
are you upgrading from the same provider with the previous rom? meaning from O2 to O2 not O2 to imate roms or other roms..............
try mtty method, you may have screwed a lil your device
1. Download mtty from the attachment
2. Stop ActiveSync, by Task Manager (press Ctrl + Shift + Escape) kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001 (or just USB in port) and press OK
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
After this procedure reflash
Thanks xplode,
I had a simialr problem as colhatty where my Xda IIs was just displaying USB when plugged into the cradle, following your steps I was able to reset the device and get WM 2003 SE to boot.
PDA2K dead
while upgrading with several attempts my PDA2k is almost broken it has only the colored page and nothin else , i treid your SW actually i dont know exactly how to use for example is thier any thing else to do after righting the commands
/ shall i save it? what to do? in all means nothin happen any help
HOWTO: Reinstall existing ROM without touching Extended ROM or Upgrading/Downgrading
The following methods allow you to get rid of all user data on the device (except for memory recognised by the resident system as being storage cards).
>>> METHOD A -> Device Only (recommended, faster)
1) Use two fingers to simultaneously press the RECORD and CAMERA buttons of the phone (on the phone's left side). Whilst these two buttons are depressed, use the stylus to click the soft-reset button underneath the phone - keep the two buttons depressed until the boot loader screen appears.
2) This should enable three options on the boot screen. These options allows a YES/NO response. Use the RECORD and CAMERA buttons to navigate between the options, and switch the YES/NO values. Set the following:
1] Enable KITL: NO (this is a debug tracing option which isn't required, except possibly for developers)
2] Format Registry Hive: YES (clears the registry)
3] Format Storage: YES (formats the internal memory: "\" directory, and under "\RamDisk\". Items under any storage card "\Storage Card\" are not formatted).
3) Once these options are set, press the MAIL button (in between today and the Pocket IE button) to confirm these options, and continue with the Registry and Storage format.
4) The device performs the reset, and the Windows CE setup screens (ie. screen alignment etc.) appear. Continue as per a new install.
>>> METHOD B -> Mtty
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
2) Phone needs to be POWER + Record + Pen Reset and on Serial/USB screen. COnnect it to the PC, and it should show USB, with the backlight remaining off.
3a) Run mtty1.42.exe. (or the attached mtty application)
b) Select USB from first list (where COM1 is displayed. Don't press USB button). If USB (or a list item containing USB) isn't in the list, then you have't connected to the PC properly.
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
c) Click OK
3) Run following commands:
[press enter first to get USB> prompt]
USB>
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
USB>set 14 0
HTCST ÚÈHTCEUSB>
6. type "task 28" to get your device formatted
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
7. type "task 0" to ask your device reboot
USB>task 0
USB>
8) Exit the program, then re-hard-reset (POWER + Record + Pen Reset), leaving on USB screen in order to run ROM Flasher
i will try and answer you soon but i think my problem accured because i'm using windows vista and windos mobile center service SW
Windows CE USB
colhatty said:
I Recentley Tried To Upgrade To The Latest ROM So I Went To The O2 UK Website And Downloaded Xda_IIs_Upgrade_v140242.exe, About Half Way Through The Upgrade My Computer Froze And I Had To Re-Start It.
Now My XDA IIs Wont Turn On And When I Put It In Its Cradle The Power Light Turns Red....Not Orange But Red. I Have Tried Running Xda_IIs_Upgrade_v140242.exe Again But I Just Get;
ERROR 101: CONNECTION ERROR
Is There Anything I Can Do Or Is It Terminal?
Thanks
Click to expand...
Click to collapse
I have the same problem with my O2 XDA IIs, this is how I resolved the problem.
1- Take the battery out
2- Put Battery on while holding onto Power Button and Record
3- Now the PC shoud recognise a Windows CE USB
Now you can updategrade or downgrade.
xplode said:
try mtty method, you may have screwed a lil your device
1. Download mtty from the attachment
2. Stop ActiveSync, by Task Manager (press Ctrl + Shift + Escape) kill two processes rapimgr.exe and wcescomm.exe
3. put your device into the cradle
4. Run mtty (from downloaded) Choose WCEUSBSH001 (or just USB in port) and press OK
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
6. type "task 28" to get your device formatted
7. type "task 0" to ask your device reboot
8. take the device out of the cradle, and manually reset it if it does not do that already.
After this procedure reflash
Click to expand...
Click to collapse
After step 4. mtty alerts with "USB port cant open". What now?
On your phone, when connected, ensure that at the top of the screen, it says "USB", not "Serial". Also ensure you've killed the ActiveSync processes properly.
Also consider:-
* Are you able to use ActiveSync to sync when not following this process?
* Does USB appear in mtty as a connection option?
Ayo said:
After step 4. mtty alerts with "USB port cant open". What now?
Click to expand...
Click to collapse
use this mtty
http://file2upload.com/file/33883/mtty-rar.html
CJBS said:
On your phone, when connected, ensure that at the top of the screen, it says "USB", not "Serial". Also ensure you've killed the ActiveSync processes properly.
Also consider:-
* Are you able to use ActiveSync to sync when not following this process?
* Does USB appear in mtty as a connection option?
Click to expand...
Click to collapse
Done all that... And still "USB port cant open" - I'm using Windows Vista Ultimate... So Might this be a problem for "Mtty"?
(BA_WM5_AKU3.5_R4-xplode.lazy.release(2).rar
Help , I tryed to burn a new rom (BA_WM5_AKU3.5_R4-xplode.lazy.release(2).rar) on my O2 XDA 3. After starting the installation I got a Connection Error and now the screen displays "Serial" and "V2.06". Hard and Softreset does not boot the PDA. What can I do to make the machine working? Can anybody help?
I did all instructions right (Copy ..to Storage Card)
firtst I had an eplus rom.
Installing my next ROM was the latest from the O2 page.
Then I tried AKU3.
you know the rest...
Thany for helping,
Thomas
I found everything I needed. Thanks to all others for the great stuff here.
And it burns burns burns...
CJBS said:
The following methods allow you to get rid of all user data on the device (except for memory recognised by the resident system as being storage cards).
>>> METHOD A -> Device Only (recommended, faster)
1) Use two fingers to simultaneously press the RECORD and CAMERA buttons of the phone (on the phone's left side). Whilst these two buttons are depressed, use the stylus to click the soft-reset button underneath the phone - keep the two buttons depressed until the boot loader screen appears.
2) This should enable three options on the boot screen. These options allows a YES/NO response. Use the RECORD and CAMERA buttons to navigate between the options, and switch the YES/NO values. Set the following:
1] Enable KITL: NO (this is a debug tracing option which isn't required, except possibly for developers)
2] Format Registry Hive: YES (clears the registry)
3] Format Storage: YES (formats the internal memory: "\" directory, and under "\RamDisk\". Items under any storage card "\Storage Card\" are not formatted).
3) Once these options are set, press the MAIL button (in between today and the Pocket IE button) to confirm these options, and continue with the Registry and Storage format.
4) The device performs the reset, and the Windows CE setup screens (ie. screen alignment etc.) appear. Continue as per a new install.
>>> METHOD B -> Mtty
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
2) Phone needs to be POWER + Record + Pen Reset and on Serial/USB screen. COnnect it to the PC, and it should show USB, with the backlight remaining off.
3a) Run mtty1.42.exe. (or the attached mtty application)
b) Select USB from first list (where COM1 is displayed. Don't press USB button). If USB (or a list item containing USB) isn't in the list, then you have't connected to the PC properly.
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
c) Click OK
3) Run following commands:
[press enter first to get USB> prompt]
USB>
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
USB>set 14 0
HTCST ÚÈHTCEUSB>
6. type "task 28" to get your device formatted
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
7. type "task 0" to ask your device reboot
USB>task 0
USB>
8) Exit the program, then re-hard-reset (POWER + Record + Pen Reset), leaving on USB screen in order to run ROM Flasher
Click to expand...
Click to collapse
I am trying your plan B I got the mitty up but I am unable to type into the screen
Hi i have a vodafone VPx, and i hard reset it and now it is stuck on a 4 colour screen it says Made BY D-TWO
R: NONE
G: NONE
D: W6.5.X
i tried putting it i bootloader mode but i get a white screen when i press the mail button. PLEASE help me and provide me with all the links as i am a TOTAL NOOB i got my VPx yesterday so i dont know anything and this is my first WM phone. I do not know what rom it is using as i bought it with it already upgraded. please help
thanks
RECORD+CAMERA+RESET for a few seconds put this options like it:
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
with RECORD you move and with CAMERA change the values, at the and press MAIL.
tried that before it gets stuck on a white sreen
oh and i put my phone in boot loader mode and installed wm6.5 but it is not successful please someone send me link to wm 2003 se
Here the link for win mobile 2003 se but is for qtek 9090, i don't know if is good for your device http://www.megaupload.com/?d=PC047PQD
[SOLVED] Stuck at 4 color Screen
OH if this is helpful i will put your name in my Sig you are the best thank you i wish it works
it should work it is the same as the QTEK 9090 just looks different
EDIT: it didn't work extended ROM ERROR UPDATE ERROR 113
EDIT 2: fixed it and updated to WM6.5.5 how?
crabiorc said:
You will need the program MTTY(Attached with this post).
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
2) Phone needs to be POWER + Record + Pen Reset and on Serial/USB screen. COnnect it to the PC, and it should show USB, with the backlight remaining off.
3a) Run mtty1.42.exe
b) Select USB from first list (where COM1 is displayed. Don't press USB button). If USB (or a list item containing USB) isn't in the list, then you have't connected to the PC properly.
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
c) Click OK
3) Run following commands:
[press enter first to get USB> prompt]
USB>
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
USB>set 14 0
6. type "task 28" to get your device formatted
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
7. type "task 0" to ask your device reboot
USB>task 0
USB>
8) Exit the program, then if you have already got a rom installed then just soft reset
9)Now be back to the Usb/Serial screen and run your favourite ROM upgrade-A clean installation ( look for tutorial or just get the RUU from Chef Tony)
Click to expand...
Click to collapse
didn't work for me, at first the phone shows only 4 colored screen, when i press "mail" button, it's stuck on white screen, no sounds no nothing, any ideas? ;/