Rip Qtek 2020! At an insertion there was a failure and now shows inscription USB V 1.01, much that tried to put but all needlessly
User288 said:
Rip Qtek 2020! At an insertion there was a failure and now shows inscription USB V 1.01, much that tried to put but all needlessly[/QUOTE
believe me its not dead ]
just try to upgrade bootloader and try to upgrade again
but be sure that your sencronization cable works well
Click to expand...
Click to collapse
Related
i have Qtek 2020i i try to upgrad the phone
now the phone desplay (serial )
when i but the usb cable the phone desplay (usb)
the phone not boot now
what shoud i do to flash the phone
what is the matter ????????????
Flash again
Sounds like you have a similar issue to
http://forum.xda-developers.com/viewtopic.php?t=43400
You tried running the upgrade again, maybe with an earlier or the original ROM. Make sure you leave the device in the cradle until the end when it says to take it out and hard reset.
If your needing a ROM, look in the Alpine Upgrade forum, Pug has a post there with four version of the 162 ROM, I'm using the 3rd without issue.
I'm trying to fix my friend's MDA right now. The problem is, it's stuck on T-Mo splash screen. It can however go to tri-color screen. Can I save this MDA or should I bury it?
Any help would be appreciated
Hi!
At the tri-color screen you should be able to flash it with a new ROM. Just try it, that worked for me after a failed flash.
Cheers
djvw
rockmanneo said:
I'm trying to fix my friend's MDA right now. The problem is, it's stuck on T-Mo splash screen. It can however go to tri-color screen. Can I save this MDA or should I bury it?
Any help would be appreciated
Click to expand...
Click to collapse
I just had the same problem myself, talk about ****ting my pants.
I have a Dutch rom in my Vario and I cid unlocked it and tried installing
a US rom but the phone was dead after it.
In the tri-color screen I tried to load the new 2.26 US rom and then the latest UK rom but both failed with invalid Vendor id or something like that.
So I downloaded the NL rom from here and thnk god it loaded without a problem and the Vario is working again.
Sadly in Dutch but at least it works again, can anyone from Holland help me upgrade to the latest US rom ?.
Dave...
Dave...
Encountered some problem..
It would not connect to ActiveSync from tri-color screen. There is a 'USB' at the bottom screen when I plug in the USB cable, but I don't think the PC recognizes the device.
And the thing is my friend has never CID unlock the thing
He said he just took it overseas and never turned it off, when he got back here the phone went like this.
More help please
rockmanneo said:
Encountered some problem..
It would not connect to ActiveSync from tri-color screen. There is a 'USB' at the bottom screen when I plug in the USB cable, but I don't think the PC recognizes the device.
And the thing is my friend has never CID unlock the thing
He said he just took it overseas and never turned it off, when he got back here the phone went like this.
More help please
Click to expand...
Click to collapse
PC doesn't need to recgonize the device via activesync to flash the Rom.
Try and find your original rom.
Put the phone in the bootloader (canaryscreen aka tri-colored screen).
plug-in your usb plug.
And start the rom update utility.
Regardless of your activesync status it should start updating your mda.
This takes about 10 minutes, and will pause at some stage, don't be alarmed and don't pull the plug !!!
Good luck
the-equinoxe said:
Try and find your original rom.
Put the phone in the bootloader (canaryscreen aka tri-colored screen).
plug-in your usb plug.
And start the rom update utility.
Click to expand...
Click to collapse
Can I update using the latest ROM (2.26)? Why does it have to be original rom?
Regardless of your activesync status it should start updating your mda.
Click to expand...
Click to collapse
Even tho PC cannot detect the phone at all, rom update util still can go thru?
I will try again tonight, last night I tried, 2.26 rom update utility cannot detect the mda
Good luck
Click to expand...
Click to collapse
Thanks :wink:
rockmanneo said:
Can I update using the latest ROM (2.26)? Why does it have to be original rom?
Click to expand...
Click to collapse
It's recomended to go back to the original rom, so you can go back to the point before the problems began..
Even tho PC cannot detect the phone at all, rom update util still can go thru?
I will try again tonight, last night I tried, 2.26 rom update utility cannot detect the mda
Click to expand...
Click to collapse
In canary-screen mode the phone will have an active usb connection, ActiveSync won't detect it however, because the ActiveSync software on the phone is only started when windows-mobile is running (which doesn't occur in boot-loader).
The Rom Upgrade Utility, should be able to detect the phone.
But always make shure the battery has been charged (at least half-charged).
Several people on this forum have revived their semi-bricked phone this way.
Thanks :wink:
Click to expand...
Click to collapse
You're welcome
guys, how to install wm5 on blueangel? is it the same way as Himalaya?
...
just check the wi-ki page for Blueangel, there are steps on how to install WM5.0 on BA!!
Upgrading SX66
i started to upgrade my SX66 to the latest firmeare, USB direct to PC and in the middle, it lost connection and only shows USB V 2.07 on the display with the USB plugged in, when unplugged, it shows Serial V 2.07, does nothing with soft or hard reset. can anyone help or did i kill my unit?
Thanks,
Tom Rhoades
use mitty
use Mitty, when stuck on bootscreen
Hi
while i flashing my qtek comp was reseted.I now can't exit from bootloader.How i can unbrick my qtek ?
thanks
When you place the PDA on it's cradle what is displayed on the screen?
HexBox said:
When you place the PDA on it's cradle what is displayed on the screen?
Click to expand...
Click to collapse
usb is on display
my qtek9090 is dead
when your qtek 9090 stays in bootloadermodeand it give usb in screen when you put it in de cardle then run the update agian and it get unbriked and after the reupdate youre phome must work without problems
killer33 said:
when your qtek 9090 stays in bootloadermodeand it give usb in screen when you put it in de cardle then run the update agian and it get unbriked and after the reupdate youre phome must work without problems
Click to expand...
Click to collapse
That's right And hope this helps
After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???
kevinalmere said:
After i tried to install a new rom it stuck on 99% when i put my phone on it will only go to the bootloader... what can i do???
Click to expand...
Click to collapse
Always post the data of your your phone,to get help.
secondly you had a bad flash,perhaps your phone is CID locked. Which rom were you trying to flash ?
Now to recover,download the official carrier's rom and flash it while in bootloaders.The phone will start working again in default status,then,Read and understand the unlocking method and the flashing guide,read the stickies carefully and perform the method correctly.
cheers !
i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....
Help!!!
I have same Problem with TNE-V1.0n_4mb.exe
IPL 3.08
SPL 3.08
kevinalmere said:
i have a t-mobile vario:
ipl 1.06
sp 1.06
i removed the simlock with lockwizb and a tried to put airfawizard rom on it so now i have this tricolord screen en there is nothing i can do.. tried to update i with the original carrier rom but it says update error so in seems it can't see my phone or something but my usb is plugged in i hope i can fix this i only can see this blue green red screen it drives me crazy hope you can help me.....
Click to expand...
Click to collapse
If you can go to boot loader, most likely you will be ok. When you plug in the usb port, does the words in the screen change from serial to USB? Once it changes, then flash your official, and then CID unlock your device (this is different from SIM unlock). Then flash to the ROM you want!!
PS: Go read wiki about how to unlock and flash and understand more about your device. http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?
kevinalmere said:
The only thing it does is going to bootloader and when i plug my usb in it say usb but when i try to install my original rom from t-mobile ( a update ) it says it's looking for information on my mda but after a couple of second it's say UPDATE ERROR i use windows vista can that be a problem? and how do i know wich one is the original..?
Click to expand...
Click to collapse
Vista dont like upgrading and stuff...but there is a work around, search the forum and see if you find it. Or try using XP.
okee problem solved working again
thanks for your help!!!
kevinalmere...
How did you resolve the issue I'm having very simular problems and believe it's my Vista OS causing the problem..
Orange SPV M600 G4
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 4.0.0.0
Sorry should explain my issue incase anyone can help.
I attempted an upgrade to WM6 using an Upgrade .Bat from this site. I was slightly impatiant due to not being able to complete the downgrade first anyway the upgrade frose, after a while I canceled the update and carried out a hard re-set... Since then I'm not able to boot nor connect to my desktop via Active sync (WMDC (Vista))
I've followed every instruction I can find but only to be meet with RUU Errors saying can't connect or file open. I can however acces my Bootloader screen and when connection is made the USB symbol shows on the screen of my phone...
Any help would be greatly recieved......