Hi
while i flashing my qtek comp was reseted.I now can't exit from bootloader.How i can unbrick my qtek ?
thanks
When you place the PDA on it's cradle what is displayed on the screen?
HexBox said:
When you place the PDA on it's cradle what is displayed on the screen?
Click to expand...
Click to collapse
usb is on display
my qtek9090 is dead
when your qtek 9090 stays in bootloadermodeand it give usb in screen when you put it in de cardle then run the update agian and it get unbriked and after the reupdate youre phome must work without problems
killer33 said:
when your qtek 9090 stays in bootloadermodeand it give usb in screen when you put it in de cardle then run the update agian and it get unbriked and after the reupdate youre phome must work without problems
Click to expand...
Click to collapse
That's right And hope this helps
Related
HELP MY QTEK 9090 is totally struck when I eas upgrading I've tryed so many times BUT NOTHINGS HAPPENS!!! I'VE ALWAYS RED ERROR MESSAGE ADN ICAN'T GO BACK!!
CAN ANYBODY HELP ME PLEASE!!
THANKS
:twisted: :evil: :?: :?:
i have any problem like your, what error message you have? win ce image error or anyhink like this?? can you get to bootloader?
Topic moved to BA Upgrading etc.
Did you read this page
http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade
no i can't!!!
no I can't the pda is completly dead ti gives me the writings
SERIAL
V2.07
AND NOTHING ELSE!!!
I follow the FAQ suggestions but nothings HAPPENS!!!
HELPME PLEASE!!!!
:evil: :evil: :evil:
1)Take it out off the cradle.
2)Take the battery off, and leave it off for about 20 minuts.
3)Make sure that the USB cable is connected directly to your PC, and not through a HUB.
4)Reboot PC, dont start any programs.
5)Put the battery back on you BA, switch it on and Cradle it
6)Follow instructions in WIKI
it work only in eglish version
Thaks Bosjo but works the english version rom only!!
I've discovered , anso I thank you so much, that exist one italian version only for my qtek 9090 the other one once I've tried it
doesen' t work AGAIN!!, I : was been found the same problem...
I'will follow your suggestions...
:evil: :evil: :?:
thanks
Alexj
[please follow bosjo suggestion if u have an english versio, but I need the italian one it's a big probelm for me to install it...damn...!! :twisted:
bosjo said:
3)Make sure that the USB cable is connected directly to your PC, and through a HUB.
Click to expand...
Click to collapse
****, i made a Typo, it should say
3) Make sure that the USB cable is connected directly to your PC, and NOT through a HUB.
It should work with all the roms. (those on the 1.40 link page)
ti's all ok over there
Yeah my fried my cradle is direcly connected to my usb port...
thanks :twisted: :evil:
BAD ROM UPDATE!!
AND NOW : ERROR 102 THE ROM IMAGE FILE IS CORRUPT !!!
I'M REALLY BEACAME NERVOUS..
Any suggestion bosjo??
Please I'm struck again.. :evil: :evil: :evil:
always stuck
Hi my friend after having succes to upgrade my 9090 in english, no way that italian programs, works I've tried to install italian cab files..but. nothings happens.
then I restarted from zero and that'it..
AND NOW : ERROR 102 THE ROM IMAGE FILE IS CORRUPT !!!
and now what should I do please?? The separated files in(verion in WWE) seems not to work !!!!
I'M REALLY BEACAMING NERVOUS..
:evil: :evil: :evil:
Re: ti's all ok over there
alexj10 said:
Yeah my fried my cradle is direcly connected to my usb port...
thanks :twisted: :evil:
Click to expand...
Click to collapse
Well I am lost now.
You say that you can flash a wwe rom, if so which one.
You say you cant flash the ITA 1.40 rom but you dont tell us how you are trying to flash it.
Best is always to start form the begining.
Get your shipped rom back on the device.
Upgrade the radio .....only
empty out the ext rom....
then falsh the CE...only
and if you need help tell us what you did as it would explain how you got the error message. We have no idea what you are doing thus cant help you much.
The program I've first tried named BA_DT_ITA_14004_153_1120.ship
doesent' work !! So Ive my 9090 completly dead, I've red almost all the instructions but now I really dont'know how to move myself, and I'dont remeber the previuos version because is cancelled.the attemp to update to 1.40; 1.40.153; 1.12.00 always fails
I've tryed many times to run the program above, but the error messge is the same : soft reset and restart....
so really do not be able to
Get your shipped rom back on the device.
empty out the ext rom....
then falsh the CE...only
can u hepl me please ??
Ok lets get a wwe 1.40 on your device. (as I am not sure if the ita is Broken)
Follow :
http://wiki.xda-developers.com/index.php?pagename=BA_1.40.00_Upgrade
1) Take the IMate rom.
2) Download the rom and the MA file.
On device
1) On your device perform a Hard reset
2) Remove the battery
3) Wait 5 mins
4) Put battery in again
on PC
1) Reboot your PC after download
2) Make sure the cradel is connected to your PC with no hub.
3) Turn on device
4) Place it in cradel
Run the upgrade
chose the:
First Method (Quick/Easy) (TYPE II)
Post what happens
country error
thanks for the attempt but the message is country error ...
:evil:
country erroro
[
I've done but..
thanks but the message is :country error....
with the old method applicated at your concept the message is ROM error....and now what's up :?:
What exe are you runing : Name of that file!
file name
the file name is rom 1.13.00
but in th e italian vrsiona the name is ns and anothe rone is nk
Sorry but I'm not so expert mybe isould try the secon method downloading separate file s..??
thanks again.. :?:
There is no file name 1.13.00.exe !
I'm trying to fix my friend's MDA right now. The problem is, it's stuck on T-Mo splash screen. It can however go to tri-color screen. Can I save this MDA or should I bury it?
Any help would be appreciated
Hi!
At the tri-color screen you should be able to flash it with a new ROM. Just try it, that worked for me after a failed flash.
Cheers
djvw
rockmanneo said:
I'm trying to fix my friend's MDA right now. The problem is, it's stuck on T-Mo splash screen. It can however go to tri-color screen. Can I save this MDA or should I bury it?
Any help would be appreciated
Click to expand...
Click to collapse
I just had the same problem myself, talk about ****ting my pants.
I have a Dutch rom in my Vario and I cid unlocked it and tried installing
a US rom but the phone was dead after it.
In the tri-color screen I tried to load the new 2.26 US rom and then the latest UK rom but both failed with invalid Vendor id or something like that.
So I downloaded the NL rom from here and thnk god it loaded without a problem and the Vario is working again.
Sadly in Dutch but at least it works again, can anyone from Holland help me upgrade to the latest US rom ?.
Dave...
Dave...
Encountered some problem..
It would not connect to ActiveSync from tri-color screen. There is a 'USB' at the bottom screen when I plug in the USB cable, but I don't think the PC recognizes the device.
And the thing is my friend has never CID unlock the thing
He said he just took it overseas and never turned it off, when he got back here the phone went like this.
More help please
rockmanneo said:
Encountered some problem..
It would not connect to ActiveSync from tri-color screen. There is a 'USB' at the bottom screen when I plug in the USB cable, but I don't think the PC recognizes the device.
And the thing is my friend has never CID unlock the thing
He said he just took it overseas and never turned it off, when he got back here the phone went like this.
More help please
Click to expand...
Click to collapse
PC doesn't need to recgonize the device via activesync to flash the Rom.
Try and find your original rom.
Put the phone in the bootloader (canaryscreen aka tri-colored screen).
plug-in your usb plug.
And start the rom update utility.
Regardless of your activesync status it should start updating your mda.
This takes about 10 minutes, and will pause at some stage, don't be alarmed and don't pull the plug !!!
Good luck
the-equinoxe said:
Try and find your original rom.
Put the phone in the bootloader (canaryscreen aka tri-colored screen).
plug-in your usb plug.
And start the rom update utility.
Click to expand...
Click to collapse
Can I update using the latest ROM (2.26)? Why does it have to be original rom?
Regardless of your activesync status it should start updating your mda.
Click to expand...
Click to collapse
Even tho PC cannot detect the phone at all, rom update util still can go thru?
I will try again tonight, last night I tried, 2.26 rom update utility cannot detect the mda
Good luck
Click to expand...
Click to collapse
Thanks :wink:
rockmanneo said:
Can I update using the latest ROM (2.26)? Why does it have to be original rom?
Click to expand...
Click to collapse
It's recomended to go back to the original rom, so you can go back to the point before the problems began..
Even tho PC cannot detect the phone at all, rom update util still can go thru?
I will try again tonight, last night I tried, 2.26 rom update utility cannot detect the mda
Click to expand...
Click to collapse
In canary-screen mode the phone will have an active usb connection, ActiveSync won't detect it however, because the ActiveSync software on the phone is only started when windows-mobile is running (which doesn't occur in boot-loader).
The Rom Upgrade Utility, should be able to detect the phone.
But always make shure the battery has been charged (at least half-charged).
Several people on this forum have revived their semi-bricked phone this way.
Thanks :wink:
Click to expand...
Click to collapse
You're welcome
I downloaded a wm6 upgrade pack from Demonoid. The instructions told me that I needed to load an older rom on before I could CID unlock. The ROM was: CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE. The ROM that was originally on my 9100 was the lastest from Qtek. My Qtek now will not move on from the splash screen. Does this sound like I have a dead pda? Anyone have any idea how to get out of this problem. Any advice or comments would be appreciated.
Thanks
PS: I turned it off for the time being. Now I can't even turn the dam thing on!
I think I may have found a solution if I can just turn it on!! Won't charge either!
Well if u can get it turned on hold the voice and cam buttons and get it into bootloader you'll be good
Rip Qtek 2020! At an insertion there was a failure and now shows inscription USB V 1.01, much that tried to put but all needlessly
User288 said:
Rip Qtek 2020! At an insertion there was a failure and now shows inscription USB V 1.01, much that tried to put but all needlessly[/QUOTE
believe me its not dead ]
just try to upgrade bootloader and try to upgrade again
but be sure that your sencronization cable works well
Click to expand...
Click to collapse
Hi
i have htc touch 3g
but it WM 6.1 has damaged!
now i need your help in order to make it work and upgrade it to WM 6.5
now i have no start menu! and no file manager!
the only thing i can do is just connecting it to PC and use ActiveSync!
so help me on unlocking it and also on restoring the WM 6.5 ROM!
thanks all
what I've done until now!
i have downloaded Jade Hard SPL v41.exe and use it. it installs enablerapi on my device!
i downloaded CustomRUU.exe and use it but i get connection error on last step of update! but my phone is connected! the problem is that when i click on update my LCD goes off!
and i think it disconnects from PC!
i also downloaded Jade_V5_Com_5_23569.7z
Click to expand...
Click to collapse
please help me!
alimooghashang said:
Hi
i have htc touch 3g
but it WM 6.1 has damaged!
now i need your help in order to make it work and upgrade it to WM 6.5
now i have no start menu! and no file manager!
the only thing i can do is just connecting it to PC and use ActiveSync!
so help me on unlocking it and also on restoring the WM 6.5 ROM!
thanks all
what I've done until now!
please help me!
Click to expand...
Click to collapse
isn't there anybody helps me?
If you have done hard spl, go into rom folder (Jade_V5) and click on romupdateutility.exe and follow the steps. No need for custom ruu. exe
tropical cactus said:
If you have done hard spl, go into rom folder (Jade_V5) and click on romupdateutility.exe and follow the steps. No need for custom ruu. exe
Click to expand...
Click to collapse
when i click on update button and when it wants to start the progress, my phone lcd goes off and disconnect from the PC
what to do?
Never had that happen before. Maybe you can check your power status in settings/system. Go to advanced and see external power settings. Or you can try another rom like megade 1.7.5. You'll have to take it in to the service centre if it doesn't change.
tropical cactus said:
Never had that happen before. Maybe you can check your power status in settings/system. Go to advanced and see external power settings. Or you can try another rom like megade 1.7.5. You'll have to take it in to the service centre if it doesn't change.
Click to expand...
Click to collapse
where to download it?
ali mooghashang
agar hanooz natoonesti dorostesh koni begoo ke behet begam chikaresh koni
felan ta mogheii ke begi,.... ba ye computere dige ham test kon... tamame virus kosho fire wall haro ham off kon
hrkh83 said:
ali mooghashang
agar hanooz natoonesti dorostesh koni begoo ke behet begam chikaresh koni
felan ta mogheii ke begi,.... ba ye computere dige ham test kon... tamame virus kosho fire wall haro ham off kon
Click to expand...
Click to collapse
no it isn't
hrkh83 said:
ali mooghashang
agar hanooz natoonesti dorostesh koni begoo ke behet begam chikaresh koni
felan ta mogheii ke begi,.... ba ye computere dige ham test kon... tamame virus kosho fire wall haro ham off kon
Click to expand...
Click to collapse
hi
pls post in english only this is an English forum
alimooghashang said:
no it isn't
Click to expand...
Click to collapse
hi
try this
if u can go to ur boot loader ie the tricolor
then good connect ur phone via USB cable to pc and if see if u get the USB word on the tricolor if so very good now go to any orignal rom u have on ur pc click on it and do as the screen says
i did this long time back it worked hope it helps
if u want orginal shipped rom for ur jade go to shipped rom.com and download the same
good luck
haree said:
hi
try this
if u can go to ur boot loader ie the tricolor
then good connect ur phone via USB cable to pc and if see if u get the USB word on the tricolor if so very good now go to any orignal rom u have on ur pc click on it and do as the screen says
i did this long time back it worked hope it helps
if u want orginal shipped rom for ur jade go to shipped rom.com and download the same
good luck
Click to expand...
Click to collapse
i can't go to ur boot loader!
this is my problem!
when it wants to update the rom , the lcd goes off and disconnects from pc! and doesn't go to tri color bool loader step!
try this,
remove the cover
remove the battery
press the down volume and insert the plug into ur phone
power on the phone and see!
if the boot loader not come, then there are hardware problem in the phone, u had to visit HTC and only HTC service center.
rgrds
I thik u didnt do a hard SPL, dowload jade spl from (http://forum.xda-developers.com/attachment.php?attachmentid=220714&d=1251248001)
then run it while ur jade connected to Activsync
and try try to upgrade again