Related
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
viper2g1 said:
Please help, I was uninstalling some applications from my HTC PURE and had to restart the phone, when it was rebooting it hung at the ATT screen and there was small red text in the bottom left screen.
I had previously installed HardSPL 1.83 but relocked it via instructions in 2nd post because I'm still deciding if I wanna keep the phone and didn't wanna do anything for warrenty reasons.
I have the stock ROM and never installed anything except the HardSPL and the revert.
Please help me, I have tried to load the ATT Pure Stock/Shipped ROM I found here but everytime I try to in the bootloader mode it says either "no image file" or hangs at loading depending what I've tried to name the file. Also I've tried to run customruu.exe to install the stock ROM and also tried to install HardSPL 1.83 but it hangs at 0% and eventually wants to do recovery on the PC.
How do I fix this problem, and preferabbly get it back stock. I do have a warrenty, well unless I violated it by installing HardSPL then doing the revert.
Thanks
Click to expand...
Click to collapse
Of course you hard reset?
Make sure your SD card is formatted to Fat32 and you may mant to try a different card, 2gb - 4gb.
What does your SPL say now in bootloader mode?
Yes I tried a hard reset. I can try another sd card the one I used was fat32 and 2gb. I believe it says 1.33 can't look now but I know it's not the same as an untouched pure.
Help!
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
themasterhook2000 said:
You are not the only one who is having this issue. I am frustrated beyond frustrated. How are other people flashing their out of the box ATT Pures using the same exact steps but I can't? It's making no sense.
1. I turn off firewalls.
2. I've tried both usb and sd card boot, didnt work
3. I installed the enablerapi cab
Nothing works and I am having the same problem you are having...it stays on 0% forever and it doesnt even prompt me saying there is an error it just sits on 0% until I unplug it...
Help!
Click to expand...
Click to collapse
Are you trying to HSPL or flash a ROM?
Well
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
How to flash HSPL.
themasterhook2000 said:
According to what i've read, you have to do Hard SPL before you flash a rom, so i've been trying to HardSPL and it doesn't work! I even tried to skip the step and just flash the rom and it doesnt work..
Now, I also have an ATT Tilt to and I JUST flashed a rom 30 mins ago, so it has nothing to do with firewalls or anything as far as my computer goes, I think its the phone, so what can I do?
Click to expand...
Click to collapse
Its a good thing flashing the ROM didn't work, you'd be bricked.
For flashing HSPL, it seems that newer phones are having an issue.
Something may have been changed that is preventing the unlocker from working.
Do the following;
1. Hard Reset
Instructions:
- Soft reset with stylus
- Hold Vol up & Vol dwn simultaneously until white screen appears
- Following screen prompts, Press Vol up to confirm.
2. Go to bootloader mode.
Instructions:
- Turn off your device using the power button
- When the device is turned off, simultaneously press the Vol dwn + Power button
- Your device will startup in Bootloader mode
Should say SPL: 1.33 or something.
3. Sync your phone to your PC.
4. Install enablerapinew.cab
5. Unzip both Topaz_CustomRUU_v1.1.zip & SPL_183.zip to the same folder
6. Run the CustomRUU.exe
This process should install HSPL and now when you enter bootloader mode you should see something like SPL: 1.83 Olinex.
If so, you're ready to start flashing custom ROMs.
If not, please report all errors to the HSPL thread or PM Olipro.
**I take no responsibility for any loss of data or functionality of your device.**
See, the problem with your instructions are...
1. You cannot soft reset with the stylus, I don't see a button anywhere on the phone ( ATT PURE not Diamond 2 )
2. Holding Vol up & Vol down simultaneously until white screen appears doesn't work. The only thing that works is when I hold Vol Down and the screen with the colors come up, not a white screen.
So i'm still lost. Thanks for your help regardless. I just really want to flash a new rom so I can stop using this stupid slow ATT rom.
So basically you are messing with your Pure and don't know how to soft reset?
Remove the stylus and in the groove for the stylus is a red dot, that is the red reset button. Insert the tip of the stylus in the red dot and push. Now the Pure will soft reset.
Probably should familiarize yourself with the device before you finish turning it into a brick!
Oh wow. That is so hidden.
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
themasterhook2000 said:
On my Touch Pro 2 its right there on the side where you can see it, with words.
Anyway, Thank you very much, i'll try that.
Still, what about the Up and Down button volume button function so I can go into bootloader mode?
Click to expand...
Click to collapse
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Ok.
Bruce Inman said:
Now that you found the soft reset button.... follow my procedures.
Note- you have to hold the keys IMMEDIATELY after soft reset before the boot screen appears.
Click to expand...
Click to collapse
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
themasterhook2000 said:
Didn't work, I re-did the steps you listed 3 times over to make sure I was correct and the same results. I guess ATT has found a way to stop their phones from being unlocked.
Thank you for your help regardless.
Click to expand...
Click to collapse
You should probably post over in the HSPL thread.
You'll get more help over there. There are many others having similar issues and there may be a fix over there.
FYI, when you get to the tri colored screen, that is where it shows what SPL you have currently.
Updating rom freeze
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
drearystate said:
Hi, I don't post much if at all, normally you guys have it right on the button, this is my 3rd phone to run custom roms on but for some reason it just freezes on the "Updating ROM image on your PDA Phone..." screen and doesn't continue past, on my last 2 phones active sync worked well with updating to custom roms,seems like my Pure produces the same error after the attempt, its a communication error "ERROR [262] : UPDATE ERROR", now recovering from the error is not a issue, we all have familiarity in that area but I was wondering if it could be something as simple as the cable that was sent with my phone or if its possible to flash rom through sd card as opposed to using active sync?
Click to expand...
Click to collapse
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Bruce Inman said:
Yes, you can flash through storage card, just rename the .nbh to TOPAIMG.nbh, Put in root of storage card and enter bootloader mode.
You have HSPL'd, right?
Click to expand...
Click to collapse
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
arun.ramachandra said:
I was just going through the thread. I have the same issue. i have place topaimg.nbh in the root of storage card and entered bootloade mode, it shows loading and is stuck at 0%.
HSPL is 1.83. Went through entire thread of HSPL but unfortunately didn't find any solution.
Click to expand...
Click to collapse
Just to confirm, you have to name it exactly "TOPAIMG.nbh".
With all of the people that have tried all methods and still can't flash, something must have changed in the stock SPL.
Hello people
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
same problems here
i have same problem with pure to.
coldun187 said:
Hello, did anybody found the way to flash HTC PURE , I have the same problem 0%
Thanks
Click to expand...
Click to collapse
From HTC site (HTC Pure support):
What is a Soft Reset and how is it performed?
A soft reset basically resets the memory structure in the handheld. This recovers the device from memory conflicts, corrupted system service chains (mainly due to attempting hacks), memory leaks, and system lockups due to the “Fatal Exception” program errors. Removing the battery from the device while it is still powered on is NOT a soft reset and can actually damage the device.
A Soft Reset is performed by:
Remove the Battery cover and the Stylus from the device.
Insert the tip of the stylus into the Reset hole located at the entry point of the stylus silo.
The device will reboot.
I dont know whether i have asked a dumb question or not but i've searched for all the forum, it's all "discussing" and too much scattered thing that i still cant see the specified way for my phone.
Yes, again this question, I tried to flash Energy Rom on my phone, by USB and by SD card, everytime i reboot or turn off my phone, i will need to connect through USB to boot on, or not it will display tri-color screen and flash No Image File. I copied the image file to SD card and now when i boot the phone it tell me to update the rom on SD card... And if i delete this image on my SDｃａｒｄ then...it's again, nothing too much to say...
Is there any way to let my phone boot on without USB wired and no tri-color screen (i guess i hate that much).
Hope getting help from you all, and please tell me step by step, i'm newbie anyway, please.
By the way, anything related to mtty or HardSPL, SoftSPL i still dont work it out. Please give me some tips.
xgenvn said:
I dont know whether i have asked a dumb question or not but i've searched for all the forum, it's all "discussing" and too much scattered thing that i still cant see the specified way for my phone.
Yes, again this question, I tried to flash Energy Rom on my phone, by USB and by SD card, everytime i reboot or turn off my phone, i will need to connect through USB to boot on, or not it will display tri-color screen and flash No Image File. I copied the image file to SD card and now when i boot the phone it tell me to update the rom on SD card... And if i delete this image on my SDｃａｒｄ then...it's again, nothing too much to say...
Is there any way to let my phone boot on without USB wired and no tri-color screen (i guess i hate that much).
Hope getting help from you all, and please tell me step by step, i'm newbie anyway, please.
By the way, anything related to mtty or HardSPL, SoftSPL i still dont work it out. Please give me some tips.
Click to expand...
Click to collapse
Firstly, you have not written what happens to you very clearly...its is all very confusin..from what i understand, your phone boots only if you connect it to the PC via USB...With WHAT METHOD did u FLASH your phone for the FIRST time??
Im also no expert, but i wil make an attempt...what is ur current status...does your phone start at all??
circleofomega said:
Firstly, you have not written what happens to you very clearly...its is all very confusin..from what i understand, your phone boots only if you connect it to the PC via USB...With WHAT METHOD did u FLASH your phone for the FIRST time??
Im also no expert, but i wil make an attempt...what is ur current status...does your phone start at all??
Click to expand...
Click to collapse
As i pay attention to the bootloader, i'm sure that it's already made the HardSPL and the phone can recognize the image on the SD Card or by USB method. The first ROM was flash on the phone is not me, this is my friend's phone, I'm just trying to help him around then.
I tried to flash the rom by USB method, but when i restarted the phone without the USB connected to PC, it did show the bootloader (i just touch the power button, not volumn button or any other key)~ then i plug USB which connect the phone to pc, soft reset it and it boot to the system again.
I try to flash it by SD-card method but it still the same. I mean that the phone can be flashed new ROM, but it's just keeping get into the bootloader everytime i restart the phone
If the image is on the SD Card it'll tell me to upgrade ROM, if the image is not on the SD Card then "No Image File!" was flashed on~
Any ideas? My friend tells me that this happened when he tried to install Sogou - chinese input application. Is there any conflicted that cause this matter?
for little detail, the phone always shows up Successfully, but it still enter the bootloader mode at next restart. Is my flash-job done or just a mistake one?
additionally, this may be bad... remove the battery doesnt work. Please help.
help me please, do i have to hardspl again? I still cant enter WM unless i have a usb wire connected phone to pc and softreset it. Any idea?
xgenvn said:
help me please, do i have to hardspl again? I still cant enter WM unless i have a usb wire connected phone to pc and softreset it. Any idea?
Click to expand...
Click to collapse
hm, since you said the first flashed job was not yours, i think it's better that you repeat the whole procedures again starting from hardspl. but make sure you're using the correct version. re-download again if you're not sure.
also while most people rarely done so, it's bad to have multiple rom image exist in any root folder in your phone, storage card and your pc flashing tool folder (.nbh, .rom, etc), but sometimes people do forget or **** just happens.
I recommend that you remove both sim & microsd card before going any further.
then try to boot into wm with usb cable connected like you said.
take a quick look at folder and file structure in the rom. from here i would do it slightly different than others, with no battery pulls, just using the reset button. (imho, every battery pull may cause unforeseen damage especially with power still running.)
a. push hard reset combo button (don't let go) and push reset for a few secs to hard reset.
b. after hard reset rebooting the phone, push bootloader/rom update combo buttons and hit reset for a few sec. remember to keep pushing those buttons while you release the reset pin.
c. reflash hardspl, repeat step b, reflash rom. allow rom to finish doing its job. some rom may go to sleep while installing/customizing, don't let that happend.
d. just do random thing like play a game or whatever for a few minutes or more. then soft reset or power down.
e. turn on phone and wait, if problem's solved. if it is, hard reset again. continue as usual. if it's not, try other rom (ask people for md5 checksum, compare with your download). if none works, find more help.
D-jack said:
hm, since you said the first flashed job was not yours, i think it's better that you repeat the whole procedures again starting from hardspl. but make sure you're using the correct version. re-download again if you're not sure.
also while most people rarely done so, it's bad to have multiple rom image exist in any root folder in your phone, storage card and your pc flashing tool folder (.nbh, .rom, etc), but sometimes people do forget or **** just happens.
I recommend that you remove both sim & microsd card before going any further.
then try to boot into wm with usb cable connected like you said.
take a quick look at folder and file structure in the rom. from here i would do it slightly different than others, with no battery pulls, just using the reset button. (imho, every battery pull may cause unforeseen damage especially with power still running.)
a. push hard reset combo button (don't let go) and push reset for a few secs to hard reset.
b. after hard reset rebooting the phone, push bootloader/rom update combo buttons and hit reset for a few sec. remember to keep pushing those buttons while you release the reset pin.
c. reflash hardspl, repeat step b, reflash rom. allow rom to finish doing its job. some rom may go to sleep while installing/customizing, don't let that happend.
d. just do random thing like play a game or whatever for a few minutes or more. then soft reset or power down.
e. turn on phone and wait, if problem's solved. if it is, hard reset again. continue as usual. if it's not, try other rom (ask people for md5 checksum, compare with your download). if none works, find more help.
Click to expand...
Click to collapse
I've just tried out the task29, it's done normally, then flash the new rom.
1. I dont think the rom are buggy, because i changed between 2 roms and it's the same matter.
2. I dont need to use bootloader/rom update combo button because it's directly entered whenever i turn on the phone (without connected to pc) (i really really dont know why)
3. Hard reset and i have my WM work again but it's still the romupdate at boot time.
I wonder if jumpSPL did all this problems, I tried mtty by task 0 and set 14 0 but it wont restart the phone, tried to format the ROM by mtty (task 32) but it wont weep out, errors given: bad... at address...
Why does it always want me to update the ROM? Is there anything wrong with jumpSPL?
the problem still, please help me give a look to this.
ouch, last time I use mttty were ancient wm2003 era. i'll try to look for info, but can't promised anything.
at this point it's recommended to reflash the complete original stock rom, undo hardspl.
check the hardspl thread about restoring to factory default. best luck to you.
so...i've got something that xda nor google seems to have an answer for
I'm having a problem similar to other people that i've searched but my options seem to be much more limited
i'm trying to do a hard reset on my phone...start anew, re-flash, root, etc
when i go to my phone settings...and tap on "privacy", factory data reset...then "reset phone"..i get the "erase everything" screen
here's the problem..tapping on erase everything DOES NOTHING...it just blinks yellow to acknowledge that i tapped it...but it does not reset..it doesn't do anything
it doesn't freeze... (i can back out and use my phone as i normally would, etc)..but the erase everything button just doesn't do anything
i've also tried the hard reset through recovery...i get the "E:Error in CACHE:recovery/log
(No space left on device)" errors...
so i can't boot into ANY Recovery
i do have terminal installed on the phone...but i can't install any apk's (package is invalid error)
if anyone can help me, i'd be insanely grateful...thank you.
truthlesshero said:
so...i've got something that xda nor google seems to have an answer for
I'm having a problem similar to other people that i've searched but my options seem to be much more limited
i'm trying to do a hard reset on my phone...start anew, re-flash, root, etc
when i go to my phone settings...and tap on "privacy", factory data reset...then "reset phone"..i get the "erase everything" screen
here's the problem..tapping on erase everything DOES NOTHING...it just blinks yellow to acknowledge that i tapped it...but it does not reset..it doesn't do anything
it doesn't freeze... (i can back out and use my phone as i normally would, etc)..but the erase everything button just doesn't do anything
i've also tried the hard reset through recovery...i get the "E:Error in CACHE:recovery/log
(No space left on device)" errors...
so i can't boot into ANY Recovery
i do have terminal installed on the phone...but i can't install any apk's (package is invalid error)
if anyone can help me, i'd be insanely grateful...thank you.
Click to expand...
Click to collapse
First off do you have a Droid or a Milestone?
Second Have you tried flashing a stock .sbf file using RSD Lite
I have a milestone and yes i tried using rsd lite..
I did end up getting it to work...I had to take the sd card and the battery out....left the card out put the battery back in and it would work in recovery mode (although, i had to reboot it twice for it to stay in recovery mode) then the factory reset worked...
so i just need to get all my stuff back up to date and i'm ready to go...thanks though
Hi all,
I had a password lock (that appears when the phone is started and you can't go past this lock without out password) activated on my htc viva, that I forgot. Now I want to hard reset my viva. Since I am unable to go any further, I can't use "clear storage" option. And the procedure to Hard Reset is NOT working, although I am doing the Hard Reset procedure correctly. Any help to would be more than appreciated!!! Thanks
Try to reset your phone use stylus then push red button remove battery cover then hold answer and end call then you will see how to hard reset the phone. Hope that will work.
Thanks for your advice, but I have already tried to Hard Reset the device a number of times but it seems it simply ignores it. Anyway to bypass the password screen?
it seems u need to flash a rom of ur choice from SD card. u need to rename the .nbh file to OPALIMG.nbh. try this http://forum.xda-developers.com/showthread.php?t=541289.
enjoy
I have a Blu R1 HD that I have been on again off again fiddling with for a few months that is soft bricked. It will turn on but it will hang on the second "Bold like us" splash screen after the animation ends. It had no recovery installed to it prior to the bricking, I have attempted flashing a stock rom to it with SPFT but It gets interrupted less then 3 seconds in. From my reading It seems like I have the 6.6 preloader that stopped spft from working.
Is there anything that could be done with this to get it working once again?
kamikazisolly said:
I have a Blu R1 HD that I have been on again off again fiddling with for a few months that is soft bricked. It will turn on but it will hang on the second "Bold like us" splash screen after the animation ends. It had no recovery installed to it prior to the bricking, I have attempted flashing a stock rom to it with SPFT but It gets interrupted less then 3 seconds in. From my reading It seems like I have the 6.6 preloader that stopped spft from working.
Is there anything that could be done with this to get it working once again?
Click to expand...
Click to collapse
Depends on few things.
Do you know what was last thing done before this brick?
Have you tried holding volume up when powering on, to enter recovery(stock, i know you mentioned no custom recovery installed)?
It goes to and past the animation , so i don't think it is a secure boot type of failure. But maybe a bad data problem. See above statement about recovery.
mrmazak said:
Depends on few things.
Do you know what was last thing done before this brick?
Have you tried holding volume up when powering on, to enter recovery(stock, i know you mentioned no custom recovery installed)?
It goes to and past the animation , so i don't think it is a secure boot type of failure. But maybe a bad data problem. See above statement about recovery.
Click to expand...
Click to collapse
I have gone into the stock recovery menu, And i have attempted factory data reset, clearing the cache, and a root integrity check. The integrity check says one item fails the check and that is "/system/lib/libLLVM.so"
The last thing that I recall happening is that I had a pop up saying that an app had stopped working, But it reappeared immediately after closing it again several times. I thought rebooting it would stop whatever was happening, but it never came back to the OS.
The device has a small crack on the bottom right hand side of the screen that happened when it fell from my pocket on top of a ladder. A family member who also works with electronics as a hobby thinks that may have something to do with it but the phone worked for weeks after the break happened.
kamikazisolly said:
I have gone into the stock recovery menu, And i have attempted factory data reset, clearing the cache, and a root integrity check. The integrity check says one item fails the check and that is "/system/lib/libLLVM.so"
The last thing that I recall happening is that I had a pop up saying that an app had stopped working, But it reappeared immediately after closing it again several times. I thought rebooting it would stop whatever was happening, but it never came back to the OS.
The device has a small crack on the bottom right hand side of the screen that happened when it fell from my pocket on top of a ladder. A family member who also works with electronics as a hobby thinks that may have something to do with it but the phone worked for weeks after the break happened.
Click to expand...
Click to collapse
I do not know if there will be any way forward with this.
As you are not bootloader unlocked, sp flash refuses to connect, and only thing that can be done on stock is "factory reset" did not help, you might be done , other that see if can send to Blu.
mrmazak said:
I do not know if there will be any way forward with this.
As you are not bootloader unlocked, sp flash refuses to connect, and only thing that can be done on stock is "factory reset" did not help, you might be done , other that see if can send to Blu.
Click to expand...
Click to collapse
Sending to blu isnt an option. Out of waranty period, And I also opened it to make sure there was nothing obviously physically wrong.
I also tried using the dirty cow tool, But i cant seem to see the device in ADB. Fast boot however, can see it.
Update over ADB/SD in the stock recovery wouldn't lead me anywhere would they?