Database Develop

Splash screen freezing -> SOLUTION !!! DIY

Damn... I walked around and around and solution was all near me and able to do it myself...
Ok here´s how I done it.
First, I must explain what was the problem.
After update the firmware (not actually upgrade, I had the phone full of trash, so I decided to reflash same firmware v2.18 PTG), the Qtek 9100 / HTC Wizard freezed at 2nd splash screen (the one that shows OS versions IPL version, ect). Tried many different versions, upgraded to 2.24, 2.25, downgraded even to 1.6.7.3, but always same problem, freezed on second splash screen. I read many topics on xda-dev, and seen some people with same problem. Apparently there was 2 solutions. 1- send phone back to warranty. 2- write backup ROM from SD in bootloader.
Passed more then 15 hours asking for this SD backup everywhere, and COULDN´T find any help. Apparently no one had this "SD dump ROM Backup".
So here´s how I solved my problem
1- I tought that a SD backup was needed, and yes it is. But u can use your own phone and your own SD to do it.
2- Get a clean SD card (in qtek 9100 / Htc Wizard case is MiniSD) with 128MB (some people say 64MB, but I personally used a 128MB, maybe a 64MB is enough)
3- Kill (task manager) wescomm.exe (this is related with activesync installed on your PC). Insert the blank SD card on the phone.
4- Get your phone in bootloader mode. Like this : Phone powered off, press Camera button + Power On, will enter in bootloader mode (RGB screen).
5- Now connect your USB cable to your phone. And start MTTY_updateROM.exe (http://wiki.xda-developers.com/uploads/romupdate.rar). After open, on Port selection, choose \\.\WCEUSBSH001 and press OK. A window will open with a blank sheet.
6- Type "r2sd all" and hit enter... wait to the end (at end shows "cmd>"). On your phone screen u can follow backup progress... small bar will appear down the RGB screen.
7- Power off the phone (or remove battery), enter bootloader mode (camera button + power on) and this time RGB won´t appear right away. Will ask if u want to "download SD image", press voice dial button to agree, and writting will begin. Wait to the end. Power off and power on normally. Now your phone should be working ok. Not even needed to reflash the phone after this.
Thanks to all and hope this helps more people with this problem

I can get the MDA in a bootloader mode with the RGB screen but I can't figure out how to get the SD Image Boot. When I open updateROM, it only gives me the seletion of COM1 and COM3. I can't gete any farther, help plz. i really want to use my MDA
Adam

Adam, you missed a step
Kill wescomm.exe as described in step 3 and you will be able to access via USB.
3- Kill (task manager) wescomm.exe (this is related with activesync installed on your PC). Insert the blank SD card on the phone.

not work with me; so sad what i can do?
I did all yr step till n7 but after i roobot same problems;it frozeen on the page where show IPL SPL GSM OL;
ANY SUGGESTION?please help me

@nnnike i had the same problem as you did. ( getting stuck at the first splash screen) i jsut tryed this right now and greatly enough it did work !!! give it another shot it migh twork with you
i actually used my 2gig mini SD it wasnt clean ither
thank you so much for posting this Drug_Store. and for whoever worked on this. u guys are awsome

I did exactly what you do, but
Ive got message from Multi port tty:
r2sd all
***** user area size = 0x3BA00000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
You didn't get the proper security level to download a specific image
Cmd>
So, what is the next step? And did I doing something wrong?

You didn't get the proper security level to download a specific image
Cmd>
So said:
i also got the same error
Click to expand...
Click to collapse

CID unlock?
I believe that your phones aren't CID unlocked.
I think that only CID unlocked phones or inputing the BOOTLOADER password will allow to backup wizard to SD card

I've got the exact same problem, phone freezes at splash screen. Now I backed up a rom from a working cid-unlocked wizard, but after I tried loading it on my wizard it says 'don't allow update'. So what can I do now?

Awesome solution! My MDA vario is back from the dead!
Thank you for sharing this great solution with us

Thanks my phone is back!, now how can I get to use tha card again? I dont have a card reader for my pc, just the phone. Is ther something that I can use, because my device dont get any storage Card.

Rafase282 said:
Thanks my phone is back!, now how can I get to use tha card again? I dont have a card reader for my pc, just the phone. Is ther something that I can use, because my device dont get any storage Card.
Click to expand...
Click to collapse
I was forced to buy a multi-card reader to get my card back Fortunately that they are so cheap these days (less than 12€ for 31 diff cards)
Funny thing is that after formatting the card in Win2k the phone still asks if i wish to restore image when entering bootloader mode
cheers

hi
did you slove this your problem ?
i also got the same error

It stoppped asking to restore image when entering bootloader mode maybe because i've been using the card in normal PPC operations and the "r2sdall" area must have been overwritten

Yes, data remain at SD card. Probably need to insert in SD card reader and format under windows system.
About the errors while reading the data to SD, I remind, to try in a fully clean SD card (formatted completly), and yes, might require that your phone be CID unlocked, but that part can also be done easily.
The data that is written on the SD will remain hidden, and are like system files. That´s why no one can share the needed files over the internet or download somewhere. Because can´t get the files out of there. However, if u seen in your file explorer in your phone some file might appear on card root. But also not sure if can copy it from there and later apply on a card and do this procedure.

tjmvdz said:
I've got the exact same problem, phone freezes at splash screen. Now I backed up a rom from a working cid-unlocked wizard, but after I tried loading it on my wizard it says 'don't allow update'. So what can I do now?
Click to expand...
Click to collapse
Hello I think there is no way to restore a Sd backup on CID locked device.
I think the only possibility is to unlock CID with Imeicheck site (the process begin in bootloader mode) and then restore Sd image.

fla242;1114868
I think the only possibility is to unlock CID with Imeicheck site (the process begin in bootloader mode) and then restore Sd image.[/QUOTE said:
How it can be made?
Click to expand...
Click to collapse

Thanks a TON for the help. I went on with a little diff solution. Went upto step 4 and got the bootloader and then installed the new update from O2 and it worked.
(The step 5-7 somehow didn't work for me so I did this and it worked.)

hi all
i got problem to unlock cid on bootloader (other than imei check site)...
please help.
thanx

Hi i have a mda vario 1 ipl and spl 1.06 i have got it unlocked whit a code thad i have got from t-mobile but this don't work for me i get the message: ***** user area size = 0x3CA0000 Bytes
R2SDBackup() - Download type = 5
usTotalBlock = 1 sizeof(SDCARD_SIGNATRUE_TABLE)=512
You didn't get the proper security level to download a specific image
what can be the problem can anybody help me

New HTC Trinity issues

Got my Trinity in the mail today and started the process of pimping it up to xda-developers' standards.
1. Ran SSPL-TRIN.exe without problems from "HTC Trinity SIM & CID Unlock - v1")
2. Ran ROMUpdateUtility.exe. Dialog on PC said upgrade was successful, but screen was black on device
3. Soft reset device. Windows Mobile (green screen) shows, but never goes away. Repeated this procedure 3 times (waited over 5 min each time)
4. Hard reset device. HTC logo shows with numbers "M 05, B 05, D 1.16" showing for 5 seconds. The text "No GSM" appears for 1 second and disappears with the numbers. Only the HTC logo on white is on the screen, forever.
Any ideas? Would hate to have bricked my phone after only a couple of hours.

I can get into the three color screen. I attempted to run ROMUpdateUtility, as I wrote before, again, but I get an error message on the PC saying that the ROM is corrupted, after which my device resets. (To HTC screen, forever, like I wrote above)

Sounds like a bricked device already.
There is a lot of information on this problem in the Hermes Wiki and forum. You may find some useful information there to help unbrick.
Sorry mate.
S.K.

Is there a way I can obtain a rom that will be accepted by my bootloader? I checked on the FTP, but there's nothing there (anymore?)
If so, perhaps I could flash over to a standard one, then start over.

lazaron said:
Is there a way I can obtain a rom that will be accepted by my bootloader? I checked on the FTP, but there's nothing there (anymore?)
If so, perhaps I could flash over to a standard one, then start over.
Click to expand...
Click to collapse
Check the Wiki, you will find links to some standard ROMs.

lazaron said:
Is there a way I can obtain a rom that will be accepted by my bootloader? I checked on the FTP, but there's nothing there (anymore?)
If so, perhaps I could flash over to a standard one, then start over.
Click to expand...
Click to collapse
Chek here:
http://wiki.xda-developers.com/index.php?pagename=Trinity_Upgrades

Will try them all now. Results with all roms thus far have been:
Progress bar on both PC and phone moves to 1%, then:
a) Phone reboots & PC displays error "invalid vender ID" or b) Phone reboots & PC displays error about image being corrupt

Good news!
I went to a HTC service center where I live (Oslo, Norway). They said they could fix it in 15 min. (flash the device with an original ROM using more advanced equipment than a USB cable)
After about 10 min. the guy comes back with the phone, which now has the exact same screen I was stuck on and concludes that the motherboard is broken. I told them how I had only owned the phone for a day and they offered to replace the motherboard for free (took a few hours).
Once I got back home with the repaired phone, I was pretty nervous about flashing it again, but everything went perfectly.

Congrats friend... let me tell you that you got balls to re-flash your new device after the repair .

lazaron said:
...
2. Ran ROMUpdateUtility.exe...
Click to expand...
Click to collapse
Can you tell us exactly what ROM you used to update and is your Trinity HTC made ?

Always flash from the SD card!
Cr7pt0r said:
Congrats friend... let me tell you that you got balls to re-flash your new device after the repair .
Click to expand...
Click to collapse
Actually, I'd suggest adding to the Wiki that any flash should always be done directly from the SD card (as per instructions in the wiki) to avoid PC/USB problems. After bricking my Hermes because of a USB comm problem, I always flash from the card directly. Much faster and safer.
/politby

Upgrading and Unbranding Treo 750

With this method I have successfully unbranded, unlocked, and updated 2 Treo 750s that were originally AT&T/Cingular branded.
I spent hours running through multiple threads reading and searching to finally find a solution that worked flawlessly. These steps have been compiled from multiple threads:
http://forum.xda-developers.com/showthread.php?t=428048
http://forum.xda-developers.com/showthread.php?t=412999
http://forum.xda-developers.com/showthread.php?t=334100
Big thanks to Olipro, konker, and jcrompton!!!
Download the following:
Magic Unlocker from http://forum.xda-developers.com/showpost.php?p=2468221&postcount=2
CheetahUnlocker from http://forum.xda-developers.com/showpost.php?p=1556568&postcount=1
1_CHEE_MountExtROM.cab and 2_Chee_Extrom_rename.cab from http://forum.xda-developers.com/showpost.php?p=1424566&postcount=374
Treo750_OS5_2_19199WWE_STD.rar from http://omnifusionhosting.net/treo750/
(I couldn't find the original posts for Treo750_OS5_2_19199WWE_STD.rar so I uploaded to my own site for now)
1. Download, extract, and run MAGIC_UNLOCKER on your phone.
2. Select both options in MAGIC_UNLOCKER and click unlock. This will unlock your phone.
3. Format your SD card to FAT32.
4. Extract Treo750_OS5_2_19199WWE_STD.rar and copy/paste CHEEIMG.nbh to the formatted SD card.
5. Transfer 1_CHEE_MountExtROM.cab and 2_Chee_Extrom_rename.cab to your Treo 750.
5. Run/Install 1_CHEE_MountExtROM.cab and then soft reset the phone.
7. Run/Install 2_Chee_Extrom_rename.cab and then soft reset the phone.
8. Click and run Start>Programs>Chee_Extrom_Unlocker. Run it about 3 or 4 time and you should some type of error messages. Just OK or X them and soft reset the phone again.
9. Open File Explorer and click the drop down arrow, in which you will now see ExtendROM. Open it and delete the 2 files in the partition folder.
10. Download, extract, and run CheetahUnlocker on your computer. For this part make sure you have an ActiveSync (XP) or WMDC (Vista) connection to your phone. Click Flash SPL and go through the steps for CheetahUnlocker to Flash SPL. Don't worry about any of the other items in the menu.
11. After going through the steps in CheetahUnlocker and the phone, the phone will enter into tri-color bootloader screen momentarily followed by Loading screen...
12. Next, you'll see a light blue screen with the heading CHEEIMG.nhb followed by a few other entries below it. At this point, it will tell you press the power button. Go ahead and press the End Call/Power button. This will begin the ROM flashing. The ROM flashing takes about 5 to 15 minutes.
13. When the flashing is completed, the bottom of the screen will say Update successful and the entries above with the OK seen at the end. Now reset the Treo 750 with the stylus and immediately (during the Palm Logo) perform a Hard Reset. This is accomplished by pressing and holding the End Call/Power button and simultaneously resetting the Treo 750.
14. You will now be prompted to Erase All Data. Press the Up key of the D-Pad to continue and erase the data. This will format the phone.
11. Upon completion, the Treo 750 will continue to boot-up and go through the initial start-up steps and wizard. Once completed, your phone will now be unlocked, unbranded, and updated to Windows Mobile 6.1.
I made this thread to help people unbrand, unlock, and update their Treo 750s without having to waste hours looking for solutions and how-to something. Basically, made it easier for the noobies and everyone else to find everything in one thread.

Hey man Thanks a lot for the noob hand book
I'll try this but i dont know if it's works for me. if you can let me know thanks..
my treo 750
treo750-2.25-att
1.54.27.00

It should work on all Treo 750s!
Just make sure you are not running WM5 on it and its already upgraded to WM6.
It looks like yours already is WM6 from the 2.25.
SO you should be good!

Thanks for the info
I had a Dash, which I upgraded to 6.1 and it was great. Now I have a Treo and have unlocked it but am not sure how to format the SD stick. I must admit to being spoiled using 6.1 and being able to recognize the SD as a separate USB drive. Is there a way to do that with the AT&T version of 6.0? I am not seeing how to format the disk from the phone. Any ideas?

There are many programs you can find to format your SD card to FAT32. Just look around on XDA and you'll find some posts about it.
I just stuck into my computer and did a quick format to FAT32.

Finally a tutorial for this process that I could follow. The other night, I flashed my treo 750 to WM6.1. It didn't go smoothly for me however, and I had to do it a number of times before it "took". After each of the first 2 failures, I had to reflash back to WM6, and start over. I did nothing different, it just finally took. During one of my failures, it even booted WM6.1, but locked up and failed during the initial regional setting phase. It would help if the following section of the instructions were clearer:
12. Next, you'll see a light blue screen with the heading CHEEIMG.nhb followed by a few other entries below it. (WHAT ENTRIES?)
13. When the flashing is completed, the bottom of the screen will say Update successful and the entries above with the OK seen at the end. Now reset the Treo 750 with the stylus and immediately (during the Palm Logo) perform a Hard Reset. This is accomplished by pressing and holding the End Call/Power button and simultaneously resetting the Treo 750. (WHY NOT HARD RESET DIRECTLY AFTER "Update successful"?)

mtiberio said:
12. Next, you'll see a light blue screen with the heading CHEEIMG.nhb followed by a few other entries below it. (WHAT ENTRIES?)
Click to expand...
Click to collapse
I can't recall exactly what those entries were but it didn't really matter what the entries.
mtiberio said:
13. When the flashing is completed, the bottom of the screen will say Update successful and the entries above with the OK seen at the end. Now reset the Treo 750 with the stylus and immediately (during the Palm Logo) perform a Hard Reset. This is accomplished by pressing and holding the End Call/Power button and simultaneously resetting the Treo 750. (WHY NOT HARD RESET DIRECTLY AFTER "Update successful"?)
Click to expand...
Click to collapse
I guess you could hard reset there but like i said in my post, i compiled the directions from various threads and that's what they said to do.
Were you able to unlock, unbrand, and upgrade the Treo eventually?

Thanks dubLeE so much for the detailed steps.. Here are my comments:
2. Select both options in MAGIC_UNLOCKER and click unlock. This will unlock your phone.
I didn’t do this step since I got my treo 750 originally unlocked.
3. Format your SD card to FAT32.
Succeeded.
4. Extract Treo750_OS5_2_19199WWE_STD.rar and copy/paste CHEEIMG.nbh to the formatted SD card.
Succeeded.
5. Transfer 1_CHEE_MountExtROM.cab and 2_Chee_Extrom_rename.cab to your Treo 750.
Succeeded.
5. Run/Install 1_CHEE_MountExtROM.cab and then soft reset the phone.
Succeeded.
7. Run/Install 2_Chee_Extrom_rename.cab and then soft reset the phone.
Succeeded.
8. Click and run Start>Programs>Chee_Extrom_Unlocker. Run it about 3 or 4 time and you should some type of error messages. Just OK or X them and soft reset the phone again.
OK, what I did is the following. I clicked on the program 3 to 4 times.. Each time I get an error but I ignore, finally I did one soft reset.
9. Open File Explorer and click the drop down arrow, in which you will now see ExtendROM. Open it and delete the 2 files in the partition folder.
The two files are found and deleted successfully.
10. Download, extract, and run CheetahUnlocker on your computer. For this part make sure you have an ActiveSync (XP) or WMDC (Vista) connection to your phone. Click Flash SPL and go through the steps for CheetahUnlocker to Flash SPL. Don't worry about any of the other items in the menu.
Mmm this step faild so I couldn’t complete to the next step!!!!
My Treo restart to the colored screen and then I get a gray screen with a counter on the top left. The counter start until it reach %7 then suddenly the device restart and I get a black screen which I have to restore my previous WM6 original ROM… ok, I personally believe I have to upgrade my SPL… this is my current configuration
CE OS 5.2.1239 (Build 17746.0.2.4)
Software Version:
TREO750-1.16-RWE
Hardware Version:
A
Farmware Version:
1.12.0c.00
On the colored screen I get the following:
Palm Tr
IPL-0.20
Palm Tr
SPL-0.24.0000
Waiting for your advice….

Hey hammod2k, try running magic_unlocker and see if it make any difference.
If not, then do a hard reset on the phone and go through ALL of the steps again. I read somewhere on the forum that some people were having problems and a hard reset first helped unlock and install WM 6.1.

Thanks for your fast reply. I will try it and i will let you know

hammod2k said:
Thanks dubLeE so much for the detailed steps.. Here are my comments:
2. Select both options in MAGIC_UNLOCKER and click unlock. This will unlock your phone.
I didn’t do this step since I got my treo 750 originally unlocked.
3. Format your SD card to FAT32.
Succeeded.
4. Extract Treo750_OS5_2_19199WWE_STD.rar and copy/paste CHEEIMG.nbh to the formatted SD card.
Succeeded.
5. Transfer 1_CHEE_MountExtROM.cab and 2_Chee_Extrom_rename.cab to your Treo 750.
Succeeded.
5. Run/Install 1_CHEE_MountExtROM.cab and then soft reset the phone.
Succeeded.
7. Run/Install 2_Chee_Extrom_rename.cab and then soft reset the phone.
Succeeded.
8. Click and run Start>Programs>Chee_Extrom_Unlocker. Run it about 3 or 4 time and you should some type of error messages. Just OK or X them and soft reset the phone again.
OK, what I did is the following. I clicked on the program 3 to 4 times.. Each time I get an error but I ignore, finally I did one soft reset.
9. Open File Explorer and click the drop down arrow, in which you will now see ExtendROM. Open it and delete the 2 files in the partition folder.
The two files are found and deleted successfully.
10. Download, extract, and run CheetahUnlocker on your computer. For this part make sure you have an ActiveSync (XP) or WMDC (Vista) connection to your phone. Click Flash SPL and go through the steps for CheetahUnlocker to Flash SPL. Don't worry about any of the other items in the menu.
Mmm this step faild so I couldn’t complete to the next step!!!!
My Treo restart to the colored screen and then I get a gray screen with a counter on the top left. The counter start until it reach %7 then suddenly the device restart and I get a black screen which I have to restore my previous WM6 original ROM… ok, I personally believe I have to upgrade my SPL… this is my current configuration
CE OS 5.2.1239 (Build 17746.0.2.4)
Software Version:
TREO750-1.16-RWE
Hardware Version:
A
Farmware Version:
1.12.0c.00
On the colored screen I get the following:
Palm Tr
IPL-0.20
Palm Tr
SPL-0.24.0000
Waiting for your advice….
Click to expand...
Click to collapse
I followed all the instructions and got to the same thing as you. Now I have a black screen and not sure what to do now as I am not able to soft/hard reset the treo anymore?
What do I do to get out of this black screen and upgrade and unlock my treo?

hammod2k said:
Thanks dubLeE so much for the detailed steps.. Here are my comments:
My Treo restart to the colored screen and then I get a gray screen with a counter on the top left. The counter start until it reach %7 then suddenly the device restart and I get a black screen which I have to restore my previous WM6 original ROM…
Click to expand...
Click to collapse
I cannot get out of this black screen now?
It wont even sync with Active Sync anymore for me to do anything....PLS HELP!!
How can I restore my Treo 750 back and unlock it?

Ok, After longs hours on the computer, I found a way to fix it and load back up the ROM.
I have also been able to do all your steps line by line with success. I have been able to upgrade to W6.1 but my treo 750 is NOT YET UNLOCKED!!!!
I have done it twice. line by line, number by number and step by step. All with ease but still not unlocked.
Can someone tell me how to unlock it now?
I have a Rogers Version

drapizan said:
Ok, After longs hours on the computer, I found a way to fix it and load back up the ROM.
I have also been able to do all your steps line by line with success. I have been able to upgrade to W6.1 but my treo 750 is NOT YET UNLOCKED!!!!
I have done it twice. line by line, number by number and step by step. All with ease but still not unlocked.
Can someone tell me how to unlock it now?
I have a Rogers Version
Click to expand...
Click to collapse
Glad you were able to fix it! Do you mind posting what you did hear in case others run into the same problem?
Why do you say it's unlocked? How did you come to that conclusion? If you were able to install WM 6.1 then technically that means your phone was unlocked (correct me if i'm wrong).

dubLeE said:
Glad you were able to fix it! Do you mind posting what you did hear in case others run into the same problem?
Why do you say it's unlocked? How did you come to that conclusion? If you were able to install WM 6.1 then technically that means your phone was unlocked (correct me if i'm wrong).
Click to expand...
Click to collapse
I had the black screen like the other member on this forum. I had to reinstall my previous ROM/OS (after 10 hours of searching on the net for it) successfuly and then followed the steps again you listed and was successful at upgrading with ease.
However my Treo is still not Unlocked. Not sure what I did wrong or what you recommend I do...

I tried the 2 steps of the Cheetah method and then the Magic Unlocker and still not working.
When I insert my SIM it says SIM LOCK
You have tried 30 times, please wait until timeout... What is that or what does that mean?
Im still on W6.1 and followed all your steps accordingly.

omg, pop my xda forum cherry baby, do you love me?
ok, so after years of lusting after a windows powered pda in one form or another, I finally copped a really really cheap Palm Treo 750 here in Australia. When I received this bad boy, it had WM5.something installed on it.
This step by step guide allowed me to fix any problems and successfully upload (on the first time!) wm6.1
do it guys, seriously. if you can install a new program on your machine,then you can hook this **** up.
fo' real.

drapizan said:
I tried the 2 steps of the Cheetah method and then the Magic Unlocker and still not working.
When I insert my SIM it says SIM LOCK
You have tried 30 times, please wait until timeout... What is that or what does that mean?
Im still on W6.1 and followed all your steps accordingly.
Click to expand...
Click to collapse
Where and when does it say SIM Lock? I've never seen this this issue before nor read about it in the forums anywhere.

the reverse gregama said:
ok, so after years of lusting after a windows powered pda in one form or another, I finally copped a really really cheap Palm Treo 750 here in Australia. When I received this bad boy, it had WM5.something installed on it.
This step by step guide allowed me to fix any problems and successfully upload (on the first time!) wm6.1
do it guys, seriously. if you can install a new program on your machine,then you can hook this **** up.
fo' real.
Click to expand...
Click to collapse
Glad everything worked for you!

Really sorry for late reply… anyway, I have tried and yes it worked but I had to do it manually.. First I have uploaded the file using RUUWrapper.exe successfully flashed my ROM to WM6.1
I don’t know what I was thinking of after that to try another ROM made with an uploader called “Kaiser” and I damaged my Treo “BLACK SCREEN”…  I got totally mad and I started to search all over the forums to find a solution since I tried to flash back to the original ROM, and tried like 2 or 3 ROMs but never succeeded to get my device boot up
I found a brilliant solution on http://forum.xda-developers.com/showthread.php?t=366771 which helped me to get my Treo up again
Finally it was by falt… but I still don’t understand the differences between :
1) Kaiser
2) Herman or I think they call it Hermes
3) Vouge
4) Raphael
6) Victor
Are there differences between all of them… are they depend on ROM type? What about Treo compatibility with the above types.. because my experience with Kaiser type cooked by someone I cannot recall his name was total failure..
finally i can say it was great experiance
Thanks

alpine with software locked on it

hi new to all this pda stuff, canany one help me!!!!!
i have been given a pda alpine, but it is locked with a program i carn`t get it to go into windows.
what is the best way way to get rid of this software?????
thanks

i assume you have tried hard resetting and then soft resetting once the HR has finished, in the wee 3 second window where it says customising.
Other suggestion would be to flash a new ROM.

big thanks!!!!!!
i said i was a newbii
ok i can start now, i have windows mobile on, ok whats next for me to do?????
how can i get rid of all that old software ??????

What sort of old software do you want to remove?
A hard reset should only leave you with whatever the carrier has decided to give you. If you do the soft reset trick you should be able to remove any carrier specific customisations leaving you with a bare(ish) Alpine. What you load after that is up to you.

ok so the software that was on when you started up the system has now gone???
i just have windows mobile on now when i start it up.
also i used the unlocker wizard, and it said it had unlocked, but i now have a no network ! mark instead of a strength signal???
any ideas please

Which version of the unlocker did you use? i had more luck with the older version. It sounds as though it hasn't worked, despite saying it had. From memory it does take a while to complete. Have you tried it with any SIM apart from your own one?

i used ver 1.6
and yes tryed it with 2 other sims, but still no luck they both the same.
is there anyway to reformat these pda`s start a fresh as they say
i said iam new

Yup, that's the newer version, i used version 1.5, SIM unlock.

Treo 750 Hard-SPL/Unlock/Unbrand Guide

Cannot get Hard-SPL on your Treo 750? Want to unlock/unbrand your Treo 750?
Check attached files to make your life easier.
Here is a guide to having a successful flash:
1) Create an ActiveSync connection with your phone.
2) THIS STEP IS ONLY FOR VISTA/WIN7 USERS! Follow the guide at this website first and complete all the instructions!
3) Download CheetahUnlocker to your computer, and extract the program - DO NOT RUN IT YET.
4) Download the attached Treo750UnlockFiles.zip and extract it to your computer. Take CHEEIMG.nbh and athena_unlocker.exe and copy them to your SD card.
5) Open/Run CheetahUnlocker.exe, and agree to the warning message. This will open a box with 3 options (2 are greyed out).
Option1:
Click "Flash SPL"
Click Next
Click the checkbox, then click Next
Click the checkbox (again), then click Next (again)
Click the "Update" button, then click Next
At this point CheetahUnlocker will send files to your phone to bypass the protection and flash your phone (called SSPL) and start your phone in bootloader mode. You may have to agree (on your phone) to these files being sent! Since we have placed the CHEEIMG.nbh file on your SD card CheetahUnlocker may respond with an error, ignore this error and click OK, it will go back to its original screen - DO NOT CLICK THE SECOND OPTION YET.
Your phone will find the CHEEIMG.nbh file on your SD card when entering bootloader mode and confirm that you would like to flash the file. Press the "Power/End Call" button to flash this file now, it should go rather quickly and say "Update Success" if all goes well.
After it is finished, pin reset your device using your stylus and the small button near the SD card slot. Your phone will boot up as normal, let it finish entering the OS and reconnect to ActiveSync.
Optional: Enter bootloader to confirm the flash by holding down the "Media" button (round button on left side) and using your stylus on the pin reset button (near the SD card slot) simultaneously. If all went well you should see SPL-1.4.0.OliNex.
Option 2:
Click "Unlock Radio"
Click the checkbox, then click Next
Click the "Update" button, then click Next
The program will flash an unlocked version of the radio to your phone. After it is finished it will boot normally, wait until it is done and has reconnected to ActiveSync. Around this time the program will prompt you with a box telling you it has to send files to your phone to unlock it, this will fail with an error. Click continue and the program will go back to its original screen. On your phone, locate the athena_unlocker.exe file on your SD card using File Explorer/Total Commander/Resco Explorer and RUN it. The program has 2 options, check both of these, then click "Unlock". This will unlock your phone, but we aren't done yet!
Option 3:
Press and hold "Shift" and "2" on your keyboard and click the title bar of CheetahUnlocker. This will unlock all 3 options. Click the 3rd option "Flash Normal Radio".
Click Next
Click the checkbox, then click Next
Click the checkbox (again), then click Next (again)
Click the "Update" button, then click Next
CheetahUnlocker will flash a normal working radio to your phone so that it operates normally. After it is finished, the phone will reboot and load as normal.
Congratulations, your Treo 750 (Cheetah) is now unlocked, unbranded, and ready to go!

need to hard-spl without computer
i'm in a limiting setting and would like to flash & unlock my locked at&t branded/locked treo 750. i can not in any reasonable way gain acces to a pc. is this possible if so how please? any help is appriciated.

pls can this method unlock treo 650

please i can't doing step 3, i press shift(pc) + 2(pc) + click in title bar of program but do not jump to 3 option.

tictac_m said:
please i can't doing step 3, i press shift(pc) + 2(pc) + click in title bar of program but do not jump to 3 option.
Click to expand...
Click to collapse
click in the textbox at the bottom of the program.

There's not connection with SD CARD
Sorry, but if i let it in the SD CARD in I recive a message of error conection.

sixtus said:
pls can this method unlock treo 650
Click to expand...
Click to collapse
this is not the correct place to ask that

Thank you
Thank you for your contribution! I applied this to my 750 that was sitting around doing nothing so that I can give it to my niece. I haven't been able to test if it works yet as I don't have a SIM for another network. Everything went as you described so I am crossing my fingers.

thanks man it worked like a charm.... i also cant wait for your WM 6.5 cooked rom.. it will be off the chain

Hi,
My brother just gave me his Treo 750 to replace my broken Hermes. I'm trying to Hardspl this device but without the need to hook it up to the computer. My brother lost the usb connection for the Treo. Is there a way I can flash the Hardspl with a MiniSD card? Please help cause this official WM6 on here is locked to UMTS only...cannot change to GSM. Any help will be much appreciated. Thanks in advance.

newbie
several days ago i upgrade mytreo from wm 5 to 6.5, but for several item didn't work such a camera, button, & can't switch to silent, & can't turn off (at the red button), & can't read mini SD 2 GB,need for the info to fix it, how should i do?

It isn't working D:
When I attempt this, it goes smoothly, but the SIM unlock isn't happening. When I insert the SIM after running step 3, I get this:
You have tried 76 times, please wait until timeout....
The app is sim lock, and I can't go to any other window.

I cannot create an activesync on the step 1...because my treo stucks in palm logo..please help me navenedrob .....

Is it necessary to do option 1,2 and 3?
My Treo is already simlock-free , so...
Thanks in advanced,
Rickson

you need to unlock the treo even your treo is a sim free. it is not the same...

libal said:
you need to unlock the treo even your treo is a sim free. it is not the same...
Click to expand...
Click to collapse
Ok, so i have to walk through option 1,2 and 3.
I'm gonna give it a go this week.
Thanx

Works great! originally lock At&t Treo 750 and now tested with t-mobile sim and work perfectly. Hardspl also in full effect...since then I've switch a bunch of time between each roms. Thank you for putting together this complete guide.

Anyone yet have a way to write over the Hermes radios 154.__.__ etc. yet

NickMl said:
When I attempt this, it goes smoothly, but the SIM unlock isn't happening. When I insert the SIM after running step 3, I get this:
You have tried 76 times, please wait until timeout....
The app is sim lock, and I can't go to any other window.
Click to expand...
Click to collapse
I have same problem with locked vodafone Treo 750. I can go thru all the steps, but at the and the phone is still locked. By the way I can upgrade to wm 6 or downgrade to wm 5. As I see I can not upgrade the radio rom of the phone.
Any help will be apprecitated.
Thanks to the forum.

y_aris said:
several days ago i upgrade mytreo from wm 5 to 6.5, but for several item didn't work such a camera, button, & can't switch to silent, & can't turn off (at the red button), & can't read mini SD 2 GB,need for the info to fix it, how should i do?
Click to expand...
Click to collapse
Read through the threads on the version of the 6.5 ROM you used. Some of the issues you are reporting are known bugs in various versions of 6.5 that have been posted.
For example, navenedrob has indicated he will be publishing an update to his 6.5 ROM which has fixes to most of his ROM's reported bugs, one of the major of which is the 'red button' issue you are experiencing.