Kaiser and flakey wi-fi access? - Tilt, TyTN II, MDA Vario III General

Has any one else with a Kaiser had problems with the wi-fi seeming sort of flakey?
Let me explain a bit....
I am sitting here at my lap top with a wi-fi connection that shows 4 bars and my kaiser seems to float in and out of wi-fi connectivity. If I look at wi-fi signal on the Kaiser ... Comm manager -> Settings -> Wireless LAN I get between 1 and 2 on the signal strength meter(stops just above the P on the 'Power Mode' tab).
I have the power tab settings set to best performance thinking that it boosts wi-fi amp gain or something but it doesn't seem to make any difference.
Today at work I sat immediately under a wi-fi antenna and while my lap top connected transparently with full bars my Kaiser while it could see the network could not connect.
On one or two occasions I have come back home and the kaiser would not connect at all. I shut it off and restarted and that at least got me connected...
Is this unusual? This is my first ppc and I am not sure how much I should expect.
Thanks.

my wifi works flawless at work and at home. havent tried on a public network yet.

Same here, mine works fine.

Related

Wifi signal gone

When on wifi my kaiser seems to loose the signal and picks it up again.
its just going on and off.
No problem with the routersignal all wireless computers work fine.
anyone knows about this problem?
cbgnl said:
When on wifi my kaiser seems to loose the signal and picks it up again.
its just going on and off.
No problem with the routersignal all wireless computers work fine.
anyone knows about this problem?
Click to expand...
Click to collapse
Have you put the slider to best performance rather than best battery?
Yes i did
never had the problem with the tytn and wizard.
I only get that on my TyTN II when I'm far away from the router and the signal strength is low. If you've already set the performance vs battery life slider to give maximum performance as suggested by kareem9nba and it's still behaving as reported, what happens when you're near to the router?
If it's just that your saying the range isn't as good as youve been used to with other devices, I have nothing to compare my TyTN II with as this is my first WiFi capable ppc - but I'm sure other more experienced members here will be able to comment. If you're near to the router where there's no doubt it should be working fine and still getting problems then thats a different matter.
maybe your router needs a restart or maybe its just faulty.
have you tried other devices with same router?
try a wifi sniffer/scanner see what happens (a good example would be PeekPocket)
mospantagruel said:
maybe your router needs a restart or maybe its just faulty.
have you tried other devices with same router?
try a wifi sniffer/scanner see what happens (a good example would be PeekPocket)
Click to expand...
Click to collapse
All other devices doenst have the problem output signal is ok but i ll try peekpocket
Flying Kiwi said:
I have nothing to compare my TyTN II with
Click to expand...
Click to collapse
I do! My Kaiser's performance is on a par with my old HTC Universal, which is to say, they are both terrible at getting a signal. I don't think my Kaiser is faulty as back in the Universal forums, it was often commented how useless the WiFi was in comparison to other machines. I used to have a HP Ipaq 5450 which could get a signal upto approx 20m from my router, my laptop starts struggling at around 50m. The Universal could just about get a signal upto 4m away, the Kaiser is no better.
I realise much of this is due router location and the fact that I was trying to get WiFi in my garage, but in my bedroom with a full signal on the laptop, the HTC devices struggle to get more than 1 bar and if I move 10cm further away from the router the signal goes completely.
I think the WiFi on the Universal and the Kaiser just isn't that powerful. I guess it's Maximum Performance setting is still quite low power in order to save battery life. Wonder if there is a registry tweek to increase the power to the WiFi card, and if doing that would blow the card?!
Steve-C said:
The Universal could just about get a signal upto 4m away, the Kaiser is no better.
I realise much of this is due router location and the fact that I was trying to get WiFi in my garage, but in my bedroom with a full signal on the laptop, the HTC devices struggle to get more than 1 bar and if I move 10cm further away from the router the signal goes completely.
Click to expand...
Click to collapse
I'm using an 11 Mbps Wifi capable router (about 2003 vintage) and even with a wall and a floor between my TyTN II and the router it still works about 15 m away, I've yet to try any further as that'd be outside the house. I was impressed to see it even detected other WiFi sources in the area though. I found that even though the signal quality bar was fluctuating, my web browsing still worked OK. Bumping the slider towards the performance end did make a difference to the signal quality indicator (although it still fluctuated). If your TyTN II is only working up to 4 m from your router then I think there's a fault with either device, you should be getting better than that.
I can connect to my linksys WRT54G when beside the it and 20mt away. Even when beside it the TynII will cycle off (disconnect) and then reconnect again. I thought it was signal strength but I am beginning to think its just a crappy wifi setup on the tyn. I also have my slider on best performance.
Flying Kiwi said:
I'm using an 11 Mbps Wifi capable router (about 2003 vintage)
Click to expand...
Click to collapse
Funny that, so am I! However I bought it because it was cheap and I really didn't know much about WiFi etc several years ago when I bought it. I notice many routers come with external antenna's, mine is all internal so I would think that it's more my router isn't that powerful, combined with the Kaiser having a less powerful WiFi set-up that older models. To be fair, the Ipaq had an external antenna (of sorts, a little lump on top) and my previous laptops didn't have built in WiFi, their external WiFi adaptors also had external antenna's.
Frankly I think that all this internalisation of components is having a negative impact on signal strength and range. To compare I have a GSM car kit with an external antenna that picks up a much better signal than a phone on it's own. Likewise my GPS can be connected to an external antenna and I've noticed when connected it will pick up more satalites, with a stronger lock, than when on it's built in antenna. It also picks up more than the Kaiser (internal antenna) or Universal (external bluetooth GPS with internal antenna) ever do.
Still, it all just about works for my needs, so I'm going to leave well alone!
Juzzman said:
I can connect to my linksys WRT54G when beside the it and 20mt away. Even when beside it the TynII will cycle off (disconnect) and then reconnect again. I thought it was signal strength but I am beginning to think its just a crappy wifi setup on the tyn. I also have my slider on best performance.
Click to expand...
Click to collapse
i have the same problem... i hope that's a firmware problem....
checked
i checked signal and even did hard reset on kaiser.
i still have full signal and goes to zero all the time
no clue here
eipiklein said:
i have the same problem... i hope that's a firmware problem....
Click to expand...
Click to collapse
But does this actually affect your browsing? In the end the signal quality bar can do whatever it wants as long as the data still gets through as far as I'm concerned and for me that’s happening. My hunch is that the reason why the signal quality bar intermittently dips down (even when nearby a router) is associated with power management on the TyTN II (which will still be in place to a certain degree even when the performance vs. battery life slider is fully at the performance end).
Flying Kiwi said:
But does this actually affect your browsing? In the end the signal quality bar can do whatever it wants as long as the data still gets through as far as I'm concerned and for me that’s happening. My hunch is that the reason why the signal quality bar intermittently dips down (even when nearby a router) is associated with power management on the TyTN II (which will still be in place to a certain degree even when the performance vs. battery life slider is fully at the performance end).
Click to expand...
Click to collapse
really i can't connect to my wifi router, while other hardware can (a laptop for example). it loops from "connecting" to "available" with 5 bars. but nevers connect or never shows an error. i tried open, WEP, WPA, WPA2 with no results... its a compatibility problem of TYTN II with some routers....
i hope that upgrading firmware, this problem dissapear....
Hi
My experience isn't that the signal itself is particlarly poor, but that it can be prone to loose connection regularly if its very weak. Atm I'm sitting some 150m from the accesspoint (quite powerfull transmitter), through a couple of concrete walls and its fast, as in almost so fast as the Kaiser can chew. Livestreaming from Youtube is np etc. The signal is no doubt very poor tho, and I have to use max signal/minimum battery on that bar you can adjust.
What drives me nuts is that it DCs me and often force me to key in the network key randomly every 1 to 20mins or so. I don't know if this is due to weak signal (both my laptop and the kaiser have 1 bar) or config of the wlan/kaiser. The PC dont DC, but its deffo a cranky connection. It almost seems like theres some auto-DC feature somewhere.
On other networks I haven't seen this. Generally I find the Kaiser wlan surprisingly powerfull, albeit it often shows a weak signal I've found this to be very relative and far from always descriptive of real life performance.
/Mac
kaiser wifi low signal - wi fi poor reception - wifi disconnecting and reconnecting:
Suffered a lot with my kaiser wifi poor reception. Tested several radio versions and could solve the problem.
Radio version:
1 71 09 01 - too low WIFI reception
1.27.12.11 - disconnecting and turning OFF the WIFI with no automatic reengage of the access point or turning ON the WIFI if coverage is good.
1.65.17.56 is the versione that SOLVED my problem.
This radio was collected from the original HTC shipped rom:
RUU_Kaiser_HTC_WWE_3.28.405.0_radio_sign_25.83.40.02_1.65.17.56_Ship.exe
In this moment I am running Radio 1.65.17.56 with
ROM jjblaster3 - updated 28014 with good WIFI behaviour.
I need to underline that the reception I have now with the Kaiser, can never reach the sensibility of my Nokia 5530 WIFI or the one I have on my laptop with good antenna embeded in my LCD framem but I am happy now because the WIFI is making sense now.
Best Regards
cbgnl said:
When on wifi my kaiser seems to loose the signal and picks it up again.
its just going on and off.
No problem with the routersignal all wireless computers work fine.
anyone knows about this problem?
Click to expand...
Click to collapse
I'm facing the same problem. WiFi worked fine and one day it was suddenly gone. Tried quite a few radios, including 1.65.17.56 and still no deal.
To elaborate, when WiFi is turned on, the icon never even comes up in the taskbar, and it continues to remain in an off state (when checked in wifi settings) even when it's turned on (in the comm manager).
I'm guessing this could be a hardware problem like a loose contact to the antenna? Anyone heard of such issues?
(On a side note, the phone function never worked either, I always got a "No Service")
I've fixed it! I believe the problem was indeed a loose antenna. I opened up my phone and removed the antenna peice (the plastic plate that also houses the speaker) and pushed up the two pins left of the camera (so that they'll have better contact with the antenna piece. Put everything back and now the WiFi works!
Now if only I can figure out why the cellular doesn't work..

Diamond Wi-Fi Problem

I have recently procured an HTC Diamond mobile and is facing the following problem:
I have a Linksys Router at home. When I switch on the Wi-Fi in my Diamond, it gets connected to the router. In the status, I can see the signal strength, Tx, Rx rate etc. But when I open the browser (both opera & IE), the web pages does not open. Error message stating check the url or does any other programme using the internet works? appears. Even my weather does not get updated. Using the same router, I am able to connect my laptop as well as my desktop to Internet.
When my diamond is synced using active sync, my mobile is able to connect to the Internet & Weather application also get updated.
Kindly help me to resolve this issue and make diamond connect to net using wi-fi.
Thank you in advance.
I have the same problem sometimes
I just changed parameter in settings -> connections -> wireless lan -> power mode -> "best performance" instead of "best battery" and it seems to work now.
I'm new to WM, so I don't know if it's a bug: when I don't use my phone I press the power button, or I wait it to go to "sleep mode" in 40s.
When I press power button to reactivate the screen, I can see in the first seconds that the wlan was disconnected and connects again.
So it seems that wifi is always disconnected when the phone is in sleep mode? That means no mails can be received ? Can anyone confirm?
Thanks
Hi there for both of you!
I had a connection problem with my Diamond at home. It was almost the same as tkak just I couldn't figure out whether ActiveSync connects or not. I managed to bypass this to set my routers DHCP timeout from 1 week to 3 hours and it all went away. The network status showed periodic connect/reconnect during the problem so it might be a different prob than yours.
Peio64:
WM6 keeps WiFi connection asleep during sleep mode. Imagine the battery usage if it was connected to WiFi all the time. So be happy with that and beside it is usable. WiFi automatically tries to connect to the closest hot-spot if it was connected before each time you switch on. Normally it shouldn't take more than 5-10 seconds and the whole process can be followed on the top bar.
Mails: Use DirectPush and GPRS connection and e-mails will arrive instantly. Google for setting this up. With Wifi I dunno - if you schedule ActiveSync for a periodic check whether your WiFi will be used or a new GPRS connection. I think GPRS can be used while the device is asleep but I'm not sure. Someone should test this. Probably whichever is quicker to build up a connection will be used for data transfer. (Note: on some forum I read that if you disable GPRS auto check with a tweak battery will last longer so I guess this means that GPRS is always connected.
Regs, Cina.
Does your diamond obtain an IP adress from your router, and is the connection setup as 'connects to internet'?
cina said:
Hi there for both of you!
Peio64:
WM6 keeps WiFi connection asleep during sleep mode. Imagine the battery usage if it was connected to WiFi all the time. So be happy with that and beside it is usable. WiFi automatically tries to connect to the closest hot-spot if it was connected before each time you switch on. Normally it shouldn't take more than 5-10 seconds and the whole process can be followed on the top bar.
Mails: Use DirectPush and GPRS connection and e-mails will arrive instantly. Google for setting this up. With Wifi I dunno - if you schedule ActiveSync for a periodic check whether your WiFi will be used or a new GPRS connection. I think GPRS can be used while the device is asleep but I'm not sure. Someone should test this. Probably whichever is quicker to build up a connection will be used for data transfer. (Note: on some forum I read that if you disable GPRS auto check with a tweak battery will last longer so I guess this means that GPRS is always connected.
Regs, Cina.
Click to expand...
Click to collapse
Thank you for your answer,
I had a SE P1i before, and wifi was connected all the time with push mail. With the diamond and its weaker battery, I set up my mails schedule to connect every 15 min so wifi only needs to be active every 15min, even in sleep mode, I don't want it to be connected all the time this is of course a battery waste.
HSDPA is connecting in sleep mode there's no problem with that, I just wish to use wifi for mails when I'm at home as my data plan is unlimited for web surfing but only 10Mo/month for pop/imap connections.
BTW I don't use the "keylock" option, is it different from sleep mode in this case? I can't see the advantage of keylock versus sleep mode
I had an ETEN M600 for ages before and I found that for sync it always used GPRS even if WiFi was available. The cause for this was GPRS was available while device is asleep so it can start syncing immediately after wake up (does it needs to wake up for sync?). So you probably have to switch GPRS (HSDPA) off while you're at home.
Keylock is for locking hardware buttons and touchscreen while it is active. (You won't dial up anyone from your pocket). It has nothing to do with sleeping just if you set up the registry tweak the device get locked (Keylock software is started) if you press power to send it to sleep. (I've almost written "off" but it is obviously not true - you can switch it off with a long press on power = soft reset).
Hope this helped a bit.
Cina
Okay thank you, I checked and HSDPA is connecting every 15min in sleep mode even with wifi ON. If I switch data off I suppose nothing connects and no mail is received, which is I think it's a weird behaviour.
By the way, I have set my data connection to swich off 10 seconds after not being used, and it works perfectly and reconnects automatiquely when it needs to. But for the wifi I can find that option, it's stays connected all the time when I use the phone, even if I don't need to. Is it possible?
Maybe it's due to the fact that it's always checking if there are new networks? On Symbian UIQ3, you can pre-configure networks, give manually priorities for each networks (1.Wlan work, 2.Wlan home, 3.3G etc..) and for each application (web, mail, etc). When the phone connects it checks if the network "1" is available, if it's not it checks the network "2", and once it's connected it doesn't check anymore. Is there a WM6 advanced network tool like that?
(Sorry for my english)
I did the following and now it gets connected to the web:
I just changed parameter in settings -> connections -> wireless lan -> power mode -> "best performance" instead of "best battery".
I do not know why this needs to be done like this.
Thankyou all for resolving my problem
I'm experiencing problems connecting to my WL Router (DrayTek 2820n) using WiFi when the router is set to Auto instead of to a specific channel. I've noticed from some threads for other mobiles that people are exprience similar problems. Does anybody knows what is the story around which channels are supported on WiFi: 1-11, 1-12 or 1-13. My router is set to 13 by default. In addtion to that Diamond has problem to connect to some channels even in the 1-11 range. So how can I check, which channels are supported and for which region?
Edit: I did further testing and it became obvious that when using Auto channel selection on the router, Diamond wouldn't connect. When selecting manually any channel between 1-11 it works OK, but when selection channels 12-13 it stops working, which makes me believe that the Diamond doesn't have support for the channels for non-US regions.
Does anybody have any idea how to change wifi region to support 12-13 channels as well? So far I couldn't find anything on the net that would help me doing it. Is it possible that it might be WM 6.1 issue and not Diamond?
HI I am actually having a diffirent issue but still related to wi-fi. When my phone awakes from sleep, it promts me to connect to my wi-fi server at home, when it was already connected jus minutes before. I have to re-enter the pass phrase everytime it awakes from sleep. This does not seem normal as my 6.0 touch didnt do that.
Any takers on this?
For more channels, it depend of US version or EU version. You need to changer your firmware but the problem is that in France for Internet you use PPoA and Belgium PPoE and I do not know if in the US they use the same so you will probebly losse your ability to connect to the Internet. Having more channels is not interesting because you need a hope of 5 between channels ( ex : ch1 + 5 = ch 6 and ch6 + 5 = ch11) between ch1 and ch6 place a ch11 for avoiding interferances. In 802.11g that is a question of scheme.
Sorry for my poor English.
Problem connecting to home network wifi
Hi, i've been using diamond to connect to my wifi home network but since few days is not possible anymore even if nothing was changed in the settings of the router.
The phone recognize the network as available, i push connect, it comes connecting but instead of connecting to the netwok it goes back to available.
Password is correct and the setting are the same as few days ago.
Any idea which setting should be modified?
Thanks in advance!
Panco76
Hello everyone,
I have one problem with my diamond. I disabled the "data transfer" with the improved comm manager. I usually use wifi when i'm home, however, i've seen that even though wifi is active, HSDPA connection is activated as well so i got charged, this sometimes happens when updating weather data or downloading emails.
Anyone with the same problem?
Yes - having he same problem.
I have WIFI at home and at work - so i want to use GPRS only when i am outside. never managed to do this - except when i kill GPRS fully - and even then Opera, the weather and push-mail wont work. :-(
WiFi Channels 12-13?
I need to bump up this issue again.
I can't find anywhere in this forum how would you change your WiFi channel range from US to EU (i.e. 1-11 to 1-13). My Diamond was purchased in Australia and I was hoping that the new SW upgrade would rectify that, but it looks to me that's not the case. Any idea if that can be done in registry?
Thanks.
Change Channel range from 1-11 to 1-13
***Bump***
Has anybody got any ideas how to increase the channel range from 1-11 to 1-13?
Hi, I am having a seperate problem from all that are listed. I have the linksys rangeplus router, and my Diamond wont even detect my network when it searches, yet my computer and PS3 do fine. Can anyone help me?
another problem...
Hi,
i have a problem with the wifi on my Diamond aswell..
I have a router at home which is encrypted. When I try to connect to it, I type the encryption key and it says Connected but i cant surf any pages. When i go back to wifi settings my home network switches between Not available and Connecting...
However, when i remove the encryption, everything seems to work fine. Since i dont want to treat my neighbors with free internet, does anyone have any tips for me?
(it is set to Best performance... +i'm sure i enter the right key...)
Thanx
The same over here... I found out, that some of cooked ROMs had this problem, but official worked. Before I couldn't connect via WPA2-PSK AES, all other encryptions worked. Until now... I tried to flash official ROM and RADIO, but it doesn't work anymore. I'm pretty sure it must be hardware problem. I need to send my Diamond to get fixed, but... The closest repair centre is in Prague (GSMobile)
!!!!!!!!!!!!!BUT BE AWARE!!!!!!!!!!!
I owned previously Qtek8310. After I send them my Qtek to replace the joystick, it came back with broken motherboard... This repeated 3 times and everytime they broke something else. I've got my Qtek8310 back as a total crap, destroyed and scratched... I called and send a claim to HTC Europe in London, but nothing happened since then. I don't believe them anymore. If you love your Diamond avoid to get it fixed in GSMobile!

[Q] Connection behaviour like Nokia?

Hello guys,
this is my first thread here in this forum. I got my TyTN-II 2 Weeks ago, a used device for 99 Euros. A good deal, i think. After playing around with some of the Roms i found here, i found M-Diamond 1.2 to fit most of my needs. When first used the phone, i disliked the behaviour of connecting to hsdpa, 3g or something else that was inside coverage, and not releasing the connection. The longest time i experienced was 3 hours of open but inactive connection. I found out, WMLongLife could help me greatly, together with the option to kill connections when standby is enabled i thought there shouldnt be any connection at last, when i leave the phone unattended with 1 minute auto standby.
But that was an error. Yesterday i was driving around in my car, having paired the phone with my bluetooth car-hifi and while listening to the great sounds of dj doboy i heared these noises from my phone establishing a connection! the noises weren't all the time. it seems it was some sort of keep-alive. no, it wasnt the sound of the phone registering to another antenna. this occured even when i stood in a parking lot. what the hell? i double checked the configurations but everything seemed fine. but why the hell is the phone establishing a connection.
Second issue may depend to the first one, since it touches connections, too. When i reach my Work or my Home, whose access points are stored in my phone, it connects to them... and keeps the connection. all the time! even if its unused. that drains the battery to zero in a very short time. I looked over the configuration of WMLongLife, but found nothing helpful related to switching wlan of when unused. i found one option inside the wifi configuration page, telling windows mobile to switch off wlan after x minutes. i tried the lowest setting and waited. it disconnected and disabled wlan. but instead of re-activating and re-connecting it when trying to use the browser, it used the 3g-connection WMLongLife was establishing automatically (what was correct because i told it to give the browser 3g access when no wlan is connected).
my old nokia (n95) establishes a wlan connection only if needed and kills it when the establishing program closes. too, there was a tool called smartconnect, where the user was able to put a stack of connections and create one single connection out of it, enabling the nokia to choose itself what available connection should be used. i used to put my home wlan in first place, second was the work wlan and third was the mobile net. i tested and trusted this constellation even in standby mode because it does what it promised. one Battery charge lasted about 5 days.
Windows Mobile connects.. to wlan forever, searches wlan networks forever, connects to mobile net sometimes for whatever even if connected to wlan, even if told not to do so, draining both my flatrate and the battery power in an useless way. mail synchronization is enabled any 2 hours only, weather info is disabled. one battery charge lasts a half day when not making any calls. so what keeps windows of connecting all the time?
is there any way to adapt the behavior of the nokia phone to my kaiser? maybe the connection architecture is not able to do this because windows uses its connection points in another way like nokia does. But perhaps there is a tool to do this?
Any suggestions?

WiFi Issues

Hi Everyone
I looked and I could not find info on this issue. I have just used WiFi at home in the past with the Note 3 and it was fine. Here is some history of the changes:
- Old home WiFi was single band wireless N (53mbps) with a second repeater hot spot. This worked well with the Note 3.
- Had issues with the router so I upgraded to a dual band ac router and removed the second hot spot. So now it is just the new router for the whole house.
- Issues now - receive 2 bars at the far end of the house and basic WiFi is OK. Watching You Tube is an issue and it loads, plays for a few seconds, loads more etc.
I don't see a way to tell if I am on ac or wireless N. I was going to try to switch to wireless N and see if that helped but I can't see a way to do this? This router is way faster than my old one so I thought speed would not be an issue. no one else is using the wireless in the house. I would think that 2 bars would be strong enough? I think that wireless N would have a better range so that is why I wanted to try that. I am assuming that I am connecting to ac. Any thoughts?
thx in advance
AC routers have two separate ssid's. One for b,g,n. And another for 5G band. The 5G band default ssid is the same as the other with "5G" at the end. 5G band doesn't have good range, but it has faster speed between connected devices. 5G won't have faster internet unless you have a 100mb download speed. Which is unlikely. So your YouTube issue is either your modem, or a Qos setting in the router. If your router is at default settings it's definitely your modem.
You might be able to get more support on this subject thru a forum for your router, or modem.
scottwood2 said:
Hi Everyone
I looked and I could not find info on this issue. I have just used WiFi at home in the past with the Note 3 and it was fine. Here is some history of the changes:
- Old home WiFi was single band wireless N (53mbps) with a second repeater hot spot. This worked well with the Note 3.
- Had issues with the router so I upgraded to a dual band ac router and removed the second hot spot. So now it is just the new router for the whole house.
- Issues now - receive 2 bars at the far end of the house and basic WiFi is OK. Watching You Tube is an issue and it loads, plays for a few seconds, loads more etc.
I don't see a way to tell if I am on ac or wireless N. I was going to try to switch to wireless N and see if that helped but I can't see a way to do this? This router is way faster than my old one so I thought speed would not be an issue. no one else is using the wireless in the house. I would think that 2 bars would be strong enough? I think that wireless N would have a better range so that is why I wanted to try that. I am assuming that I am connecting to ac. Any thoughts?
thx in advance
Click to expand...
Click to collapse
why not use your old router from your old home as a repeater? wouldn't that work?
scottwood2 said:
- Issues now - receive 2 bars at the far end of the house and basic WiFi is OK. Watching You Tube is an issue and it loads, plays for a few seconds, loads more etc.
Click to expand...
Click to collapse
That's called buffering and it's due to low thruput (which is different than speed). It can be caused by low signal strength (due to distance or to the signal haveing to go through too much along the path), noise between the router and the phone, interference with someone else's wifi signal ...
You need at least a couple of apps like Signal Check Lite and Wifi Analytics to see what's going on. Guessing isn't going to give you a solution.

Wifi management programs only seeing one wifi node

I have a wifi router / gateway in my home office, and an access point at the other end, downstairs of my home. Wifi Manager worked fine to switch to the best signal on my old Nexus 5 with stock Lollipop. Now I have a new Galaxy Note 4, and it will only select the access point, which is weak in my office. So I tried Wifi Prioritizer and Best Wifi, and they both only show the remote access point, even though I am sitting five feet from the gateway. So Wifi Prioritizer only shows the one, and I have no menu button to force a scan, set priorities, etc. I have tried the various wifi configurations under Lollipop; no change. The OS Wifi page shows them all, and indicates the office node is much higher signal strength.
Resolved
OK, a big Duh on me. I would delete this if I could, but I'll leave a note in case someone as clueless as I does this! In setting up my new phone I didn't enter passwords for all of my wifi nodes, so there was only one shown because only one that could be accessed. Actually, I appreciate that Wifi Prioritizer doesn't show a bunch of routers that aren't mine; Wifi Manager did.
M

Categories

Resources