hi guys i have the following problem
i just replaced a new LCD+touchscreen on my 8125 (G3) and i can't connect it on ActiveSync... it simply wont recognize it.. even before i changed it i wasnt able to connect ppc to computer... but when i attach the usb to PC i hear the voice of something connected on USB port, and than the ballon pops out and says me the device was not properly connected...
i've tried changing older and newer ActiveSync's programs, they all function as same... when i press camera+soft reset (bootloader mode) i get the bootload mode and on the bottom i can see when i attach USB... but still it wont update any ROM to PPC... i even tried removing the mark from ActiveSync menu saying ''Allow USB Connection with this desktop computer'' but still it says me device not recognized... wtf?!?! I cant do nothing, upload ROMs neither browse...
please any help appreciated...
and yes, i tried hard reset too and i get the same... tomorrow ill go on 2nd PC to try on it but i have a feeling i'll get the same error there...
HELP!
thx bb
Papcina said:
hi guys i have the following problem
i just replaced a new LCD+touchscreen on my 8125 (G3) and i can't connect it on ActiveSync... it simply wont recognize it.. even before i changed it i wasnt able to connect ppc to computer... but when i attach the usb to PC i hear the voice of something connected on USB port, and than the ballon pops out and says me the device was not properly connected...
i've tried changing older and newer ActiveSync's programs, they all function as same... when i press camera+soft reset (bootloader mode) i get the bootload mode and on the bottom i can see when i attach USB... but still it wont update any ROM to PPC... i even tried removing the mark from ActiveSync menu saying ''Allow USB Connection with this desktop computer'' but still it says me device not recognized... wtf?!?! I cant do nothing, upload ROMs neither browse...
please any help appreciated...
and yes, i tried hard reset too and i get the same... tomorrow ill go on 2nd PC to try on it but i have a feeling i'll get the same error there...
HELP!
thx bb
Click to expand...
Click to collapse
Which Windows are you at ? use winXP SP2,disable anti virus if any installed,also disable any firewall even windows own firewall.Disconnect phone from the usb cable and remove any sdcard if any.
Uninstall Active sync,Reboot Pc,open Windows Task Manager--->Processes Tab--->End wescomm.exe process.Reconnect phone via usb cable,get your phone into boot loader mode,check small usb appear a the bottom of bootloader screen and run the ruu...,hope it'll work out.
For Active sync connectivity,reinstall ,make sure no anti virus or firewall is running,connect phone with usb and let it synchronise.
Is your usb cable compatible,does it charge ?,if not,get a new usb cable. secondly, check if your mini usb port of your phone is working or it might be damaged.
Which Windows are you at ? use winXP SP2,disable anti virus if any installed,also disable any firewall even windows own firewall.Disconnect phone from the usb cable and remove any sdcard if any.
-->yes, win xp sp2, done all that already..
Uninstall Active sync,Reboot Pc,open Windows Task Manager--->Processes Tab--->End wescomm.exe process.Reconnect phone via usb cable,get your phone into boot loader mode,check small usb appear a the bottom of bootloader screen and run the ruu...,hope it'll work out.
-->nope, doesn't work dam...
For Active sync connectivity,reinstall ,make sure no anti virus or firewall is running,connect phone with usb and let it synchronise.
-->it won't crap...
Is your usb cable compatible,does it charge ?,if not,get a new usb cable. secondly, check if your mini usb port of your phone is working or it might be damaged.
-->tried several USB cables, all of them charge normally the unit.. i don't get where the f*** im making the mistake...
ok im really nuts now...
been on a 2nd pc, same problems there...
i can't do nothing with it! i tried even backing up on SD, but mtty won't connect... nothing... i have to cid unlock it, none ROMs work...
what the hell i do now? is there anyone in eastern/middle europe who can reflash the rom? i gave days and days for reading the forums and trying out to lock out this dam phone but i simply can, and i think i'll brick it in the wall
guys, any idea how can i get it over USB????
thx
b b
Papcina said:
ok im really nuts now...
been on a 2nd pc, same problems there...
i can't do nothing with it! i tried even backing up on SD, but mtty won't connect... nothing... i have to cid unlock it, none ROMs work...
what the hell i do now? is there anyone in eastern/middle europe who can reflash the rom? i gave days and days for reading the forums and trying out to lock out this dam phone but i simply can, and i think i'll brick it in the wall
guys, any idea how can i get it over USB????
thx
b b
Click to expand...
Click to collapse
Try this, on the 8125 run activesync, if you have partnerships there (IE. if the screed has "windows PC" on it), then go to "menu" on the lower right, then "Options" then select the "Windows PC" and delete it. Delete all partnerships that you have.
Then close activesync on the 8125 and go to "Start/setings/Connections/" and open your "connections". Do you have connections set-up? Make sure you have at least one connection set-up. Then close that and open your "USB to PC" is "Enable advanced network functionality" is the box checked? if it's not then check it (if it is then uncheck it), then connect your BSB cable and see if activesync on the PC will detect it.
If it does then set-up a new partnership.
Papcina said:
ok im really nuts now...
been on a 2nd pc, same problems there...
i can't do nothing with it! i tried even backing up on SD, but mtty won't connect... nothing... i have to cid unlock it, none ROMs work...
what the hell i do now? is there anyone in eastern/middle europe who can reflash the rom? i gave days and days for reading the forums and trying out to lock out this dam phone but i simply can, and i think i'll brick it in the wall
guys, any idea how can i get it over USB????
thx
b b
Click to expand...
Click to collapse
Well I think you have a damaged mini usb port of your phone,for info read this thread
http://forum.xda-developers.com/showthread.php?t=334440
I have been trying to resolve my AS Not Connected for a long time, over 1 year. I have tried all know recommendation/solutions to no avail.
Have read that FixASRunAT will fix the problem. Go to:
http://www.cs.pitt.edu/~jmisurda/ppc/FixASRunAt.zip
I downloaded it last night and will try reconnect tomorrow as I am out of town and cannot try AS now. iWill report back the results.
If this works for you, let us know. Wish you luck as I need it, too.
calouro said:
Try this, on the 8125 run activesync, if you have partnerships there (IE. if the screed has "windows PC" on it), then go to "menu" on the lower right, then "Options" then select the "Windows PC" and delete it. Delete all partnerships that you have.
Then close activesync on the 8125 and go to "Start/setings/Connections/" and open your "connections". Do you have connections set-up? Make sure you have at least one connection set-up. Then close that and open your "USB to PC" is "Enable advanced network functionality" is the box checked? if it's not then check it (if it is then uncheck it), then connect your BSB cable and see if activesync on the PC will detect it.
If it does then set-up a new partnership.
Click to expand...
Click to collapse
not working crap, i think now i have a damaged miniUSB..
i'll try to solve that by getting an BT dongle.. btw, is it possible to flash new ROM with BT?
@asctony i cant open that link, can u plz send me the file on my mail?
Papcina said:
not working crap, i think now i have a damaged miniUSB..
i'll try to solve that by getting an BT dongle.. btw, is it possible to flash new ROM with BT?
@asctony i cant open that link, can u plz send me the file on my mail?
Click to expand...
Click to collapse
Although it is possible to perform all actions with BT,like you do with normal active sync connectivity via usb,but No,You cannot flash a new rom through BT,you got to have a physical connectivity established between phone and your pc via usb and usb is shown at the bottom of the bootloader screen.Even during active sync connection,while flashing active sync is automatically disabled by the RUU and the flashing is still carried out by usb only.
crap... so the only logical solution that has left me is to give ppc to sum1 who will desolder/resolder the miniUSB connection back again... but still, i dont get it, i opened few times and i dont see any wire in miniUSB connector loosen or bricked... everything is fixed and on its place...
Papcina said:
crap... so the only logical solution that has left me is to give ppc to sum1 who will desolder/resolder the miniUSB connection back again... but still, i dont get it, i opened few times and i dont see any wire in miniUSB connector loosen or bricked... everything is fixed and on its place...
Click to expand...
Click to collapse
That's it !!!
there might be a tiny contact of the mini usb port which needs to solder,these tiny contacts are not sometimes visible to the naked eye,it can only be verified by checking with 'Voltmeter' and this can only be done by a person who has some knowledge about electronics repair and soldering.If you can do it,get a Voltmeter and can check the connectivity of all the five tiny connectors,good luck
dont worry i got this ****ing problem too
bootloader mode works but.....
I CANT CHARGE or CONNECT ON ACTIVE SYNC
BS!!!!!!
Mine will charge No Prob with both PC/USB Cable and Standard charger,PC takes FOREVER,It recongnizes a Smart Phone on both XP and Windows 7 but then says Not Installed correctly,No Drivers,ect. It has to be a Hardware issue with the Port or something,In "Comm Manager" there is always a "Check" Mark through the Activesync Selection,no way to get it to "enable" on the Phone Screen....Phone is not worth enough to hassle fixing it,it works fine,I have to use another phone to put stuff on my storage card,can I load windows 6.5 and unlock with the SD Card method?Thanks,Vegas
I have a G3 wizard. I was stupid and trying to go from button's ROM to Crossbow reloaded. The flash ended up crashing somewhere in the 80% range. Now my wizard will rarely get into bootloader mode. I'm leaving the battery out for 5 minutes at a time. When I put it back in it will go into bootloader mode until I plug the USB cable in it and try to flash it the screen comes goes grey and I get a 260 update error..
I really hope I didn't brick this thing, It's my only connection and I have some important new job related calls to make!
mine is stuck on the flash screen
i have a g3 wizard and today it would not get past the windows mobile 6 professional splash screen (tnt rom). is there anything i can do. i tried reflash it but could not establish a connection. please help
tarusdg said:
i have a g3 wizard and today it would not get past the windows mobile 6 professional splash screen (tnt rom). is there anything i can do. i tried reflash it but could not establish a connection. please help
Click to expand...
Click to collapse
Try holding the camera button while powering it on. Then put in the usb cable and flash away.
tarusdg said:
i have a g3 wizard and today it would not get past the windows mobile 6 professional splash screen (tnt rom). is there anything i can do. i tried reflash it but could not establish a connection. please help
Click to expand...
Click to collapse
Do a Soft reset of the phone,if it works out,fine,otherwise do the Hard reset,although you might lose your personal data but phone will work out.
If both do nothing and it still gets stuck,then there's no other way except to reflash.
Which connectivity your not getting,If you are saying about Activesync connectivity,then you don't need Activesync connectivity to flash,get your phone into Bootloaders(multicolor screen) connect it to your pc via usb cable,when usb appears at the bottom of the bootloadermode,flash the Rom.
But if you cannot establish connectivity through usb cable,then either your usb cable is faulty or the mini usb port of the phone is damaged.
Looks like i've been threadjacked...can anyone help?
Hey guys, today I tried flashing my TNT wizard to a Diamond rom. I got an error about 1/2 way through (on my computer) and the updater shut itself down. My device restarted, and is now in bootloader mode. It's connected to my PC, say "usb" at the bottom left of my device but active sync doesn't see it. What should I do? I can't flash it or anything because none of the updaters can communicate with the device.
Actually, it looks like button rom worked for some odd reason. Thanks anyway guys.
Activesync doesn't work in Bootloaders,but if small usb appears in bootloaders,it means its establishing connection and it can be flashed.
Hi,
I upgraded to several different versions of WM6.x (almost all above) but have the same problem. After UG I can't install any software through AS or browse the device with Explorer. Explorer shows no contents and the software screen opens but shows only a frame. I had the same problem with a Hermes and solved it by unchecking the extended network options in settings>connections>USB to PC but when I do that with the MDA II it freezes when I place it in the docking station. I then have to SR. I replaced the serialusbfn.dll with the one available on another post but AS will no longer recognize the device.
Any ideas? I've downgraded to WM2k3SE until I find something that works.
Btw, yes I did do a proper HR (n, yes,yes)
Cheers
First of all you need AS-4.5
If yes, check the settings in windows firewall.
If you are using some other firewall or virus guard, disable it temporarily.
Right click on AS icon in system tray & select Connection manager, enable USB.
Delete previous partnerships in AS.
Restart the PC & try to connect.
If it fails you can follow the diagnostic procedure which gives a error code, or possible cause. Check the error code with Microsoft web site.
You can also try to uninstall & reinstall AS
Hi,
I've tried all of that before (should have said so, b4). Here is a little more info:
I sync with 2 different computers, one at home (no network) and one at work (network). Both run WinXP Pro. I only have this problem with the work computer and only when WM6.x is intalled on a MDA II. The problem goes away when using WM2k3SE or when using a Hermes with WM6.x. Since the Hermes works without problem, I don't think it's the desktop.
Something causes the MDA to freeze when activesynce starts. Even the charging light stays on when I pull the unit out of the docking station. Backlight stays at full brightness and it doesn't go to sleep after a time. No buttons (even on/off) work. I can only SR.
Help!
Known problem
Read and try this:
http://forum.xda-developers.com/showthread.php?t=396081
Hi Muckelmaus,
thankx but I tried that. It causes the device to not be seen at all. I cradle it and nothing happens.
Cheers
Recently I'm unable to sync my Vario III with my Vista x64 or Windows XP Pro desktop PC's. I don't sync often - last time was in March which worked fine.
At first I thought the problem was with WMDC on my Vista PC. I uninstalled WMDC re-installed, but it's made no difference.
The symptoms i'm getting are that when I start WMDC with the phone connected sing USB, I get the splash screen, then it sticks and goes no further. WMDC will start only if the phone is not connected.
If I plug it into the XP Pro PC, Activesync 4.5 starts, the animated ball spins in Activesync, but doesn't complete.
I think the problem is with the phone rather than either WMDC or Activesync, as I can start Pocket Controller on Vista and see the phone, and I can connect to the phone using Co-Pilot Central to download speed camera updates.
The last thing I did was to the phone was install Google apps like Youtube mobile and Search. Can these interfere with Activesync and WMDC? I've removed them but it still won't connect.
I've tried changing the USB connection type from advanced to normal, but that didn't fix it.
I get the usual windows sounds upon connection and disconnection, but WMDC doesn't work.
One clue here. If I set a password to protect the phone, upon connection, the phone locks and the PC says to unlock the phone. I type the password on the phone to unlock it, but the PC sits there with the same message to unlock the phone. So WMDC sees the phone up to a point.
I've also removed the partnerships from both the phone and the PC's, but neither WMDC or Activesync detect the phone as a new device. Activesync on the phone shows no errors.
I've tried everything I can think of and am still convinced it's a phone problem. I've searched for similar problems on XDA but haven't found anything similar.
Sorry for the long post!
Any ideas?
Thanks
Mike
Tried another cable?
ChumleyEX said:
Tried another cable?
Click to expand...
Click to collapse
Yes. Made no difference. Didn't see how it could really - since apps like Pocket Controller and CoPilot Central can see the phone.
I've had many activesync/WMDC problems over the years but never one quite like this. It wouldn't be so bad if it gave an error message or something, but it doesn't. There's nothing related in the event log either.
Baffled!
mtcs said:
..... There's nothing related in the event log either.
Baffled!
Click to expand...
Click to collapse
Woops. How did I miss it. There is something in the event log.
'Windows Mobile-based device failed to connect due to communication (0x80072745) failure (see data for failure code).'
I tried looking up the code using the Event Log Online Help but it has '...no additional information at this time'.
Oh well. At least I've got something to Google.
I figured it out. It was the device - the MDA Vario III.
My girlfriends phone - Palm Treo Pro - connects ok to the Vista PC on her account. WMDC worked fine with it. I plugged in my Vario III whilst still logged into her account, and WMDC wouldn't work.
I tried it on my account one more time, still wouldn't work. Reset the phone to factory defaults, re-configured it, connected it to the Vista PC, and WMDC worked fine.
I have no idea why it wouldn't work right before. In all other respects the phone was fine.