Hello guys;
I had a new HTC Wizard yesterday. It's a Orange M3000 French one. It has already loaded with 1.03 Rom.
My IPL : 1.03
My SPL: 1.03
I suppose that i have a G3 device.
According to this tutorial. http://forum.xda-developers.com/showthread.php?t=285435
I have firstly ran lokiwiz 0.2b, i have successfully sim-unlocked the device, then i re-ran lokiwiz for CID Unlock (SuperCID) which gave me:
"Your phone is now CID unlocked....".
Please note that my battery is fully charged.
Then i have downloaded T-Mobile 2.26 Rom, and started it. It recognized my device, it says that it will update my device, and it shows me the progress bar indicating that it can take 10 minutes.
The problem is, on this screen, it reboots my device, my battery light becomes orange, and 10 seconds later, the light goes off, and the device is turned off. Update utility gives me ERROR 260, Update ERROR.
I have to remove the battery, re-insert it to boot my device again. Please help me, i'm really stuck guys.
Cheers
etron45 said:
Hello guys;
I had a new HTC Wizard yesterday. It's a Orange M3000 French one. It has already loaded with 1.03 Rom.
My IPL : 1.03
My SPL: 1.03
I suppose that i have a G3 device.
According to this tutorial. http://forum.xda-developers.com/showthread.php?t=285435
I have firstly ran lokiwiz 0.2b, i have successfully sim-unlocked the device, then i re-ran lokiwiz for CID Unlock (SuperCID) which gave me:
"Your phone is now CID unlocked....".
Please note that my battery is fully charged.
Then i have downloaded T-Mobile 2.26 Rom, and started it. It recognized my device, it says that it will update my device, and it shows me the progress bar indicating that it can take 10 minutes.
The problem is, on this screen, it reboots my device, my battery light becomes orange, and 10 seconds later, the light goes off, and the device is turned off. Update utility gives me ERROR 260, Update ERROR.
I have to remove the battery, re-insert it to boot my device again. Please help me, i'm really stuck guys.
Cheers
Click to expand...
Click to collapse
No doubt it's a G3 device with ipl/spl 1.03,cuz G4 devices does not have ipl/spl 1.xx and as ipl/spl 1.xx is required to unlock phone using lokiwiz02b,there is no need to downgrade to 1.xx through button's rom 1.05
ERROR 260 : UPDATE ERROR
This error occurs when there is an “open port error” before upgrading the CE ROM image.
Solution: You can reset the device and run RUU again. If you still encounter an “OPEN PORT ERROR” again, reset your computer and try again.
What is the status of your phone at present ?
Does it wok normal,it loads up the previous version of OS which installed with ? or it goes into bootloader mode(multicolor screen) ?
Well,if it works normal download WST tool and check the status of your phone whether it's CID locked or unlocked,but,if it goes into bootloader mode ,than download official carrier's Rom from it's website and get your phone into bootloader mode (multicolor screen) and flash it,it'll start normal and revert back to your default status,then check the CID lock/unlock and proceed further for upgrading as the guide instructs,cuz I presume your phone is not cid unlocked,good luck
Thanks for your kindly reply zabardast_1;
I've made a "Clear Storage" so it restored the previous ROM (i suppose). The previous OS is currrently running OK, booting up OK, showing IPL/SPL/RADIO values, reading my sim card. So when i'm testing the device with mestrini tools, (Wizard Service Tools), the output is:
Code:
Wizard Service Tool v4.2.1
20/10/07 14:10:05
CPU: Texas Instruments - OMAP850
MODEL: Wizard
=> Bootloaders:
IPL: 1.03 (G3 device)
SPL: 1.03 (G3 device)
Built on Sep 29 2005 at 14:49:19
=> Firmware:
OS: 5.1.xxx (Build 14406.1.1.1)
ROM: 5.1
Registry AKU: .1.1.1
Radio: 01.04.10
Protocol: 4.0.13.17
=>Extended_ROM:
Version: 1.3.1.105
Name: Extended_ROM
Status: hidden
=> Drives and partitions:
|--Handle--|---Size---|
2e9eb472 - 10.00M (0xa00000)
aeae8ede - 48.23M (0x303c000)
afb2bf42 - 51.06M (0x3310000)
8fb2bd82 - 2.88M (0x2e0000)
2fb2bd5e - 3.06M (0x30fc00)
=> DOC chip unique ID:
00000000a51301022f060f9b0409059e
Key Index: 14
All Done.
Code:
Reading CID block...
Calculating CID block sum...
CID checksum: 36CC9888
Decrypted stored sum: EFD39CB041D1FD5D
Decrypted calcd sum: EFD39CB041D1FD5D
Key index : 14 - Block index: 44
CIDkey: MODULESN
CID: 11111111 (SuperCID)
Phone is already CID unlocked!
Please note that IEMI read on ROM and CID is the same, i have just removed them from copy-paste. There is something bizzare, because i have a formatted mini-SD card which is not recognized in drive & partitions. (it's a 512 mb mini-sd).
For going into Bootloader mode, I use the method above:
-> perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up.
When i try to make a soft reset, it works. The device restarts itself correctly.
When i push the reset button and try to hold the camera button, the device remains shut down.
I really don't understand what's happening. I really need some help. Thanks in advance.
Hello guys;
If someone reading this message, please read below for the solution if you have a Htc Wizard (Orange M3000) French with 1.03 ROM. (1.03 IPL / 1.03 SPL)
A Thread that contains exactly the same problem: here
Please read carefully "xeno1" response. When i was trying to go into bootloader mode, it was unsuccessful everytime. So turn off the device (not stand-by, turn off), then please remove your mini-sd storage card (if any), remove the usb cable. (Be sure that your battery is charged over %50, mine was over %90).
When done, push the camera button, then push the "power" button, wait a little while, when the device will come up, it will be in the bootloader mode,
(red, green, blue), and will show your IPL/SPL values. Connect up your USB cable. "USB" will appear on the bottom of the screen.
Now you are ready to flash your device. I'm pretty sure that you must follow the following tutorial for flashing.
http://forum.xda-developers.com/showthread.php?t=285435
I've downloaded Button Rom (1.05) and successfully flashed my device on bootloader mode. Please be patient when you're flashing your device, even
if %98. It can wait a little bit, 5 ~ 7 minutes. Enjoy!
Edit:
Once you have flashed with Button Rom, you can use lokiwiz 0.2b, or Wizard Service Tools for SIM Unlock + CID Unlocking operations. Once done, you can go to flash with T-Mobile 2.26 Rom. When flashing, it can also wait at %85, please be patient.
And thanks to XDA crew, forums members.
etron45 said:
Hello guys;
If someone reading this message, please read below for the solution if you have a Htc Wizard (Orange M3000) French with 1.03 ROM. (1.03 IPL / 1.03 SPL)
A Thread that contains exactly the same problem: here
Please read carefully "xeno1" response. When i was trying to go into bootloader mode, it was unsuccessful everytime. So turn off the device (not stand-by, turn off), then please remove your mini-sd storage card (if any), remove the usb cable. (Be sure that your battery is charged over %50, mine was over %90).
When done, push the camera button, then push the "power" button, wait a little while, when the device will come up, it will be in the bootloader mode,
(red, green, blue), and will show your IPL/SPL values. Connect up your USB cable. "USB" will appear on the bottom of the screen.
Now you are ready to flash your device. I'm pretty sure that you must follow the following tutorial for flashing.
http://forum.xda-developers.com/showthread.php?t=285435
I've downloaded Button Rom (1.05) and successfully flashed my device on bootloader mode. Please be patient when you're flashing your device, even
if %98. It can wait a little bit, 5 ~ 7 minutes. Enjoy!
Edit:
Once you have flashed with Button Rom, you can use lokiwiz 0.2b, or Wizard Service Tools for SIM Unlock + CID Unlocking operations. Once done, you can go to flash with T-Mobile 2.26 Rom. When flashing, it can also wait at %85, please be patient.
And thanks to XDA crew, forums members.
Click to expand...
Click to collapse
Thanks for the little tutorial and advise,glade you got it working.
That's why it has always been emphasized time and again to go through the concerned subforum and threads ,read and fully understand.It's all there in the forum,only it's upto you how to get it.You know now that you searched and you got it right,this is called 'Self help',cheers
etron45 said:
And thanks to XDA crew, forums members.
Click to expand...
Click to collapse
Congratulations on your progression in such a short time and on such great posts with precise info.
This forum would be much nicer with more 'newbies' like you... but then again so would be the world if we'd all be nicer to each other
cheers
Your tool WSS (Wizard Services Tool) is a great tool mestrini, it's more easier to use. A GUI is very helpful for a beginner than a text-based tool. Besides, lokiwiz is a great tool for the scene. Thanks for bringing these tools to our usage.
I have made some progress, at the beginning, i have searched "No Connection", "Error 262", 1.03/1.03, xeno1 post was really helpful. So if i can help other forum members with same situation, it's great. I think that we are here for sharing knowledge and experiences.
Is there is a way to modify the topics subject ?
etron45 said:
Your tool WSS (Wizard Services Tool) is a great tool mestrini, it's more easier to use. A GUI is very helpful for a beginner than a text-based tool. Besides, lokiwiz is a great tool for the scene. Thanks for bringing these tools to our usage.
I have made some progress, at the beginning, i have searched "No Connection", "Error 262", 1.03/1.03, xeno1 post was really helpful. So if i can help other forum members with same situation, it's great. I think that we are here for sharing knowledge and experiences.
Is there is a way to modify the topics subject ?
Click to expand...
Click to collapse
Tx for the compliment
And yes, you can change the topic just by editing your first post and changing its title
Related
Hi,
I accidentally flashed a not CID unlocked wizard with Black Diamond rom using a ShellTool - now it loads only till windows splash screen!
It is G3 device - it allows to flash Buton rom, also MiniSrom and others - process bar goes to 100% but windows doesn't boot anyway!
What options do I have?
PS. I guess I'm one of the guy who have bricked the most devices ever - this one, 3x HTC Tytn, S200, etc.
Need QTEK 9100 German Rom - the wiki links are dead!
Can anybody please advise where to look for Qtek 9100 german rom?!!!
It is G3 device - it allows to flash Buton rom, also MiniSrom and others - process bar goes to 100% but windows doesn't boot anyway!
What options do I have?
Click to expand...
Click to collapse
Suche hilft wie immer weiter
Es gibt bereits einige Threads zum Thema!
Have a look for the SD Card Backup method - see also in the wiki for reference/link.
hi, thanks for the replay!
How does the SD card method is supposed to work? Do I need a backup of the old rom? I don't have one!
The phone is NOT cid unlcoked!
After a while playing with the Wizards I have found some things - I got 4 wizards by now - and I have managed to brick 2 of them.
First thing to recommend to all - if your Wizard is running and everything is fine - then don't upgrade - you don't need that brick. Trough if you try to upgrade and you can't get from wm5 to wm6 - then probably you should stop trying unless you want to brick your device totally!!!!
Now I have one Wizard G3 probaby not CID unlocked with IPL 1.01 / SPL 1.03 and different OS versions - I can flash button Rom, Wizard Love etc. but nothing changes, just the version of the OS. I have no GSM and the IPL stays 0.01.
The second one - seems to be CID unlocked - allows to flash any rom, IPL changes, SPL stays at 3.08 - can't downgrade, OS changes - can't boot!
I can flash these units forever, I can change bootscreens - but I can't get back to windows!
This happened when I tried to use ShellTool to flash WM6 on my Wizards - don't do that!!!!
Can anybody tell me why I'm not able to boot OS if I have the Wizard Love rom, button rom and other full working roms on my wizards?
Thanks!
PS. I'm starting to consider to donate a few devices to someone who could try to solve this - I could donate: 3 HTC Tytn, 2 Wizards, 2 Prophets, 2 Alpine etc. - is anybody interested?
karlux - I'd be willing to take a crack at the devices you have and get some good documentation going for everyone. I have successfully revived Wizards, Apache, Wallaby, and the Hurricane so far.
PM/Email me if you want my address to send the victims ...er ... I mean "patients".
donate? how about sending one my way?
karlux said:
After a while playing with the Wizards I have found some things - I got 4 wizards by now - and I have managed to brick 2 of them.
First thing to recommend to all - if your Wizard is running and everything is fine - then don't upgrade - you don't need that brick. Trough if you try to upgrade and you can't get from wm5 to wm6 - then probably you should stop trying unless you want to brick your device totally!!!!
Now I have one Wizard G3 probaby not CID unlocked with IPL 1.01 / SPL 1.03 and different OS versions - I can flash button Rom, Wizard Love etc. but nothing changes, just the version of the OS. I have no GSM and the IPL stays 0.01.
The second one - seems to be CID unlocked - allows to flash any rom, IPL changes, SPL stays at 3.08 - can't downgrade, OS changes - can't boot!
I can flash these units forever, I can change bootscreens - but I can't get back to windows!
This happened when I tried to use ShellTool to flash WM6 on my Wizards - don't do that!!!!
Can anybody tell me why I'm not able to boot OS if I have the Wizard Love rom, button rom and other full working roms on my wizards?
Thanks!
PS. I'm starting to consider to donate a few devices to someone who could try to solve this - I could donate: 3 HTC Tytn, 2 Wizards, 2 Prophets, 2 Alpine etc. - is anybody interested?
Click to expand...
Click to collapse
How come you have that many devices ? What's your job ?
Your "dead" wizard is not dead. Only stuck. Get it into bootloader and re-flash .
karlux said:
After a while playing with the Wizards I have found some things - I got 4 wizards by now - and I have managed to brick 2 of them.
First thing to recommend to all - if your Wizard is running and everything is fine - then don't upgrade - you don't need that brick. Trough if you try to upgrade and you can't get from wm5 to wm6 - then probably you should stop trying unless you want to brick your device totally!!!!
Now I have one Wizard G3 probaby not CID unlocked with IPL 1.01 / SPL 1.03 and different OS versions - I can flash button Rom, Wizard Love etc. but nothing changes, just the version of the OS. I have no GSM and the IPL stays 0.01.
The second one - seems to be CID unlocked - allows to flash any rom, IPL changes, SPL stays at 3.08 - can't downgrade, OS changes - can't boot!
I can flash these units forever, I can change bootscreens - but I can't get back to windows!
This happened when I tried to use ShellTool to flash WM6 on my Wizards - don't do that!!!!
Can anybody tell me why I'm not able to boot OS if I have the Wizard Love rom, button rom and other full working roms on my wizards?
Thanks!
PS. I'm starting to consider to donate a few devices to someone who could try to solve this - I could donate: 3 HTC Tytn, 2 Wizards, 2 Prophets, 2 Alpine etc. - is anybody interested?
Click to expand...
Click to collapse
Shelltool isn't dangerous if you use it properly, meaning you can't flash WM6 if the IPL/SPl are still in 1.xx
To use the SD card method and the phone is CID locked then i recommend using imeicheck's tool to CID unlock (must pay) and then try that method.
As for the donation, i wouldn't mind geeting a Prophet as they are related to the Wizard and in case it could be recovered i could try to make a similar tool to WST: the Prophet Service Tool
let me know if you'd like PM or other means of contact...
cheers
sorry-thread hijacking-
I have a similar problem, i (thought) i had CID unlocked my wizard, followed all the instructions, about reflashing the rom's went to 1.05 the to 2.26 & then IPL & SPL to 3.08 in an attempt to flash WM6..
all went well until the last step & it got to 99% of flashing WM6 & came up with a communication error (battery is fully charged!)
Now im stuck in bootloader, & can't re flash any other roms, tried the wizard with love & 1.05 again ...noting doing... have i made a complete brick ??
HELP!!!!!!!
edit, just tried with the O2 offical upgrade...it started to load on but came up with Error 296 Upgrade Only, the NBF file could not be used...
TRY THIS .... I just recovered from a similar stuck in BootLoader issue.
Steps to recovery:
1. Fully charge your phone (VIA Power Cord ... NOT USB)
2. Get the phone to bootloader (three color mode) - by soft resetting and holding the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Download your providers ROM (The "real" rom provided by Cingular/ATT). You can get the one for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
5. Stop ActiveSync (from Task Manager)
6. Run the program downloaded in step 4. This will reflash your phone with the ROM. This seems to be the ONLY WAY possible to reload a ROM from BootLoader.
Enjoy!
Thanks, i;ve tried that with this software & the o2 software....i get the same error message both times...
Error296 UPGRADE ONLY,
This NBF File cannot be used on you PDA Phone,
Please get a newer NBF file.
WTF is a NBF file, where do i get a newer one from & how do i get it on the device!!!
thanks
Zpyro said:
TRY THIS .... I just recovered from a similar stuck in BootLoader issue.
Steps to recovery:
1. Fully charge your phone (VIA Power Cord ... NOT USB)
2. Get the phone to bootloader (three color mode) - by soft resetting and holding the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Download your providers ROM (The "real" rom provided by Cingular/ATT). You can get the one for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
5. Stop ActiveSync (from Task Manager)
6. Run the program downloaded in step 4. This will reflash your phone with the ROM. This seems to be the ONLY WAY possible to reload a ROM from BootLoader.
Enjoy!
Click to expand...
Click to collapse
What is the make/model of your phone?
A nbf file is the file that gets flashed onto the phone (nk.nbf)
it was an xda mini s....i tried loading WM6 & came unstuck.....
huhu
karlux said:
Hi,
I accidentally flashed a not CID unlocked wizard with Black Diamond rom using a ShellTool - now it loads only till windows splash screen!
It is G3 device - it allows to flash Buton rom, also MiniSrom and others - process bar goes to 100% but windows doesn't boot anyway!
What options do I have?
PS. I guess I'm one of the guy who have bricked the most devices ever - this one, 3x HTC Tytn, S200, etc.
Click to expand...
Click to collapse
me too....!
markm2 said:
Thanks, i;ve tried that with this software & the o2 software....i get the same error message both times...
Error296 UPGRADE ONLY,
This NBF File cannot be used on you PDA Phone,
Please get a newer NBF file.
WTF is a NBF file, where do i get a newer one from & how do i get it on the device!!!
thanks
Click to expand...
Click to collapse
Hey!
I believe,as u have mentioned in ur earlier post that u have upgraded to ipl/spl 3.08,therefore all the official roms r not flashing.Well its not necessary to upgrade to ipl/spl 3.08 to go for wm6.All the experts & cooks in all their threads have mentioned to upgrade to ipl/spl 2.26 to have a stable/strong working plateform, so now I wud suggest u to plz try to flash Buttons's rom 1.05 and get back to ipl/spl 1.05 than onward upgrade to ipl/spl 2.26 by flashing t_mobile 2.26.
If u r able to get back to ipl/spl 1.05,than again use lokiwiz to confirm CID unlock,hope this works out. U can also use the latest WST tool by mestrini to check the status of ur wizzard as if its cid locked or unlocked.it can also be used to unlock cid,goodluck
zabardast_1 said:
Hey!
I believe,as u have mentioned in ur earlier post that u have upgraded to ipl/spl 3.08,therefore all the official roms r not flashing.Well its not necessary to upgrade to ipl/spl 3.08 to go for wm6.All the experts & cooks in all their threads have mentioned to upgrade to ipl/spl 2.26 to have a stable/strong working plateform, so now I wud suggest u to plz try to flash Buttons's rom 1.05 and get back to ipl/spl 1.05 than onward upgrade to ipl/spl 2.26 by flashing t_mobile 2.26.
If u r able to get back to ipl/spl 1.05,than again use lokiwiz to confirm CID unlock,hope this works out. U can also use the latest WST tool by mestrini to check the status of ur wizzard as if its cid locked or unlocked.it can also be used to unlock cid,goodluck
Click to expand...
Click to collapse
I just want to add that you MUST stop at 2.xx bootloader when downgrading from 3.08 to 1.xx, otherwise you might end up with a 'locked' SPL in 3.08
you need donate the device ....
I just want to add that you MUST stop at 2.xx bootloader when downgrading from 3.08 to 1.xx, otherwise you might end up with a 'locked' SPL in 3.08
YUP!!
Thanks Mestrini
very wise & valuable advise
Btw, very valuable tool it is WST TOOL,made our lives soooo simple
zabardast_1 said:
I just want to add that you MUST stop at 2.xx bootloader when downgrading from 3.08 to 1.xx, otherwise you might end up with a 'locked' SPL in 3.08
YUP!!
Thanks Mestrini
very wise & valuable advise
Btw, very valuable tool it is WST TOOL,made our lives soooo simple
Click to expand...
Click to collapse
Tx m8, that's why i made it and i'm glad you like it.
Im trying to CID Unlock my O2 Xda Mini.
I have followed all the steps below:
-connect your device
-Start hard_SPL-G4.exe
-Push the "Check DOC" button
-> The tool now checks whether your device is truly a G4, if not, it will give you an error and stops.
-> after this a dos box pops up, and it loads the softSPL to your device, to enable hard-SPL flashing.
-> then a Rom Update Utility will start, ONLY proceed if your screen is white!
-Proceed with the upgrade, it will only take a minute.
After reboot the IPL version is : 2.21.0001 and the SPL is 2.21.olip
But after rebooting I don't get the SPL 2.21.olip i get the original spl 2.21.0001
Thanks for any help
Go on boot loader and see if it sais anything different. Hard spl is only for flashing other roms by the way. Oh ye and can you give me the link to get hard spl plz. Thx
Within the past 2 hours, I have flashed 2 ROMS:
1. TNT.19199 Series V.2 (Offcial/Professional/TouchFLO) WM 6.1 Real Port
2. WM6.1 For Wizard OS 5.2.19521 buit 19521 WWE
I did a HardRest to T-Mobile ROM, connected to ActiveSync, went through the XP-ROMUpdate Utility until 100% completed, Clicked on Finished.
Saw the TNT Series It's Right with 2.26, 2.26, 2.25.11 and 2.26.10.2.
Then for some unknown reason the MDA restarted and came back up with the T-Mobile Hard Reset Screen and ask for a tap on screen, etc., to go through a total reset back to the T-Mobile ROM.
What did I do wrong?
Even after the T-Mobile ROM reset I still see the TNT Series It's Right with 2.26, 2.26, 2.25.11 and 2.26.10.2. screen but then my MDA is displaying the T-Mobile Today screen with the default Today stuff.
What do I need to do?
Thank you.
It sounds like your phone is not cid unlocked
Did you follow these steps for unlocking before flashing ??
http://forum.xda-developers.com/showthread.php?t=298613
Tonis said:
Within the past 2 hours, I have flashed 2 ROMS:
1. TNT.19199 Series V.2 (Offcial/Professional/TouchFLO) WM 6.1 Real Port
2. WM6.1 For Wizard OS 5.2.19521 buit 19521 WWE
I did a HardRest to T-Mobile ROM, connected to ActiveSync, went through the XP-ROMUpdate Utility until 100% completed, Clicked on Finished.
Saw the TNT Series It's Right with 2.26, 2.26, 2.25.11 and 2.26.10.2.
Then for some unknown reason the MDA restarted and came back up with the T-Mobile Hard Reset Screen and ask for a tap on screen, etc., to go through a total reset back to the T-Mobile ROM.
What did I do wrong?
Even after the T-Mobile ROM reset I still see the TNT Series It's Right with 2.26, 2.26, 2.25.11 and 2.26.10.2. screen but then my MDA is displaying the T-Mobile Today screen with the default Today stuff.
What do I need to do?
Thank you.
Click to expand...
Click to collapse
You are not CID Unlocked !
Read the sticky tutorial before you brick your device
...too slow
anichillus said:
You are not CID Unlocked !
Read the sticky tutorial before you brick your device
...too slow
Click to expand...
Click to collapse
Used WST V 0.4.0.0 and did a CID Unlock and received notification that CID Unlock completed. Do a Soft Reset which I did do.
Tried again to Flash both ROMS and they did show 100% competed/finished.
MDA softreset and showed both first screens of flashed roms, then went into Windows Mobile T-Mobile.
So, what did I do wrong?
This is the message I received after the CID Unlock:
All Done. CID Unlocking is finished and you
can now flash any ROM to your device.
All Done.
Don't forget to soft-reset device!!
A file with new CID value was created.
A backup file was created in program's
folder to restore to previous state.
This is other data:
Wizard Service Tool - 17 Mar 2008 19:00:36
CPU: Texas Instruments - OMAP850
MODEL: Wizard
IMEI: xxxxxxxxxxx
=> Bootloader (SPL):
Version: 2.26.0000 (G3 device)
Built on Jun 7 2006 at 19:18:46
Copyright (c) 2003 High Tech Computer Corporation
=> Firmware:
OS: 5.1 (Build 14955)
ROM: 2.26
Registry AKU: .2.3.0
Radio: 02.25.11
Protocol: 4.1.13.12
=>Extended_ROM:
Version: 2.26.10.105
Name: Extended_ROM
Status: hidden
=> Drives and partitions:
|--Handle--|---Size---|
ce9dc4a2 - 9.99M (0x9fd800)
aea9b13a - 48.23M (0x303c000)
efb23f92 - 50.95M (0x32f4000)
4fb23f3e - 2.94M (0x2f0000)
afb23fb6 - 3.06M (0x30fc00)
=> DOC chip unique ID:
00000000957802013300162f100c05be
Key Index: 8
JUST RECHECKED CID and this is what is shown:
Reading CID block...
Calculating CID block sum...
CID checksum: 23823E0A
Decrypted stored sum: 6705F27B786460AB
Decrypted calcd sum: 6705F27B786460AB
Key index : 8 - Block index: 128
CIDkey: MODULESN
CID IMEI: xxxxxxxxxxxxxxxxx
CID: WIZTMU01
Phone is CID LOCKED
So my phone is not CID Unlocked.
Where am I going wrong?
Thank you.
You didn't read the stickies carefully.
You need to flash the Button's ROM to have your IPL and SPL lowered to 1.01 before unlocking!
YUP !
It is must to have IPL/SPL 1.xx to CID unlock the phone,so read the sticky carefully and follow the method correctly.
Cheers!
Thank you both for helping me. I do agree that one should read very carefully. No excuses. However, there is so much to read and so many postings to read from. Again, I do appreciate your help and now I will find the T-Mobile Origirnal 1.xx ROM to load and go from there.
I will post this and I hope I do not get flamed. These are just suggestions from a new person. Please accept them as such.
1. Why did WST display that my MDA was CID Unlocked when it really was not? Should there be an edit up front to check for the correct IPL/SPL?
2. Why did both ROMs go through a complete cycle and then display that the ROM was completely flashed when it was not. Should there be an edit up front to check to ensure that the CID is Unlocked rather than go through all the install?
3. Why did both ROMS leave the splash screen on the MDA? Is there a way to get ride of them?
I know, read the threads before you take any action. Thank you both! You are right.
1.
CIDkey: MODULESN
CID IMEI: xxxxxxxxxxxxxxxxx
CID: WIZTMU01
Phone is CID LOCKED
WST does NOT show that it is unlocked...
2. Yes, there is checking in the Original RUU, all RUU in our custom WM6 ROMs are modified to bypass the checking. That's why it won't work if you try to flash another Carrier ROM to your Wizard without replacing the RUU program.
3. Just flash your original ROM (IPL+SPL 1.xx), unlock, and flash it again then you will get back the original splash.
starkwong said:
1.
CIDkey: MODULESN
CID IMEI: xxxxxxxxxxxxxxxxx
CID: WIZTMU01
Phone is CID LOCKED
WST does NOT show that it is unlocked...
(Not to disagree with you, but I did get a display that:
'This is the message I received after the CID Unlock:
All Done. CID Unlocking is finished and you
can now flash any ROM to your device.
All Done.
Don't forget to soft-reset device!!
A file with new CID value was created.
A backup file was created in program's
folder to restore to previous state.'
So, WST did display it CID UNLOCKED my MDA. That should be corrected in WST.)
2. Yes, there is checking in the Original RUU, all RUU in our custom WM6 ROMs are modified to bypass the checking. That's why it won't work if you try to flash another Carrier ROM to your Wizard without replacing the RUU program.
(I was addressing not the Original RUU, but the Flashing ROM that does not check or bypasses the checking. Would this help others if this edit was performed prior to executing the complete Flashing?)
3. Just flash your original ROM (IPL+SPL 1.xx), unlock, and flash it again then you will get back the original splash.
Click to expand...
Click to collapse
(Yes, I will do this. Thank you again for your help.)
Don't ever trust the successful message when you unlock CID (This is the same for using LokWiz02 also). Always perform CID check again after unlocking, that is the real status.
Cracking is not easy. Bypassing operations is relatively easy. Adding operations is very hard, so...
starkwong said:
Don't ever trust the successful message when you unlock CID (This is the same for using LokWiz02 also). Always perform CID check again after unlocking, that is the real status.
Cracking is not easy. Bypassing operations is relatively easy. Adding operations is very hard, so...
Click to expand...
Click to collapse
You are correct. One must never ASSUME that something is done. I wonder how many others have fallen into the same trap?
Latest status for me now is that I have:
IPL 1.08
SPL 2.26
01.0.9.10
2.26.10.2
So, I am back to the drawing board and trying to flash again. Tried WST and TNT and still did not take.
Maybe I am doomed to be with what is on the MDA.
Thank you again.
Tonis said:
You are correct. One must never ASSUME that something is done. I wonder how many others have fallen into the same trap?
Latest status for me now is that I have:
IPL 1.08
SPL 2.26
01.0.9.10
2.26.10.2
So, I am back to the drawing board and trying to flash again. Tried WST and TNT and still did not take.
Maybe I am doomed to be with what is on the MDA.
Thank you again.
Click to expand...
Click to collapse
There's no such trap,its just that the method is not correctly followed,either missing doing some step or doing a step incorrectly,resulting in not getting the things done correctly.
WST tool will not work in bootloaders ( multicolored screen) or in the splash screen stuck up.Secondly,TNT Rom is a wm6 rom,it won't flash or work with IPL 1.xx,it has to have IPL/SPL 2.xx and a CID unlocked phone.
after you flashed Button's Rom you got IPL 1.08 and SPL 2.26,reflash the Button's rom a couple of times more to make IPL/SPL 1.xx,it sometimes takes more then one flash to downgrade ipl/spl 1.xx,then apply lokiwiz02b to SIM/CID unlock the phone,upgrade to IPL/SPL 2.xx by flashing T-mobile 2.26 or official stock rom of your carrier AKU 2 Rom,only then upgrade to TNT series wm6 or 6.1 Rom.
Cheers!
zabardast_1 said:
There's no such trap,its just that the method is not correctly followed,either missing doing some step or doing a step incorrectly,resulting in not getting the things done correctly.
WST tool will not work in bootloaders ( multicolored screen) or in the splash screen stuck up.Secondly,TNT Rom is a wm6 rom,it won't flash or work with IPL 1.xx,it has to have IPL/SPL 2.xx and a CID unlocked phone.
after you flashed Button's Rom you got IPL 1.08 and SPL 2.26,reflash the Button's rom a couple of times more to make IPL/SPL 1.xx,it sometimes takes more then one flash to downgrade ipl/spl 1.xx,then apply lokiwiz02b to SIM/CID unlock the phone,upgrade to IPL/SPL 2.xx by flashing T-mobile 2.26 or official stock rom of your carrier AKU 2 Rom,only then upgrade to TNT series wm6 or 6.1 Rom. Cheers!
Click to expand...
Click to collapse
Well I finally flashed TNT 19199 Pro and it did install completely. I did use Button ROM which installed 1.08, 2.26.010.9.10 and 2.26.10.2. Then I used WST to CID unlock. Then I flashed TNT.
The main reason for me trying to flash a new ROM was that my MDA Touch Screen capability is very sporadic. It works some times, but not all the time. The only way I can get it to work after the Touch Screen is no longer touch sensitive, is to re-flash. I know that is not practical, but I want to try to resolve this Touch Screen problem.
Even after this latest Flash of TNT, I am still experiencing the same Touch Screen problem of not recognizing using the stylist.
Any suggestions? I assume that it is a hardware (MDA) problem and not a software (ROM) problem.
!!! USE THIS GUIDE ONLY IF YOU KNOW WHAT YOU ARE DOING !!!
!! READ THE END OF THE GUIDE FIRST(Very Importnat)
Aplication Unlock - lets you run unsigned software
SSPL - Software Second Program Loader is a boot loader after IPL (Initial Program Loader) often seen on smart phones and PDA:s.
- Lets you flash any rom on the phone
SPL 1.09 http://rapidshare.com/files/106089565/MTeoR_-_EUR1.09SPL.rar.html
[B]official HTC ROMS[/B]
RUS
http://rapidshare.com/files/106091396/RUU_MTeoR_1.34.261.1_1.38.00.10_HTCRUS_SHIP.rar.html
UNLOCK TOOLS
http://rapidshare.com/files/105133496/Unlock_HTC.rar.html
1. Folder "1"
put the file "SP_AllowCertificateInstall.cab" into the temp folder on you mobile phone (use active sync)
to connect. Execute the cab file on your phone.
2.Folder "2"
make sure you are connected to the phone threw active sync. Now run "EnableRAPI.bat" it will say if
it has succeded.
3.Folder "3"
make sure you are connected to your mobile phone through active sync. Start "MobileRegisteryEditor.exe"
Now go to SPV_C600 than HKEY_LOCAL_MACHINE than Security than Policies than Policies
so that you are in HKEY_LOCAL_MACHINE\Security\Policies\Policies
Now dubble click 00001001 (the first one after (Default)) and change the value to 1
Now dubble click 00001005 (the second one after (Default)) and change the value to 40
4.Folder "4"
put the file "Cert.cab" into the temp folder on you mobile phone (use active sync)
to connect. Execute the cab file on your phone.
5.Folder "5"
install and run HTC Security Manager.msi
select Security Off
Wait
YOUR PHONE IS APPLICATION UNLOCKED
6. Restart the phone
press and hold CAMERA+POWER while powering
you should see spl version
NOTE THAT VERSION
PULL OUT THE BATTERY AND POWER THE PHONE
7.1 Try to flash wwe rom directy
if you have wwe use sspl 1.01 http://forum.xda-developers.com/attachment.php?attachmentid=38680&d=1178637546
WWE rom
http://rapidshare.com/files/106091341/RUU_MTeoR_1.34.251.1_1.38.00.10_HTCEUR_SHIP.rar.html
after this you need to begin from step 1 till you see spl 1.10
now you have SPL 1.10 and CID HTC__Z12
jump to step 8
7.2 If 7.1 does not work try
7.2.1.SPL 1.09 http://rapidshare.com/files/106089565/MTeoR_-_EUR1.09SPL.rar.html
now you have SPL 1.10 and CID HTC__A07
7.2.2.you need to run the RUS update
RUS
http://rapidshare.com/files/106091396/RUU_MTeoR_1.34.261.1_1.38.00.10_HTCRUS_SHIP.rar.html
after this you need to begin from step 1 till you see spl 1.10
jump to step 8
8.flash any rom
now to flash an rom use SSPL 77.7 http://rapidshare.com/files/106072098/SSPL.rar.html
Copy the coresponding SSPL to the ROOT of the PHONE not the SD-CARD
run SSPL on the phone and immediatly press CAMERA+POWER
YOU SHOULD SEE TRI-COLOR SCREEN displaying spl 77.7
This SPL is allowing you to flash latest radio
or to Flash any rom usin sspl 77.7
Run the update from the PC
VERY IMPORTANT
i found a way to installl hardspl
1. unplug phone from usb
2. take out the battery/put it back
3. enter bootloader (press camera+power)
4. check for spl if it sais 2.05 you can go further if not read the fisrt guide
5. enter in windows
6. extract and copy to device root http://rapidshare.com/files/138396463/breeze_HARDSPL.rar.html
7. copy to storage card root BREEIMG.NBH
8. it should say SPL-1.01
9. follow onscreen instruction for the update
10.enter in windows and delete BREEIMG.NBH from card
11.enter bootloader (press camera+power)
12.it should say spl 7.77
13.be happy now you have hardspl and you can flash any rom (without sspl)
BEST REGARDS
i don't know whats the problem with appunlocking... there are 5 Regkeys that have to be set,... it stands all in wiki
http://wiki.xda-developers.com/index.php?pagename=Breeze_Registry
Application Unlock
http://wiki.xda-developers.com/uploads/Policies.reg
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"00001017"=dword:00000090"00001005"=dword:00000028"00001001"=dword:00000001after doing this run SDAunlock app (google for it) or
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101b"=dword:00000001
Running unsigned Apps without confirmation!
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101a"=dword:1
GREATLY APPRECIATED! finally some good explainations. so let me get this straight,
SSPL = application unlock? (im asking this because i already have my phone app unlocked using SDA security unlock software)
i have a dopod 595 and,
my IPL is 0.90 (do i need to update this?)
SPL is 2.05 (so i need to use the SPL>1.09)
radio is 1.06.00.10 (do i need to update this?)
RIL is 2.002
do i need to update anything before i try your WM6.1? which is the latest versions (IPL,Radio) you would recommend and can you please provide the links too. also, will the forward facing video call camera work with your ROM?
from wiki, it looks like there is the Radio:1.38.00.10 Protocol:32.71.7020.12H RIL:2.002 SPL:1.10.0000 ROM, and other older Radio ROMs but with newer SPL. so in order to update my radio, do i need to flash the entire ROM into my phone, or can i just use a Radio ONLY rom updater?
Please bear with me, because i really do not want to brick my phone.
Admin, please make this thread sticky. cheers
alexnvidia said:
GREATLY APPRECIATED! finally some good explainations. so let me get this straight,
SSPL = application unlock? (im asking this because i already have my phone app unlocked using XDA unlock software)
i have a dopod 595 and,
my IPL is 0.90 (do i need to update this?)
SPL is 2.05 (so i need to use the SPL>1.09)
radio is 1.06.00.10 (do i need to update this?)
RIL is 2.002
do i need to update anything before i try your WM6.1? which is the latest versions (IPL,Radio) you would recommend and can you please provide the links too. also, will the forward facing video call camera work with your ROM?
from wiki, it looks like there is the Radio:1.38.00.10 Protocol:32.71.7020.12H RIL:2.002 SPL:1.10.0000 ROM, and other older Radio ROMs but with newer SPL. so in order to update my radio, do i need to flash the entire ROM into my phone, or can i just use a Radio ONLY rom updater?
Admin, please make this thread sticky. cheers
Click to expand...
Click to collapse
i had 2.05 spl
i flashed the 1.09 spl from first topic
i flashed the latest wwe rom
now i have 1.10 spl
radio 1.38 from oficial rom
app unlocked
sspl
flashed wm6.1
jerpelea said:
i had 2.05 spl
i flashed the 1.09 spl from first topic
i flashed the latest wwe rom
now i have 1.10 spl
radio 1.38 from oficial rom
app unlocked
sspl
flashed wm6.1
Click to expand...
Click to collapse
im going to flash to WWE now with this version : HTC MUI BREE100 1.34.251.1 1.38.00.10 32.71.7020.12H 15673.3.3.1 3.3.1 2.002 1.10.0000 , then update to your WM6.1.
am i doing the steps right?
OK, i've done all the steps you provided in post no.1 (great instructions by the way). problem, when i run SSPL on the root of the device, the screen close blank and nothing happens even though im still pressing the camera+power button. what should i do now?
OK, i've done all the steps you provided in post no.1 (great instructions by the way). problem, when i run SSPL on the root of the device, the screen goes blank and nothing happens even though im still pressing the camera+power button. i had to unplug the battery to restart the device. am i doing anything wrong here?
Update : Now i got it. i had to run the SPL link, not the SSPL.exe as written in the first post. must be a typo.
Update2 : Success!! flashed to WWE. now proceeding to your WM6.1!!
Update3 : Running WM6.1 B1 now! thanks jerpelea! you're the man!
Admins please make this thread sticky.
I have I-Mate SPJas. I have tried several unlock tools including HTC Unlock toll, resgistry edit, SDA Unlock....
My original SPL version was 2.05 and after I ran SPL file I had IPL=SPL by des and SPL=7......
I have also applied other methods and my phones seems to be application unlock. But when I try to upload a new rom the phone goes to blank. I could never prevent this condition.
Is there a way to update Imate SPJas to Win 6.1? Which ROM works?
caglar_altan said:
I have I-Mate SPJas. I have tried several unlock tools including HTC Unlock toll, resgistry edit, SDA Unlock....
My original SPL version was 2.05 and after I ran SPL file I had IPL=SPL by des and SPL=7......
I have also applied other methods and my phones seems to be application unlock. But when I try to upload a new rom the phone goes to blank. I could never prevent this condition.
Is there a way to update Imate SPJas to Win 6.1? Which ROM works?
Click to expand...
Click to collapse
all roms work
follow the guide and will work
rom
I have gone through all of the steps of ROM update.
When the rom update utility prepare for installing, after I press "ENTER" the device closes immediately and the connection with ActiveSync stops.
In three color screen I see:
IPL SSPL by des
SPL : 1.01
Enter
When I go through root directory and enter to SSPL.exe, the phone again shut down and I have to removE/install battery to start the phone.
Please help!!
caglar_altan said:
I have gone through all of the steps of ROM update.
When the rom update utility prepare for installing, after I press "ENTER" the device closes immediately and the connection with ActiveSync stops.
In three color screen I see:
IPL SSPL by des
SPL : 1.01
Enter
When I go through root directory and enter to SSPL.exe, the phone again shut down and I have to removE/install battery to start the phone.
Please help!!
Click to expand...
Click to collapse
Hi, I had the same issue. Try pressing camera & off' buttons AND Enter all together.
rom update
1- I have updated the current rom to origininal config by manufacturer's original ROM.
2- I applied HTC unlock tool..
3- My first attempt to update rom gave #262 error. Second attempt was succesful.
thanks.
futureshock said:
i don't know whats the problem with appunlocking... there are 5 Regkeys that have to be set,... it stands all in wiki
http://wiki.xda-developers.com/index.php?pagename=Breeze_Registry
Application Unlock
http://wiki.xda-developers.com/uploads/Policies.reg
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"00001017"=dword:00000090"00001005"=dword:00000028"00001001"=dword:00000001after doing this run SDAunlock app (google for it) or
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101b"=dword:00000001
Running unsigned Apps without confirmation!
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101a"=dword:1
Click to expand...
Click to collapse
there are 5 keys unless you have the official security configuration manager
that is setting the other keys for you
BR
HARDSPL
hy all
i found a way to flash hardspl to breeze
this will allow to flash any rom from any cid so that you will not break devices due to wrong cid
BR
is there anyway to hard spl without going into windows? my device is stuck at windows 2nd boot screen (windows mobile 5 logo)
jerpelea said:
hy all
i found a way to flash hardspl to breeze
this will allow to flash any rom from any cid so that you will not break devices due to wrong cid
BR
Click to expand...
Click to collapse
That sounds interesting..!
alexnvidia said:
is there anyway to hard spl without going into windows? my device is stuck at windows 2nd boot screen (windows mobile 5 logo)
Click to expand...
Click to collapse
no
you must get to windows
what is your current cid?
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine. then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
alexnvidia said:
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine. then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
Click to expand...
Click to collapse
you can not do anithing
your ipl does not know how to load spl1.09
send the phone to repair and flash hardspl when it returns
there are many people with your problem
till now we have found not found any solution
BR
my phone is out of warranty, so sending for repair will cost me a lot. we'lll keep our fingers crossed and hope you guys can find a solution for us soon. thank you
i think, SPL version is very confusing. 2.05 is older than 1.09?
Would be good to have compatibility list between SPL and IPL versions to not mess and brick device.
I guess i was lucky, because i updated my breeze to resently posted HardSPL (thanks to jerpelea) and device still alive.
I found that RUUUpdateUt.exe i've used for DES SoftSPL is not working with HardSPL anymore. It cost me a bunch of my nerves (no body mentioned this fact!). Again luckily i found that stock RUU upgrade utility works fine with HardSPL (i just removed all dialogs except first for convenient use).
Well, at last, now i don't need to flash stock firmware (with radio ROM update which is extremely dangerous) every time when one of my cooked ROM refuses to work normally.
Needed
1.an BREEZE device[The phone must be able to enter bootloader (3color screen)]
2.TerraTermPro http://rapidshare.de/files/39206549/TeraTermPro.rar.html
3.An rom matching to your device
GUIDE
1.Disable active sync - uncheck
file->connection settings->allow usb connection
2.Put the phone in bootloader mode
power the phone pressing power and camera keys
read and note all displayed info
3.Launch TerraTermPro on the pc
un the connection window check serial and choose USB
in the new open window type
info 2
and note the information
RIGHT - HTCSQTEK_A07„§m»HTCE
WRONG - HTCSF kEØ(HTCE
close terra term
4.Figure out wich rom you need
till now i have roms for
Russian Rom
QTEK_A07
HTC__A07
http://rapidshare.com/files/109782599/RUU_BREE100_1.34.261.1_1.38.00.10_HTCRUS_SHIP.rar.html
WWE Rom (QTEK,HTC,Dopod,OCH)
QTEK_Z12
HTC__Z12
http://rapidshare.de/files/39206931/RUU_MTeoR_1.34.251.1_1.38.00.10_HTCEUR_SHIP.rar.html
DOPOD001 - Chinese Rom
http://www.megaupload.com/se/?d=YD49L7JD
5.
Flash the rom corresponding to your CID
6.
Boot the phone and application unlock it
7.
Run SSPL and UPGRADE to 6.1 rom and latest radio version
8.
Save the rom that saved you for latter - it colud help you again
IF YOU CANT FIND THE CID AND ROM HERE WAIT TILL SOMEBODY POSTS IT.
IN CASE OF "HTCSF kEØ(HTCE" IN TERRATERM IS VERY HARD TO REPAIR DUE TO DAMAGED BOOTLOADER
you can repair it using this guide
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
wich requires some advanced skills
OTHER ROMS - wich i dont have
i_mate_SP_JAS_1.15.301.0.exe
RUU_BREE100_1.15.71.6_1.06.00.00_OCH_Ship.exe
ruu_bree100_1.15.707.3_dopodwwe_ship.exe
ruu_bree100_1.15.709.3_dopodcht_ship.exe
Please help me to improve this list sending me CID's and ROM's
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
what do you mean by very hard to repair? it's impossible?
this is the ROM i flashed back to my phone (although the flashing is 100% completed successfully, it is still stuck at 2nd boot WM logo screen)
RUU_BREE100_1.15.707.3_DopodWWE_SHIP.exe
i just uploaded th dopod rom in case anyone needs it
http://rapidshare.com/files/109798242/RUU_BREE100_1.15.707.3_DopodWWE_SHIP.exe
alexnvidia said:
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
what do you mean by very hard to repair? it's impossible?
this is the ROM i flashed back to my phone (although the flashing is 100% completed successfully, it is still stuck at 2nd boot WM logo screen)
RUU_BREE100_1.15.707.3_DopodWWE_SHIP.exe
i just uploaded th dopod rom in case anyone needs it
http://rapidshare.com/files/109798242/RUU_BREE100_1.15.707.3_DopodWWE_SHIP.exe
Click to expand...
Click to collapse
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
use this wisely
jerpelea said:
http://wiki.xda-developers.com/index.php?pagename=PB_KITL_HERMES
use this wisely
Click to expand...
Click to collapse
how do i put breeze into KITL Mode? is it the camera+power button tri-colour thing?
reads what stands on hermes wiki page...
maybe i'm talking ****, but i think too enter kitl mode you must have a running windows mobile...
just find the kitl mode "reset" on hermes its "now for your Hermes: hold the Comm button and soft reset and wait for the KITL dialog to appear, now is the CRITICALLY missed step; you need to press the small OK button on the LEFT of the device to activate USB KITL. "
futureshock said:
reads what stands on hermes wiki page...
maybe i'm talking ****, but i think too enter kitl mode you must have a running windows mobile...
just find the kitl mode "reset" on hermes its "now for your Hermes: hold the Comm button and soft reset and wait for the KITL dialog to appear, now is the CRITICALLY missed step; you need to press the small OK button on the LEFT of the device to activate USB KITL. "
Click to expand...
Click to collapse
exactly.. that's the worrying part for me now. i have no idea how do i enter KITL mode in breeze. any ideas?
alexnvidia said:
exactly.. that's the worrying part for me now. i have no idea how do i enter KITL mode in breeze. any ideas?
Click to expand...
Click to collapse
no
i did this on my hermes once
having the same problem as you have on breeze
hermes and breeze share the same platform
we have to find the answer
How did you manage to screw the bootloader
can you provide us a list of what you have flashed on the device?
what is the brand,model(herm 100/herm160),vendor,region of your device
i am triing to figure an solution
all others upgraded succesfully to 1.34 rus getting HTC__A07 CID and after that radio and wm 6.1
what did you do ?
BR
jerpelea said:
no
i did this on my hermes once
having the same problem as you have on breeze
hermes and breeze share the same platform
we have to find the answer
How did you manage to screw the bootloader
can you provide us a list of what you have flashed on the device?
what is the brand,model(herm 100/herm160),vendor,region of your device
i am triing to figure an solution
all others upgraded succesfully to 1.34 rus getting HTC__A07 CID and after that radio and wm 6.1
what did you do ?
BR
Click to expand...
Click to collapse
ok. i have no idea hoiw i screwed up the bootloader too. this is what happens.
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine. then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
what should i do now? i really appreciate you/anyone taking the time to look into this issue. thank you.
have you tryed a hardreset??
and did you cid is now screwed up??
alexnvidia said:
ok. i have no idea hoiw i screwed up the bootloader too. this is what happens.
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine.
Click to expand...
Click to collapse
here you needed the sspl to flash official rom
i think that i have this im my tread
then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
Click to expand...
Click to collapse
here you screwed the botloader
now you have an older ipl that does not know how to load the new SPL
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
what should i do now? i really appreciate you/anyone taking the time to look into this issue. thank you.
Click to expand...
Click to collapse
did you try to hard reset?
the two "-" keys and power
???
futureshock said:
have you tryed a hardreset??
and did you cid is now screwed up??
Click to expand...
Click to collapse
yes. i tried hard reset (two soft keys+power then press 0) many times. doesnt work. tried the mtty to format the phone, doesnt work.
here you screwed the botloader
now you have an older ipl that does not know how to load the new SPL
ok, firstly, when i loaded up the SPL1.09, the phone boots up fine. it only got stuck when the flashing to WWE1.38 failed. at this point i still have the new IPL.
the old IPL was flashed in during the recovery attempt when i tried to flash the old official WM5 ROM back hoping it would also downgrade the SPL, but it didnt. it only downgrade the IPL to 0.9. SPL remains 1.09
alexnvidia said:
here you screwed the botloader
now you have an older ipl that does not know how to load the new SPL
ok, firstly, when i loaded up the SPL1.09, the phone boots up fine. it only got stuck when the flashing to WWE1.38 failed. at this point i still have the new IPL.
the old IPL was flashed in during the recovery attempt when i tried to flash the old official WM5 ROM back hoping it would also downgrade the SPL, but it didnt. it only downgrade the IPL to 0.9. SPL remains 1.09
Click to expand...
Click to collapse
im my guide i wrote to use sspl
if you use sspl you finish the 1.34 upgrade from spl 1.09 and is everything fine
if not no
from here you had spl A07 so you could flash ONLY original htc Rus rom
you flashed an older ipl instead
an older ipl that does not load correctly the new spl
the spl can not be downgraded from 1.10(1.09) to 2.05
here is the problem
and as long as you dont have an rom with your CID od HARDSPL the phone can only be flashed using my hermes guide if we find the buton combination on breeze
BR
jerpelea said:
im my guide i wrote to use sspl
if you use sspl you finish the 1.34 upgrade from spl 1.09 and is everything fine
if not no
from here you had spl A07 so you could flash ONLY original htc Rus rom
you flashed an older ipl instead
an older ipl that does not load correctly the new spl
the spl can not be downgraded from 1.10(1.09) to 2.05
here is the problem
and as long as you dont have an rom with your CID od HARDSPL the phone can only be flashed using my hermes guide if we find the buton combination on breeze
BR
Click to expand...
Click to collapse
so what you mean now is my IPL 0.9 is WWE and my SPL is 1.09 Qtek A07? and this is causing the problem? so can i flash the IPL on the phone to the lastest one in tri-colour mode so that it can read the 1.09 SPL? can u please provide me with the SPL upgrade file and utility?
any solutions so far? guys?
alexnvidia said:
so what you mean now is my IPL 0.9 is WWE and my SPL is 1.09 Qtek A07? and this is causing the problem? so can i flash the IPL on the phone to the lastest one in tri-colour mode so that it can read the 1.09 SPL? can u please provide me with the SPL upgrade file and utility?
Click to expand...
Click to collapse
no
your problem is that ipl 0.9 cant load spl 1.09
the memory load address differs and it cant load it correctly
i havent found an solution
you need an valid spl loaded to flash
you can try all the original roms (don't edit them)
and see if any one of them tries to push ipl and spl before actualy flashing
also try the official 1.09 spl flash
BR
nowaday, I found this thread useful. thanks
what happened? I was upgrading to futureshock ver. 4 and during phone'd swiched off ... I was looking for original ROM posted here in Breeze forum, but I didn't find it ... after read this 1st post I recoginze, that Czech ROM official is RUS .. that news for me (of course good ).
KITL Hermes
I had ROM 6.1 from Futureshock...still problem with radio (my phone couldn´t accessble but signal icon shows good signal, radio version 1.38.0000), so I decided flash some original ROM. Aftet that my booting stuck on HTC logo or Windows Mobile logo. So I can´t use normal way to flashing. Only from SD card or first turn on phone to boot loader mode and than attach usb cable and start flashing. From SD card (where is renamed ROM BREEIMG.NBH) after enter into bootloader mode start loading and than just turn to trhreecolour menu where is BREE100 - IPL-0.90 and BREE100-1.10.0000 and doesn´t want continue. If I flash ROM via USB cable (first go to threecolour mode, than attach cable) than run ROMUpdateUtility.exe and flash process is being started but always die on 2%, than autoreboot and again stuck on HTC logo.
I tried hard reset, I tried lot of ROM versions HTCRUS, HTCEUR, QTEKEUR, FUTURESHOCK but still same problem during flash ROM stop on 2%...
I tried KITL Hermes unbrick method but same problems like had others on this forum, I don´t know how to turn my MTeoR to KITL debug mode because device is different like Hermes so key combination doesn´t matches with Breeze. MTTY - info 2 command show me CID: waiting interpreter failed...
Any ideas how to back life to my MTeoR?
Can I use application like MTTY? Could me help this program?
Thanks for any help...
DOPOD601
which RUS update rom can i use?thanks
HTCSDOPOD601in眘HTCE
which rom?
can somebody email to : [email protected] or [email protected] ?
thank you