Related
Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
My Wizard was almost bricked at that time and after I speak with an I-mate technical guy, I got the following:
1. Make sure your i-mate™ K-JAM is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your i-mate K-JAM to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
Hope it helps!
this realy worked for my (ex)bricked dutch tmobile mda vario !!!!
tip: REALY make shure that there is no wcescomm.exe running all the time and realy remove the sd card else is nogo
btw: my wizard is CID locked! and works like a charm
Thanks buddy!
I'm happy that worked for ya!
Take care!
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Hi!
Have you already flashed your device once?
Which ipl/spl do you have?
I had problems over 1.05 ROM in the beggining.
If you stuck on bootloader mode, that's a good signal your device is not bricked.
I'd recommend you to disable activesync as you did and reflash it again! Check also if your device is CID unlocked! Search for a thread in the xda developers root.
Try to upgrade to ipl/spl 2.26 first and later to others you want.
Regarding the old file error...can be related to a missing file called enterbootloader.exe.
Hope it works for ya!
Take care
Ironman273 said:
I'm having a problem
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Any ideas?
Click to expand...
Click to collapse
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Sounds great to hear that!
I had play around with pdaviet3, underground and another ROM just today without any problems at all. I don't think that this is the case. Now you get your device back to normal, try to reflash it again. Hope it works this time!
BTW,...São Paulo is a nice city. Thanks! Let me know if you decide to come here!
Take care
Ironman273 said:
My device is unlocked as I've been trying different ROMs as of late. I had gone back to the Cingular 2.25 ROM for a couple days to sort some things out and was going to flash Farias AKu 3.3 when my power problems happened. My Current IPL/SPL is 2.25
I've tried flashing the TMobile 2.26 but keep getting connection errors. In fact, I've tried flashing with every ROM I have pdviet 3 and 4, CIngular 2.25, TMobile 2.26 and Custom 1.05. Everything (except twice in the custom) gives me connection errors.
Any other trick I can try?
BTW, I used to live in Sao Paulo years ago...
Edit: OK, so I tried the 2.26 TMobile ROM after I typed this and it worked!! I'm back up but I was having trouble with that ROM beause of some incompatibilities with Cingular. I'll go back to Cingular's ROM and play it safe for now.
I believe part of my problem was I kept trying different updates one after the other. Now that I think back, the 2 times I got the update to almost work was after I turned off the device and turned it on again, which is what I did this time around also.
Click to expand...
Click to collapse
It seems you got the idea!
You did the right thing! Sometimes, use the official ROM can solve many issues out there!
Keep walking!
enlite_de said:
I had the same problems as mentioned by Ironman before. I followed the steps and with a few slight changes, I managed as well to "unbrick" my wiz. THANKS A LOT for the great step by step manual!!!
Still I wanted to know WHY i bricked my device:
I was trying to upgrade to the underground WM6 ROM. I got the same situation as ironman:
Quote:
The power went out as I was upgrading my Wizard (Cingular) so now it just turns on at the boatloader screen. I've tried running updates while it was in this screen (it did show the "USB" in the white bar) but most of the time it tells me there is a connection error. Even if I kill Activesync, I notice that when I run the update utility it still runs Activesync. I've tried disabling the USB connection but still get the connection error.
The only time I haven't gotten the connection error was twice it asked me to update but then told me I had the wrong file. This only happened when I tried "upgrading" to 1.05 as I was trying to start again. After it tells me that if I try running it again it gives me the connection error.
Unquote
I then followed the instructions by epimazzo as written above. I also tried the T-Mobile ROM 2.26 which was not working for me. PANIC!!!! Error messag was that I had the wrong Vendor ID. THerefore no upgrade to TMob 2.26 was possible. I tried it then my original qtek ROM in my language and see it worked!!! This IMHO means that I did not put the device in a proper IPL1.xx and SPL 1.xx status which is required for a clean system in irder to unlock it! So if it is bricked, try your native AKU2 ROM and make sure you unlocked it properly. Maybe you have to run the 1.05 ROM for a second time after the unlocking.
I hope this helps you guys.
Click to expand...
Click to collapse
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
In my opinion this thread is so helpful to people who brick their device, it should go "sticky". Mods anything you can do about it?
Thanks buddy! I really appreciate!
We survive here over tips like that!
jt_armstrong said:
Excellent post. I messed up with my own cooked ROM and could only get the bootloader screen. Tried the tips here - didn't work first time but I pulled the battery from the KJAM to reset it rather than using the reset button and it worked fine.
Click to expand...
Click to collapse
Help me similar problem
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Hi there!
It seems that you just need to enter into the bootloader mode and reflash it again!
I had similar problems and more during my brick "false" stage!
So, just try to follow my steps here and you should be fine! Once you get into bootloader mode, just use any ROM out there to reflash.
Good [email protected]
thaiphong said:
I upgraded Super Rom, then my Wizard run very slow and no signal (no call out and in- no network at all). And Terible thing is PC could not dectect PPC thought Active Sync. I've soft and hard reset but no use.
So I donot know where to start to re install Rom again.
Please help me....
Click to expand...
Click to collapse
I was about to start a EMERGENCY HELP thread, but I *think* this is the right place instead.
The "touch" of my screen went dead today. It got progressively worse over a few hours, starting with difficulty in using the phone dialer, then random incorrect stuff getting triggered by screen taps.
So I hard reset, and got no response on the fifth alignment cross, meaning 1) "Tap on the screen...; 2) center; 3) top left; 4) bottom left; 5) bottom right. In that I could not proceed with alignment, I hard reset again, and now, at the first alignment screen, i.e. "Tap on the screen...", I have no screen response at all.
I called T-mo, and they are being great about sending a replacement ASAP (and getting me a loaner in the meantime).
BUT, I am running Faria+ AKU3.3 V2... so I clearly have to flash back to T-mo 2.26. I can;t figure out how to do it though, as no matter what I do I am stuck at the first alignment screen!!
HELP!! EMERGENCY!!!
(I have three or four days to get this done, so it's not THAT urgent)
Do a search for Broken Screen. Someone (either in Wizard Upgrading or in the Wizard forum) just had a similar issue with a cracked screen. They downloaded something that allowed them to get around the welcome page.
Actually, if you are just trying to flash a new ROM, don't even mess with it. Go straight to the Boot Loader screen (see the first post of this thread). No tapping necessary until the new rom is on (and that will be the Tmobile then so you would be good.
Thanks for the quick reply. Charging up to green now, and then will try to enter bootloader and flash T-mo 2.26. Will report back.
Worked great. Back to T-mo she goes!!!
BootLoader Mode
Excellent thread but you left out one thing.....exactly how to place your device in bootloader mode.
To clear up any misunderstanding because this is very important....this is how you do it:
Perform a soft reset, when the screen goes blank hold the camera button until a multi colored screen comes up .... That's it !!!!!!
When the unit is connected, USB is displayed at the bottom left.
[SOLVED! See page 4]
I have a Cingular 8125, which I hadn't used for a while (got a Trinity
I am trying to set it up for my wife, so I attempted to unlock it and upgrade to WM6. It is a G3 (it had 2.26). I had upgraded it several times before. but was never able to bring it down to 1.xx in order to unlock it.
So, I started trying to downgrade it, but basically, every time it entered bootloader, it seemed to lose connection and it just timed out on the PC, without ever going to the update bar on the bootloader screen.
I ran IPL_SPL_3.08, and it upgraded fine. But still no go on downgrading.
Finally, I ran Shelltool (bug fixed) and managed to flash to OS 1.5.4.2. But, after the hard reset, it just stays on the blue Cingular screen (showing IPL 3.08; SPL 3.08; GSM 02.47.11; OS 1.5.4.2.)
I have tried flashing again with an original Cingular WWE ROM (RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe), with the 1.5.4.2 ROM, even with a WM6 ROM (again, through Shelltool.) I have placed it in a powered cradle, have tried both Shelltool and RUU flashes, both while in the blue Cingular screen, and while in Bootloader mode. I have disconnected and reconnected each time, and rebooted many times (both the Wizard and the PC.) I have hard-reset. I have also tried both with USB selected and unselected in Activesync.
The Shelltool seems to freeze. The official RUU gives "ERROR [296]: UPGRADE ONLY. The NBF file cannot be used for your PDA Phone. Please get another NBF file." Or, alternately, it gives "ERROR [264]: CONNECTION."
Any ideas if this is repairable?
(Or should I cry (or take a hammer to the Wizard:-((
Mine is a 2.25 and it's a G4.. Isnt 2.26 a G4?
I think it was 2.26 (it may have been something like 2.27....), but it definitely didn't have the .000 at the end. I thought that the Wizards without the .000 were G3. Did I screw up?
Madcap180 said:
Mine is a 2.25 and it's a G4.. Isnt 2.26 a G4?
Click to expand...
Click to collapse
2.25.0001 or 2.26.0001 would be a G4
2.25 or 2.26 would be a G3
MacGuy2006 said:
I have a Cingular 8125, which I hadn't used for a while (got a Trinity
I am trying to set it up for my wife, so I attempted to unlock it and upgrade to WM6. It is a G3 (it had 2.26). I had upgraded it several times before. but was never able to bring it down to 1.xx in order to unlock it.
So, I started trying to downgrade it, but basically, every time it entered bootloader, it seemed to lose connection and it just timed out on the PC, without ever going to the update bar on the bootloader screen.
I ran IPL_SPL_3.08, and it upgraded fine. But still no go on downgrading.
Finally, I ran Shelltool (bug fixed) and managed to flash to OS 1.5.4.2. But, after the hard reset, it just stays on the blue Cingular screen (showing IPL 3.08; SPL 3.08; GSM 02.47.11; OS 1.5.4.2.)
I have tried flashing again with an original Cingular WWE ROM (RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1.exe), with the 1.5.4.2 ROM, even with a WM6 ROM (again, through Shelltool.) I have placed it in a powered cradle, have tried both Shelltool and RUU flashes, both while in the blue Cingular screen, and while in Bootloader mode. I have disconnected and reconnected each time, and rebooted many times (both the Wizard and the PC.) I have hard-reset. I have also tried both with USB selected and unselected in Activesync.
The Shelltool seems to freeze. The official RUU gives "ERROR [296]: UPGRADE ONLY. The NBF file cannot be used for your PDA Phone. Please get another NBF file." Or, alternately, it gives "ERROR [264]: CONNECTION."
Any ideas if this is repairable?
(Or should I cry (or take a hammer to the Wizard:-((
Click to expand...
Click to collapse
I thought I read somewhere that IPL/SPL 3.08 was a bad convert from a Charmer? If this is true and the Charmer bootloaders are different than the Wizard bootloaders then you may have put yourself in a bind.
The fact that you can still get past bootloader is promising even though the phone doesn't finish booting.
Try flashing from the bootloader (tricolor IPL/SPL screen with USB in the corner)
Thanks. I've been trying to flash in both bootloader or "blue" screen, but no go so far. I just tried the official Cingular .nbf through shelltool: it spent about 30 minutes (in bootloader,) then it stopped responding. It's been doing this forever now.
Any other options left?
MacGuy2006 said:
Thanks. I've been trying to flash in both bootloader or "blue" screen, but no go so far. I just tried the official Cingular .nbf through shelltool: it spent about 30 minutes (in bootloader,) then it stopped responding. It's been doing this forever now.
Any other options left?
Click to expand...
Click to collapse
You CAN'T use shelltool in boot loader mode! it needs the OS and the TRUFFS to read and write to the phone.
Any phone that doesn't go past the boot loader must be fixed with mtty, RUU or SD card...
Thanks for the info. I've been reading about mmty and just downloaded it. But I only have a 4GB card handy (from my Trinity.) I might be able to find my old 2GB one at home.
Edit: Well, this is what I just found: http://forum.xda-developers.com/showthread.php?t=308772&highlight=mtty+wizard
It seems that the IPL_SPL 3.08 might be a real problem. I'll try the card flash, but based on the above thread, I am not holding my breath.
If anyone has a suggestion or a solution, please let me know.
Thanks!
BTW, if the problem is indeed with the IPL_SPL 3.08, then perhaps the suggestion that we upgrade to it (in red) here http://forum.xda-developers.com/showthread.php?t=285435 should be removed, so that we don't get more expensive bricks.
Just to clear up the question about 3.08 IPL/SPL, it isn't an issue at all. It's been tested thoroughly to work well, better than 2.26.
TaurusBullba said:
Just to clear up the question about 3.08 IPL/SPL, it isn't an issue at all. It's been tested thoroughly to work well, better than 2.26.
Click to expand...
Click to collapse
After I unlocked my wizard and before I try any new ROM, I always burn the latest German wizard ROM with 3.08 IPL/SPL "ruu_vario_aku3.3_3822_382120_026911_tmo_de_ger_ship". Then I downgrade the Radio ROM to Cingular 2.25.11. Then I burn my ROM of choice. I've found it works best for me. I've never had a problem with 3.08.
TaurusBullba said:
Just to clear up the question about 3.08 IPL/SPL, it isn't an issue at all. It's been tested thoroughly to work well, better than 2.26.
Click to expand...
Click to collapse
What are the grounds for such a comparison? How to tell that an SPL works better than another? As far as i know the SPL is there to initialise the hardware and to apply security restrictions.
What i'd like to know is if anyone has been successful in downgrading IPL/SPL from 3.xx to 2.xx as itsme once said that there was a security in newer SPL's preventing downgrading (i must look for it...)
cheers
O.K., so maybe it's not 3.08, but something has sure gone bad.
I am trying to use mtty 1.1.42.538, but see only Port 1, Port 2 and USB. When I type in \\.\WSCUSBSH001 I get a message that it cannot open the \\.\WSCUSBSH001 port.
I tried resetting as described in message #7 here http://forum.xda-developers.com/showthread.php?t=264652&highlight=mtty1.42, but nothing happened.
I also tried choosing USB, then typed in r2sd all and again, nothing happened - I just get CMD> again....
So, can anyone think of anything else I can do, or should I just drop it from the 4th floor?
What IPL/SPL values you have at this moment?
mestrini said:
What IPL/SPL values you have at this moment?
Click to expand...
Click to collapse
Both ar 3.08, and I have the feeling that this is why I cannot flash the official Cingular ROM over what I have now. Which makes me wonder: is there an official Wizard ROM file combined with the IPL/SPL 3.08? This may at leas allow me to flash.
MacGuy2006 said:
Both ar 3.08, and I have the feeling that this is why I cannot flash the official Cingular ROM over what I have now. Which makes me wonder: is there an official Wizard ROM file combined with the IPL/SPL 3.08? This may at leas allow me to flash.
Click to expand...
Click to collapse
I had also upgraded my IPL/SPL to 3.08 -- up from the 2.25 on the newest Cingular ROM.
Anytime I've flashed to a WM6 ROM, I've been able to downgrade to the T-Mobile 2.26 ROM -- which changes the IPL/SPL to 2.26 -- with no problems before upgrading to a WM6 ROM. After flashing the WM6, I then go back in and upgrade the IPL/SPL once again to 3.08. It's not failed me yet.
O.K., I've spent the weekend screwing around with this:
If I run any of the original 2.xx ROMs, I get "you need an updated utility" message and then the utility goes to the "Exit" screen. (I am assuming this is because of the 3.08 IPL/SPL.)
mtty tells me I don't have permissions when I tried to load the ROM on a SD card (remember, the 8125 is not SuperCD-ed.). It also does nothing when I type "set 14 0" or "task 28."
But, I found that I can run the XDA Mobile 6 ROM (http://forum.xda-developers.com/showthread.php?t=310954) and it actually starts updating, but when it gets to 99%, the bar on the 8125 turns red and after a while the Update Utility tells me that the Wizard is not connected anymore.
Got very excited when I tried mattk_r's InGeNeTiCs' ROM(http://forum.xda-developers.com/showthread.php?t=311144): it started updating, went all the way to 100%, at which point the bar on the 8125 did turn red, however after a period of time the utility gave me the "Congratulations" message and told me I've successfully upgraded. But then, the 8125 reboots, and unfortunately, it still hangs on the boot screen, and it still gives the OS as 1.5.4.2. Have tried a number of times, always the same:-(
Oh, I tried upgrading the Radio only, and it worked: I was able to upgrade to 02.61.11.
So, does it seem like there is hope, and can anyone think of what else I can do?
MacGuy2006 said:
O.K., I've spent the weekend screwing around with this:
If I run any of the original 2.xx ROMs, I get "you need an updated utility" message and then the utility goes to the "Exit" screen. (I am assuming this is because of the 3.08 IPL/SPL.)
mtty tells me I don't have permissions when I tried to load the ROM on a SD card (remember, the 8125 is not SuperCD-ed.). It also does nothing when I type "set 14 0" or "task 28."
But, I found that I can run the XDA Mobile 6 ROM (http://forum.xda-developers.com/showthread.php?t=310954) and it actually starts updating, but when it gets to 99%, the bar on the 8125 turns red and after a while the Update Utility tells me that the Wizard is not connected anymore.
Got very excited when I tried mattk_r's InGeNeTiCs' ROM(http://forum.xda-developers.com/showthread.php?t=311144): it started updating, went all the way to 100%, at which point the bar on the 8125 did turn red, however after a period of time the utility gave me the "Congratulations" message and told me I've successfully upgraded. But then, the 8125 reboots, and unfortunately, it still hangs on the boot screen, and it still gives the OS as 1.5.4.2. Have tried a number of times, always the same:-(
Oh, I tried upgrading the Radio only, and it worked: I was able to upgrade to 02.61.11.
So, does it seem like there is hope, and can anyone think of what else I can do?
Click to expand...
Click to collapse
If I were you I might be talking to IMEI unlockers. Their process works from bootloader and might be able to get you CID unlocked and fix your corrupted CID area, which seems to be your major problem atm. In any case I would contact them and explain your situation and see if they think their software will unlock your phone. If so then you should be good to go once you CID is "uncorrupted" and unlocked.
one question: can You HARD RESET your device?
Do you have "format failed" message?
if so, you have 50/50 per cent for resurrection.
3.08 is not direct problem here anyway..., version is not exactly matter of problem...
(imei? now? lol)...
Thanks!
Yes, I can hard-reset fine and it claims to reformat fine.
Tx for the suggestion - I will contact IMEI (they unlocked my Trinity before the free unlockers were available
I was upgrading my t-mobile 8150(?) the k-jam with the new windows mobile 6 and in the middle of it my comp crashed!! now i am stuck at the bootloader mode (3 colored screen) and when i try to redo it i get to 99% and get a 302 error message. i follow the instructions given but keeps going in circles. its a G3 so is my phone bricked or is there a way to save it? i've been looking at this site all day but am now just more confused. lol thanks for your help!
No your phone isn't bricked. As long as you can get into the bootloader screen you should be ok. What you need to do is flash an official carrier rom either tmobile 2.26 or wizard love rom after you that than you can reflash to wm6. look at the stickies in the wizard forums that is where you can find these roms.
Thanks for the info but seems my techno curse continues. I tried the wizard love rom but it was in a different language and whem i tried the tmobile 2.26 i got "error 274 connection." Any more suggestions? Again thanks soo much for an issue I'm sure has been posted here a thouand times.
This happens to me all the time. I always use the Cingular 2.25 rom, it works perfectly and I have an I-mate K-JAM. Then, do the WM6 upgrade, but ensure all of your Norton and Antivirus and background running apps are shut down. Good luck.
yes also take out your mini sd card if you have one. even though its in another language it will work. "AVANTI means next. so just keep hitting that and you will be fine.
hmm been trying to d/l the Cingular 2.25 rom but the link seems to have stoped working...
It;s aaaaaaaaaaaaaaalllllllllliiiiiiiiiiivvvvvvvvvvvvvvvvveeeeeeeeeeeeeeeee!!! for now lol Lets see what happens after i install wm6 I couldn't get the cingular rom but i had already dowbloaded the button rom i found here earlier and it worked like a dream!! quick and easy!! thank you all soooooo much!
hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?
flash to the tmo 2.26 or cingular 2.25...that will give you an IPL/SPL of 2.xx
then, you can flash to WM6
i want to delete this message. can't find a way to do it.
there's any other way to flash without usb cable?? sorry to bug in this thread but i lost my usb connection somehow and did a hard reset and still doesn't work. my phone charges. and no is not my computer cuz my wifes phone same as mine does sync i have a tmobile mda also known as the cingular 8125.
fallon75 said:
hi all. one more little thing. after adding the new rom to get it back to life, now the numbers don't match so i can't upgrade to wm6. i have ipl 1.01 spl 2.26. advice?
Click to expand...
Click to collapse
keep reflashing buttons rom until both ipl/spl are the same number. if they are different, then the flash didn't complete correctly. (it happens often, so it's kinda normal). just keep reflashing. after both ipl/spl are the same, then CID unlock and then update to an official carrier...then flash a wm6.
can anyone help me??
Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.
starkwong said:
Check if "USB" displayed when in bootloader mode (Camera+reset) with Wizard connected to PC.
If so, you may try to flash another ROM through bootloader.
Click to expand...
Click to collapse
it does shows but how can i flash?? it still won't connect o my pc. my pc doesn't recognize it. but it does recognize my wifes phone.
Try to run RUU straight with Wizard connected and running in bootloader mode
hi all,
i uploaded my g3 with this rom Molski.Biz_AKU3.3_21911_8MB_Crossbow.exe. in the beginning everything is normal. it normally finished upgrading. then it restarted automatically, but my g3 didnt open. it shows always bootscreen. ipl and spl both 1.03.
i read almost all forum. when i try hard reset it says "format is ok" but nothings change.
and when i try upgrading with another roms. it gives ERROR 260 NO CONNECTION.
how can i fixed it? pls help me.
read the flashing tutorial..
Start in bootloader
kill activesync *(wcescomm process in taskmanager)
reflash..
BTW WM6 requires 2.X IPL/SPL !!!
If you read almost all the forum, you must have missed a few pages. The reason it won't start up is because you have an IPL/SPL of 1.03. With the phone off and connected to the usb cable, press and hold the camera button and then press the power button. Don't release the camera button until you get a 3 colored screen. That's the bootloader. Now flash an official ROM such as T-Mobiles 2.26 to get your IPL/SPL to at least 2.xx (if you flash T-Mobiles ROM they will be 2.26). After you do that you can flash Molski.Biz's ROM or any other ROM of your choosing.
I just want to add to all the correct things said here that sometimes "No Connection" errors come from low voltage battery. Be sure to have it fully (or almost) charged!
xeno1 said:
If you read almost all the forum, you must have missed a few pages. The reason it won't start up is because you have an IPL/SPL of 1.03. With the phone off and connected to the usb cable, press and hold the camera button and then press the power button. Don't release the camera button until you get a 3 colored screen. That's the bootloader. Now flash an official ROM such as T-Mobiles 2.26 to get your IPL/SPL to at least 2.xx (if you flash T-Mobiles ROM they will be 2.26). After you do that you can flash Molski.Biz's ROM or any other ROM of your choosing.
Click to expand...
Click to collapse
i did all what you said. ecxept trying the t-mobile 2.26 rom. coz i couldnt find it. i got 3 colored screen and i tried another rom and it gives sama error (260 ERROR) it is look like has no connection so rom update couldnt find ppc
Look here for T-mobil 2.26
http://forum.xda-developers.com/showthread.php?t=310831
no it didnt work. as i said when in 3 colured screen, there is no connection between my computer and ppc. so it always gives same error: ERROR 260. it says "no connection" check usb cable etc.
by the way there is no problem with usb cable.
i think there is another method to rom update. can i copy any rom to my sd card by using ntrw.exe.
do you think it is work. if it is so, can anyone explain me details
thnx
hi forum members(people who have the best knowledge about pocket pc).
i dont know what i did but my wizard is working now. i did what i alwyas did before, i mean in serial mode i tried to update wizard, today i want to try again then it is ok.
thnx for helping....
I have a wizard (wiza110) running wm5 and i wanted to upgrade it. It was the first time i was trying such thing. I was following these instructions http://wiki.xda-developers.com/index.php?pagename=Wizard%20Windows%20Mobile%206%20for%20newbies. My device is g3. My first attempt was with Button Rom, everything was fine until 99%... i think it was error 302 or something. I took off the battery and plugged it again several times but nothing came out. I had the three-colour screen.
Then I tried The Xda_MiniS_LaunchROM_v154102.exe, still nothing, lokiwiz also...
Last attempt was with wizard Love. USB appears but the ruu can't see the device and stops the process
Any ideas?
i think the device was sim-unlocked...
Flash back to the original rom, charge the battery to 100%. Make a guest connection to windows and start reading this thread from the beginning
do you have a link for the original rom? the thing is that ipl is 1.05 and spl is 2.25
aposperitis said:
do you have a link for the original rom? the thing is that ipl is 1.05 and spl is 2.25
Click to expand...
Click to collapse
Based on my experience and what I've read here, I'm guessing that your original rom had ipl and spl both 2.25. When you installed the button rom, it updated the ipl but nothing else. Just a guess, but that's what happened to me the first time on my G3. I just re-flashed button rom and continued from there. You should try to find the original rom for whatever kind of phone you have (I mean, the rom from the service provider like Orange, AT&T, etc). Their latest rom might not be 2.25. For example, my phone originally came from T-Mobile. I have the T-Mobile rom that is I think 2.26. I keep it handy, but have only reflashed back to that rom once when my extended rom got messed up.
Read the link suggested above. Good stuff. It is possible to flash a phone that is stuck on the tri-color screen, but it might not work the first try.
Same thing here, just youre getting further
I have ipl and spl on 2.26 received it this way. It's G3. I've been a week looking through the forums. Trying to avoid posting here. But damn it. I can't seem to get anything right. I previously had the G1 and Juno, Flashing was a breeze. But here i feel lost.
Basically my problem is i can't get it to downgrade. upgrade. CID unlock, With neither Lokiwiz or WST. A pain. And really NO RUU runs past the 0% it reboots my phone to boot loader image and USB shows but it reads that it can't find my phone anymore. It's been charged to 100%. Deleted TEMP folder. Was guest under activesync. Changed my USB cables 10 times. It's frustrating. Please. Any suggestions??