Database Develop

After soft reset my Wizard cannot boot up system

I've installed Softick Card Export II v2.12 in order to get a useable mass storage device.
There was a message that I should not run Card Export before I soft reset device, which I did.
BUT, big but, there was O2 logo, then WindowsMobile logo and then light turned off..five minutes later the Windows logo was still on the screen and my Wizard cannot boot up system completely. Holding Power button doesn't do anything,so I had to press that small Harr reset button. I tried one more time, leavin the phone on for 15 minutes, but the story was the same..Windows Mobile..and nothing else. Even keyboard and green/red button stopped being lit.
I can hear on my speakers that the phone is working (electric iterference).
I thought I could just put new ROM over it, but then saw that I need a working ActiveSync connection in order to do that.
Please, does anyone have an advice on what to do?[/url]

Any 3..4..5 button-combinations that could reset the device and format internal memory?

Hold VoiceDial + CommManager button and press the soft-reset button, then press the Send button (Green button) to hard-reset your device.
Why did you install v2.12 because v2.17 is already released?
It's better to install WM5torage 1.60, it does the same and is freeware and works A LOT better!

Thanks a million!

blackberry connect install problem / reboot frozen screen

I've searched the forums, and can't find a report of anything similar...so this might be new...if it isn't, help locating a thread would be great.
- Downloaded Blackberry connect install cab
- Seems to install fine (log looked good before reboot)
- Press "ok" to reboot device, but upon reboot, the device screen is locked at the Windows Mobile screen
The unit seems to be operating fine... I can receive calls - the phone rings, the caller ID pops up, but it stays on top of the Windows Mobile boot screen...
The power button will not shut the unit off...only turns the locked screen on and off
Battery removal and reboot freezes at same spot.
I had deselected all the ActiveSync options including the 'connect via USB' option... and now can't view my device from my laptop...
I've had the TILT only a couple of days...I'm running the stock ATT Tilt ROM & software...added two themes (night palms and the planet reflection ones)... have a 6G microSD card with some songs, pictures, and a device backup...
Looking forward to your suggestions & solutions!!

I tried it on mine and it did the same. So I gave up and did the hard reset and started over without even attempting to install the bb connect.

after hard reset
thanks for the quick response...
the hard reset worked fine...
I repeated the bbconnect setup, this time installing to the device instead of to my card... everything worked fine.

How did you do a hard reset on it?

hard reset
a hard reset will wipe all your data and set it everything back to the default status...it isn't supposed to clear anything on your sd card ... i take mine out anyway.
to do a hard reset, hold both the soft buttons while pressing the reset button w/ the stylus (the reset button is on the bottom edge under the hard OK button )

wprocter said:
a hard reset will wipe all your data and set it everything back to the default status...it isn't supposed to clear anything on your sd card ... i take mine out anyway.
to do a hard reset, hold both the soft buttons while pressing the reset button w/ the stylus (the reset button is on the bottom edge under the hard OK button )
Click to expand...
Click to collapse
One thing the instruction did not say rright was to hold the two soft keys and then press the reset then release and wait for the screen to give the instructions. Well the real way is to hold all 3 and wait and the process will be on its way.

wprocter said:
a hard reset will wipe all your data and set it everything back to the default status...it isn't supposed to clear anything on your sd card ... i take mine out anyway.
to do a hard reset, hold both the soft buttons while pressing the reset button w/ the stylus (the reset button is on the bottom edge under the hard OK button )
Click to expand...
Click to collapse
this is just not working for me, how long are you pressing the stylus in? how long are you holding the buttons?
When I do it I get the AT&T logo screen (a short vibrate) then it continues to the windows mobile boot screen. I can never get the prompt to erase all data. I've tried the procedure a dozen times, no luck.

Make sure you are pressing the soft buttons and not the 'call' and 'end call' buttons as stated on some sites. Hold those and press stylus into reset until it turns off. Continue holding the buttons until the message comes up.
I've just had to do this for exactly the same reason!

I had the same problem on my Touch. After the hard reset I have found a solution: install application to device memory not on storage card. That helped me and now BB Connect is working fine.

TyTN II shutting down after Green Windows Mobile Screen

I really don't how how this problem has cropped up. Have had my TyTN II for the past 6 months and suddenly today afternoon it was off when I tried to use it. While turning on, it went upto the Green Windows Mobile 6.1 screen and then it simply turns off. What is the problem? Have tried a hard reset and still have the same problem.

Have you tried re-flashing your phone, with the original manufacturers rom.
enter bootloader by holding the camera button and pressing soft-reset.
then try connecting via USB and running your manufacturers rom update.
this will wipe all your data, but chances are, if you have already hard-reset then you will have lost all data.

I had made no changes to the ROM. It had the stock HTC Windows Mobile 6.1 ROM included.

try taking out the sim and sd card, then hard reset.

OK, it boots up without the SIM Card but not with the SIM card. Tried another SIM card but same problem. What could be the problem? My SIM card is working fine on other phones!

blue_earth said:
OK, it boots up without the SIM Card but not with the SIM card. Tried another SIM card but same problem. What could be the problem? My SIM card is working fine on other phones!
Click to expand...
Click to collapse
Is the sim card door locked and closed properly? There's a little microswitch that shuts down the device if it senses the door isn't locked it's possible for this to not be correctly aligned with the lock pin (ie not in the groove). Turn it off and take a good look at the mechanism and you'll see what I mean.
Additionally, you mention you'd tried a hard reset - did you try this with the sim and memory card out from within WM? Did the process complete properly?

I tried booting with 2 other sim cards and with them it says that there is no sim inserted. With my original SIM, it simply shuts off at the green windows mobile screen.
@Flying Kiwi, Yes, the SIM door is closed properly with that little notch extended to the right. The hard reset was done not from with WM but by the method given in the manual i.e keeping the 2 soft keys pressed and hitting the reset pin. This was done at the Smart Mobility screen with SIM and Memory Card inserted. The process did complete properly but while booting it shut off. So I removed the SIM and this time it went all the way to the screen alignment page and customizing stage. Now, it does not work with any SIM card but boots up fine without SIM.
I'm completely at a loss.

It could be a bad sim holder (surely there is a better word) or something like that. I would suggest playing around with it by opening the keyboard and then applying pressure on the door while it boots.

blue_earth said:
Flying Kiwi, Yes, the SIM door is closed properly with that little notch extended to the right.
Click to expand...
Click to collapse
It was a long shot because with my TyTN II if I try that (with the WM 6.0 ROM) it gets all the way into WM and pops up a message about the sim door saying it'll shut down in 10 s - making it very clear - I've never tried it under WM 6.1 though.
Now, it does not work with any SIM card but boots up fine without SIM.
Click to expand...
Click to collapse
Could still be some sort of ROM corruption so what I'd like you to try is to remove BOTH the sim and memory card and boot into WM then perform a hard reset from within WM (settings -> System tab -> Clear Storage) and see if that runs right through to the end - then power off normally by holding down the power button and tapping yes. Then put in just the sim (that used to work fine with this phone) and start up again. Let us know how that goes Also have a look for any dirt/contamination in the sim slot as best as you can see, and on the sim itself.

KOVS100 or KOVS110?

Someone please help me. I have installed HARDSPLV1 and everything appeared to be working, but every time I put a ROM on my storage card as Kovsimg.nbh and enter the bootloader tricolor screen it just says
KOVS100
SPL-0.72.OliNex
MicroP1-787
MicroP2-707
then Serial in the white part
then it says Loading...
No Image File!
What am I doing wrong? I have tried 2 different sd cards and 2 different ROMS with the same result. Someone please help if they can!

Have you unchecked "hide extensions of known files types" in Folder Options and made sure it isn't 'kovsimg.nbh.nbh' ? (I've seen this case, back a few months ago.. the creator of the thread never listened though)
What is the filesize of the rom you've placed onto the SD card(s)?
What was the filename+extension of the file before you renamed it? ruu_signed.nbh or was it some .zip or .rar?
There's other causes of this error, but just making sure the fundamentals are done correctly

Thanks to the above poster for offering his help^
However, I got it working, the problem was I didnt format the storage card with FAT32 prior to putting the Kovsimg.nbh file on it. I discovered you DO NOT need a card reader to do this on your PC. The X1 can act as a card reader when you set the option to disk drive select the disk drive in my computer after connecting the device and Format it with FAT32 there.
One thing though worrying me, I was not able to do a hard reset after installing the ROM onto my device, I tried depressing the two silver buttons while also depressing the power button and waiting for hard reset prompt to appear, but the device simply botted up as normal. Although, everything seems to be working fine without the hard reset. Any advice?

a hard reset is holding those silver buttons on the front and the button at the back of the phone, take off the metal cover and take out the stylus and you will see a circle, stylus covers it the button, hold that button too with the silver ones when on.

Oh word. well I was going by what BioVolt said in his tutorial... he said hold down both silver buttons and power button... but what you said makes sense since that didnt work,
Do you think I should hard reset the device even though the ROM has already been set up and everything seems to be working smoothly?

JoLLAJoLLA said:
Thanks to the above poster for offering his help^
However, I got it working, the problem was I didnt format the storage card with FAT32 prior to putting the Kovsimg.nbh file on it. I discovered you DO NOT need a card reader to do this on your PC. The X1 can act as a card reader when you set the option to disk drive select the disk drive in my computer after connecting the device and Format it with FAT32 there.
One thing though worrying me, I was not able to do a hard reset after installing the ROM onto my device, I tried depressing the two silver buttons while also depressing the power button and waiting for hard reset prompt to appear, but the device simply botted up as normal. Although, everything seems to be working fine without the hard reset. Any advice?
Click to expand...
Click to collapse
Even I had this problem of hard resetting my X1 initially while flashing ROMs. Then I found out that the trick lay in pressing down the two silver buttons and pressing the power button and the moment the phone gives the initial vibration, to release the power button. This way, you would be able to get into the hard reset screen. Try this and see.
And yes, I think a hard reset is advisable.

shantanil said:
Even I had this problem of hard resetting my X1 initially while flashing ROMs. Then I found out that the trick lay in pressing down the two silver buttons and pressing the power button and the moment the phone gives the initial vibration, to release the power button. This way, you would be able to get into the hard reset screen. Try this and see.
And yes, I think a hard reset is advisable.
Click to expand...
Click to collapse
Thank you for your advice, so you think a hard reset is a good idea even after the ROM is loaded and set up working properly? if you advise this I will do it.

JoLLAJoLLA said:
Oh word. well I was going by what BioVolt said in his tutorial... he said hold down both silver buttons and power button... but what you said makes sense since that didnt work,
Do you think I should hard reset the device even though the ROM has already been set up and everything seems to be working smoothly?
Click to expand...
Click to collapse
u have to press both silver buttons and then just press power button once and let it go right away that should do the trick

republicano said:
a hard reset is holding those silver buttons on the front and the button at the back of the phone, take off the metal cover and take out the stylus and you will see a circle, stylus covers it the button, hold that button too with the silver ones when on.
Click to expand...
Click to collapse
hard reset is just pressing 2 silver buttons and pressing power button, but you have to release the power button after the phone vibrates. thats all

JoLLAJoLLA said:
Thank you for your advice, so you think a hard reset is a good idea even after the ROM is loaded and set up working properly? if you advise this I will do it.
Click to expand...
Click to collapse
If your ROM is set up and working properly, then there is no need of a hard reset.
I usually flash through the SD Card method. After successful flashing message is displayed, I restart the phone and immediately perform a hard reset. Hope this helps.

^ thank you. Originally when I got the successful flashing message, I took the battery out and tried to do a hard reset. To this day, it hasnt allowed me to do one. instead of going the the hard reset prompt, the device always just boots up normally. Ive tried all different ways, hard reset by holding the two silver buttons and power button, and by holding the two silver buttons and just pressing the power button, hard reset by holding the reset button behind the batterycover with stylus and holding the silver buttons. All the same thing, just get the Sony Ericsson screen and the device starts up. I have spikegotti X1.5 6.5 ROM btw.

Hd7 stuck on htc logo

Hello, my HTC after update stoped working... im can turn it on,only if the phone is on the usb or charger.. when my phone turn on, its stays on HTC LOGO screen with white background...I tried to get in bootloader, but im cant,, im tried hard reset but im can get in that menu... im holding down buttton and power, then im insert usb in computer, but nothing, still stay on htc logo!
EVERYBODY HELP ME :victory: :silly: :crying: :cyclops:

Try:
- hold down - + and Power to go in reset mode.
or
- hold down the camera button and power now phone starts int Download Mode Connect with your PC and start Zune or WP Support Tool
try to fix.
I don't think your phone is Dead, only Corrupted ROM .........
do you changed you SD CARD?

there isnt micro sd in my phone,,, im pull out micro and sold it..cant get into bootloader

Galaxy3HELL said:
there isnt micro sd in my phone,,, im pull out micro and sold it..cant get into bootloader
Click to expand...
Click to collapse
lol
so there is no micro sd in your phone?
hd7 internal memory is sd card

What to do then? ima have european HD7 with 8GB

can you get into Downlaode Mode?
think it was Camera und Power Button? or vloume + , - and camera button don't
know and my camera button is Broken so I cant test it yet.
If you can get into downlaod Mode you can try to connect with Zune.
I'm absolutely sure that your phone isn't broken only bad rom or whatever else.
Or if you Live in the near of Frankfurt a.M. in germany we can meet us and I can get my hands on your Phone *g*
the problem with the SD Card is that, if you changed them you often get problems on starting your Phone.
Don't give up try all you can try. Left the battery out of the phone wait 15min. and try to rest your Phone again....

Well, phone turn on to HTC only if its on charger or usb.. im cant get into download mod or into recovey mod.. buttons are lazzy bit lit.. im have no micro SD card in phone.. what to do? ima live in Bosnia

put out your battery and wait a day then try again

Okey im will try..

u must get a microsd card in
some supported sd
http://forum.xda-developers.com/showthread.php?t=883582/