After soft reset my Wizard cannot boot up system - 8125, K-JAM, P4300, MDA Vario Software Upgrading

I've installed Softick Card Export II v2.12 in order to get a useable mass storage device.
There was a message that I should not run Card Export before I soft reset device, which I did.
BUT, big but, there was O2 logo, then WindowsMobile logo and then light turned off..five minutes later the Windows logo was still on the screen and my Wizard cannot boot up system completely. Holding Power button doesn't do anything,so I had to press that small Harr reset button. I tried one more time, leavin the phone on for 15 minutes, but the story was the same..Windows Mobile..and nothing else. Even keyboard and green/red button stopped being lit.
I can hear on my speakers that the phone is working (electric iterference).
I thought I could just put new ROM over it, but then saw that I need a working ActiveSync connection in order to do that.
Please, does anyone have an advice on what to do?[/url]

Any 3..4..5 button-combinations that could reset the device and format internal memory?

Hold VoiceDial + CommManager button and press the soft-reset button, then press the Send button (Green button) to hard-reset your device.
Why did you install v2.12 because v2.17 is already released?
It's better to install WM5torage 1.60, it does the same and is freeware and works A LOT better!

Thanks a million!

Related

blackberry connect install problem / reboot frozen screen

I've searched the forums, and can't find a report of anything similar...so this might be new...if it isn't, help locating a thread would be great.
- Downloaded Blackberry connect install cab
- Seems to install fine (log looked good before reboot)
- Press "ok" to reboot device, but upon reboot, the device screen is locked at the Windows Mobile screen
The unit seems to be operating fine... I can receive calls - the phone rings, the caller ID pops up, but it stays on top of the Windows Mobile boot screen...
The power button will not shut the unit off...only turns the locked screen on and off
Battery removal and reboot freezes at same spot.
I had deselected all the ActiveSync options including the 'connect via USB' option... and now can't view my device from my laptop...
I've had the TILT only a couple of days...I'm running the stock ATT Tilt ROM & software...added two themes (night palms and the planet reflection ones)... have a 6G microSD card with some songs, pictures, and a device backup...
Looking forward to your suggestions & solutions!!
I tried it on mine and it did the same. So I gave up and did the hard reset and started over without even attempting to install the bb connect.
after hard reset
thanks for the quick response...
the hard reset worked fine...
I repeated the bbconnect setup, this time installing to the device instead of to my card... everything worked fine.
How did you do a hard reset on it?
hard reset
a hard reset will wipe all your data and set it everything back to the default status...it isn't supposed to clear anything on your sd card ... i take mine out anyway.
to do a hard reset, hold both the soft buttons while pressing the reset button w/ the stylus (the reset button is on the bottom edge under the hard OK button )
wprocter said:
a hard reset will wipe all your data and set it everything back to the default status...it isn't supposed to clear anything on your sd card ... i take mine out anyway.
to do a hard reset, hold both the soft buttons while pressing the reset button w/ the stylus (the reset button is on the bottom edge under the hard OK button )
Click to expand...
Click to collapse
One thing the instruction did not say rright was to hold the two soft keys and then press the reset then release and wait for the screen to give the instructions. Well the real way is to hold all 3 and wait and the process will be on its way.
wprocter said:
a hard reset will wipe all your data and set it everything back to the default status...it isn't supposed to clear anything on your sd card ... i take mine out anyway.
to do a hard reset, hold both the soft buttons while pressing the reset button w/ the stylus (the reset button is on the bottom edge under the hard OK button )
Click to expand...
Click to collapse
this is just not working for me, how long are you pressing the stylus in? how long are you holding the buttons?
When I do it I get the AT&T logo screen (a short vibrate) then it continues to the windows mobile boot screen. I can never get the prompt to erase all data. I've tried the procedure a dozen times, no luck.
Make sure you are pressing the soft buttons and not the 'call' and 'end call' buttons as stated on some sites. Hold those and press stylus into reset until it turns off. Continue holding the buttons until the message comes up.
I've just had to do this for exactly the same reason!
I had the same problem on my Touch. After the hard reset I have found a solution: install application to device memory not on storage card. That helped me and now BB Connect is working fine.

Is my wizard totally bricked?

hi, please! need help... after I've flash the
Wizard_Love_2.26.10.2_WWE_Novii_CF2 on my G3 device the rom is very slowly and my PC doesn't recognized my wizard when it connected with the USB cable.
any solution how can I change this rom?
many thanks
i can go to the tri-color bootloader mode, is it say somthing?
mine did that yesterday....maybe try a hard reset:
Hold down the Comm Manager button(top left) and Voice Command button(top right) buttons while performing a soft-reset (depress the reset button using the stylus); after you depress the soft-reset button, [contintue to hold the two side buttons] hold down the navigation pad for ~4 seconds until you are prompted on screen [you can release the side buttons now]. Press the Send (Talk) button (i.e. the left telephony button) - or whichever button your system prompts you for.
That's what I did and it worked for me =)
thanks but it doesn't work, the main problem is that after the hard reset the rom is very very slowly (like 7-8 seconds from the moment you tap the "start" till the start menu come)
the PC doesn't recognized my wizard so i can't change to another rom....
I can get into the tri-color mode, does it say that maybe it's not bricked?

Diamond freezes upon startup - No Sync Connection

Hi there,
i recently flashed this Rom: /ROM\WM6.5|23017&23060|Benko's 4.9ROM's|NEW| Full, Prime&Clean[Manila2.1 R1.5/16.10]
and everything was working fine. Then i installed some program (SPB Diary). And since then my Diamond keeps on freezing up upon startup. It shows the Notifications Windows (Network provider, Battery status, "No new notifications" and the "close" button at the bottom).
But then he wont react to anything. He doesnt establish a connection to my computer, so i cant flash a new rom on my device either.
Im totally lost, can someone help me?
Che
che27 said:
Hi there,
i recently flashed this Rom: /ROM\WM6.5|23017&23060|Benko's 4.9ROM's|NEW| Full, Prime&Clean[Manila2.1 R1.5/16.10]
and everything was working fine. Then i installed some program (SPB Diary). And since then my Diamond keeps on freezing up upon startup. It shows the Notifications Windows (Network provider, Battery status, "No new notifications" and the "close" button at the bottom).
But then he wont react to anything. He doesnt establish a connection to my computer, so i cant flash a new rom on my device either.
Im totally lost, can someone help me?
Che
Click to expand...
Click to collapse
you will have to hard reset, when u switch ur diamond on, hold volume down, the big round button and hit the red reset button under the stylus, do this while windows is booting b4 it freezes..... i had a simlar problem with spb mobile shell ageees ago lol
I tried then, then i see the 3 colored screen, then it says "No Image File" on a grey screen, then it says "trigger usb host" and "retry entry usb" (does the a few times), then it goes back to the 3 colored screen after a while of waiting, and it says "USB" in the center.
But thats it, problem still there
Any idea?
no if that appears your holding the back button not the round centre button
Thank you so much for your help, i though hard reset was hard reset either way, didnt know that there was a difference between which of the buttons (back, hang up, center) to press.
My Diamond is up an running again, Thanks for the help!
BTW: What exactly are the different modes of hard resetting for? Is there a manual somewhere?
che27 said:
Thank you so much for your help, i though hard reset was hard reset either way, didnt know that there was a difference between which of the buttons (back, hang up, center) to press.
My Diamond is up an running again, Thanks for the help!
BTW: What exactly are the different modes of hard resetting for? Is there a manual somewhere?
Click to expand...
Click to collapse
The method you described is for flashing a rom from your internal storage... Next time you download a rom, take the .nbh file and change its name to DIAMIMG.nbh, Then copy it to the root of the internal storage, if you then hold vol down, the back button and press the red reset button, you can flash the rom without using a ruu, this way is also alot faster then the old method

HELP - HARD-RESET and POWER button not working

Hi guys!
Yesterday my Kaiser hang and I had to do a Soft-Reset. Now, it boots into windows and immediatelly resets...I tried to make a Hard-Reset but it seems the soft buttons doesn't work, although they work fine in Windows...
After that I tried to flash a new ROM via SD card but when I press the Power Button to start the update, it does nothing, nor the Action Key to Cancel...
Do you have any idea of what it can be? I really need some help because I cant do anything with it....
Regards!
et_pedro said:
Hi guys!
Yesterday my Kaiser hang and I had to do a Soft-Reset. Now, it boots into windows and immediatelly resets...I tried to make a Hard-Reset but it seems the soft buttons doesn't work, although they work fine in Windows...
After that I tried to flash a new ROM via SD card but when I press the Power Button to start the update, it does nothing, nor the Action Key to Cancel...
Do you have any idea of what it can be? I really need some help because I cant do anything with it....
Regards!
Click to expand...
Click to collapse
I think you are not doing the hard reset properly, since you are stating that the buttons work while you are in windows. Retry and see what happens.
Yeah does sound like you need a hard reset and aren't doing it properly. 2 ways to do it listed below:
-Press and hold the Left & Right SOFT KEYs and at the same time use the stylus to press the RESET button. Release the stylus but keep pressing the SOFT KEYS until you see the Hard Reset warning screen. Release the SOFT KEYS and then press the LEFT PHONE KEY.
-A software option is also available. Start> Settings> System> Clear Storage.
Type 1234 in the box and tap YES.
Sorry for the silence guys...
I'm doing the Hard Reset OK, but the phone simply doesnt do it...
Also the Power button doesnt work when installing a new ROM with SD Card...
My phone is in a continuous soft reset :s

Diamond not going to boot loader

Hi,
Diamond is not going to bootloader (tricolour) screen after MTTY. MTTY was successful but nothing happening after pressing volumedown+center button.
Now device is just showing - Touch diamond when i switch on.
I have diamimg.nbu on internal storage, is there any way to trigger install.
It was working fine before mtty.
Pull battery out to turn it off.
Put it back in.
Press and hold volume down
Press reset button.
The reason its only showing Touch Diamond is that the MTTY process has cleared off your previous OS. You need to get it back to bootloader and try MTTY again.
I have tried all those stuff but no luck, for every thing diamond just vibrates and shows "Touch Diamond".
I guess boot loader is not working, is there any way to connect to it and repair bootloader.
I have tried snoopy from some post but thats also of now help.
Taken from PPCGeeks:
"Hold down the Volume down key and power button, the take the tip of your stylus and press the soft reset button (bottom left corner of phone under battery cover). After you press reset button keep the Volume down and power button press until the bootloader screen comes up"
Let us know if this works.
Thanks Super....
This is not working, only option i see is some way to connect to it through USB because i had faced this problem earlier also but that time RRU updater used to push it to bootloader.
volume down button used to work only with original HTC ROM for me....only a few time it used to work with cooked ROMs....
Hi,
Anyone can suggest some advance tool which can connect to diamond if its not going to bootloader through normal methods.
Its all clear by MTTY, i have ROM image on internal storage.
Solved finally.......
Hold only volume button pressed, press reset button and immediately after that press ok or back button

Categories

Resources